Milwaukee tools
“My Milwaukee tools are the very best. I’ve had my two 1/2-in. Magnum Hole Shooters for…”
1028 reports
“My Milwaukee tools are the very best. I’ve had my two 1/2-in. Magnum Hole Shooters for…”
“My best product is the Pinch-A-Log from Northwind Tools (Vol. 37, No. 6; www.northwindtools.com; ph 208-215-5472).”…
Photo: FARM SHOW“I’ve used Woodpeckers Tools for quite a few years, and they’re all excellent quality (www.woodpeck.com; ph…”
“My best buy is a Stihl Multi-Task Tool. It wasn’t cheap, and I looked at it…”
“I usually research the tools I buy ahead of time, so I can’t really say I’ve…”
“Years ago, I bought a Delta table saw from a Delta dealer. When I began using…”
“I’ve had great service from Milwaukee drills, impacts, Sawzalls, pole saws, etc. I wore out two…”
“My Oreck XL Pro commercial vacuum cleaner is both a best and a worst buy.”…
“I do a good bit of welding. That requires grinding, and over the years I’ve used…”
Photo: FARM SHOW“I’ve enjoyed building many woodworking projects in retirement and learned early on that premium-quality tools make every job a little easier.”
Read the whole story →Read more at FARM SHOW →“A best buy for me has been my Milwaukee magnetic drill. It’s probably one of the…”
Farrell is impressed with his Worx 20V Switchdriver. “I can predrill, then, with a twist, switch…”
“All of my Milwaukee tools are great buys. I have a weed eater, chainsaw, air compressor…”
“I’ve been pleased with DeWalt 20V MAX tools. I’ve purchased and used several over the past few years, including drills, impact drivers, a weed trimmer and a chainsaw. The most recent is a jump-start booster. It’s compact and uses a single 20V battery. I haven’t run the battery pack down with the booster. I like that the battery pack can be swapped out like any other tool, unlike other boosters that have to be recharged when run down. It works great.”
“My best buy is a wire hoe with interchangeable heads from Neversink Tools (www.neversinktools.com; Vol. 46, No. 5).”
“I’ve had my Makita 18V 1/2-in. impact for about 6 years. It’s got plenty of power, and the battery lasts a long time between charges. It’s a good tool.”
Photo: FARM SHOW“I can’t say enough good things about Evolution Power Tools USA products (https://store. evolutionpowertools.com; ph 866-386-8665).”
Read the whole story →Read more at FARM SHOW →John is pleased with his Montana T-Rex 350E post driver (www.montanapostdriver.com; ph 800-330-1937). “We mounted it on our used Deere 35D compact excavator (also a best buy) for ranch fence work.
“My worst buy is my Klein Tools ET450 Advanced Circuit Breaker Finder. It wouldn’t come on and never did.”
Mike is impressed with his Can-Am Defender side-by-side UTV. “I looked at all the brands and found that Can-Am had the most storage compartments for tools and fencing supplies. The machine is reliable and powerful. I’m very satisfied.
“But I haven’t been satisfied with Chicago Electric tools from Harbor Freight. They’re very underpowered.”
“My best buys have been DeWalt and Milwaukee tools. Both brands work great.”
“Milwaukee tools are my best buys. I’m adding to my collection all the time. My latest purchase was the hedge trimmer. One of my batteries wasn’t charging fully. I spoke with a company rep and learned it was out of warranty. He still replaced my battery at no charge. Excellent customer service.”
“Our DeWalt tools are among our best investments. We’ve used the drills, impact wrench and reciprocating saw for years without any failures. Our batteries keep charging and recharging over and over.
“One of our worst purchases is a Polaris 450 Sportsman 4-wheeler. It needs more repairs than our Honda 4-wheelers. It’s heavier and always gets stuck in snow, while a Honda will just zoom right through.
“I’ll say the Honda Rancher 4-wheeler is a best buy. In fact, we started buying Honda 4-wheelers in 2004 after reading an article in FARM SHOW’s “Best, Worst Buys.” It told of a ranch where they had many Hondas that the help rode because Hondas were tougher than Polaris’s. We bought another Honda in 2010 and again in 2016. Unfortunately, we needed another 4-wheeler in 2020 and couldn’t get a Honda, so we had to settle for a Polaris.
“The 2010 and 2016 are still going strong, but the 2004 is retired. We have to baby the Polaris and keep it close to home. Give us a Honda any time.”
“My Chapman Mfg. Master screwdriver set (#5575), purchased in December 2024, is an awesome, made-in-the-U.S. set (www.chapmanmfg.com; ph 475-232-0802). It has all the bits I’ll need and is built to last. It can handle more torque than most. The set includes a 90-degree angle ratchet and a screwdriver-type driver. The ratchet is amazing and has helped me remove some ‘impossible’ fasteners. I use it regularly, especially for hard-to-turn fasteners. I take it back and forth between the shop and the house. Maybe I need another set?
“I haven’t had a good experience with the Milwaukee 18V Fuel 6 1/2-in. circular saw. After about a year, the first one stopped as if the auto-brake was fully engaged. The second one did the same. I never even wore out the blade. For warranty service, I needed to go to a repair center about 2 hr. away. I never seemed to have a day to do this, and arranging shipping was difficult. I finally tried one that isn’t a Fuel. It’s 18V and doesn’t have an auto-brake. It doesn’t have enough power for me, but it works.”
Photo: FARM SHOW“My Mr. Volcano forge was a really good deal. It only cost about $100, but it works great for heating metal for bending, hammering or working in some way.”
Read the whole story →Read more at FARM SHOW →“Harbor Freight frequently gets a bad rap, and I’ve had some disappointments myself. However, I’m well pleased with most of the air and hand tools they supply. Most notably, a Pittsburgh 16-piece combination wrench set. This is my most-used wrench set and is still going strong after nearly 30 years. Not bad for a set costing less than $20. Furthermore, they gladly honor their warranties, whereas some more expensive brands are very reluctant and accuse me of abusing the tools. A company isn’t obligated to offer a warranty, but if it does, it should honor it.
“I have a Ridgid 10-in. aluminum pipe wrench that broke right across the warranty logo. I never used a cheater pipe on this wrench. I haven’t been able to get a replacement because they no longer make that size. Harbor Freight would offer another size if it were one of their tools. I know because it’s happened a few times.”
“I bought a set of Makita cordless tools that included an impact driver, a hammer driver, two 18-volt 4Ah batteries, and a charger. I haven’t had any problems with them.”
“My DeWalt impact wrench (model DCF900) makes quick work of hard jobs. I’m pleased with all of my DeWalt tools.”
Steve is unhappy with his GE Reverse Osmosis Water Filtration System (model GXRV40TBN) purchased 15 mos. ago. “The delivery of water from the supply tank is 1/8 of the rated service flow. We’ve changed filters as directed. It takes 5 min. to get enough water to make a pot of coffee.”
“If I had bought it, my 1/4-ton JET lever-action chain hoist would be a best buy (www.jettools.com; ph 800-274-6848). I got it as a gift a few years back, and it’s come in handy more times than I can count.
“It’s a compact unit with a good-sized hook. I’ve used it to lift driveshafts on trucks when placing U-joints and to lift a clutch in a Versatile tractor. I’ve lifted shafts inside combines and other equipment, as well as pulling chains together on sugar beet lifters and many more.
“Its ability to precisely lift and lower a shaft or part without a lever makes it very handy. It’s made many jobs that require lifting or lowering and aligning parts much easier and safer.”