Real farmers rate what they bought, from FARM SHOW MagazineSubscribe  ·  Free issue  ·  Send us your Best or Worst Buy
Subscribe to FARM SHOW
Home › Issues › Vol. 22, No. 1 (1998)

Best & Worst Buys: FARM SHOW Vol. 22, No. 1 (1998)

77 reports from pages 14–17 · 73 Best Buys21 Worst Buys · See everything in this issue at FARM SHOW →

Best BuyWorst Buy

John Deere 9300 4-WD tractor equipped + 2 more

Allen Snodgrass, Vandalia, Mo. · Vol. 22, No. 1 (1998), p. 14

“My 1997 Deere 9300 4-WD tractor equipped with a powershift transmission is my worst buy. Every time I push on the clutch the transmission automatically goes to first gear, so I have to shift through all the gears to get to the gear I want. The tractor is equipped with the weights and tire size and pressure recommended by the company, yet ‘wheel hop’ is so bad I often have to stop, which puts the transmission back into first gear again. Another problem is that it shifts rough and jumps and jerks terribly. It had just 28 hours on it when I traded it for a Caterpillar Challenger. The Cat is a nice tractor to operate.” He’s impressed with his 1996 Dodge 3/4-ton pickup equipped with a Cummins diesel engine and 5-speed transmission. “It has a lot of power and gets 22 mpg on the highway and 14 to 15 mpg pulling a trailer, and it doesn’t use any oil. It rides nice for a 3/4-ton pickup and is a pleasure to drive.”

Best BuyWorst Buy

Great Plains no-till grain drill + 1 more

Dan Petersen, Curtice, Ohio · Vol. 22, No. 1 (1998), p. 14

“My worst buy is my 1994 Great Plains 10-ft. no-till grain drill which I bought in the fall of 1995. I like the drill itself - it does a good job of planting, saves time, and results in higher bean yields. I also believe wheat ‘winters’ better when it’s planted no-till because it doesn’t ‘heave’ so much in February and March. “I bought the drill from a dealer 95 miles away. When I got it home two of the seed-lock wheels had fallen off and were laying on the trailer floor. When I went to use the drill I found that I couldn’t adjust the seed rate because one of the plastic fluted seed metering wheels had been damaged. After fixing that problem I made only three rounds before it quit working because the clutch wouldn’t kick in. I took it apart and found that it was completely dry so I greased it. I made three more rounds, then stopped to check everything and discovered that I had lost two seed-lock wheels and mud scrapers. I went home and spent the rest of the day going over the drill with a fine tooth comb. “I called the dealer and was told ‘You should always check equipment over when you buy it’. However, he agreed to send me the parts that I had lost in the field. I received them, along with a bill which I didn’t pay. “When I planted my wheat field last fall I heard a squeaking noise coming from behind me, but the drill was still planting good. When I cleaned it up for winter storage I had my son oil all the discs. After he was done he said, ‘Hey dad, some of those opener discs are pretty loose.’ I checked some of them and found that about half of them were shot. “The dealer said the company would pay for only 40 percent of the cost because of the age of the drill. However, my drill has only about 600 acres on it because it was almost 2 years old when I bought it as a ‘leftover’ model. And I was told the discs would last 2,000 acres before needing replacement. “I think the company should make sure that its dealers do a better job of prepping these drills. I had to add 1,700 lbs. of weight to the drill so that it will penetrate my dry ground when the drill is one third or less full. I’ll add 400 more lbs. of weight next year. “All in all this drill is a great piece of machinery. I’d buy another one. But the problem with the opening discs is a good example of how a dealer can give a company a bad name.” Dan likes his 1995 Chevrolet K2500 4-WD pickup. “It’ll pull a 550-bu. grain load with no problem. It gets 13 mpg empty. It’s equipped with a new-style front suspension so it handles much better than older models. The only problem was with a front brake that occasionally wouldn’t fully release. The dealer promptly took care of it.”

Best Buy

Ram 3500 long wheelbase pickup

Ken Craven, Byars, Okla. · Vol. 22, No. 1 (1998), p. 14

“It’s all I could ever want in a truck for farm use, and more,” says Ken about his 1997 Dodge 3500 long wheelbase pickup equipped with a Cummins 3500 diesel engine, 5-speed transmission, and posi traction rear end. “I like it so much I wish we would’ve had it 15 years ago.”

Best Buy

M & W Pasture Clipper

Mark Bennett, Portland, Tenn. · Vol. 22, No. 1 (1998), p. 14

“It cuts like a lawn mower,” says Mark about his ‘best buy” 1990 M & W Pasture Clipper. “I’ve used it on about 4,000 acres and the only problem was when plastic twine got caught in a bottom gearbox reel. My neighbors borrow this machine a lot. I’d highly recommend it to anyone.”

Best Buy

Ford 8340 tractor

Edward Beeler, Hamilton, Ohio · Vol. 22, No. 1 (1998), p. 14

“My 1994 Ford 8340 tractor has a lot of power and a powershift transmission that works smooth and easy. This tractor is so nice to drive that I use it for both big and small jobs.”

Best Buy

John Deere 9600 combine equipped

Alan Stevenson, Ulysses, Kan. · Vol. 22, No. 1 (1998), p. 14

Alan has good things to say about his 1995 Deere 9600 combine equipped with a heavy duty front axle and 20.8 by 42 radial dual tires. “It’s an excellent machine that’s comfortable to operate and has had very few maintenance problems. It performs phenomenally in corn and also very well in wheat and milo. I really like the Deere-made dual wheels. In row crops the tires stay between the rows, allowing the machine to almost drive itself. The first year we used it we had a wet summer, so when I went to cut wheat I let the air pressure down in the tires to where they were pretty ‘cheeky’ with a load on. However, even with a 30-ft. platform and a full 350 bu. grain tank (it’s equipped with a Mauer tank extension), the combine was able to stay on top of the ground and keep going while I would look around and see my neighbors’ 9600s mired down with their 30.5 by 32 tires. The ground was so wet that my 95-ft. Deere 8400 MFWD tractor had trouble pulling even a half-loaded 840 grain cart around. “I’m also well pleased with the Deere 8400 tractor. It’s a real horse.“

Best BuyWorst Buy

Case-IH 7230 front wheel assist + 1 more

Jeff Dittmer, Suisun, Calif. · Vol. 22, No. 1 (1998), p. 14

Jeff’s the owner of a “best buy” Case-IH 7230 front wheel assist tractor. “The best thing about it is the dependability. We’ve used it for two years with no problems. It has about the same horsepower as the Ford tractor that it replaced but pulls everything easier and smoother. Its better balanced, too, and compacts the soil less than the Ford - we can see the difference. The salesman told us we could do the same job by buying the company’s next smaller model, the 7220. We didn’t follow his advice, but I think he was right. “Our worst buys are Ford tractors - we’ve had two that were nightmares. The big one, a TW-30 model, required regular 4,000-hour engine replacements. It was poorly built in terms of maintenance and repairs and always seemed to be breaking down. The smaller model, a 5610 that we bought new, had problems from day one. One cylinder wall on the engine turned to Swiss cheese at 900 hours. The rear end made a noise which turned out to be caused by a missing part that was left out during manufacture. A fuel problem was worked on by two different dealers without success until after the tractor’s warranty had expired. At that point the company rep refused to pay for it even though the problem started long before the warranty expired. I had to sue the company in order to get compensation. When the company lawyers heard the story they ordered the rep to pay up. “We also have a 1958 Ford 950 tractor. I can vaguely remember my dad taking delivery of it when I was a small child. It’s still going strong today. The only real repair ever done to it was a new paint job.”

Best Buy

Roundup Ready soybeans + 1 more

Rod Van Overscheld, Letcher, S. Dak. · Vol. 22, No. 1 (1998), p. 15

Rod’s pleased with Roundup Ready soybeans. “Weed control was very good. After spraying Roundup I had almost perfect grass and broadleaf control except for late nightshade. The Roundup Ready beans yielded about the same as our non-Roundup beans. However, I don’t like the $5 per bag surcharge. How long will the surcharge last? Forever? “My 1973 Deere 6600 combine had trouble with the drive belts on the auger that delivers grain into the hopper. I solved the problem by using a hydraulic motor to operate the auger. I control auger speed from the cab. I use the same hydraulic system to operate the reel on both the straight head and bean head. The oil goes first to an orbit motor on the hopper. The return line goes to the orbit motor on the straight head, then back to the oil reservoir. It works perfect this way. I didn’t have enough hydraulic capacity to put a ‘T’ in the hydraulic hose line and send it to both motors at the same time.”

Best Buy

Ram pickup equipped

James Sprunk, Columbus, Neb. · Vol. 22, No. 1 (1998), p. 15

“I’m well pleased with my 1997 Dodge Ram pickup equipped with a diesel engine. It’s very easy on fuel and has a lot of lugging power. I can use it to pull an anhydrous ammonia tank with no problems. I can’t say enough good things about this pickup.”

Best Buy

Gates Mfg

Walter Rude, Langdon, N. Dak. · Vol. 22, No. 1 (1998), p. 15

“We bought some new harrow teeth from Gates Mfg. that weren’t any good. As soon as we started to use them they broke. The old small teeth worked a lot better.”

Best Buy

Huskee riding mower

Blake L. Tyson, Wayne, Ohio · Vol. 22, No. 1 (1998), p. 15

“My best buy is my 1997 Huskee 42-in. riding mower made by MTD. It’s equipped with a 2-cyl., 18 1/2 hp Briggs & Stratton gas engine and has seven forward speeds. The 18 1/2 hp engine allows it to cut heavy grass that’s 4 to 6 in. high with no problems, even at low speeds. Also, it’s a mulching mower so it leaves our lawn looking nice.”

Best Buy

Case-IH 9280 4-WD tractors equipped + 1 more

Wilson Gatewood, Noblesville, Ind. · Vol. 22, No. 1 (1998), p. 15

Wilson says his two Case-IH 9280 4-WD tractors equipped with 12-speed powershift transmissions are both “best buys”. “They have enough power to handle big implements such as our 42-ft. field cultivator, 10-bottom plow with 18-in. moldboards, and 7-shank V-ripper. We pull them all at 5.8 to 6.0 mph. We can cover more than 20 acres per hour with the field cultivator, and we can cover a lot of acres fast with the plow and V-ripper without using a lot of fuel.” He’s somewhat disappointed with a 60-ft. wide, 80-ft. long, 14 1/2-ft. high post frame building put up by Cleary Building Co. It’s equipped with two sets of 20-ft. wide sliding doors. “It’s a good building except that the sliding doors could be built heavier. Also, company support could be better.”

Best Buy

Ford pickups

Richard T. Wieberg, Freeburg, Mo. · Vol. 22, No. 1 (1998), p. 15

Richard likes his Ford pickups. “Several years ago I had three Fords with a combined total of more than 400,000 miles. Today I also have three Fords - a 1980 F-150 with 125,000 miles, a 1992 Escort with 110,000 miles, and a 1993 Explorer with 93,000 miles. The combined total for them is more than 325,000 miles, and none of their engines have been worked on. The F-150’s head gasket, water pump, and exhaust gasket had to be replaced. I drove it outstate several times last year. My son Kevin has two used Fords - an Escort and a Ranger - with a combined total of more than 200,000 miles. We’re shopping for a new car this year and will look only at Fords. Why change a good thing?”

Best Buy

Polaris 425 Magnum 4-wheeler atv

Edmund Drittler, Lamar, Ark. · Vol. 22, No. 1 (1998), p. 15

“One of my best buys is my Polaris 425 Magnum 4-wheeler ATV. It has instant response and handles well. I really like the automatic transmission because I never have to guess which gear I’m in. I drove other ATV models equipped with automatic transmissions, but they didn’t compare with Polaris.”

Best Buy

Lincoln AC 225 Buzz box welder

Scott Shaw, Lyman, Wyo. · Vol. 22, No. 1 (1998), p. 15

“I used a Lincoln AC 225 Buzz Box welder for more than 20 years and burned hundreds of pounds of rod with it with no problems. I recently purchased a used Ideal Arc 250 that has the versatility of AC/DC and higher amperage. If it holds up as well as the 225 it was money well spent. It could use a better amperage indicator - it sticks toward the upper and lower limits. This problem may have been corrected on newer models.”

Best BuyWorst Buy

Dessa Interna-tional + 2 more

Don Williams, Clarinda, Iowa · Vol. 22, No. 1 (1998), p. 15

“I needed parts for a discontinued brand of space heater but didn’t have any luck finding them. Finally I wrote to Dessa Interna-tional, the company that makes Reddy Heaters, and received an immediate reply listing an ‘obsolete parts’ supplier that I could contact. I was quite pleased with their prompt, informative reply and was able to fix the heater. “My worst buy is my Cover-It storage shelter which I purchased from the factory in Connecticut last year. The ends of the shelter move back and forth a lot in the wind, and I’ve had trouble keeping the top tight even though I followed the instructions exactly in erecting the shelter. I wouldn’t recommend this company’s product to anyone. Since my purchase I’ve observed that the Cover-All shelter appears to be superior, both in frame and cover.”

Worst Buy

Woods RB990 heavyduty rear blade

Rodney B.D. Ferguson, Berryville, Va. · Vol. 22, No. 1 (1998), p. 15

Rodney’s disappointed with his 1997 Woods RB990 heavyduty rear blade mower. “The first time I used it I pulled it behind an International 1486 tractor in a wet area, and both ends of the blade bent backward. The salesman came out and agreed it should never have happened. After many months went by the dealer said they had contacted the company, which said the blade was welded to the box frame in the correct way and that they would do nothing.”

Best Buy

Lincoln SP 170T 220-volt single phase

Sage Keppinger, Corvallis, Ore. · Vol. 22, No. 1 (1998), p. 15

Sage likes his 1997 Lincoln SP 170T 220-volt, single phase MIG welder. “We operate a combine repair business and are constantly welding sheet metal and thin steel plating. This welder does an excellent job on such repairs. It’s light enough that one person can carry it up into the machine to make inside repairs, yet it has enough amperage to weld 1/4-in. thick steel plate. “We operate this small MIG welder off a 13 kilowatt, 3-cyl. diesel GENSET that’s built into our service truck. For field applications like this I recommend using a large shielding device to block the wind, as the inert gas can be easily blown away from the weld. “Because we use this welder on our service truck we’ve had problems with vibration and dust. To solve the vibration problem we constructed two foam wedges to contain the wire on the wire spool and keep it from ‘rat nesting’ while traveling in the field. To solve the dust problem we replaced the wire feed conduit/gas hose with an aftermarket Teflon-lined unit, which feeds the wire more easily. The manufacturer could have offered these items as optional equipment. We’ve also had problems with the amperage control. If this control was a full range rheostat instead of a 5-position switch we could use the full range of amperage, which would allow for finer tuning and higher quality welds.”

Best Buy

Allis-Chalmers D17

Gordon C. Kien, Glenella, Manitoba · Vol. 22, No. 1 (1998), p. 15

“One of my best buys is my 1967 Allis-Chalmers D17 series 3 tractor equipped with an Allis-Chalmers 417 front-end loader that we bought in 1977 at an auction sale. We use it mostly to haul bales for 100 head of cattle and also to haul bales off the field in the fall. The engine has been overhauled only once.”

Best Buy

John Deere 4450 MFWD tractor equipped

Gordon Vallier, Valli-Vu Dairy, Peetz, Colo. · Vol. 22, No. 1 (1998), p. 15

Gordon owns a Deere 4450 MFWD tractor equipped with a powershift transmission and a 1996 Deere 6200 MFWD tractor equipped with a shuttle shift transmission and 640 front-end loader. “Both tractors are quiet and easy to operate and have a lot of power. I like the shuttle shift transmission on the 6200 - it saves time and energy when packing silage and hauling manure.”

Best Buy

Case-IH 1660 axial-flow rotary combine

Russ Coufal, Scotia, Neb. · Vol. 22, No. 1 (1998), p. 15

“My Case-IH 1660 Axial-Flow rotary combine does a great job and is easy to adjust and operate. We’ve used it for about 1,500 hours without having to replace any major parts. It’s easy to maintain and to work on, and switching from one crop to another is a simple job. I’d never go back to a conventional combine.”

Best BuyWorst Buy

Land Pride rotary mower + 1 more

Robert L. Kuhlmeier, Salina, Kan. · Vol. 22, No. 1 (1998), p. 15

“My Land Pride 72-in. rotary mower does an excellent job on short or tall weeds and on grass. However, it could be built a little heavier.” On the negative side, he lists a 1988 Ford 5900 tractor purchased by his father. “At 1,100 hours the radiator cracked on top. Poor wiring caused the lights to go on and off intermittently. At 1,265 hours the fuel injector pump developed an internal leak which cost $400 to repair. Fifty hours later it’s leaking again. The tractor is well designed and it runs and handles well. However, it has had too many small problems.”

Best BuyWorst Buy

John Deere 930 disc mower conditioner + 1 more

James A. Smith, Yale, Mich. · Vol. 22, No. 1 (1998), p. 15

“My best buy is my 1996 Deere 930 disc mower conditioner. It does a great job at high speed and has excellent flotation. It’s also easy to adjust. “My worst buy is my 1997 Orkel GP 1202 silage baler. I was told that it could be used to bale both dry and wet hay but it has failed to do so. The company has refused warranty and technical support. This baler is very limited in its use at best. Like other owners have said to me, ‘Use it one day and work on it for two’”.

Best Buy

Deines KT 2000 Magnum hydrostatic finishing mower

Robert C. Huff, Edmonton, Alberta · Vol. 22, No. 1 (1998), p. 15

He likes his 1997 Deines KT 2000 Magnum 72-in. hydrostatic finishing mower that’s powered by a 20 hp Kohler 2-cyl. gas engine. “It’s easy to use and built well. It has a zero turning radius and the deck can be raised 90 degrees for cleaning or storage. This is the second one I’ve owned. I don’t know why anyone would want anything else.”

Best Buy

Linde welder + 1 more

Luther Roecks, Worley, Idaho · Vol. 22, No. 1 (1998), p. 15

Luther likes his Linde welder which has a heavy duty wire pusher. “We’ve used it for hundreds of hours with few problems. It’s dependable and stable. “My Migmaster 250 welder has the welding wire enclosed in the welder and out of the shop dust, but it’s more difficult to put the wire inside. Enclosing the wire is a good idea. I also like the controls because they’re easy to set.”

Best Buy

Schaffert Rebounders

Allan Brooks, Markesan, Wis. · Vol. 22, No. 1 (1998), p. 15

Last June Allan mounted Schaffert Rebounders on his new Great Plains 2410 drill (Schaffert Mfg. Co., Rt. 1, Box 157, Indianola, Neb. 69034 ph 800 382-2607). The devices fasten to the seed tube and acts as a cover over the seed trench to eliminate seed bounce, while

(Continued on next page) promoting uniform depth and spacing. Fits Deere, Kinze, White, Yetter, Case-IH, and Monosem planters and most no-till and conventional drills. “I used the drill to no-till double-crop soybeans after peas and got a fine, uniform stand. I also used it to no-till winter wheat after snap beans, with equally good results. It’s really fun to dig for wheat seed behind a drill and find the seed where it’s supposed to be. Looking at a picture-perfect no-till wheat stand is surely one of the great pleasures of farming. When I compare my drill’s performance to other ones of the same make in my area, it’s evident that the Rebounders have raised my drill to a new level of efficiency.”

Best BuyWorst Buy

John Deere 7400 tractor + 1 more

Larry A. Bauman, Connell, Wash. · Vol. 22, No. 1 (1998), p. 16

Larry likes his 1995 Deere 7400 tractor and 1997Deere 7810 MFWD tractor. “Both tractors have convenient controls and good engines and 3-pt. hitch controls.” On the “worst buy” side, he lists his 1995 Ford F-150 2-WD pickup equipped with a 300 cu. in. 6-cyl. engine and 5-speed transmission. “We’ve owned many Ford pickups over the years and liked them. The problem with this one is that it has a new-design clutch slave cylinder - we’ve had to replace it twice in only 40,000 miles. Now it’s not working again but the company won’t do anything about it. They say the problem is due to our dusty conditions. It was a bad design change on a part that had worked well for many years.”

Best BuyWorst Buy

Honda 4-wheeler Foreman 400 atv + 1 more

Paul Williams, Fort Jones, Calif. · Vol. 22, No. 1 (1998), p. 16

Paul nominates his 1996 Honda 4-wheeler “Foreman 400” ATV as his “best buy”. “This machine’s reliability is unquestionable. It always runs like a top no matter what the circumstances. I use it every day and think that with proper maintenance it’ll last 10 to 15 years. We’re still using two other Honda ‘Big Red’ 3-wheeler ATV’s that are about 10 years old. “My Polaris ‘Trailboss 250’ ATV is my worst buy. Replacement parts for it are too expensive, if they’re available at all. The transmission ‘freewheels’ when the machine is going downhill, and the machine is too tall. Our Honda Foreman 400 has two or three times as many miles as the Polaris with absolutely no problems.”

Best Buy

John Deere Gator 4

Ben Barton, Mart, Texas · Vol. 22, No. 1 (1998), p. 16

“My best buy is my 1996 Deere Gator 4 by 2 equipped with a gas engine. This is an absolutely amazing, very efficient and, so far, completely dependable piece of equipment. My wife and I have a small cattle operation in the Blacklands of Texas, and during the rainy season the Gator will float over the black, sticky mud without making deep ruts. I use the Gator for all cattle management tasks including daily inspection, feeding, roundup, and fence repair. I don’t even own a horse. My wife loves it for making her daily runs with her dogs. No problems.”

Best BuyWorst Buy

Ford F-150 pickup + 1 more

Willard Donahey, Utica, Ohio · Vol. 22, No. 1 (1998), p. 16

Willard’s disappointed with his 1994 Ford F-150 pickup. “I had problems with the computer sensor which caused the engine to idle too fast. Also, the rear end is geared too high. Get rid of the computers and sensors and it would be a good truck. I finally ended up selling it. However, my old 1978 Ford F-250 4-WD pickup is still going strong at 165,000 miles. “I like Wheelhorse lawn equipment.”

Best Buy

Ford F-250 heavy duty pickup

Joe C. Drake, Encampment, Wyo. · Vol. 22, No. 1 (1998), p. 16

“I’m impressed with my 1994 Ford F-250 heavy duty pickup equipped with a 460 cu. in. engine. A rear wheel seal went out when it was still under warranty, but the dealer replaced both rear seals and installed new brake linings at no cost. That’s been the only repair after 80,000 miles, a great deal of which were spent pulling trailers. “My Harbor Freight small bench drill press is my worst buy. It’s underpowered and came apart. First the belt guard broke, then the gauge broke and a bolt stripped in the table.”

Best Buy

Husky 257 chain saw

Levi Adams, Locke, N.Y. · Vol. 22, No. 1 (1998), p. 16

“I’ve owned many chain saws over the years, but for the money none were as peppy or powerful as this one,” says Levi about his 1997 Husky 257 chain saw. “It’s lightweight, dependable, starts easily, and has a user-friendly blade brake. All controls are within easy reach. It cost less than a comparable Stihl model, but I feel that it’s built with equal quality.”

Best Buy

Miller Millermatic 130 welder

Gary Kuechenmeister, Melvin, Mich. · Vol. 22, No. 1 (1998), p. 16

Gary likes his Miller Millermatic 130 welder, a 115-volt, wire feed demonstration model that he bought in 1995. “It’s a top brand name that weighs a hefty 73 lbs. and has a cast aluminum drive system rather than the plastic kind and a built-in gas solenoid valve. I bought this welder to do jobs between my arc welder and acetylene torch outfit. So far I’ve used it only with a flux cored wire so I can’t weld thin sheet steel without burning through it. I plan to install a gas conversion kit and use solid wire and try this for welding thin sheet metal.”

Worst Buy

Agco White 6700 planter

Larry Dahlsad, Georgetown, Minn. · Vol. 22, No. 1 (1998), p. 16

“My worst buy is my Agco White 6700 planter. It doesn’t space the seeds uniformly. They drop in gobs. No one at the dealer or the company knows why this planter doesn’t work and no one will take the time to investigate.”

Best BuyWorst Buy

Miller Blue Star 2E portable + 3 more

Gregory L. Reif, Claflin, Kan. · Vol. 22, No. 1 (1998), p. 16

Gregory builds custom iron corrals and pens for farmers, ranchers, veterinarians, etc, and says his Miller Blue Star 2E portable DC welder is his “best buy”. “For three years during the fall and winter months I’ve used it 6 to 8 hours straight every day. It reminds me of a Timex watch - it just keeps on going. I’d buy another one. “I also like my Accu-Strike welding helmet with chin-activated lens. “My worst buy is my 1982 Case 2290 tractor. “The transmission never shifted properly. The tractor went through two rear ends in 1,800 hours even though I never over-pulled the tractor. After spending almost $11,000 on repairs I finally gave up on it. I replaced it with a Case-IH 7130 Magnum which is 10 times the tractor in every way.”

Best BuyWorst Buy

Agco Allis 9690 tractor + 1 more

Chop Gibson, Scranton, Iowa · Vol. 22, No. 1 (1998), p. 16

A 1994 Agco Allis 9690 tractor with an air-cooled Deutz engine and 18-speed powershift transmission rates as Chop’s “best buy”. “It starts good, has a lot of power, and is built tough. “My worst buy is my White 273 24-ft. disk. It does a good job and I like everything about it except for the gang bearings. The disk seems to eat one for lunch almost every day.”

Best Buy

Cover-All 30

Martin Kramer, Algona, Iowa · Vol. 22, No. 1 (1998), p. 16

“My best buys are my two Cover-All 30 by 72-ft. hoop buildings which I use for finishing hogs. The first one was put up in the fall of 1995 and the second one in 1996. My two sons and I built both of them and found that they’re easy to erect. They cost only about one third as much to build as a conventional hog confinement finishing building. It’s a joy to raise hogs in them. They don’t smell like a confinement building and there’s no snow to scoop as with outdoor feeding floors.”

Best BuyWorst Buy

Ram 2500 4-WD pickup equipped + 1 more

Lon Stretesky, Big Springs, Neb. · Vol. 22, No. 1 (1998), p. 16

A 1996 Dodge Ram 2500 4-WD pickup equipped with a V-10 gas engine rates as Lon’s “best buy”. “It has a comfortable ride and I’ve had very few problems with it. The transmission had to be adjusted but the dealer took care of it right away. The V-10 engine has a lot of power. It gets 9 mpg when pulling a load and up to 14 mpg on the highway, which I don’t think is too bad.” On the “worst buy” side he lists his 1996 Sunflower disk. “The person who set it up didn’t grease the bearing in the walking beam axle for the carrier wheels. As a result, the bearing went out and ruined the walking beam and shaft. We were fortunate that our dealer fixed the problem at no cost.”

Best Buy

Westmore silo blower

John H. Valentine, Carlise, Ma. · Vol. 22, No. 1 (1998), p. 16

“My best buy is my Westmore silo blower which is propane powered by a 240 hp Chrysler industrial engine. It rechops silage twice. We’ve never had a plugged silo pipe since we started using it.”

Best Buy

John Deere tractors + 1 more

Ralph Decker, Delton, Mich. · Vol. 22, No. 1 (1998), p. 16

“I’ve owned several Deere tractors over the years, but my 1995 7400 MFWD model is the best yet,” says Ralph. “It has tremendous lugging power and the Power Quad transmission is excellent. It also has a great cab and controls. It’s an excellent tractor. “My 1995 Dodge 3500 dually pickup equipped with a diesel engine has a lot of pulling power and is easy on fuel. The new-style Dodge pickups are comfortable to operate and a pleasure to drive.”

Best Buy

Hesston 4800 big square baler + 2 more

James E. Whitehead, Bennett, Colo. · Vol. 22, No. 1 (1998), p. 16

“My Hesston 4800 big square baler does a great job and needs only routine maintenance. I haven’t had to replace many parts on it. It’s a good machine. “My Lightening B bale monitor was a joke. It never worked right. “The 454 cu. in. engine on my 1989 Chevrolet pickup overheated all the time and I couldn’t get anyone to do anything about it. I can’t use it to pull anything even when the temperature is only in the 70’s or 80’s.”

Best Buy

Ford GT95 tractor

Donald L. Bradbury, Cassville, N.Y. · Vol. 22, No. 1 (1998), p. 16

Donald’s “best buy” is his 1994 Ford GT95 tractor. “I use a 48-in. mower deck with it to cut my 1 1/2 acre lawn and it does a good job. I also use a 42-in. snowblower with it which also does a good job. The snowblower has hydraulic controls and a hydrostatic transmission with high and low range.”

Best BuyWorst Buy

Kawasaki 2510 Mule + 1 more

Harry G. Walker, N. Brookfield, N.Y. · Vol. 22, No. 1 (1998), p. 16

“It’s a pleasure to drive and use,” says Harry about his 1996 Kawasaki 2510 Mule. “It has manual steering, hydraulic brakes, 2 or 4-wheel drive, a transmission with high and low range, and a locking differential. It has a lot of power, is stable on side hills, and can handle heavy loads. It steers well whether it’s empty or loaded. No problems.” On the “worst buy” side, he lists his 1993 Mountain Lion 6-WD ATV. “It’s supposed to have power steering, but when you go down a steep, rough hill at slow speeds it doesn’t work. Another problem was that when the vehicle is loaded it’s almost impossible to make a left turn. It’s easy to make a right turn because you can disengage the right drive clutch. The machine is very noisy and unpleasant to drive. It has three separate chain-driven clutches, and the chains are so tight that the bearings went out. The master links on the chains were welded on and I couldn’t find replacement links anywhere except at the factory. One clutch broke and the company replaced it - there were no dealers in my area. The man who delivered the machine said that five years from now I’d be able to tell people that I had no trouble with the machine. However, I had trouble with it after only six months - and the machine was snowed in for four of those months.”

Best Buy

DeWalt 945 12-volt cordless drill + 2 more

Robert Ingram, McArthur, Calif. · Vol. 22, No. 1 (1998), p. 16

“One of my best buys ever is my DeWalt 945 12-volt cordless drill. I’ve put a lot of hours on it. I purchased a second battery so that I can always keep it going. It’s durable and definitely built for the long haul. “My Black & Decker industrial 1/2-in. electric impact wrench is a best buy. It saves a tremendous amount of time and effort in repairing machinery. “We’re well pleased with our 1988 Honda TRX 200 SX 4-wheeler ATV which we bought used in 1990. It always starts and runs flawlessly in any type of weather. It’s on its second set of tires, second seat, and second set of sprockets and chains. The engine has never had a wrench on it, and it still has the original battery. It’s been very dependable.”

Best BuyWorst Buy

Case-IH 5130 front wheel assist + 1 more

Bob Shaw, Caroline, Alberta · Vol. 22, No. 1 (1998), p. 17

Bob nominates his 1993 Case-IH 5130 front wheel assist tractor equipped with a Case-IH front-end loader as his “best buy”. “It’s easy to start in cold weather, simple to operate, and has controls that are easy to reach. It also has a lot of hydraulic capacity. I’ve put about 4,000 hours on it in only four years.” On the “worst buy” side, he lists Briggs & Stratton single cylinder gas engines. “They require three or four times as much maintenance as other brands that I use, including Honda and Tecumseh.”

Best Buy

Westfield long dia

Dale Hallett, Carstairs, Alberta · Vol. 22, No. 1 (1998), p. 17

Dale owns a Westfield 60-ft. long, 10-in. dia. auger equipped with a swing hopper and says it’s his “best buy”. “It has a lot of capacity and is easy to use. We had some problems with a leaky gearbox and with the angle drive in the hopper. Otherwise, we’re well pleased with it.”

Best Buy

Case-IH 2188 combine

Del Bates, Acme, Alberta · Vol. 22, No. 1 (1998), p. 17

“We used it to harvest 2,200 acres last year with no problems,” reports Del, satisfied with his 1996 Case-IH 2188 combine. “It has a lot of capacity and power, a nice quiet cab, and components that are easy to adjust except for the sieves.”

Best Buy

Massey Ferguson 3075 front wheel assist

Walter Charbonneau, Chatham, Ontario · Vol. 22, No. 1 (1998), p. 17

Walter’s the satisfied owner of a 1994 Massey Ferguson 3075 front wheel assist 85 hp tractor. “I put 700 hours on in two years and only had trouble with one small electrical connection. This tractor has excellent torque down to 1,200 rpm’s and is easy on fuel, especially with the 2-speed pto which provides full pto rpm’s at only 1,500 engine rpm’s and works great for doing light work. I think every tractor should have this feature. I needed more power so I traded it in this year for a 1996 Massey Ferguson 6180 front wheel assist tractor with 110 horsepower.”

Best Buy

Flexi-Coil 1720 air cart

Mark Dallmann, Lake Lillian, Minn. · Vol. 22, No. 1 (1998), p. 17

Mark likes his 1995 Flexi-Coil 1720 air cart. “I used it to apply 575 lbs. of deep banded fertilizer per acre at 5 mph and didn’t have any problems with it plugging up. I also used it to plant soybeans at 65 lbs. per acre and it produced a nice, even stand. All I’ve had to replace was one monitor sender.”

Best Buy

Belarus 700

Bill Crawford, Winnsboro, Texas · Vol. 22, No. 1 (1998), p. 17

Bill likes his 1988 Belarus 700 series and 1994 Belarus 800 series tractors. “Both tractors have served me dependably with little down time. I really like the technical assistance provided by the company. They’re very knowledgeable and will stay with you for as long as you need them.” On the “worst buy” side, he’s had problems with the paint peeling on his 1993 Ford F-150 pickup. “The exterior paint peels down to the primer coat with even the slightest bang and under normal use. The company claims this isn’t abnormal. However, I like the pickup mechanically, and it rides nicer than many passenger cars.”

Best Buy

John Deere 980 26 1/2-ft field cultivator equipped + 1 more

Richard Siems, Melvin, Ill. · Vol. 22, No. 1 (1998), p. 17

“My 1995 Deere 980 26 1/2-ft. field cultivator equipped with C shanks does an excellent job in heavy residue. It doesn’t bounce up and down like my old Deere 1010 model did. I just turn the crank to set the depth and it stays put. One problem is that the outrigger wheels create a hole when turning at the end of the field. They should be in line with the center wheels. “My 1996 Dodge 3/4-ton 4-WD pickup equipped with a V-10 engine and 5-speed transmission is a best buy. The V-10 engine has awesome power and gets 13 1/2 mpg to 14 mpg on the highway. The pickup has an excellent ride and handles great. It’s equipped with a 4:10 rear end so it’ll easily pull a 500 bu. load. Also, it’s easy to service. One problem is that it should have a sixth gear for better fuel economy on the highway. Another problem is that the battery ran down after the pickup sat idle for only eight days. The driver is supposed to receive a warning if he accidentally leaves the headlights on. However, it only works if you take the key out of the ignition.”

Best BuyWorst Buy

Case-IH 5220 4-WD model equipped + 2 more

Vincent Malnati, Walpole, N.H. · Vol. 22, No. 1 (1998), p. 17

“It’s an excellent all-around tractor for loader work,” says Vincent about his 1996 Case-IH 5220 4-WD model equipped with an Alo Quicke 640 front-end loader. “It has a lot of traction, a 4-cyl. engine that’s very responsive, and controls that are easy to reach. I especially like the power shift reverser. The loader sits tight against the tractor which makes it easy to maneuver, even in close quarters. “My 1995 Alfa-Laval vacuum pump is my worst buy. After it was installed the pump bearings seized, the motor failed to start several times, and the rotor wings had to be replaced - all sources of much frustration when the cows are waiting to be milked and it doesn’t work. The dealer has been back at least twice to fix oil leaks in the pump housing and in the line going to the oil reclaimer. However, less than eight months after their latest attempt to correct the problem it was leaking again. It’s very disappointing to think of the dollars we spent hoping for an improvement in reliability only to find we took a step backward.”

Best BuyWorst Buy

New Holland 660 round baler + 2 more

James Hulm, Timber Lake, S. Dak. · Vol. 22, No. 1 (1998), p. 17

“My best buy is my 1992 New Holland 660 round baler. It makes a good, tight bale. We’ve used it to make more than 6,000 bales with very few repairs. “My 1989 Polaris 4-WD ATV is a best buy. I use it hard almost every day and it just keeps on going. “My worst buy is my 1988 Du-Al 305 front-end loader. The seals on the hydraulic cylinders keep blowing out. Another problem is that the lift cylinder rams are hollow with a thread-in pin end that’s made from cast iron. We’ve had to replace the one on the left side five times in the last two years. The company says there isn’t a problem.”

Best Buy

Taylor T-750 outside hot water

Eric Wallis, Rudyard, Mich. · Vol. 22, No. 1 (1998), p. 17

Eric owns a “best buy” Taylor T-750 outside hot water furnace. “I’ve used it to heat our large old farm house and the domestic water in it for the past three years. We’ve had some long, cold winters but my family and I have never been warmer and we’ve never run out of hot water. Last year I burned old fence posts most of the time but still got 12-hour burn times.”

Best Buy

John Deere 8570 tractor + 1 more

Kenneth LaHaye, Ville Platte, La. · Vol. 22, No. 1 (1998), p. 17

“My 1994 Deere 8570 tractor and Deere 7400 MFWD tractor are both best buys. The 8570 is the most comfortable tractor I’ve ever operated. It’s rated at 250 hp but seems to have even more power than that. The 7400 is comfortable and handles nice, and it has a lot of power and great hydraulics. It’s the ultimate utility tractor. “MyMiller Matic 250 Mig welder works good and makes me look like a professional welder.”

Worst Buy

Honda Fourtrax 4-wheeler ATV + 1 more

Carson Hobbs, Deloraine, Manitoba · Vol. 22, No. 1 (1998), p. 17

“My 1995 Honda Fourtrax 4-wheeler ATV just keeps on running without requiring any maintenance. “My 1995 Ford 7840 front wheel assist tractor equipped with a 7413 front-end loader is my worst buy. The loader has been a headache since day one. All the hydraulic hoses ruptured and had to be replaced. The joystick and control valves never work properly, and the transmission isn’t designed to work in our cold winters. There have been numerous other problems. It’s poorly designed and is a $90,000 piece of junk. The only good thing is that dealer has been great.”

Best Buy

DR 6 hp

Darrel Brandenburg, Brethren, Mich. · Vol. 22, No. 1 (1998), p. 17

“I like my DR 6 hp Vector ‘Pro’ electric start trimmer/mower (Country Home Products, Ferry Road, Box 89, Charlotte, Vt. 05445). The electric start feature is worth the extra cost. I don’t see why other small mowers on tillers don’t have it. The battery to start it isn’t much bigger than a box of jello mix.”

Best Buy

Ford F-150 XLT Lariat 4-wd pickup heads + 1 more

Ernest A. Sjuts, Urbana, Ill. · Vol. 22, No. 1 (1998), p. 17

A 1995 Ford F-150 XLT Lariat 4-WD pickup heads Ernest’s “best buy” list. “It looks good and is built with quality. It has a great paint job, drives good, and performs well for having a 302 cu. in. electronic fuel injected engine. It gets 14 to 16 mpg around home and 18 to 19 mpg on the highway. “My 1996 Deere 425 all-wheel-steer riding mower equipped with a 60-in. deck is the best mower I’ve ever owned. It gets around just as fast as a zero turn mower but rides much smoother.”