Real farmers rate what they bought, from FARM SHOW MagazineSubscribe  ·  Free issue  ·  Send us your Best or Worst Buy
Subscribe to FARM SHOW
Home › Issues › Vol. 23, No. 6 (1999)

Best & Worst Buys: FARM SHOW Vol. 23, No. 6 (1999)

52 reports from pages 14–16 · 47 Best Buys15 Worst Buys · See everything in this issue at FARM SHOW →

Worst Buy

AGCO tractors

Charles and Roy Grona, Amarillo, Texas · Vol. 23, No. 6 (1999), p. 14

“Our worst buys are two 1999 AGCO tractors – an 8765 model and a 9745. The 8765 has been in the shop five times for transmission problems. The transmission oil overheated and melted the plugs out of it. The plugs were made of plastic and there’s no transmission temperature warning light. The dashboard ‘sweats’ so that moisture gets into the tachometer and ground speed indicator. The dashboard was replaced but two hours later the same thing happened again. The factory says there’s no way to solve the problem. The transmission seals leak so bad we have to add of transmission oil every day.

“The 9745 model has been in the shop so many times that we’ve stopped counting. None of the gauges work, and everything is made out of plastic which breaks easily. The tractor is rated at 145 horsepower, but it doesn’t have enough power to pull an 18-ft. plow without overheating. The radiator is too small and isn’t accessible for cleaning. The pto went out and the pto engagement, which is made of plastic, wore out after 250 hours. They managed to put a sun roof on this tractor, but they didn’t think to put a cup holder inside the cab.

“We’ve owned several Deutz and Allis-Chalmers tractors equipped with air-cooled engines and they were all best buys. However, the new AGCO tractors are equipped with water-cooled engines and just aren’t as good. In our opinion, both of these tractors should be sent back to the factory as examples of how not to build tractors.”

Best BuyWorst Buy

New Holland 644 round baler + 1 more

D. Matheson, Embro, Ontario · Vol. 23, No. 6 (1999), p. 14

He likes his 1998 New Holland 644 round baler. “It’s very reliable and does an excellent job making tight, well-formed bales. We’ve used it to make 2,500 bales of hay, straw, hemp, bean straw, and corn stalks with no problems. We wish we had bought it years ago.”

On the “worst buy” side, he lists his Ford New Holland 8770 Genesis tractor. “We bought it less than four years ago to replace an older White 155 tractor and expected it to run reliably for many years. But right from the start it was plagued with breakdowns, most of them minor. Then the fuel pump began malfunctioning. It took several trips to the local dealer to get it repaired. The initial repairs were covered by the 3-year warranty. We could have extended the warranty but we didn’t because the tractor had only 1,750 hours on it and we thought all the bugs had been worked out. Unfortunately, they hadn’t. Six months later the engine blew a piston even though we had always serviced it regularly. The company wouldn’t stand behind its product and pay for an obviously defective engine. We paid a lot of money for a tractor that should have lasted many more years before needing any repairs of this sort. We’re very disappointed with this tractor and with the company for not backing up its product. We’ll never buy another New Holland tractor again.”

Best BuyWorst Buy

Red Wing boots + 1 more

Larry W. Freeman, Newalla, Okla. · Vol. 23, No. 6 (1999), p. 14

“While reading the last issue of FARM SHOW I noticed that John Landreth of Durant, Okla., is disappointed with his Red Wing boots. I, too, have a pair of Red Wing shoes that I purchased at a cost of $130 last year. The leather cracked open after only three months, the soles came off after six months, and the heels came off a month later. I contacted the company but got the runaround for so long that I no longer even want to deal with them. I’m finding out there are lots of others in my area who have had the same experience. I’m sorry there are others who will have to find out about these shoes the hard way as Mr. Landreth and I have.

“Mr. Landreth also mentioned that his best buy was a T-Post Puller manufactured by U.S. Lever Mfg. from Newalla, Okla. He stated that the company was no longer in business. I’m the president and CEO of U.S. Lever Mfg. and we are still in business. However, we now build our products under a different name for several distributors in the U.S. You can buy our post puller at local farm and ranch stores or just write me and I’ll send him one of the original T-Post Pullers for $60, which includes shipping and handling (21401 S.E. 59th St., Newalla, Okla. 74857).

“I now lease out my farm but I still hang around my farm friends. We all read FARM SHOW and pretend we’re still the biggest farmers in the state. Your magazine has such good articles on how to build things for the farm that I wish I did still farm.”

Best Buy

Volkswagen pickup equipped

Meredith Ewing, Spencerville, Ohio · Vol. 23, No. 6 (1999), p. 14

“My best buy is my 1982 Volkswagen pickup equipped with a diesel engine. It had more than 520,000 miles on it when I recently retired it. I bought it used in 1990 with about 100,000 miles on it. The company made this pickup only from 1981 to 1983. It looks like a VW Rabbit with a truck bed on back. I used it for my job which is delivering mail so I did a lot of stop-and-go driving with it. I really drove it hard but it took every bit of it. The biggest repair I ever made was to install a new head at 320,000 miles. It also went through a new generator, oil seals, timing belts, etc., and quite a few sets of tires. It got 40 to 42 mpg which really paid off.

“When I bought the pickup it had been undercoated and they really put good paint on this pickup – the tan color has held up very well. I did sand the rocker panels and repaint them every two years due to stones chipping the panels.

“I finally stopped driving it after the engine lost so much compression that it wouldn’t start on its own. I had to push it to get started. My son is now using it for parts. I’ll probably never own a pickup as good as this one again.”

Worst Buy

MacDon 9300 swather equipped

Stefan Bjornson, Riverton, Manitoba · Vol. 23, No. 6 (1999), p. 14

“Last fall I purchased a MacDon 9300 swather equipped with a model 972 25-ft. header. It’s my worst buy. After only four hours it already had four broken guards and six broken sickle sections. At 10 hours I noticed that the drive belt on the wobble box was severely cracked. I complained to the dealer and he said the cracks didn’t matter. Wrong. I had to pay for a new belt. At 11 hours the pickup reel fell apart. I called the dealer and asked him to send someone out to fix it, but I ended up having to fix it myself. At 25 hours I noticed there were holes in the canvasses caused by small stones that were getting inside it. At 49 hours the fuel cap broke and fell off, and part of it went into the tank. After I had broken 16 guards and countless sickle sections, the company finally did replace the knife, but none of the guards. By the time the swather had 150 hours on it I had gone through 43 guards and 75 sickle sections. At 300 hours I had gone through 75 guards and 125 sections. At 300 hours the muffler came loose and was repaired, but I had to pay for the parts and am still waiting for a muffler clamp. Also at 300 hours the reel drive motor broke off and nothing has been done about that yet.

“The header float system is totally hopeless. The company says you should adjust the suspension to a 40-lb. lift on the side, but it takes more than 500 lbs. to lift it 1 in. in the middle. The canvas speed and the reel can’t be adjusted on-the-go, and the low oil pressure light comes on whenever I lift the reel or header.

“I sometimes work all day with the air conditioner on. When you shut it off and turn on the heat all the windows fog up so bad that you can’t see out of them, which is a severe problem when you’re on a busy road. The company’s cure was to turn on the heat before you shut off the air conditioner, which does not work. The air cleaner on the engine has to be cleaned every day because the intake pipe is too low.”

Best BuyWorst Buy

Arctic Cat 454 4-wheeler ATV + 1 more

Tom Brozik, Fairfax, Minn. · Vol. 23, No. 6 (1999), p. 15

“My 1998 Arctic Cat 454 4-wheeler ATV does everything I ask of it. I use it to pick up rocks, spray crops, pull wagons and other jobs. I highly recommend it.”

On the negative side, he lists his 1996 Case-IH 4800 Vibra Shank field cultivator. “Soon after I bought it the ends on the spring holders started to bend and break off. I got a call from the dealer saying that the company would replace my holders with heavier ones for $700. I declined the offer. For 35 years I had used Deere field cultivators and never had any problems like this. I guess we’re all entitled to one mistake.”

Best BuyWorst Buy

Yazoo/Kees ZT Max zero-turn riding mower + 2 more

Toby Truex, Warrensburg, Mo. · Vol. 23, No. 6 (1999), p. 15

“I like my 1999 Yazoo/Kees ZT Max zero-turn riding mower equipped with a 48-in. deck. I use it to mow almost 3/4 of an acre around my yard, shop, sheds, and fruit trees. It takes me about 45 minutes to an hour to mow this area, which is less time than it took with my MTD mower. I shopped around and looked at a lot of different models, but this one looked the best. It’s equipped with a 17 hp Kawasaki engine and has true hydrostatic drive and a 1/4-in. thick steel deck.

“My worst buy is my 1999 Sears Crafts-man 22-in. high wheel push mower equipped with a bagger-mulcher. It was awkward and cumbersome, and no matter how sharp the blade was it never did a good job on my yard. I bought it last February and used it only until last September when I traded it in for a Lawn Boy 21-in. self-propelled bagger push mower. It’s an excellent product. The rear wheels are driven by separate hydraulic drive motors, which are located inside the wheel. There’s a hydraulic pump for each wheel, and a steel reservoir holds the hydraulic fluid for each pump. The controls are easy to reach and the seat is very comfortable. It’s adjustable and has folding arm rests. There are two 5-gal. saddle tanks on each side of the mower so I can mow seven or eight large yards before I have to refuel. I found that Lawn Boys cost $3,000 to $4,000 less than Grasshopper mowers. I have almost 50 hours on it with no problems whatsoever. It’s an excellent mower.”

Best BuyWorst Buy

Ford F-150 pickup equipped + 1 more

Carlton Self, Tallapoosa, Ga. · Vol. 23, No. 6 (1999), p. 15

Carlton’s impressed with his 1998 Ford F-150 pickup equipped with a 4.2-liter 6-cyl. engine. “It has as much power as a lot of V-8 engine-powered pickups on the market. It gets unbelievable gas mileage and runs quieter than any other pickup I’ve seen.

“My Deere rotary mower is a best buy. The cutter has a heavy duty gearbox and cuts anything the tractor can get through. It has a very strong frame.

“My worst buy is my Murray riding mower. One problem is that the belt on the deck slips all the time. It has gone through about three belts a year, and in thick grass it just stops cutting. The mower’s Briggs & Stratton engine had a bad flywheel and was underpowered. The next mower I buy will be a Deere.”

Best BuyWorst Buy

John Deere 750 no-till drill + 1 more

Jeff Stevenson, Ruthven, Ontario · Vol. 23, No. 6 (1999), p. 15

“It pulls easy and does a good job of placing seed in all conditions. It’s also almost maintenance-free,” says Jeff about his Deere 750 no-till drill.

On the negative side, he’s not happy with his 1997 GM Jimmy SLE. “When we drove it off the lot the cruise control didn’t work and it was in the shop for five days before they were able to find the problem.”

Best Buy

DMC Mfg + 1 more

Mervin Anderson, Joice, Iowa · Vol. 23, No. 6 (1999), p. 15

Mervin’s “best buy” is his Calcu-Dry grain drying system from DMC Mfg. “I use it on a bin dryer with a DMC transfer system. It’s very accurate and takes all the guesswork out of drying corn. I’ve used it for two years and am well pleased with it.

“My 1985 Chevrolet Celebrity car equipped with a 2.8-liter, V-6 engine is a best buy. It has more than 300,000 miles on it but is still going strong.”

Best Buy

Ford 2500 2-WD pickup equipped

C. Martin, Charles City, Iowa · Vol. 23, No. 6 (1999), p. 15

“My 1996 Ford 2500 2-WD pickup equipped with a 351 cu. in. engine and 3:55 rear end is a real lemon. It has about 21,000 miles on it. It gets only 4 to 8 mpg pulling a 26-ft. trailer and 8 to 11 mpg without the trailer. We’ve taken it back to three different Ford dealers a total of seven times during the last two years. They all tell us there’s a problem, but no one wants to fix it. Fuel economy is so poor we can’t even afford to drive it. We’re now looking for a good Ford mechanic, or for a buyer.”

Worst Buy

Uniroyal tires

John Willenbrock, Hayden, Ala. · Vol. 23, No. 6 (1999), p. 15

John’s had trouble with Uniroyal tires. “A little over a year ago I bought four Uniroyal Tiger Paw P235 by 15 tires for my Chevrolet Suburban. On a recent trip the right rear tire separated. I took it to our Uniroyal dealer and he called the company to ask if they could make an adjustment. The tire had less than 20,000 miles on it. The company refused to make an adjustment and said that the engine was too heavy for the tires. However, these tires have a 2,028-lb. rating stamped on them. Since when does a Suburban weigh more than 4,000 lbs. per axle? Uniroyal just lost a customer.”

Best Buy

John Deere 456 silage special round

Kenneth Taber, E. Randolph, Vt. · Vol. 23, No. 6 (1999), p. 15

“It works fine with either wet or dry hay and can handle any size windrow at very high speeds,” says Kenneth, pleased with his Deere 456 “silage special” round baler. “The in-cab monitor makes it very easy to make bales. The machine hydraulically ejects the bale so I don’t have to back up. It also has unbelievable capacity.”

Best Buy

Chevrolet LUV pickup

Donald Henry Degen, Bancroft, Iowa · Vol. 23, No. 6 (1999), p. 15

“My best buy is my 1978 Chevrolet LUV pickup which I bought used ten years ago for $500. It had 100,000 miles on it when I bought it but ran like a clock. It has never failed me and starts every time. It’s very easy on fuel. The only major repair it needed was a new universal joint. Sadly, it has rusted away like all LUVs do. In fact, I can check the oil without even opening the hood; the gas filler hung in mid-air; and the fender rusted away. The floor boards were rusted so bad I could look down and see the road as I drove. I patched the floor up with sheet metal and a pop riveter. However, I’ve never had any trouble with the engine or the drive train. It now has about 200,000 miles on it and, just like an old dog, you can’t shoot it -you just let it die a natural death.”

Best BuyWorst Buy

GM S-15 pickup + 1 more

John Hill, Millington, Md. · Vol. 23, No. 6 (1999), p. 15

“It’s the best vehicle I’ve ever owned,” says John about his 1985 GM S-15 pickup which has more than 216,000 miles on it. “I’ve never replaced a front end part on it and it doesn’t cut tires like new Ford pickups do. It’s powered by a factory-installed 2.2-liter diesel engine. I park it in the same place every day on a concrete floor and there are no oil stains there at all. It doesn’t leak or burn oil. I can’t understand why the EPA doesn’t require more diesel engines in vehicles. They’re twice as fuel efficient as gas engines, and under Maryland emissions tests they’re considered non-polluting.

“My worst buy is my Coleman 7,000-watt generator which I bought a few years ago. For years it sat in my garage waiting for the time when I would really need it. Well, Hurricane Floyd came along and I really needed it. However, it ran only for about nine hours before it stopped working. I took it apart and found that the plastic cover that housed the end bearing had melted. I called the company and they said they still use this same plastic housing on their new generators. I wonder if the company’s engineers have ever had to depend on this generator the way I did.”

Best Buy

SpeeCo

Cliff Lawson, Ferryville, Wis. · Vol. 23, No. 6 (1999), p. 15

A 3-pt. Quick Hitch by SpeeCo of Golden, Colo., rates as Cliff’s “best buy”. “It lets us hook up our attachments fast and easily. The 3-pt. attachments we use include a sicklebar mower, finish mower, grader blade, and a homemade bracket with 1 7/8 and 2-in. dia. trailer ball hitches that make it easy to hook up to a conventional trailer. I can load a trailer up with my loader tractor bucket then back up to it and haul it away without needing someone to help me or having to jack up the trailer. Same goes for the attachments.”

Best BuyWorst Buy

John Deere 6200 MFWD tractor equipped

Douglas McLennan, Maxville, Ontario · Vol. 23, No. 6 (1999), p. 15

“My best buy is my Deere 6200 MFWD tractor equipped with a cab and 640SL front-end loader. I bought it used about 5 years ago. It was an early model and has had a few minor problems which my dealer took care of. The company also has made some updates on this tractor. The loader works flawlessly. I like the loader’s self-leveling feature and the quick change attachments for it. Overall, I give the tractor a ‘very good’ rating and the loader an ‘excellent’ rating.

“My worst buys are ‘look alike’ vise grips, most of which have been pure junk. From now on I’ll buy only genuine ‘Vise-Grips’. I’ve bought a few tools made in China or Taiwan that were okay, but most of them aren’t as good as the well-known brand names.”

Best Buy

Ford F-150 pickup equipped

William W. Thew, Debolt, Alberta · Vol. 23, No. 6 (1999), p. 15

William likes his 1996 Ford F-150 pickup equipped with an in-line 6-cyl. engine, automatic transmission, and 3:55 rear end. “It’s very reliable and comfortable and rides nice. It gets a little over 20 mpg during the summer which I think is reasonable. I use it to haul water to our house, mounting a 250-gal. tank in the bed. The springs, tires and frame on this pickup are all more than adequate for the job.”

Worst Buy

Troy Bilt tiller equipped

B.J. Trimmer, Centralia, Ontario · Vol. 23, No. 6 (1999), p. 15

He says his “worst buy” is his 1995 Troy Bilt tiller equipped with a 5 hp engine. “It does a good job of tilling but I got hurt using it. It happened when I walked beside the tiller and it hit a stone which caused it to jump sideways and catch my feet. I’ve been doctoring it for over three years. I’m diabetic so I heal slowly. The company makes no warning that the tiller can jump sideways like this. I called the company but they just referred me to the engineering department, which casually brushed me off.”

Best Buy

Krone 130 round baler + 1 more

Ted Birdseye, Gold Hill, Ore. · Vol. 23, No. 6 (1999), p. 15

Ted likes his 1991 Krone 130 round baler. “I bought it used five years ago with one season of use on it. I’ve used it to put up 300 tons of hay each summer and have had almost no problems. It’s chain-operated so there are no belts to wear out or stretch. This baler has turned my haying work into a one-man operation.”

On the minus side, he lists his 1989 Ford F-350 pickup equipped with a diesel engine and manual transmission. “I bought it used with 100,000 miles on it. Before I had put on 10,000 miles I had to replace the clutch, which wasn’t unexpected except for that ‘wonderful’ flywheel they designed. I also don’t like the interior. I’m a rancher. Stuff belongs on the dashboard, but on this pickup it won’t stay there – there’s no interior storage. It’s a big truck but only a man and a dog can sit in it.”

Best Buy

White 2-60 tractor

John Vanden Hoven, Monkton, Ontario · Vol. 23, No. 6 (1999), p. 16

“My best buy is my 1977 White 2-60 tractor. It was the first piece of equipment I ever bought. It now has more than 8,400 hours on it. I use it 90 percent of the time for loader work. The engine doesn’t use any oil and has never had a wrench put to it.

Best Buy

Super M tractor

Carl Tiede, Britton, Mich. · Vol. 23, No. 6 (1999), p. 16

“One of my best buys was a 1953 Super M tractor which I bought new. I farm 280 acres with it and have used it to do custom work including baling, picking corn, combining and grinding feed. I overhauled it once and still use it with a loader and do other jobs with it. I don’t know how many hours are on it but it’s a bunch. It’s never had any big problems.”

Best Buy

Jesse Machine Works

Marrie Ann Marschall, Menahga, Minn. · Vol. 23, No. 6 (1999), p. 16

“My best buy is a quick hitch for Deere loaders made by Jesse Machine Works (1733 Nord Ave., Chico, Calif. 95926 ph 530 342-4379). My sons and I read about it in FARM SHOW and decided to buy it for our Deere 148 loader. The hitch also fits Deere 145, 146, and 158 loader models. It’s makes it easy to switch from a hay fork to the bucket, etc. It attaches to your loader permanently with furnished pins. To hook up, just lift two levers and drive into the bucket pins, lift up and drive away. It lets you hook or unhook in less than a minute by yourself.”

Best Buy

Honda 250 ATV

Buck Trimble, Mt. Sterling, Ky. · Vol. 23, No. 6 (1999), p. 16

Buck owns a “best buy” 1986 Honda 250 ATV. “It’s a real farm hand. All I’ve had to work on was the brakes. I wish it had a foot-operated accelerator pedal because that would make it easier to use when spraying.”

Best Buy

Case-IH Maxxum 110 tractor equipped

Arnold D. Ross, Webber, Kan. · Vol. 23, No. 6 (1999), p. 16

“For three years I leased a Case-IH Maxxum 110 tractor equipped with front wheel assist and a Case-IH L300, self-leveling, joystick-operated front-end loader. It’s a great tractor. It’s fuel efficient and the powershift transmission works great. The cab is roomy and the driver has a good view of the implements behind him.”

Best Buy

John Deere 4430 diesel

John Fowler, Wiley, Colo. · Vol. 23, No. 6 (1999), p. 16

John’s equally happy with his 1975 Deere 4430 diesel and his Deere 3010 LP. “Except for changing the oil every 100 to 150 hours, the 3010 has had nothing done to the engine. The only thing the 4430 ever needed was an engine overhaul at 7,700 hours.”

John added a second remote hydraulic to the 3310 and built a dozer for it. He’s also now adapting it to use with a backhoe.

Best Buy

Case-IH 7240

Kennth Stukey, Plainview, Texas · Vol. 23, No. 6 (1999), p. 16

“Overall, I’m satisfied with my tractor,” says Kenneth about his 1996 Case-IH 7240. “My biggest complaint is that the view from the back of the cab is blocked by the air cleaner. Also, the windshield slopes backward at the top and allows dust to settle it. All the glass should be completely vertical so dust doesn’t settle on it.”

He moved the operator’s seat 1 1/2 in. to the right in his tractor to center it properly. “If you don’t sit in the center of the tractor, it’s difficult to drive straight down rows.”

Best Buy

Case-IH 2390

Leon A. Bell, Balko, Okla. · Vol. 23, No. 6 (1999), p. 16

Leon says his 1980 Case-IH 2390 is a powerful, smooth-running machine, but he had one big problem with it. “It caught fire due to a bad wiring design in the cab. We put out the fire and repaired it. It still runs well.”

Best Buy

John Deere 5500 equipped

Larry David, Mason, Mich. · Vol. 23, No. 6 (1999), p. 16

“It has the power and traction to pull the same equipment as our 4020 and is maneuverable as our 2030,” says Larry, well pleased with his 1998 Deere 5500 equipped with MFWD. “I have only two complaints. First, I prefer the older-style Deere hydraulic couplers with breakaway protection that can be attached under pressure. Second, it needs more toolbox space.”

Best Buy

Case 4890 needs improving

Ernest Hahl, Shandon, Calif. · Vol. 23, No. 6 (1999), p. 16

Ernest says the hood on his Case 4890 needs improving. “It’s hard to get the hood up or down on a windy day. There’s no reason the manufacturer couldn’t install an electric or hydraulic lift system on the hood to make servicing it easier.”

Otherwise, he says he’s reasonably well satisfied with the tractor. “It has plenty of power and good hydraulics.”

Worst Buy

Case-IH 666

Martin DeKlotz, Filer, Idaho · Vol. 23, No. 6 (1999), p. 16

“I considered it a ‘worst buy’ when I first got it,” says Martin about his 1976 Case-IH 666. “I had problems right away with engine cavitation and the rear end came apart, all before 2,000 hours. Fortunately, I’ve had very little trouble with it since then. It now has more than 4,500 hours on it.”

Martin also recently bought an early model 766 with interchangeable front end. “The power steering seems weak. I think you’d have trouble using a loader on it.”

Best Buy

John Deere

Larry Faber, Lloyd, Mont. · Vol. 23, No. 6 (1999), p. 16

“I plan on running them another 10,000 hours or more. So far I’ve had very few problems,” says Larry, pleased with his pair of 1983 Deere 4450’s. He lengthened the clutch springs on the tractors so they’re not so jerky when using them.

Best Buy

Case-IH 3488 Hydro

Barry Zellitti, Rye, Colo. · Vol. 23, No. 6 (1999), p. 16

Barry’s had good luck with his Case-IH 3488 Hydro with front wheel assist. “We have 5,550 hours on it and all we’ve ever done was replace the tires at 5,000 hours. Otherwise, all it’s needed is routine maintenance.”

Best Buy

John Deere 4430

Duane Darling, Muleshoe, Texas · Vol. 23, No. 6 (1999), p. 16

“It has nearly 10,000 hours on it and has had nothing done to the engine,” says Duane, pleased with his 1977 Deere 4430. “All we’ve done is replace one axle bearing and had the air conditioning system switched over to new coolant. It starts and runs great and uses no oil.”

Best Buy

Steiger 470

Russ Wahl, Cut Bank, Mont. · Vol. 23, No. 6 (1999), p. 16

“It’s well-designed and is easy to work on, but is a little too light,” says Russ, well satisfied with his 1983 Steiger 470. “It needs either water or steel ballast in the frame and the front of the hood could be dropped for better visibility.”

Best Buy

AGCO-Allis 8610 equipped

Robert Knott, Ellisville, Ill. · Vol. 23, No. 6 (1999), p. 16

“It’ll outpull a 45 hp larger 2-WD on a disk chisel,” says Robert about his 1994 AGCO-Allis 8610 equipped with front wheel assist and air-cooled engine. “It’s started better in subzero weather than any tractor I’ve ever owned. I like the quick response of the hydraulics and pto.” However, he says the oil filters and oil fill are hard to get at. Also, the oil drain plug is hard to remove because it’s an inset hex head, which requires using an Allen wrench.

Best Buy

Late in the spring of 1998, I received a call from a representative of

W.K. Shuler, Canton, N.C. · Vol. 23, No. 6 (1999), p. 16

“Late in the spring of 1998, I received a call from a representative of Alliance Agricultural Products in Lindenhurst, N.Y., regarding a new herbicide they had developed called TK-10. I asked it it would kill wild garlic and he assured me that it would. I agreed to try one gallon of the product and gave my Visa card to pay the $90 bill.

“It arrived shortly and I sprayed it on the wild garlic at the recommended rate. Tap water would have worked just as well.

“This past spring, Alliance called again and asked how the TK-10 had performed. When I told him what had happened, if asked if the chemical I had received was from one or two lot numbers. I had already destroyed the container and could not give that information. He said those lot numbers had not performed as they should and he promised to send replacement chemical along with a free gas grill. In two weeks, five gallons of this junk arrived which had been charged to my Visa card for a total of $399 – no grill, of course. I could not return the package because no shipping address was given. On the phone, a company representative told me he could not give me an address but that the plant manager would call. No one ever did.

“My advice to FARM SHOW readers is to have nothing to do with this company.”

Best Buy

I bought a tool for repairing tractor tie rods from Bruce Gamble (Rt 1

Dale Fulk Sanborn, Iowa · Vol. 23, No. 6 (1999), p. 16

“I bought a tool for repairing tractor tie rods from Bruce Gamble (Rt 1, Box 173, La Feria, Tex. 78559 ph 956 797-2169). It repairs the hole in the wheel casting where the tie rod fits on Deere 2955 tractors. The problem is that the outside end of the tie rod works loose, causing it to wear on the hole in the axle casting. The tie rod cannot then be tightened up because the hole is wallowed out. The normal solution is to replace the axle casting at a cost of $850 per side plus seals and labor.

“Gamble’s tool consists of a 1-in. thick steel plate that bolts onto the casting using the fender mounting holes. The plate has a bushing that fits over the hole and serves as a guide for a drill bit. You just remove the tie rod and bolt the tool in place, then use a 1/2-in. drill with a 1 1/4-in bit to drill through the bushing into the hole. Once it’s drilled out, you just press a tapered bushing inthe hole and reinsert the tie rod. It only takes about 20 min. to repair the hole on each side of the axle.

“The tool sells for around $400 and the bushings are $30 apiece. It works great.”

Best Buy

Here’s a warning to anyone with a Heston 1340 windrower

Lloyd Clark, Albia, Iowa · Vol. 23, No. 6 (1999), p. 16

“Here’s a warning to anyone with a Heston 1340 windrower. Early models were not made properly. The pto couldn’t be greased properly because the implement end of the pto was not made right. I ruined the whole pto, which had to be replaced at a cost of $2,000. The company changed the rear end of the pto on later models.

“I also own a Sitrex 12-wheel rake. On steep ground in heavy hay, one side of the rake would lay down. Terrible. I had to equip it with an extra pair of wheels to support it.”

Best Buy

John Deere 7810 tractor

Tim Rossow, Herreid, S. Dak. · Vol. 23, No. 6 (1999), p. 16

Tim nominates his Deere 7810 tractor as his “best buy”. “It has great lugging power and is easy on fuel. The lights on it are really good and could light up a football field. We had a few minor problems with this tractor at first, but the dealer promptly took care of them. Otherwise, this tractor has been trouble-free.”

Best Buy

Simplicity Legacy riding mower equipped

Avgary G. Kehias, Pana, Ill. · Vol. 23, No. 6 (1999), p. 16

“My best buy is my 1998 Simplicity Legacy riding mower equipped with a 25 hp gas engine and a 60-in. deck. I had been using a riding mower equipped with an 18 hp engine and 48-in. deck, but this one does the job a lot faster and has cut my mowing time in half. I really like how it maneuvers around all the trees in our yard. Dealer support has been outstanding. We had some problems with the engine at first so the dealer gave us a new mower to use while ours was being repaired. After it was returned, he checked back with us to be sure that we were satisfied.”

Best BuyWorst Buy

Haybuster 256 3-pt bale shredder + 2 more

Klay Sabrosky, Dunn Center, N. Dak. · Vol. 23, No. 6 (1999), p. 16

Klay’s impressed with his Haybuster 256 3-pt. bale shredder. “We bought it five years ago to use on my Dad’s ranch where we feed about 1,000 head of cattle every winter. It’s one of the best investments we’ve ever made. We shred 2,000 to 3,000 bales with it every year. Hay comes out of the machine in a windrow and the cattle lick up every bit of it with very little waste. There’s far less waste than unrolling a bale on the ground and having the cattle tromp on the hay. It also works great for putting bedding in our feedlot. When we flip the shield up straw flies out and makes a nice even layer on the ground. It has cut the amount of straw we use for bedding in half.”

On the “worst buy” side, he nominates his 1998 Leon 707 front-end loader. “The quick-tach mounting system on it is no good -there’s too much play on the bucket. The ears on the loader arms, where the bucket cylinders mount, are cracked on one side and completely broken off on the other side. The pin mounts that attach the loader to the tractor are already cracked. Our 20-year-old Westendorf loader far outperforms this one.”