Real farmers rate what they bought, from FARM SHOW MagazineSubscribe  ·  Free issue  ·  Send us your Best or Worst Buy
Subscribe to FARM SHOW
Home › Issues › Vol. 29, No. 3 (2005)

Best & Worst Buys: FARM SHOW Vol. 29, No. 3 (2005)

61 reports from pages 12–15 · 57 Best Buys18 Worst Buys · See everything in this issue at FARM SHOW →

Best Buy

StepStart foot pedal starter

Marie Blocher, Mesquite, Texas · Vol. 29, No. 3 (2005), p. 12

“After reading a story in FARM SHOW, I purchased a StepStart foot pedal starter kit for rope-start lawn mowers and installed it on my mower. (Step Start Corp., Monroeville, Ala., ph 334 356-4860; www.stepstart.com). It fits most walk-behind mowers without a rear bagger. Once attached to the mower, you start it by stepping on a pedal. The attachment requires no tools to install and no modifications to the mower or engine. It attaches to the mower handle with four adjustable clamps. The pull cord is fed through a series of pulleys which provide the leverage to easily pull the cord.

“Not many products these days come with everything needed for installation, but this one does - right down to the tie-wrap to hold the spark plug wire,” says Marie. “Such attention to detail is really appreciated by customers because it’s so rare.

“I’m sure there are other seniors, like me, who can still mow their grass if we can just get the mower started. With StepStart, I no longer have to rely on friends or neighbors to start the mower for me. Like most seniors, I want to keep doing as much as I can for myself as long as I can. I feel the exercise I get pushing my mower is essential to my good health.”

Best Buy

Ford Ranger 4-WD pickup equipped

David Hogan, Roopville, Ga. · Vol. 29, No. 3 (2005), p. 12

David’s impressed with his 1989 Ford Ranger 4-WD pickup equipped with a 2.3-liter, 4-cyl. engine. “I bought it new and have already put more than 265,000 miles on it, yet it still has the original starter, alternator and water pump. Only the clutch and air conditioner have been replaced.”

Best Buy

Minneapolis Moline standard + 1 more

Joe Stucky, Pretty Prairie, Kansas · Vol. 29, No. 3 (2005), p. 12

“During the last 50 years of farming I’ve owned two tractors that have stood out above the rest: A 1950 Minneapolis Moline standard UTS and a 1985 International Har-vester 1066, which I still have. Both tractors were sturdy, well- engineered and simple in design compared to today’s complex tractors, which are far more expensive to keep in the field.”

Best Buy

Sunflower field cultivator + 1 more

Larry Flesher, Ridgeville, Ind. · Vol. 29, No. 3 (2005), p. 12

“My Sunflower 25-ft. field cultivator is my best buy. It has a solid frame with three pin hinges on the wings, so it stays in the ground and stays level. My dad has used one for about five years and it has proven itself. I was so impressed I just bought a new one for myself.

“My 1997 Dodge 250 4-WD pickup equipped with a 360 cu. in. engine and automatic transmission is my worst buy. I bought it used with only about 34,000 miles. It looked nice on the lot and it drives and handles well, but that’s about it. During the first 2,000 miles we owned it the transmission went out, as well as the coil, starter, generator, front axle joints, and computer. In cooler weather I have to restart it about three times before it’ll keep running.”

Best BuyWorst Buy

Lincoln 125 MIG wire welder + 1 more

Mike Shilling, Charlotte, Mich. · Vol. 29, No. 3 (2005), p. 12

“My 2000 Lincoln 125 MIG wire welder is my best buy. It makes strong, clean welds that look just perfect.

“My 2002 Chevrolet 1-ton Silverado 3500 pickup is my worst buy. Both the left and right rear fenders had to be replaced during the first year with less than 15,000 miles on the pickup. The fenders are made from soybean-based plastic which tends to rot. Once they crack they can’t be repaired. A body shop replaced them at a cost of $4,400. Then a noise developed in the heater motor, and a maple leaf was found in the fan cage. It cost $5,500 to remove sheet metal from the floor of the pickup bed. The sheet metal was full of dings and dents. They might as well have used tin soup cans.”

Best BuyWorst Buy

HTP Mig 240 welder + 2 more

Harold Bevill, Blytheville, Ark. · Vol. 29, No. 3 (2005), p. 12

“My best buy is my HTP Mig 240 welder (HTP America, Inc., Arlington Heights, Ill. ph 800 872-9353). We’ve used it to build toolbars and also to repair and weld derby cars. It always performs flawlessly.”

On the “worst buy” side, he lists his C/P turbo 1/2-in. impact air wrench. “The company rates it at 800 lbs. torque, but I don’t think it’s half that. We quit using it and bought a Harbor Freight Earthquake 1/2-in. impact wrench. It has more power and cost only about one-third as much.”

Best Buy

Farmall B tractor

Joseph DeRuiter, Vesper, Wis. · Vol. 29, No. 3 (2005), p. 12

“Our best buy ever was a Farmall B tractor. My dad bought it used when I was 14 or 15 years old. I’m 54 now, so the tractor has to be 60 to 70 years old now. I use it for getting firewood and for raking hay and doing other chores. If the battery ever goes dead I just pull the choke, set the throttle, and flip the switch on. Then I take the hand crank to the front of the tractor and crank it two, three or four times at most and it will start right up. It doesn’t zero.”

Best Buy

Chevrolet Silverado pickup equipped

Morgan Reeder, Brigham City, Utah · Vol. 29, No. 3 (2005), p. 12

“My 2001 Chevrolet Silverado pickup equipped with a Duramax diesel engine and Allison automatic transmission is my best buy. It has a lot of power and is fuel efficient, making it an ideal pickup for towing trailers. The grade-braking feature is impressive, and the transmission adjusts itself to the way you drive. Also, it rides smooth without any rattles or vibrations.”

Best BuyWorst Buy

Milwaukee 1/2-in hammer drill equipped + 1 more

Lowell Patterson, Eighty-Four, Penn. · Vol. 29, No. 3 (2005), p. 12

Lowell’s “worst buy” is his Milwaukee 1/2-in. hammer drill equipped with a German-made Rohti chuck. “Even with only average use the Rohti chuck will fail. Sears, DeWalt, Bosch and others have all used this same chuck. It won’t hold tight on bits and will rapidly deteriorate in performance until it fails totally. I’ve used this chuck on several different brands of hammer drills. I wrote to several of the manufacturers but got no response.

“While working in a feed mill a few years ago, I had occasion to use a Black & Decker no. 8 nibbler to cut 12-ga. (almost 1/8-in. thick) stainless steel sheeting. Stainless steel is just about the toughest metal to cut. The tool would break after one 4 by 8-ft. sheet. I knew I had to do something to keep the owner of the mill from quitting the project. So I decided to use copper bearing anti-seize compound on the bottom side of the sheet, where I would be cutting. I used heavy gear oil to cover the cut-mark on top, so I could still see the pencil mark. With this simple change I was able to extend the life of the tool greatly. At $85 a set this was an exceptional improvement.”

Best Buy

Ford Ranger pickup + 1 more

Harley T. Green, Illen, Minn. · Vol. 29, No. 3 (2005), p. 12

“My 1992 Ford Ranger pickup, which I bought used, is fuel efficient and requires very little maintenance. It always starts and is easy to service. It’s not a big power house machine, but it gets me where I want to go. I just purchased a used 1998 model and hope to get the same service from it.

“The Lenox gas furnace we bought new in 1998 has caused us nothing but trouble. It’s extremely noisy. The dealer has been out three or four times but can’t seem to fix it. It came with a five-year warranty, but the warranty covers only one year on labor. The warranty has expired now, so it’s time to either start repairing it or replace it.”

Best Buy

Innovative Industries + 1 more

Steve LaSowski, Middle Lake, Sask. · Vol. 29, No. 3 (2005), p. 13

“I’m pleased with the 16-ft. gooseneck tandem cattle trailer I bought from Innovative Industries (Porcupine Plain, Sask., Canada ph 306 278-2975. It’s easy to pull and hook up, has good doors and latches, and a paint job that resists stone chips. Also, it has good brake control.

“My Bale King bale processor is equipped with a fine cut attachment that I really like. It does a good job of feeding and bedding livestock and is easy to hook up. It’s a low-maintenance machine.

Best BuyWorst Buy

Chevrolet Silverado pickup equipped + 1 more

James Harmon, Uncasville, Ct. · Vol. 29, No. 3 (2005), p. 13

“My worst buy was a 2000 Chevrolet Silverado pickup equipped with a 6-cyl. engine. During the first year of use this pickup was returned to the dealer five different times for an annoying problem with exhaust vibration, and twice for a starting problem in cold weather, which turned out to be a defective fuel pump. After the 3-year, 36,000-mile warranty expired, I had two more fuel pump failures, two shorted distributor caps, one shorted coil, and an internal coolant leak, all before the pickup had 45,000 miles on it. I traded it in for a Toyota Tacoma and couldn’t be happier.”

Best Buy

Allis-Chalmers 190 XT tractor + 2 more

Shauna and Brent Sereda, Thorsby, Alberta · Vol. 29, No. 3 (2005), p. 13

“My husband likes his Allis Chalmers 190 XT tractor. It was his first major tractor purchase when he started farming,” says Shauna. “This tractor is easy to shift, and the cab has good visibility. We installed speakers and a cassette-radio in the cab. It’s a nice tractor.”

A 1998 Homelite Weedeater with 17 in. of cutting capacity rates as their “worst buy”. “It worked well only for one summer. Then, even though it was stored in a dry shed, the primer bubble cracked and had to be replaced. The set screws to adjust the carburetor had plastic tops, which stripped after only a few adjustments were made. The slip clutch seized a few times even though it was kept dry. The fuel line was replaced twice as it, too, kept cracking. We’re tired of fixing this tool every time we want to use it. It was officially retired last summer by a second hand Ryobi that looks the worse for wear, but actually works. The Homelite was pampered and looks like new, but it was junk.”

Best Buy

Airlift Technologies water pumping windmill

Rachel Crowe, Skull Valley, Ariz. · Vol. 29, No. 3 (2005), p. 13

An Airlift Technologies water pumping windmill rates as Rachel’s “best buy” (Airlift Technologies, Redlands, Calif. ph 877 793-3771; www.airliftech.com). It pumps water by the use of an air injection pump. “It eliminates a lot of the expensive mechanical parts found in other water pumping windmills, which lowers the cost of maintenance.

“The windmill is capable of pumping up to 30 gallons per minute and can be located up to a quarter mile away or wherever the wind reaches maximum velocity such as on a nearby hill. It doesn’t have to stand over the water source. All moving parts in the system are above ground. There are no cylinders, leathers or plunger-type assemblies as in other water pumping systems. It can be installed by one person in less than a day.

“It aerates the water as it pumps, so we don’t need to use chemicals in our 2,000-gal. storage tank. Another advantage is that it’s designed to tolerate wind gusts up to 80 mph.”

Best Buy

John Deere 4010 tractor + 1 more

James McLaughlin, Mannville, Alberta · Vol. 29, No. 3 (2005), p. 13

“My 1962 Deere 4010 tractor has been more or less totally rebuilt over the years but is still a great tractor. It’s my best buy of all time.”

James is a dealer for Star Choice satellite TV systems which he says is a “best buy.” “I’ve had problems with less than 5 percent of all the systems I’ve installed. Being a dealer is a rewarding and enjoyable way to supplement my income.”

Worst Buy

Maytag Performa automatic dishwasher

Mike Appec, Pipestone, Minn. · Vol. 29, No. 3 (2005), p. 13

“ O u r Maytag Performa automatic dishwasher is our worst buy. The main pump water seal has been replaced twice, and the door seal started leaking right after we bought it. This machine seems to make more noise as it gets older. Also, we have to pre-rinse our plates and pans so it will clean them.”

Best Buy

Ford F-150 4-WD Supercab pickup equipped

Gary Max Busler, Blaine, Tenn. · Vol. 29, No. 3 (2005), p. 13

“Last August we bought a used 1999 Ford F-150 4-WD Supercab pickup equipped with a 5.4-liter, EFI V-8 engine and an electronic 4-speed automatic transmission with overdrive. It’s a really nice pickup and is fuel efficient, getting about 22 mpg on the highway. Unlike older Ford models, when the transmission goes into overdrive it doesn’t jerk as you go down the road. I’m really proud of this pickup.”

Best Buy

Hummer

Richard “Red” Guthrie, Brownwood, Texas · Vol. 29, No. 3 (2005), p. 13

“My 2003 H2 Hummer is a great vehicle but the warranty on it is worthless or even less than worthless, especially for a $72,600 vehicle. A lot of the problem was with the dealer, but I also personally sent two registered letters to the company chief executive officer and never even got a reply.”

Best Buy

New Holland BR 740 silage

Earl Ray Zimmerman, Ephrate, Penn. · Vol. 29, No. 3 (2005), p. 13

“My 2004 New Holland BR 740 ‘silage special’ round baler is my best buy. It makes 4 by 5 bales that weigh about 900 lbs. apiece. It bales faster than my old NH 648 model ever did. I used it last year to make about 4,500 bales. I can average 45 bales per hour with three wraps of mesh. My only complaint is that the endless belts need to be improved. I tore five of the baler’s six belts.”

Best Buy

John Deere 2210 compact tractor

Nick Hatley, Matthews, N.C. · Vol. 29, No. 3 (2005), p. 13

Nick bought a 2004 Deere 2210 compact tractor for his lawn care business and says it’s his “best buy.” “I used it one time with a brush cutter to mow down heavy brush. This tractor isn’t much bigger than a riding mower, yet it was able to mow down trees up to six inches in diameter. It pulled through mud, rocks and vines and got the job done.”

Best BuyWorst Buy

Milwaukee 14.4-volt cordless drill + 1 more

Alan Slovick, Soldiers Grove, Wis. · Vol. 29, No. 3 (2005), p. 13

Alan likes his Milwaukee 14.4-volt cordless drill. “It really came in handy when I needed to do structural work on a barn with no electricity. through 12-in. white oak timbers that were 100 years old and hard as a rock. This drill paid for itself on that job alone. Later on, I purchased the flashlight that can be used with it. The flashlight takes the same batteries. I liked it so well that after using it for a week I threw away my shop trouble light. The batteries have lasted several years and are still as good as new. It’s a wonderful tool.

“My Strait Line laser level is my worst buy. I used it one time to put up concrete forms. Later I found the level was off by 1 in. for every 10 ft., and now I have a 26-ft. local hardware store cheerfully refunded my money but I still have a crooked building.”

Best BuyWorst Buy

Decon + 1 more

Joseph S. Yonick, Shickshinny, Penn. · Vol. 29, No. 3 (2005), p. 13

“I had trouble catching mice with a regular mouse trap, although I did find that sprinkling grated Parmesan cheese over and around the trap worked better than placing a piece of cheese on the trigger. Finally I purchased an enclosed trap made by Decon, and it worked great. My mouse catch is now down to zero.

“My Suzuki 500 ATV equipped with an automatic transmission is my worst buy. I had trouble shifting it from park into all the other gears, and the dealer, who is located 30 miles away, wasn’t able to solve the problem. I wouldn’t recommend this ATV to anyone.”

Best Buy

John Deere 4040 MFWD tractor equipped

Blaine Runner, Ashby, Neb. · Vol. 29, No. 3 (2005), p. 13

“My 1978 Deere 4040 MFWD tractor equipped with a model 158 front-end loader and grapple fork is my best buy. The loader has been on the tractor ever since I bought it. I’ve used this tractor continuously for ranch work, putting up hay during the summer, and feeding hay during the winter. The engine and front axle parts both were overhauled once. The powershift transmission never wore out but the shifter lever did. The tractor now has 15,000 to 20,000 operating hours, much of them at reduced rpm’s.”

Best Buy

Stihl 021 chain saw

Warren Wing, Newkirk, Okla. · Vol. 29, No. 3 (2005), p. 13

“My 2001 Stihl 021 chain saw is my best buy. I’ve used Stihl chain saws for many years. Four years ago we had a terrible ice storm, leaving my yard full of broken tree limbs and also a lot of limbs down around edges of fields. I bought this saw to clean up the brush. It starts easy and is well-balanced and lightweight, making it easy to use. I’m sure it’ll last a long time.”

Best Buy

Case 60 XT skid steer loader + 3 more

Lynn D. Wrosch, Onaga, Kansas · Vol. 29, No. 3 (2005), p. 14

Lynn’s the owner of a 2003 Case 60 XT skid steer loader as well as a Hick hydraulic rotary tree saw that mounts on the skid loader (Hick Fabrication, Berryton, Kansas ph 785 862-8603). He says they’re both best buys. “The tree saw is easy to maintain and cuts scrub trees like crazy. The skid loader runs great and has a lot of power.

“I’m also well pleased with my Miller plasma cutter.

“We have a 1953 Farmall Super M loader tractor equipped with a live hydraulic pump that drives off the timing gear. The problem is that we were always breaking the timing gear when lifting heavy loads. To solve the problem we had a machinist cut the center out of a good timing gear, leaving about one inch of the original gear. He then machined out a solid steel hub and bolted the new hub to the original gear. We haven’t had any problems with it since.”

Best Buy

Ram 2500 equipped

Clem H. Miller, St. Anthony, N. Dak. · Vol. 29, No. 3 (2005), p. 14

“It’s the best pulling pickup I’ve ever owned,” reports Clem about his 2004 Dodge Ram 2500 equipped with a Cummins diesel engine. “I’ve used it to pull a 28-ft. high profile fifth wheel trailer. It’s really fuel efficient. It’s fun to drive this pickup with the fifth wheel attached.”

Best BuyWorst Buy

Bobcat skid steer loader + 1 more

William Hintz, Pierce, Neb. · Vol. 29, No. 3 (2005), p. 14

“My best buy ever was my 1981 Bobcat skid steer loader. I used it to load silage every day of the year and also to load all the manure from our farm. In 1998 I traded it in for a new Bobcat 773. No problems with either machine.

“The Cummins irrigation engine that I bought new in 2000 is my worst buy. It was hard to start, due to a bad starter. Then the push button starter switch kept falling off due to vibration. The exhaust pipe also vibrated off.”

Best Buy

Speeco 35-ton log splitter

Charles Trubey, Arcadia, Ind. · Vol. 29, No. 3 (2005), p. 14

“I’ve had problems with the 2003 Speeco 35-ton log splitter I bought from Tractor Supply Co. It has a big hydraulic cylinder, and when the nut holding the piston onto the shaft came loose I had to pay $80 to have it repaired at a machine shop. The splitter came with a one-year warranty, and since I had owned the machine for one year and nine months the company wouldn’t help out. I think they should have because it was a matter of poor workmanship.”

Best Buy

Jeep Wrangler

Howard Hoftyzer, Rushmore, Minn. · Vol. 29, No. 3 (2005), p. 14

“I bought my 1988 Jeep Wrangler used with 130,000 miles and now it has more than 180,000 miles. I have a towbar on it so I can tow it to other farms. It’ll go anywhere an ATV will go. It’s fuel efficient and can be driven all year long even in Minnesota’s coldest weather. I can use it to tow loads weighing up to 3-ton loads if I’m careful.”

Best Buy

Bed Slide 4

Kevin West, Covington, Ohio · Vol. 29, No. 3 (2005), p. 14

“My 2004 Bed Slide 4 by 8-ft. bed extender for pickups is my best buy (ph 888 807-0099; www.bedslide.com). I installed it in my capped work truck. It’s rated at 1,500 lbs. and evenly distributes all my carpentry tools, making them easy to reach. All but 24 in. of the unit can be extended out the back of the bed. It locks both in the open and closed positions. It also provides an area underneath for storing 2 by 4’s pipes, etc. It cost $625 shipped to my trailer dealer. I give it an A-1 rating.”

Best BuyWorst Buy

Strip Cat strip-till machine + 1 more

Bruce Reeder, Shelton, Neb. · Vol. 29, No. 3 (2005), p. 14

Bruce likes his Strip Cat strip-till machine (Twin Diamond Industries, Minden, Neb. ph 308 832-1983; www.twindiamondind.com). “It clears out corn rows and places fertilizer under the row. Wherever I used this machine my corn yielded at least 30 more bushels per acre. This company makes good products and educates people on strip-till techniques.”

On the “worst buy” side, he lists his 2000 Polaris 4-WD ATV. “The clutch broke after only about 18 months of use, and it took three weeks to get a new one.”

Best BuyWorst Buy

Stihl MS 260 + 1 more

Larry G. Sassen, Little Falls, Minn. · Vol. 29, No. 3 (2005), p. 14

“It’s the lightest, most powerful chain saw I’ve ever owned,” says Larry, pleased with his Stihl MS 260. “It always starts promptly and maintains power, even if the air cleaner gets covered with a thick coat of dust.

“My 1999 Chevrolet Ventura van is my worst buy. The service engine light is always coming on, even when the engine seems to be running smoothly. All six fuel injectors had to be replaced within the past year, even though the van has less than 70,000 miles on it. Also, the air bag light is always going on and off.”

Best Buy

Hesston 80-66 4-WD tractor equipped + 1 more

Randy Beaupre, Frankville, Ontario · Vol. 29, No. 3 (2005), p. 14

“Our 1990 Hesston 80-66 4-WD tractor equipped with an Allied 594 front-end loader is a great tractor and has been trouble-free while requiring only routine maintenance. The 4-WD really comes in handy in muddy barn yards when loading manure, feeding round bales, and doing many other jobs. My dealer stands behind this product, and if any parts are needed he always has them on hand.”

Best BuyWorst Buy

Ram ton pickup equipped + 2 more

John Graham, Southwest City, Mo. · Vol. 29, No. 3 (2005), p. 14

“It’s reliable and fuel efficient and is also comfortable to drive,” says John, pleased with his 2001 Dodge æ-ton pickup equipped with a Cummins diesel engine.

He’s disappointed with his 2002 Troy Bilt Bronco tiller. “It’s built too light and acts just like it was a real bucking bronco.

“My Troy Bilt weed whacker doesn’t maintain the height adjustment, and the electric starter failed after only two months of use.”

Best BuyWorst Buy

Trailmann 7 + 1 more

Joe Eilert, Jewell, Kansas · Vol. 29, No. 3 (2005), p. 14

“I like my 2003 Trailmann 7 by 24-ft. livestock trailer (Mann Made Products, Inc., ph 800 748-7505; www.trailmann.com). I had it custom-built, with many convenient features added to it. The company really listens to its customers. Its trailers cost a bit more than some other brands, but the extra cost is well worth it. This is my second Trailmann model.

“My worst buys were the Michelin radial tires on my new pickup. One tire blew out with only 500 miles on it. The Michelin dealer wanted $185 for a new tire after adjusting for tire wear. I already had a new spare tire so I mounted it on the pickup. Now the four tires on my pickup have 32,000 miles on them and already they’re almost worn out. I think that’s very poor performance for tires that cost $270 apiece.”

Best Buy

Ferguson T0 35 tractor + 1 more

John Rempel, Kleefeld, Manitoba · Vol. 29, No. 3 (2005), p. 14

“My 1955 Ferguson T0 35 tractor turned 50-years old last month. When I bought this tractor it was the only one I had at the time. For 20 years I used it to do all our fieldwork. Later on I used it as a second tractor. I still use it to move snow during the winter and to work in our yard and garden during the summer. In 1964 I put new Goodyear rear tires on it. The tires still don’t have any cracks and have two thirds of the original tread left. I had the tractor’s engine rebuilt 20 years ago, and it still runs like a clock. Whenever this tractor isn’t in use I keep it in a shed. It’s an excellent tractor, and I expect to use it for a long time yet.”

Best BuyWorst Buy

Mack CH 613 tri-axle dump truck + 2 more

Doug McAlexander, Cedar Grove, Tenn. · Vol. 29, No. 3 (2005), p. 14

Doug nominates his 1993 Mack CH 613 tri-axle dump truck as his “best buy.” “I bought this truck used in 1996 with about 300,000 miles on it. Now it has about 750,000 miles. I use it to haul GVW loads weighing up to 74,000 lbs. It’s powered by an E7 300 hp Mack engine, which is the most dependable engine I’ve ever owned. The engine valve cover has never been off. I removed the oil pan at about 700,000 miles and also replaced the crankshaft bearings for preventative maintenance.

“I’m not happy with my 2003 Maytag washing machine, which is a quiet series, heavy-duty model. Whenever this washer goes into the spin cycle it’s almost impossible to keep it balanced, so I have to stay right with it. When it gets out of balance, it makes loud metal-to-metal banging sounds and also slides around on the floor. I can move the clothes around, but it doesn’t take long before it gets out of balance again. I bought it at Lowes, and they said I should contact Maytag. But all Maytag wants to do is sell me an extended warranty. I was happier with the old Maytag that this one replaced.

“About two years ago I ordered a tire bead breaker from Northern Tool and Equip-ment Co. and it’s a worst buy. I’ve never been able to break a bead down with it. The tool simply slides off the rim instead of pushing the bead down. It was built in China and is made of steel that’s too soft. It cost $19.99, but it’s not worth anything to me.”

Worst Buy

Wilkening wood burning fireplace

Glenn Arfstrom, Willmar, Minn. · Vol. 29, No. 3 (2005), p. 14

“I’m disappointed with my Wilkening wood burning fireplace. The secondary combustion chamber, which consists of a brick metal rack, burned out and fell into the firebox below after a year, rendering it useless. The company refused to do anything about the problem. Their 20-year warranty didn’t even cover a 2-year-old product.”

Best Buy

Po-laris Magnum 4

John C. Haldemann, Chinook, Mt. · Vol. 29, No. 3 (2005), p. 14

“It’s one of the most useful machines on our ranch,” reports John, owner of a 2004 Po-laris Magnum 4 by 4 ATV. “It’s simple in design and fits our needs perfectly. We use it for working and checking on cattle and sheep, fixing fence, haying, and so forth. No problems.”

Best BuyWorst Buy

Ford vehicles + 1 more

Sam Rauh, Okeene, Okla. · Vol. 29, No. 3 (2005), p. 14

“Our family owns many Ford vehicles. It started with a 1986 250 diesel pickup with more than 250,000 miles on it. Then we bought a 1991 F-350 diesel pickup with more than 150,000 miles. No problems with either one. These pickups have really been put to the test. They have little to no highway miles and are usually loaded with two or three hay bales. We blower’s intake without plugging up. I’ve used it a lot, with no breakdowns.

“My worst buy was my 2003 Harbor using it to drill through some 3/8-in. iron when it started blowing pieces of white plastic out the vents. Then it flashed a big spark and shorted out, giving me a shock through the plastic handle. I had only used the drill a few times.”

Best Buy

Farmall N

Kurt F. Cordes, Burbank, Wash. · Vol. 29, No. 3 (2005), p. 15

Kurt uses his 1947 Farmall N and 1948 Farmall H tractors in his haying operation and says they’re both “best buys.” “These experienced workhorses always get the job done. I think more people should think about using fine, older tractors like this for their operations. They’ll save you money in the long run.”

Best Buy

Kubota BX 23 tractor equipped

Brian Miller, Laurens, N.Y. · Vol. 29, No. 3 (2005), p. 15

Brian’s impressed with his 2004 Kubota BX 23 tractor equipped with a front-end loader and backhoe. “I like how easy the loader and backhoe are to put on and off. This tractor far surpasses my old Kubota B-8200 model, which was equipped with a fixed 5-ft. wide, hydraulic-operated front blade. It easily handles the same implements I used with that tractor, which include a 48-in. Bush Hog, a York rake, etc.”

Best Buy

Honda Foreman 450 ATV + 1 more

Ed and Liz Ketter, Osborne, Kansas · Vol. 29, No. 3 (2005), p. 15

“My Honda Foreman 450 ATV is my best buy. It always starts and runs perfectly. I use it to spray crops, herd cattle, run errands, and so forth. I have a sprayer with a 25-gal. tank mounted on the ATV’s rear rack. It’s very stable even with a full gas tank, and it never burns or leaks oil. Also, I like the 2-WD switch.

“The non-asbestos disc brakes on my In-ternational Harvester 656 tractor always lock up in cold weather, no matter how they’re adjusted. The original brake discs lasted a long time - 6,000 hours - and they always worked.”

Best Buy

Cabela’s + 1 more

Gina Langley, Ruidoso Downs, N. Mex. · Vol. 29, No. 3 (2005), p. 15

Gina likes the Magnum game carrier he bought from Cabela’s. “It works better than a wheelbarrow and cost just $100. I use it to haul wood, feed bags, hay bales, and other loads around my rocky, hilly property. It can haul a 300-lb. load over rough terrain with ease. Comes with straps for lashing the load down.”

She nominates her Polaris 6-wheeler ATV as her “worst buy.” “It’s difficult to maneuver, and the two extra wheels have to be patched regularly. Another problem is that it doesn’t have enough power in reverse gear, and it has a tendency to roll over more frequently than 4-wheelers do. Also, the brakes can’t hold it back from hurtling down hills or rolling away whenever I think it’s parked.”

Best Buy

Chevrolet Duramax pickup equipped

Jack Kovars, Mountainburg, Ark. · Vol. 29, No. 3 (2005), p. 15

“My 2001 Chevrolet Duramax pickup equipped with an Allison 1000 and 5-speed automatic transmission is my best buy. This is the first Chevrolet product I’ve ever owned. I use it to pull a 16,000-lb. fifth wheel trailer. This pickup now has about 67,000 trouble-free miles on it. It has an excellent ride, too.”

Worst Buy

John Deere 702 cart-type 10-wheel

Bill Staton, Sheridan, Mo. · Vol. 29, No. 3 (2005), p. 15

Bill’s unhappy with his 2003 Deere 702 cart-type, 10-wheel rake. “The problem is that it can’t handle heavy hay. Instead, hay just balls up at the end of the rake. I fought with it for two seasons before I got rid of it and bought a New Holland bar rake. I find that hay bales up so much better with a bar rake than it does with a wheel rake. The company wouldn’t help at all.”

Best Buy

MTD 8 hp snowblower

Marvin Kroontje, Magnolia, Minn. · Vol. 29, No. 3 (2005), p. 15

“My 2002 MTD 8 hp, 26-in. snowblower keeps going in snow as deep as the top of the but I need more experience with this system before I can be sure.

“Before I bought this drill, I spent about two hours between fields on the road. I had to unhook the three drills, fold the hitch wings, and hook the drills together for transport. Once I got to the field, I had to hook the drills back up again. Now, moving is easy because all the lifting and folding is done hydraulically. I just get out of the tractor and flip four small levers in order to lock the drill into road transport position. I can be ready to move in less than five minutes.

“On the downside, by purchasing this drill I went from a 36-ft. seeding width to a 30-ft. width. The company only offers this type of drill in 30 and 40-ft. widths, and the wider drill would be too much for my tractor to pull.”

Best BuyWorst Buy

Great Plains 3000-3S grain drill

Robert Clausen, Fairfield, Wash. · Vol. 29, No. 3 (2005), p. 15

Robert’s impressed with his Great Plains 3000-3S grain drill. “For many years I’ve been using three International Harvester 510 drills to seed my legumes. To plant seed at the proper depth, I always had to chisel the ground during the fall and then cultivate at least twice the following spring before seeding. With this drill, I can sow legumes right into standing stubble. The drill’s offset double disc openers, combined with an adjustable, positive down pressure system, let me place seed wherever I want it without any prior cultivation.

“I’ve started using one-pass fertilizer applicators that I rent from local dealers to fertilize into standing stubble. Then I seed with the drill. So far this has worked pretty well, but I need more experience with this system before I can be sure.

“Before I bought this drill, I spent about two hours between fields on the road. I had to unhook the three drills, fold the hitch wings, and hook the drills together for transport. Once I got to the field, I had to hook the drills back up again. Now, moving is easy because all the lifting and folding is done hydraulically. I just get out of the tractor and flip four small levers in order to lock the drill into road transport position. I can be ready to move in less than five minutes.

“On the downside, by purchasing this drill I went from a 36-ft. seeding width to a 30-ft. width. The company only offers this type of drill in 30 and 40-ft. widths, and the wider drill would be too much for my tractor to pull.”

Best Buy

John Deere 4320 tractor

Leo N. Munteanu, Wood Mountain, Sask. · Vol. 29, No. 3 (2005), p. 15

A 1972 Deere 4320 tractor rates as Leo’s “best buy.” “I bought this tractor used in 1976 with 1,200 hours on it and used it for 28 years to pull a 21-ft. cultivator and 21 ft. of press drills hooked together. I also use it during the winter to feed my cows. Over the years I put two clutches in it. Now it has more than 14,000 hours on it but still runs perfect.”

Best Buy

John Deere 6030 2-WD tractor + 1 more

Joe Borgen, Stanley, N. Dak. · Vol. 29, No. 3 (2005), p. 15

“My 1975 Deere 6030 2-WD tractor has more than 8,000 hours on it with few problems and is my best buy. It has a lot of power, a good hydraulic system, and pulls great. It’s also reliable.

“My 1997 Chevrolet K1500 4-WD pickup equipped with a 350 cu. in. Vortec engine and automatic transmission was bought used with about 30,000 miles on it. The truck now has about 195,000 miles. I had to put two transmissions in it during the first 150,000 miles. However the rest of the pickup, including the engine, works good.”

Best Buy

Central Boiler Classic outdoor wood burning furnace

DeWayne Bauman, Montrose, Minn. · Vol. 29, No. 3 (2005), p. 15

“My best buy is my 1996 Central Boiler Classic outdoor wood burning furnace. After looking at all the different brands and models I decided to buy this one because it has a heavy build, a rear exit chimney, a simple design, no extra doors, flues or baffles, and spray-on foam insulation. It has been trouble-free. This furnace burns way less wood than many other brands. I liked it so much that I became a dealer.”

Best Buy

Ford New Holland bi-directional

Gary Malone, Palisade, Neb. · Vol. 29, No. 3 (2005), p. 15

“Since your report in the last issue of FARM SHOW about the problems I’ve had with my 2002 Ford New Holland bi-directional TV140 tractor (purchased in November, 2003 and already more than 35 on-farm service calls), I finally had to threaten my dealer with a lawsuit. They came out the next day and finally found problems with the fuel pump, the timing, and the fuel injectors. When they first tested the tractor, the dyno was at 60 hp. But after the repairs it was like a new tractor, with the full 105 hp. When we got it home, it was like driving a new tractor. After a year and a half of hassle, it looks like we finally have the tractor we thought we bought originally.

“But here’s the bad news. The bill for the work was $2,525. The dealer said the New Holland block man was going to pay half, ‘even though he didn’t have to’ since the tractor is now out of warranty. I had to pay my half to get the tractor back, even though I have been calling and working with them on this – and many other problems totalling thousands of dollars – ever since I bought the tractor. The only reason it’s out of warranty now is because they dithered around for so long. If they don’t have any liability, why are they paying half? I think it’s because they know they can get away

with not covering the entire amount.

“My recommendation to anyone doing business with Ford New Holland is to pay $150 to have a lawyer look over any warranty contract you sign with the company. And if you end up with a tractor or other machine with problems, don’t waste time. Get a lawyer, go down to the dealer, and get a written contract from them that the problems will be resolved. If they won’t give you that, file a lawsuit sooner rather than later.”

Best Buy

Safety Seal kits

Mark Newhall, Lakeville, Minn. · Vol. 29, No. 3 (2005), p. 15

“I’m pleased with the quality and ease of use of Safety Seal kits for repairing flat tires (www.safetyseal.com or ph 800 888-9021). You use a small metal tool to ream out the puncture hole where a tire is leaking, and then use another tool to push in a small rubber plug. There’s no drying or curing time and you don’t use any messy rubber cement. It takes just a minute or so to fix a hole in any size tire. I bought a repair kit last summer that includes both tools and about 60 patches. It’s not cheap at $42 (smaller kits are available) but it has a guaranteed shelf life of 6 years, so I just tucked it away in my truck along with a small 12-volt air compressor. When I got a nail in a trailer tire last fall, I had the hole plugged and the tire blown back up in less than 10 min.”