Real farmers rate what they bought, from FARM SHOW MagazineSubscribe  ·  Free issue  ·  Send us your Best or Worst Buy
Subscribe to FARM SHOW
Home › Issues › Vol. 23, No. 4 (1999)

Best & Worst Buys: FARM SHOW Vol. 23, No. 4 (1999)

98 reports from pages 14–17 · 91 Best Buys19 Worst Buys · See everything in this issue at FARM SHOW →

Worst Buy

Truck & Tractor Parts (TTP

Greg Paplham, Two Rivers, Wis. · Vol. 23, No. 4 (1999), p. 14

As a mechanic at Strutz Farms, Greg’s responsible for keeping the tractors running, including a 1984 White 2-180 used for tillage work and silage chopping. In January of 1998, the tractor’s original Caterpillar 3208 engine had more than 6,000 hours on it and was on its last legs. That’s when the farmers decided to repower the tractor with a Caterpillar 3208T, upgrading to the turbo to keep up with the demands of the growing operation. They bought a rebuilt engine at Truck & Tractor Parts (TTP) in Warsaw, Ind. which turned out to be their “worst buy”.

“They told us on the phone that they had a 3208T ready to go but they’d need a cashier’s check for $5,700 because we were from out-of-state. So my boss and I loaded up the 3208, which we were trading and drove the 6 1/2 to 7 hours to Indiana. They told us they still had to rebuild us an engine. Even though we’d been told they had an engine in stock, we reluctantly agreed to have them build one for us anyway. So we went home without an engine.

“When it arrived three days later, we were assured the engine had been dynoed and was field ready. We installed it and got the tractor into the field toward the end of April. After 40 hours, it started using a little oil, then a lot of oil. TTP agreed to pay the freight to return the engine. After examining it, they said it had ingested dirt and that it would cost $3,400 to fix it.

“We got the engine back in a couple of days, installed it, and were back in the field the same evening. That night it used 1 gal. of oil in three hours, yet there were no visible external leaks. This time TTP claimed it simply had to be broken in properly. We went round and round with the company for three months, during which time the engine used about a barrel of oil in 300 to 350 hours.

“TTP finally agreed to rebuild the engine a third time for $6,800 so we sent it back to them. We changed our minds right away, however, and decided to rebuild it ourselves. We bought $2,800 worth of parts directly from Caterpillar and sent the engine to Polk Diesel in Green Bay, where they looked at the block and heads and machined them out to exact factory specs. We took the injectors, injection pump and turbo to Diesel Specialists in Green Bay for examination. Between the two companies we learned that the cylinder walls were .003 to .005 in. out of round, the valve guides were bad, six of the eight injectors were bad, and the injection pump was set wrong - for trucks, not ag applications. The governor weights were also worn out and the turbo showed no signs of abrasion in the compressor housing and impeller wheels, which discounted TTP’s earlier claim that dirt in the engine was the root of the problem. Fixing all these problems cost more than $2,600.

“Finally, last January, I reassembled the engine, installed it and broke it in myself. After 22 hours, the tractor used only 2 qts. of oil.

“We figure we’re out about $20,000, including tractor rental while the White was down.”

Best Buy

Ford 9N

Coy Cleveland, Paradise, Texas · Vol. 23, No. 4 (1999), p. 14

“Our best buy was a 1939 Ford 9N my dad purchased as a demonstrator in the spring of 1940. The Old Racket Box, as we called it, averaged 100 hours a year for 17 years. It was used for plowing and feeding cattle and spent countless hours on a belt pulley powering a wooden Keystone peanut picker. Besides general maintenance, the tractor had only one engine overhaul, one broken axle and one repair to the 3-pt. in the 17 years we owned it.”

Worst Buy

Ford F-250 XLT 4-WD pickup back

Virgil Newberg, Hinton, Iowa · Vol. 23, No. 4 (1999), p. 14

Virgil has taken his “worst buy” 1999 Ford F-250 XLT 4-WD pickup back to the dealer an average of once a month since he bought it last September. “For one thing, I’ve replaced bad transmission sensors three times because the truck wouldn’t shift right.

“But the big problem is with the power steering oil cooler and the air conditioning unit. With the new, raised front bumper on the 1999 models, the power steering cooler unit is now located too low for off-road use. Even though there’s a rubber deflector that extends about 2 in. below the bumper, we break the unit or pull off the hoses every time we drive across corn stalks. I even had a neighbor tell me he had the same problem when he drove over a ridge of plowed snow last winter. Because the air conditioning unit is located directly behind the power steering cooler, it’s also very susceptible to bent fins when you drive across corn stalks. What these trucks really need is a steel deflector or skid plate under the front bumper, rather than the flimsy rubber deflector they’re equipped with. We called Ford several times about the problem, but they’ve never returned our calls.”

Best BuyWorst Buy

Century 100 MIG welder + 2 more

Gordon T. Redel, Red Deer, Alberta · Vol. 23, No. 4 (1999), p. 14

“The worst welder I ever owned was a 1998 Century 100 MIG welder. I wanted to use it in various buildings but discovered it needs at least a 20-amp fuse. Most fuses in my buildings are 15-amp so you’re limited as to where you can use it. It actually wasn’t a bad welder for light work, but the wire kept balling up inside the machine. After I used it a couple of times, I traded it for a 1998 Lincoln 155 MIG welder at the local Princess Auto store where I bought the Century. The Lincoln’s a best buy. It’s just an all-around good welder.”

Worst Buy

Case-IH 4200 mulch tiller

Tim Crawford, Janesville, Wis. · Vol. 23, No. 4 (1999), p. 14

“Performance was disappointing,” says Tim, unhappy with his Case-IH 4200 mulch tiller. “It ridged in the middle of the row and the rear gangs had a tendency to plug up. My dealer re-angled the front gangs, and that has made a tremendous difference.”

Best Buy

Husqvarna 225 L Pro

Keith Brown, Cedar Falls, Iowa · Vol. 23, No. 4 (1999), p. 14

“My hands don’t get numb after using it for two or three hours, the way they did with other trimmers I’ve used,” says Keith, pleased with a Husqvarna 225 L “Pro Series” weed trimmer he bought in 1996. “I’ve had no problems with it. It’s a joy to use.”

Worst Buy

John Deere 726 mulch finisher

Robert Banks, Lynchburg, Ohio · Vol. 23, No. 4 (1999), p. 15

“One of my worst buys ever was a Deere 726 mulch finisher. The drawbars that hold the baskets and spike tooth assembly on the back were built wrong at the factory. The dealer told me to buy some steel plate and make some shims because the company didn’t have the correct parts even after the machine was in production a year. Another problem is that the hydraulic lock-up will not hold the machine up.”

Best BuyWorst Buy

Caterpil lar + 2 more

Rodney E. Jarrells, Granite Falls, Wash. · Vol. 23, No. 4 (1999), p. 15

Rodney’s pleased with his Caterpillar D6M LPG equipped with finger-tip dozer control. He uses it to rough shape and finish golf courses. “The machine is comfortable to operate, among other things. It can work in mud 3 ft. deep and still push dirt. It has automatic shift which is a real time saver because when you’re pushing hard in second gear it’ll automatically shift into first gear. That also makes it easy on fuel.”

On the negative side, Rodney’s “worst buy” is an Acer CD recorder he bought last October to back up his bookkeeping. “It didn’t work so I contacted the company and they replaced it. However, the new one didn’t work either. After four attempts at trying to have it replaced, I asked for my money back. The company told me they didn’t give refunds.”

Best Buy

John Deere 7810 equipped

Robert Ziegenhagel, Medicine Hat, Alberta · Vol. 23, No. 4 (1999), p. 15

“It’s comfortable and easy to operate. I’m not completely exhausted at the end of the day like I have been with some other tractors,” says Robert about his 1997 Deere 7810 equipped with MFWD and self-leveling loader. “When baling, you simply knock the shuttle shift transmission into neutral, finish tying the bale, then knock it back into gear without ever having to touch the clutch pedal.”

Best Buy

Cub Cadet lawn tractor

Robert A. Lanford, Richmond, Va. · Vol. 23, No. 4 (1999), p. 15

Robert’s “best buy” is his 1996 Cub Cadet 2086 lawn tractor. It’s powered by a 20 hp water-cooled Kawasaki engine and is equipped with a 60-in. deck. “The 60-in. deck helps it hold well on banks. It has separate brakes which also helps stability on hills. I have only two complaints. One is that the deck does not raise as high as I’d like, so you have to be careful crossing uneven land. Also, the drive belt on the deck doesn’t last as long as I think it should.”

One modification he made to the tractor was adding a weight to the uphill wheel to increase stability.

Best Buy

Ford F-250 4-WD pickup

Brandon C. White, Hillsboro, Ill. · Vol. 23, No. 4 (1999), p. 15

“We use it for everything, from hauling grain with a 16-ft. gooseneck trailer to pulling a triple axle 10-ton pin-hitch trailer that usually has a 1,100-gal. water tank on it,” says Brandon about a 1983 Ford F-250 4-WD pickup he and his dad, Chad, call their “best buy”. Powered by a 6.9-liter V-8 naturally aspirated diesel, it was purchased with 190,000 miles on it in 1992 for $5,000. It now has 290,000 trouble-free miles on it. “My dad has had many different pickups, but this is the best one by far.”

Worst Buy

Titan six-tower mini center

H.S. Thorington, Palisade, Wash. · Vol. 23, No. 4 (1999), p. 15

His “worst buy” is a Titan 2000 six-tower mini center pivot irrigation system he bought new three years ago. “It’s poorly designed and constructed. The drivetrain is especially bad. I complained to the company, but they didn’t do anything and have since gone out of business. I beefed up the towers, rebuilt he end tower, and installed new gears.”

Best Buy

New Holland TR88 combine + 1 more

LeRoy Alt, Pacific, Mo. · Vol. 23, No. 4 (1999), p. 15

“It’s an excellent machine, a great value for the price,” says LeRoy, pleased with his 1997 New Holland TR88 combine. “It works great and dealer service has been outstanding.”

LeRoy lists his Hiniker 3300 field cultivator as a “worst buy”. “The frame is weak and has broken several times. The pivot bearing on the tandem axle doesn’t last more than a season at best. It also has a poor paint job.”

Best BuyWorst Buy

Versatile 555 tractor + 1 more

Glenn Allen, Mt. Vernon, Ohio · Vol. 23, No. 4 (1999), p. 15

Glenn’s “best buy” is a 1981 Versatile 555 tractor he bought used. “It starts easily even in the coldest weather and it’s easy to work on because of its component design.”

On the negative side, he lists his Bush Hog 1000H backhoe. “I bought it new to put in short strips of tile. It worked OK until it got hot, then you couldn’t raise the bucket out of the ground. I talked to both my dealer and the company, neither of which were much help. I found out later the oil tank was too small for the self-contained hydraulic system and the heat build-up was ruining pumps. I finally sold the thing, after telling the buyer of its history, and replaced it with a Deere industrial hoe that I mounted on a Deere 3020.”

Best Buy

Ford F-150 4-WD XLT equipped

Kody Nielsen, Paul, Idaho · Vol. 23, No. 4 (1999), p. 15

“I bought it new in 1997 and am happier every day with my purchase,” says Kody about his “best buy” Ford F-150 4-WD XLT equipped with extended cab and short box. “The 5.4-liter Triton engine has plenty of power for farm work. It has no trouble pulling loaded trailers, although the springs are too light for really heavy loads. I’ve put over 53,000 miles on it in two years and it’s required nothing more than routine maintenance. This pickup has been nothing but a pleasure to drive, whether in the field or on the freeway. I call it the Cadillac of Workhorses.”

Best BuyWorst Buy

Chevrolet dually pickup powered + 1 more

Robert O. Martin, Brookhaven, Miss. · Vol. 23, No. 4 (1999), p. 15

“The transmission went out at 8,000 miles,” says Robert, unhappy with his 1998 Chevy dually pickup powered by a 6.5-liter turbo diesel engine. “The engine won’t rev up for at least five minutes when the temperature’s below zero.”

On the other hand, he’s had good luck with his 1994 GMC dually powered by a 6.5-liter turbo diesel. “I’ve had no problems in 100,000 miles and four years.”

Worst Buy

Jet mini metal lathe

Robert Takos, Attica, N.Y. · Vol. 23, No. 4 (1999), p. 15

Robert’s unhappy with his Jet mini metal lathe. “It’s the poorest quality tool I ever bought. The metal’s weak and the threading tool bar bent, then fell off. Rotation can’t be stopped with the clutch so I have to turn off the whole machine.”

Best Buy

Kawasaki KE 100 motorcycle

Andy Steinkamp, Woodburn, Ore. · Vol. 23, No. 4 (1999), p. 15

Andy’s “best buy” is a 1992 Kawasaki KE 100 motorcycle he bought last winter. “At first, it was geared too high so I changed sprockets. Now it has plenty of power and goes anywhere. It starts on the first kick and runs great. The oil injector is the nicest thing. You put gas in one tank and 2-stroke oil in another.”

Best Buy

Dixon ZTR mower

Arvin Larson, Ray, N. Dak. · Vol. 23, No. 4 (1999), p. 15

“It has plenty of power and is easy to use in areas that a conventional riding mower couldn’t get into,” says Arvin about his Dixon ZTR mower. “It’s easy to operate and makes lawn care a breeze.”

Best Buy

Abbriata mini baler

Ed Vollborn, Jackson, Ohio · Vol. 23, No. 4 (1999), p. 15

As leader of Ohio State University’s grazing program in the southern district, Ed says the Italian-made M50 Abbriata mini baler he’s been working with for a year shows a lot of potential but still has some bugs to be worked out (Masters Farm Supply, Rt. 3, Box 392, Hwy. 73, Altha, Fla. 32421; ph 850 762-3221 or 3793 or 4322).

“We bought it to make 50-lb. round bales,” he says. “It definitely makes a nice, firm, stand-up bale when you can get the hay to go through it. It has only a 35-in. throat so the problem is that pickup capacity is very limited. We can’t bale our big 9-ft. swaths without plugging it up, particularly in first-cut hay. We had better luck in regrowth hay, but we need some fine-tuning in both the equipment and operator skill if it’s to work properly in our system. The distributor has been most helpful in trying to resolve our problems.”

Best Buy

Case-IH

James Stadtmueller, Monticello, Iowa · Vol. 23, No. 4 (1999), p. 15

James likes both of his Case-IH 5250’s equipped with MFWD. “They’re a lot of tractor in a 105 hp class. They use 2 to 2 1/2 gals. of fuel per hour, which is a lot of work per gal. They’ve got good visibility, a comfortable cab and are easy to enter and exit. I can’t say enough good things about them.”

Best Buy

Ram 2-WD pickup equipped

Willard Donahey, Utica, Ohio · Vol. 23, No. 4 (1999), p. 15

“It has plenty of power and speed and the drive train and frame are built rugged,” says Willard about his “best buy” 1998 DodgeRam 2-WD pickup equipped with a 360 cu. in. engine and automatic limited slip rear axle. “The limited slip rear axle will get you out of some sticky spots. It gets decent gas mileage, even pulling a tandem trailer and car hauler trailer.”

Best Buy

Honda transfer pump

Darwin Congdon, Galesville, Wis. · Vol. 23, No. 4 (1999), p. 15

“It has plenty of power for pumping liquid fertilizer through even the finest filter,” says Darwin, happy with his 5.5 hp Honda transfer pump. “The motor starts on the first pull every time in both hot and cold weather, and even after long periods of being outside.”

Best Buy

John Deere 6-WD Gator heads

Kenneth L. Smith, Waterloo, Ind. · Vol. 23, No. 4 (1999), p. 15

A 1997 Deere 6-WD Gator heads Kenneth’s list of “best buys”. “Works great for picking up stones in no-till soybeans and lots of other chores around the farm It has a real handy hydraulic dump bed and is built heavy enough to do any kind of chore. It’s also easy for my wife to drive.”

Best Buy

DeWalt cordless drill + 1 more

Larry Schulze, Clifton, Texas · Vol. 23, No. 4 (1999), p. 15

Larry’s 1999DeWalt cordless drill is one of his “best buys”. “It has lots of power and I like the keyless chuck and 1-hour quick-charge batteries. I also like the 1/2-in. chuck and the variable torque settings. I haven’t used another electric drill since I bought this one.”

Another of his “best buys” is a 1998 Miller 130 wire feed welder. “It’s a 120-volt, 130-amp welder weighing just 85 lbs. so it’s very portable. I use it both in my shop and in the field, powering it with a 4,000-watt portable generator I have in my truck.”

Best Buy

Guerney’s

Darrell Gerber, Monroeville, Ohio · Vol. 23, No. 4 (1999), p. 15

“I plant a garden every year and have always purchased my seed from Guerney’s in Yankton, S. Dak., but no more. Two years in a row my order was not filled, but my checks were cashed. This spring a $12 item was never sent. I called them three times and three times they said my order would be sent, but I never received it. They can take me off their mailing list.”

Best Buy

Farm King snowblower + 1 more

Tom Wessman, Albert City, Iowa · Vol. 23, No. 4 (1999), p. 15

Tom liked a friend’s Farm King snowblower so much, he bought one of his own. “One thing I don’t like is that they changed shear bolt designs on the pto, switching from a single 3/8-in. bolt to two 1/4-in. bolts. They’re nearly impossible to put in.”

He’s also pleased with his Art’s-Way P.M. 30 grinder/mixer. “I average a load a day, so it gets used a lot,” he says. “They could make it easier to grease. Also, it’s a 1,000 rpm pto so the #60 roller chains don’t last more than 6 months, even though I oil them regularly.”

Best BuyWorst Buy

Ford 5000 utility tractor + 1 more

Oliver B. Matt, Moiese, Mont. · Vol. 23, No. 4 (1999), p. 15

“All I’ve put into it are new tires and fuel,” says Oliver about a 1968 Ford 5000 utility tractor he bought used. “It’s my only tractor and it gets used hard every year for field work, haying and all my other chores. It’s easy on fuel and it always starts.”

On the negative side, he’s had bad luck with his 1997 McCulloch chainsaw. “The whole starting mechanism fell off after the first hour of use. After it was repaired, it never started right again without priming it. I gave it away for use as an exercise machine, because you could sure build up your arm muscles pulling on the rope trying to start it.”

Best Buy

Sunflower 6000 + 2 more

Dale Orman, Maywood, Neb. · Vol. 23, No. 4 (1999), p. 16

One of Dale’s “best buys” is a 1997 Sunflower 6000 series land finisher equipped with hydraulic coulters, shovels and tine harrows. “It provides a perfect one-pass seed bed in corn-stalks when planting irrigated corn on corn.

“I’m also very pleased with my Micro-Trak ST424 planter monitor. I use it on an 8-row Case-IH 800 air seeder. I kept the air seeder’s original monitor and added the new one. It gives me extra confidence and data.”

Another “best buy” is Dale’s Honda 4514 riding mower. “It has a water-cooled automotive-type engine. It’s the most trouble-free mower I’ve ever owned.”

Worst Buy

Farmall 706

Glen Buckingham, Fairfield, Iowa · Vol. 23, No. 4 (1999), p. 16

Glen’s having a hard time shifting gears on his 1966 Farmall706. “There are lemon laws for cars and trucks, so why not tractors? I’ve complained about the problem to my local dealer, but have received little or no response. International Harvester should be responsible for the needed repair, not the farmer.”

Best BuyWorst Buy

Delta Crossaver tool box + 1 more

Joe Thomas, Mattson, Miss. · Vol. 23, No. 4 (1999), p. 16

Joe’s “worst buy” is the Delta Crossaver tool box he bought for his pickup in 1997. “I couldn’t shut the lid from the driver’s side from the beginning. Then, most of the time when driving down the road, the lid would open up and I’d have to stop to close it. The tool box also leaked in heavy rain. I called the factory but did not get any satisfaction from them. I’ve since bought a United Welding box that is much better and cheaper.”

Best Buy

Trelleborg

D. Thomson, Napa, Calif. · Vol. 23, No. 4 (1999), p. 16

In 1998, he equipped his Ford orchard tractor with Trelleborg bias-ply flotation tires so he could get into his vineyard sooner without creating compaction. “As great as the tires are in wet or moist soil conditions, they can barely make it though the vineyard when the grapes are ripe, approximately mid-summer.”

Best BuyWorst Buy

Ford F-100 pickup equipped + 1 more

Charlie Bratton, Albuquerque, N.M. · Vol. 23, No. 4 (1999), p. 16

One of Charlie’s “best buys” is the Ford F-100 pickup equipped with a 292 cu. in. engine he purchased new in 1962. Another is a Ford F-100 pickup equipped with a 350 cu. in. engine that he purchased new in 1973. “My 1962 F-100 has 327,000 miles on it. It still has the original engine and uses only about 2 qts. of oil every 800 miles. It runs like new. I’m also well pleased with my 1973 Ford F-100.”

On the negative side, he had trouble with a Gannon 8-ft. flip-over blade he special ordered from the factory. “The bushings the blade mount on were 5/16-in. under sized. With too much play, the first time I used the blade it fell off the framework. However, the dealer installed the proper bushings and shafts at no charge. They did a good job on it and got it working properly.”

Best BuyWorst Buy

Panasonic Gunslinger 260 welder + 1 more

Joe Meyer, Williamsburg, Ind. · Vol. 23, No. 4 (1999), p. 16

Joe’s “best buy” is a 1998 Panasonic“Gunslinger” 260 welder. “This welder has the capacity for heavy steel as well as light 18 to 20-gauge material. The additional stick feature gives you the versatility of quickly doing a wide range of tasks, including hard surfacing and working with cast iron.”

On the “worst buy” side, Joe lists his 1998 DodgeDurango SLT. “This vehicle is grossly overrated. Dinky visors are just one example of the many design shortfalls. The heating system isn’t even adequate to keep everyone warm in the front seat. Unfortunately, we didn’t recognize these problems until six months after we bought it. If you’re in the market for an SUV, my advice is to buy something other than a Durango.”

Best Buy

Ford-New Holland 1720 tractor + 1 more

Paul Burrows, Sutton, Mass. · Vol. 23, No. 4 (1999), p. 16

“I’m 54 years old and this is the first tractor I ever bought new. It’s great,” says Paul about his 1995 Ford-New Holland 1720 tractor. “It starts, runs and shifts fine. The four-wheel drive works great in mud and snow and it’s easy on fuel and easy to service.”

On the other hand, he’s unhappy about one aspect of the tractor and the Ford 7108 loader be bought to use with it. “The tractor’s hydraulic system has no power. The dealer says that’s just the way OSHA wants it. Also, all the welds on the loader frame broke during light snow removal, and the tractor had less than 200 hours on it.”

Best Buy

Polaris Xplorer 4-WD ATV

John McAdams, Dalhart, Texas · Vol. 23, No. 4 (1999), p. 16

John’s “best buy” is the 1999 PolarisXplorer 4-WD ATV he uses for checking his center pivot irrigation system and other chores. “Four-wheel drive is more versatile and comes in handy in sticky spots. I like the automatic transmission better than standard. Bigger tires give you more ground clearance but really aren’t worth all the extra money. I think the 300 cc engine is big enough for most uses on the farm.”

John purchased an ATV trailer to use for hauling rocks, grass and firewood.

Best Buy

Ford F-150 pickup equipped

Garlon Peterson, Wild Rose, Wis. · Vol. 23, No. 4 (1999), p. 16

Garlon’s annoyed by a problem with his 1989 Ford F-150 pickup equipped with a 300 cu. in., 6-cyl. engine and 5-speed transmission. “It doesn’t cruise smooth at low load and low speed, but runs fine under load. I’ve driven other pickups with standard transmissions that do the same thing, whether they’re V-8’s or 6’s. It drives me nuts.”

Best Buy

Polaris 500 Scrambler

Troy Goode, Cox’s Creek, Ky. · Vol. 23, No. 4 (1999), p. 16

Troy’s generally well pleased with his 1999 4-WD Polaris 500 Scrambler. “It’s more of a sport racer-type four-wheeler than a utility-type ATV. But that doesn’t mean you can’t chase cows or scout crops with it. It’s a little faster than many ATV’s, and I really like the automatic transmission, 4-WD, electric start, reverse and its high speed.”

However, the machine also has a few problems, Troy adds. “One is how weak the rims seem to be. They dent too easily. Another problem is how heavy this machine is. It weighs 542 lbs., which is pretty heavy for a sport racer-style bike. This is probably one of the reasons the rims dent easily. I’d like to see the manufacturer equip it with stronger rims. It would also be nice to have a light showing when 4-WD is engaged.”

Troy’s 1984 200X Honda three-wheeler is also a “best buy”. “It’s one of the best ATV’s ever built, in my opinion.”

Best Buy

Honda Recon

Charles Ries, Shellburg, Iowa · Vol. 23, No. 4 (1999), p. 16

“It handles well, turns short, has a handy electric starter and good suspension,” says Charles about his 1998 2-WD Honda Recon. “One of my complaints is that they need to equip it with an hour and mileage meter so you know when it’s time to service it.”

The ATV is equipped with front and rear racks, which come in handy for such jobs as fixing fence and hauling seed, Charles says.

Best Buy

Yamaha + 1 more

Billy Bishop, Section, Ala. · Vol. 23, No. 4 (1999), p. 16

Billy owns a 1989 Yamaha and a 1987 Kawasaki. “The Yamaha is stiff riding because of its ‘shockless’ design. The Kawasaki has a softer ride, but will dump you because it’s built for speed. The small batteries my ATV’s are equipped with don’t last more than six months. They should be equipped with full-size 12-volt batteries. Also, frames and brakes should be stronger. The brakes have to be repaired too often.”

Billy built a 12-volt sprayer to use on fence rows and in the garden. “It’s similar to most commercial units but was cheaper to make. All it cost was price of the pump, plastic drums, hose clamps, and wire for the battery.”

Best Buy

Yamaha Big Bear

Gary Seim, Pelican Rapids, Minn. · Vol. 23, No. 4 (1999), p. 16

“It’s the best buy I’ve ever made on a recreational vehicle,” says Gary about his 1993 2-WD Yamaha Big Bear. “I haven’t so much as changed a spark plug on it, even though I use it daily to check cattle and snow plow.”

However, Gary says the manufacturer

should make the oil plug easier to get at. “I

also wish they’d equip the engine with rope

start for emergencies.”

Best Buy

Kawasaki Bayou 220

Alan Horn, Weeping Water, Neb. · Vol. 23, No. 4 (1999), p. 16

Alan’s pleased with his 1993 2-WD Kawasaki Bayou 220. “It’s easy to drive and load into the back of my pickup. It’s also easy on gas. The only way it could be improved is to make it easier to start in winter.”

Alan mounted a toolbox on the front rack to carry an assortment of tools.

Best Buy

Honda TRX 300

Cecil F. Fulmer, Gilbert, S.C. · Vol. 23, No. 4 (1999), p. 16

“I received a recall notice about a small problem with the starter which the dealer replaced. I’ve had no other problems since,” says Cecil, happy with his 1995 Honda TRX 300. “There are no changes that could improve it, in my opinion.”

Best Buy

Honda 2-WD + 1 more

Elton Dale Bahm, Independence, La. · Vol. 23, No. 4 (1999), p. 16

Elton’s happy with his 1996 Honda2-WD. “I like the engine, as I do all my Honda engines.”

He purchased a Fimco LG-114 14-gal., 12-volt sprayer form Home Depot to use for spot treating with Roundup. “It’s an excellent buy and works like it’s built for an ATV, which it wasn’t.”

Best Buy

Honda 300

Gaylin Tanner, Declo, Idaho · Vol. 23, No. 4 (1999), p. 16

“I’ve put I don’t know how many miles on it with nothing more than routine maintenance,” says Gaylin about his “best buy” 1989 Honda 300. “However, I would like to see the manufacturer put grease zerks on the tie rod ends and a twist throttle instead of a lever. I’d also like a larger opening in the oil filter hole and see it located in a handier spot.”

Best Buy

Honda TRX 125

Mark Denton, Denton, Kan. · Vol. 23, No. 4 (1999), p. 16

“It was one of the first 4-WD’s on the market and has been, for the most part, extremely reliable,” says Mark, well satisfied with his 1985 Honda TRX 125. “One problem I had is that the front brakes were poorly designed and the cables broke or bound up frequently. Hydraulic brakes would have been a great improvement.”

Best Buy

David Brown 995 diesel tractor

Jess Southard, Topeka, Kan. · Vol. 23, No. 4 (1999), p. 16

Jess’s “best buy” was the English-built David Brown 995 diesel tractor he bought new in 1974. “It was a heavier-built tractor than any other brands rated at 58 hp. The salesman convinced me it was the most economical tractor built. He was right, as it would use only 3 gals. of fuel per hour pulling a 3-bottom plow. On all other work, such as baling hay and loader use, it would use only 1 1/2 gals. per hour.

“I sold out in 1997 and the David Brown brought $800 more than I paid for it new. I checked with the man who bought it, and he says he’s had no trouble with it. He’s also impressed with its performance.”

Best Buy

John Deere 820

W. Gray Abercrombie, Broad Run, Va. · Vol. 23, No. 4 (1999), p. 17

“I’m well satisfied with my 1972 Deere 820. It’s a small tractor but it’s big enough for my small acreage. The 3-cyl. diesel engine is economical and powerful and has good hydraulics. It’s also handles nice and is easy to drive. I wish it had arms or handles that would allow the operator to manipulate each of the 3-pt. lift arms independently from the seat to make the 3-pt. easier to hook up. These arms or handles would be in addition to the existing 3-pt. lift controls. I also wish it had an auxiliary handle that would allow the 3-pt. to be operated from the ground.”

Best Buy

Oliver 1655 + 1 more

John Hett, Palmer, Alaska · Vol. 23, No. 4 (1999), p. 17

John likes his 1975 Oliver 1655 and 1650 tractors. “The 1655 starts easy, handles comfortably, and requires minimal maintenance. The 1650 isn’t as comfortable and I’ve had more problems with it.

“My 1975 Minneapolis Moline 955 required two costly overhauls due to a cracked oil filter can. The filter still pulls out lots of black soot.”

Best Buy

Ford-New Holland 8770 Genesis tractor

Dewey Gilliam, South Pittsburg, Tenn. · Vol. 23, No. 4 (1999), p. 17

Initially, Dewey had problems with the cooling system in the 1995 Ford-New Holland 8770 Genesis tractor he purchased used. But it eventually became a “best buy”. “My local dealer and the manufacturer repaired the tractor far beyond my expectations. After several attempts to solve the problem, a new engine was installed. I received exemplary dealer and manufacturer service and support.”

Best Buy

I’ve learned the hard way on my Ford 5640 tractor with a 12 by 12 tran

Richard Jaescke, Northampton, Mass. · Vol. 23, No. 4 (1999), p. 17

“I’ve learned the hard way on my Ford 5640 tractor with a 12 by 12 transmission and shuttle shift that I have to make sure I come to a complete stop from forward to reverse or you will tear the clutch facing off.

“I’ve also had problems with my 445C Ford tractor loader. Micro switches for the clutch disconnect can stop the tractor from moving if they break for any reason.”

Best Buy

John’s problems with his Morton Building date back many years

John P. Voight, Wichita, Kan. · Vol. 23, No. 4 (1999), p. 17

John’s problems with his Morton Building date back many years. He put up a 54 by 90-ft. machine shed in 1976 and was never happy with it. “It is white with green doors on two sides. The white siding - with baked-on enamel paint - was two different shades of white. When I complained, the company refused to replace the metal. They just spray painted it. The building leaked like a sieve. I could have raised a bumper crop of rice inside. I hired a carpenter to pull most of the nails and replaced them with screws. Later, when I damaged a piece of sheet metal on one of the doors, Morton refused to sell me one sheet to repair it. They would only sell me a whole new door, which they would install at a cost of $2,500.”

Best Buy

International Harvester 806 diesel tractor + 1 more

Larry Armbruster, Ellis, Kan. · Vol. 23, No. 4 (1999), p. 17

A 1967 International 806 diesel tractor rates as one of Larry’s “best buys”. “It starts easy, even in cold weather, and pulls what I want it to. It hasn’t needed any major repairs. I made a small adjustment to the timing and fuel injector pump to boost the power.

“My 1975 Great Bend 800 front-end loader has held together very well.”

Best Buy

Farmall Super M

Thomas A. Bedwell, Betterton, Md. · Vol. 23, No. 4 (1999), p. 17

“I’m well satisfied with both my 1953 Farmall Super M and model H. The Super M has enough power for big jobs while the H is more economical for smaller jobs. I converted the electrical system to 12-volt with alternator, starter, and rewired with 10- and 12-ga. wire. It provides more power for lights and electrical accessories. Case-IH should start making mid-sized gas tractors and offer a complete line of equipment for small and medium size farms. That’s one reason there’s such a demand for 20 to 50 hp gas tractors.”

Best Buy

John Deere 4240

Jim Gruber, Lansing, Iowa · Vol. 23, No. 4 (1999), p. 17

“We use it almost every day of the year for chores. It’s very reliable,” says Jim, happy with his 1981 Deere 4240. “The engine had more than 8,000 hours on it before it needed any repairs. We use a Deere 148 front-end loader with it.”

Best Buy

John Deere 4430 + 2 more

Walter Wilkens, Albert City, Iowa · Vol. 23, No. 4 (1999), p. 17

“I’m retired now but when I farmed I really liked my 1977 Deere 4430. It was very reliable and on a per-acre basis was the cheapest running tractor I ever owned. Very quiet and smooth running. The only problem I ever had was when the high-low powershift clutch went out at about 5,000 hours. Apparently it was a factory defect. As far as handling goes this tractor even beat my 1970 Deere 4020. It was rated at 125 hp but easily put out 140 hp - without any modifications. It had a weak hydraulic system on the hitch and the remote cylinders. I understand this was a problem on all the 4430s. The 4020’s hydraulics were much better. The original lights were pitifully weak so I added some more. I also installed front fenders to keep gravel from hitting the windshield and to improve the tractor’s looks.”

“I wasn’t as satisfied with my 1980 Allis-Chalmers 185. It had way too much downtime. The oil cooler sprang a leak and oil got all over everything. The left rear seal went out. The float on the fuel gauge was made of plastic which dissolved and kept plugging the fuel system. I finally replaced it with a brass one. The injection pump jumped out of time and the dealer couldn’t fix it. The air conditioner thermostat never lasted more than a couple of months so I finally replaced it with another brand which worked. The tractor had plenty of power for its size but had a noisy engine. Fuel economy was only fair. The tractor was hard to shift without clashing gears. The power steering was nearly nonexistant under 1,800 rpm’s, which meant that I had to ride the hand clutch when turning while cultivating or planting. It did have a good hydraulic system.“ owner of a 1976 Allis-Chalmers 7040 equipped with a power shift transmission. “The transmission doesn’t have enough different field speeds and the tractor is hard to start when the weather is cool. Otherwise it’s a good tractor.

“My 1969 Allis-Chalmers 190 XT equipped with a 95 hp diesel engine has a lot of power and starts good. It’s also economical to operate.”

Best Buy

Ecklund electric drive-through gates + 1 more

Arlen Doely, Spring Grove, Minn. · Vol. 23, No. 4 (1999), p. 17

“I bought two Ecklund electric drive-through gates last year and am very pleased (Ecklund, Box 700, Breadview, Sask., Canada S0G 0K0 ph 306 696-2508). They’re inexpensive and eliminate the need to get on and off the tractor all the time.

“I purchased a hoop shelter for round bale storage from High Pointe Coverings, Harmony, Minn. I was somewhat concerned whether it could withstand high winds and got a real test last fall. We had winds of more than 70 mph, with one gust clocked at 93 mph. This wind kept on most of the day, but the shelter survived intact.”

Best BuyWorst Buy

Allis-Chalmers 7040 tractor + 1 more

Joe Torkelson, Hiawatha, Kan. · Vol. 23, No. 4 (1999), p. 17

Joe’s the owner of a 1976 Allis-Chalmers 7040 equipped with a power shift transmission. “The transmission doesn’t have enough different field speeds and the tractor is hard to start when the weather is cool. Otherwise it’s a good tractor.

“My 1969 Allis-Chalmers 190 XT equipped with a 95 hp diesel engine has a lot of power and starts good. It’s also economical to operate.”

Best Buy

Ram Dakota 4-WD pickup equipped

Daniel M. Dixon, Fallston, N.C. · Vol. 23, No. 4 (1999), p. 17

A 1987 Dodge Dakota 4-WD pickup equipped with a 3.8-liter, V-6 engine and 5-speed manual transmission, rates as Daniel’s “best buy”. “I had to replace the transmission at 203,000 miles, but that’s been my only expense other than normal maintenance. The clutch was still in pretty good shape but I replaced it anyway.”

Best Buy

Sears Craftsman riding mower equipped + 2 more

Johnie W. Oglesby, Ewing, Va. · Vol. 23, No. 4 (1999), p. 17

“It’s a great performer,” says Johnie about his Sears Craftsman riding mower equipped with an 18 1/2 hp twin cylinder Kohler Magnum gas engine. “It makes a 46-in. wide cut. I also like my Sears air compressor.

“My 1997 Ford F-150 pickup equipped with a 4.6-liter V-8 engine and automatic transmission is a best buy.”

Best Buy

International Harvester 3588 front wheel assist + 2 more

Steve Mottaz, Brimfield, Ill. · Vol. 23, No. 4 (1999), p. 17

“My best buys are my International3588 front wheel assist tractor, International 1460 combine, Deere 7000 planter, and M & W 450R grain dryer. In my opinion these machines were ahead of their time in the way they were designed. I’m proud of them today. Hats off to the engineers.”

Best Buy

RTA 1050 plastic layer

Jay Yankey, Nokesville, Va. · Vol. 23, No. 4 (1999), p. 17

“My 1998 RTA 1050 plastic layer works great on my truck farm. The machine ridges the soil, incorporates a trickle irrigation line, and lays plastic - all in one smooth operation. In the past I had to perform all these tasks by hand. The machine saves many hours of labor and

Best Buy

Poulan 2150 chain saw

Curtis L. Barron, Miles, Texas · Vol. 23, No. 4 (1999), p. 17

“I bought a Poulan 2150, 16-in. chain saw from Walmart and it’s my best buy. It starts easy, is easy to service, runs cool, and has a gas tank that’s easy to fill. It’s truly a customer friendly product. Works good on 6 to 9-in. logs.”

Best Buy

John Deere 7000 planter

Thomas Beane, Fort Atkinson, Wis. · Vol. 23, No. 4 (1999), p. 17

“My Deere 7000 planter was equipped with disc openers when I bought it, but I switched to a shoe planter because I wanted a better seedbed. I also installed no-till equipment on it, including two 8-wave coulters per row that are spaced 3 inches apart. I made the modifications because I wanted to do one-pass tillage and then plant corn.”

Best Buy

Ford pickup equipped + 1 more

Toivo Kujala, Bovey, Minn. · Vol. 23, No. 4 (1999), p. 17

“One of my best buys is my 1978 Ford pickup equipped with a 302 cu. in. engine and overdrive transmission. It has needed very few repairs and the body has only minor rust. It has more than 251,000 miles.

“My 1950 Allis-Chalmers B tractor was a best buy. I used it for 34 years to do snowplowing, haying, logging, and hauling firewood and never had any problems.”