Real farmers rate what they bought, from FARM SHOW MagazineSubscribe  ·  Free issue  ·  Send us your Best or Worst Buy
Subscribe to FARM SHOW
Home › Issues › Vol. 16, No. 3 (1992)

Best & Worst Buys: FARM SHOW Vol. 16, No. 3 (1992)

55 reports from pages 12–14 · 48 Best Buys14 Worst Buys · See everything in this issue at FARM SHOW →

Best Buy

John Deere 750 no-till drill isa + 2 more

David R. Cook, Marshall, Mich. · Vol. 16, No. 3 (1992), p. 12

David R. Cook, Marshall, Mich.: “Our 1991 Hardi TR500 sprayer is a worst buy. Nozzles and nozzle screens plug continuously. Nozzle check valves plug when using dry fIowable materials. Self cleaning screen often plugs. If it does self clean, it sends dirt back into the spray tank. The electric valves open too slow for spot spraying herbicides. The pressure gauges are too ninate suys small and hard to read. Everything is metric and the plumbing is too complicated. When the tank has less than 50 gal. in it, the gauge won't show the volume. When there’s 30 gal. or less in the tank and the sprayer is on sloping ground, the pump will suck air causing the sprayer to lose pressure. It’s very difficult to finish a job without having a lot of leftover chemicals in the tank. “Our 1991 Deere 750 no-till drill isa best buy. We've used it to seed soybeans and wheat in both no-till and conventional till with excellent results. Iteven did a good job seeding beans into irrigated corn ground that hadn’t been touched after harvest. The beans made 53 bu./acre.” Myles C, Elsberry, Wausa, Neb.: “Our 1992 Case-IH 8480 baler is a best buy. It may not make the best looking bales in the world, but we've got the best quality hay we've ever had. We’ ve used it to make over 1,000 bales so far and have had only a few minor problems.”

Worst Buy

Herb Lofy, Richfield, Wis

Herb Lofy, Richfield, Wis. · Vol. 16, No. 3 (1992), p. 12

Herb Lofy, Richfield, Wis.: Herb purchased his “worst buy” DeLaval (New Century) milk cooler in 1983. “We're very unhappy with its performance, It took over a year to getit to work properly, and we had to hire someone on our own to repair it. Just before the 5-year guarantee expired, a seam on the bottom of the tank split due to poor spot welding on the stainless steel. We brought the problem to the attention of factory representatives several times at farm shows, but got no response. The washer has also caused many problems. When the pipe line needed to be updated, we decided to replace the entire system with new Surge equipment. Ithas performed well so far with good dealer service.”

Worst Buy

Glen Phelps, North Platte, Neb

Glen Phelps, North Platte, Neb. · Vol. 16, No. 3 (1992), p. 12

Glen Phelps, North Platte, Neb.: Glen nominates his 1990 Ingersoll-Rand 2 hp, direct drive, single stage air compressor as a “worst buy”. “I’ve used it strictly to fill tires and clean out radiators and have never used it with air-powered tools. It’s very noisy. When it quit last February, I called the toll-free number listed in the owner’s manual and was told that the company division that made this model had been sold, After making many calls to dealers, I learned that the parts needed to repair the compressor were ‘on back order’. It needed a new piston, counterweight, and rotor that cost a total of $587. We paid only $262 for the compressor when we bought it new.”

Best Buy

Warren Lathe, Guilford, Vt

Warren Lathe, Guilford, Vt. · Vol. 16, No. 3 (1992), p. 12

Warren Lathe, Guilford, Vt.: Warren owns a “best buy” 1990 Kuhn E135 tiller. “It’s rugged and well built. I’ve used it on stony ground with no problems. I’ verecommended it to friends who've bought their own, It’s a quality product. “My 1989 Valby chipper is a best buy. really work it hard and use it to chip brush, slabs, and logs up to 6 in. in dia, It takes everything I throw into it.-It’s a quality machine that I’d recommend to anyone. “Some time ago I reported an unsatisfactory purchase of a Morton building that was published in FARM SHOW. The building had a problem and the salesman didn’t report it to the main office. Then an official at the main office read your magazine. Needless to say, I got instant response. The problem was corrected beyond my expectations. FARM SHOW gets the message out and I thank you, I now believe that Morton Building Co. stands behind its products. was so well satisfied that I had the company erect two more large buildings. Their crews are experienced and do excellent work.”

Best Buy

Alvin Shantz, Camrose, Alberta: “My best buy is my 1986 Plymouth Carav

Alvin Shantz, Camrose, Alberta · Vol. 16, No. 3 (1992), p. 12

Alvin Shantz, Camrose, Alberta: “My best buy is my 1986 Plymouth Caravelle rear wheel drive automobile. It has over 35,000 miles and the only problem has been a faulty resistor spark plug that caused the engine to misfire. I change oil every 3,000 miles and never have to add oil. In the summer it gets up to 32 mpg (imperial) on long drives. I installed a carburetor enhancer from Eagle Research (Box 86, Yahk, B.C. VOB 2P0).”

Best Buy

Case IH 7110 Magnum tractor heads + 3 more

Tom Probst, West Liberty, Iowa · Vol. 16, No. 3 (1992), p. 12

Tom Probst, West Liberty, Iowa: Tom says a 1990 Case-IH 7110 Magnum tractor heads his “best buy” list. “I’m extremely pleased with it. It casily pulls a 22-ft. diskchisel plow without lugging down and regains rpm’s very quickly, The powershift transmission is smooth and has speeds where I need them. It’s a pleasure to operate. The cab is quiet and well designed with great visibility. “J uaded a Massey Ferguson 2745 tractor for the Magnum. I wish I had never seen that tractor. I could afford it when I bought it, but in the end the down time and repair costs made it too expensive to keep.” Marcel J. Dufault, Haywood, Manitoba: “I’m a crop adjuster so I travel a lot over rough fields and country roads. I find thatmy 1989 Chrysler Reliant K-car is abest buy. The 2.5-liter engine has plenty of power and is fuel efficient. It drives comfortably and handles well on unpaved country roads. The 5-speed manual transmission makes it nice for driving over fields. It has over 35,000 miles with no problems,”

Best BuyWorst Buy

Makita grinder + 1 more

Paul Hobbs, Kansas City, Mo. · Vol. 16, No. 3 (1992), p. 13

Paul Hobbs, Kansas City, Mo.: “My Makita 4-in, grinder is easy to handle, compact, and has an overload shutoff. It’s a best buy. “My Homelite XL 14-in. chain saw is light and easy to handle. I’ve used it for six years and my only expenses have been fora new filter and new chains. “My Craftsman 3/8-in. electric drill is a worst buy. After I used it about 10 times it started making a howling noise. [ retumed it and got another one, but the same problem happened again.”

Best Buy

Ford Crown Victoria car

Martin Kenzie, Vermilion, Alberta · Vol. 16, No. 3 (1992), p. 13

Martin Kenzie, Vermilion, Alberta: “It’s a decent looking car, one that I’m proud to be seen in,” says Martin, happy with his 1990 Ford Crown Victoria car. “Consistently gets 30 mpg, handles good, and has a nice quiet ride. However, I don’t like the bel! that rings when I open the door without removing the key. It’s annoying. “My worst buy is the Last Perch sparrow trap. It simply doesn’t catch sparrows. I’ve moved it around to different locations like the manufacturer suggests, but with no luck. There are plenty of sparrows around. I don’t know if they don’t fly into the trap, or if they’re able to getoutonce the perch drops.”

Best Buy

Great Plains 12-volt fuel pump

Reg. M. Powell, Whitewood, Sask. · Vol. 16, No. 3 (1992), p. 13

Reg. M. Powell, Whitewood, Sask.: “Our 1991 Great Plains 12-volt fuel pump has done everything the company said it would, It works fast, doesn’t leak, and the automatic shutoff works well, It’s our sec“It has done everything the company said it would.” ond one, but someone else must like them too because ours was stolen.”

Best BuyWorst Buy

Makita 10 mm drill + 3 more

James Smith, Hamlin, N.Y. · Vol. 16, No. 3 (1992), p. 13

James Smith, Hamlin, N.Y.: James likes his 1990 Makita 10 mm drill. “I’ve used it for over a year with no problems. In the past I’ve used Black & Decker, Craftsman, and Skil drills, but none of them lasted more than six months.” On the “worst buy” side, he’s unhappy with his 1989 Ford F-150 pickup. “I had problems with the engine, transmission, power steering, springs, and brakes. The pickup was in the shop 25% of the time. Finally I returned it to the manufacturer under New York's lemon law.”

Best Buy

Hal Meenach, Valleyford, Wash

Hal Meenach, Valleyford, Wash. · Vol. 16, No. 3 (1992), p. 13

Hal Meenach, Valleyford, Wash.: “It should have better shank depth control,” says Hal, who otherwise is pleased with his “best buy” Flexi-Coil 1100 air seeder, “It has good trash clearance and is durable. No broken frame parts or shanks in five years. Saves field trips and is very versatile, We've used it for all our crops, from garbanzo beans to canola, The company handled a few start-up problems quickly and efficiently.”

Best Buy

Stihl 044 chain saw

Larry Cassatt, Carlisle, Penn. · Vol. 16, No. 3 (1992), p. 13

Larry Cassatt, Carlisle, Penn.: “My 1990 Stihl 044 chain saw performs well and is a pleasure to use. Starts easy and has plenty of power to handle the 20-in. bar, even in dry hardwoods. This is the second Stihl saw I’ve owned and I'd buy another one,”

Best Buy

White City

Mike Davis, White City, Ore. · Vol. 16, No. 3 (1992), p. 13

Mike Davis, White City, Ore.: Mike likes the Nikon electronic leveling system mounted on his 1991 Laserplane 350 land leveler. “It gives the driver complete control and allows one-man operation which saves time and labor, It’s easy to use.”

Best Buy

John Deere 6620 turbo dicsel flatland + 1 more

Steven L. Brooks, New Windsor, Ill. · Vol. 16, No. 3 (1992), p. 13

Steven L. Brooks, New Windsor, Ill.: Steven's pleased with his 1983 Deere 6620 turbo dicsel flatland combine, but sys it could use a number of improvements. “It works very good on perfectly flat ground, but poor on slopes, Grain runs over the rear end of the sieve and onto the ground. I cut out grain saver fins above the chaifer inside an old White combine and installed them on the outside edges of the top and bottom sieves (featured in FARM SHOW'’s Vol. 12, No. 1). It lets me harvest three to four times faster on hillsides. The engine gauge should be mounted in front of the operator instead of behind him. The shutoff system that controls hot water for the heater doesn't work right. The dealer replaced our system, but the cab got even hotter than before. We finally installed a plumbing gate valve in the heater hose so that we now have real control over the heat and air conditioning. “The snapping rolls on our Deere 444 corn head are poorly designed due to lack of a lower support bearing. We have to replace the rolls every year. The fingers on our Deere 213 reel head are too short. By the time the fingers reach down to the lodged bean stalks, the reel bats are already shattering standing beans. The reel has a ‘caveman’ pin-and-hole cylinder height adjustment. It should have a cylinder stop spacer that simply snaps onto the cylinder rod.”

Best Buy

Don Klein, Peru, Ill

Don Klein, Peru, Ill. · Vol. 16, No. 3 (1992), p. 13

Don Klein, Peru, Ill.; Don’s happy with his 1991 GM pickup equipped with a 305 cu. in, V-8 engine and automatic transmission. “It doesn’t have any rattles or squeaks and runs perfect. Gets 20 mpg. Glad to see a good U.S. product.”

Best Buy

Curtis R

Curtis R. Hennings, Ritzville, Wash. · Vol. 16, No. 3 (1992), p. 13

Curtis R. Hennings, Ritzville, Wa.: An R & R 21-ft. HD subsoiler is Curtis's “best buy”. “It’s built strong enough so I don’t have to worry about how much tractor horsepower I use to pull it. The parabolic shanks pull much easier than straight shank subsoilers we've used in the past.”

Best Buy

John Deere 158 loader

Duane L. Rodine, Polk, Neb. · Vol. 16, No. 3 (1992), p. 13

Duane L. Rodine, Polk, Neb.: “We use it for something every day,” says Duane, impressed with his Deere 158 loader. “We've seen other brands where the joints are worn oval, but that’s not a problem on this one, It requires little maintenance,”

Worst Buy

Case IH 496 cushion gang disk + 1 more

Merle Spohr, Hancock, Minn. · Vol. 16, No. 3 (1992), p. 13

Merle Spohr, Hancock, Minn.: Merle’s had trouble with his Case-IH 496 cushion gang disk. “The scrapers don’tmove with the gangs, which causes them to bend or break, The bolts that hold the gangs on break, bending the scraper bars. May also break the bearing holders, The manufacturer should stand behind its product, and when they develop an update kit to solve a problem they should contact us instead of expecting us to contact them.”

Worst Buy

Massey Ferguson 550 combine

David Artmeier, Rushville, Ind. · Vol. 16, No. 3 (1992), p. 13

David Artmeier, Rushville, Ind.: David's “worst buy” is his 1986 Massey Ferguson 550 combine. “This combine was just plain junk. We had to install two new clutches in it the first two days we used it. We used it two years before we could go an entire day without breaking down. The company replaced the frame and worked on the hydraulic system, unloading auger, sieves, straw walkers, engine, electrical “We used it two years before we could go an entire day without breaking down.” system, and headers, The day the warranty expired, our dealer said ‘it's your problem now’ and laughed at us. The corn head was so rusty when we got it that we couldn't even adjust the stripper plates. However, the combine does have good capacity and threshing ability.”

Best Buy

Ford 7610 4-WD tractor equipped

James Makowski, Freedom, N.Y. · Vol. 16, No. 3 (1992), p. 13

James Makowski, Freedom, N.Y.: “It has plenty of power and is versatile. We use it every day,” says James, pleased with his 1990 Ford 7610 4-WD tractor equipped with a 7410 loader, “It has 500 hours with no problems. “Our 1979 Ford 7700 tractor has 4,000 hours and still works as good as 1 new.”

Best Buy

Ford

W.J. Thomas Kirk, Marquette, Manitoba · Vol. 16, No. 3 (1992), p. 13

W.J. Thomas Kirk, Marquette, Manitoba: _ He's “very satisfied” with his 1988 Ford New - Holland TR96 combine, bul says it could use a couple of improvements, “I've had some problems with flax straw wrapping around the feeder chain and beater. Also the unloading auger should be speeded up substantially,”

Best Buy

Arthur G

Arthur G. Egbert, Downing, Mo. · Vol. 16, No. 3 (1992), p. 13

Arthur G. Egbert, Downing, Mo.: “My best buy is a Posi Lock gear and bearing puller (Ray-Mac, Inc., Box 457, Gwinner, N. Dak. 58040). Works great for many types of repair jobs.”

Worst Buy

White 195 tractor equipped

Dwight G. Gilbert, Dorr, Mich. · Vol. 16, No. 3 (1992), p. 13

Dwight G. Gilbert, Dorr, Mich.: “My 1991 White 195 tractor equipped with front wheel drive assist always starts and has plenty of power to get the job done.” On the negative side, “I boughta used Landoll Tilloll 15-ft. soil finisher last year. It looked impressive but wouldn’t dig more than 2 to 3 in. deep and the bearings had to be replaced constantly,”

Best BuyWorst Buy

Stihl FS66 brush cutter + 1 more

Floyd W. Plank, Rush City, Minn. · Vol. 16, No. 3 (1992), p. 13

Floyd W. Plank, Rush City, Minn.: “My Stihl FS66 brush cutter is a best buy. I've used it to cut big weeds and small trees up to 2 in. in dia. along fences, around buildings, etc., with no problems. It’s light and easy to service. “My 1991 Craftsman 10-in. belt-driven table saw is a worst buy. None of the guides are perfect so I always have to measure to make sure they’re set right. The blade tends to tilt on its own regardless of how much I adjust the tightener belt.”

Best Buy

Earl S

Earl S. Hofland, Valier, Mont. · Vol. 16, No. 3 (1992), p. 13

Earl S. Hofland, Valier, Mont.: A 1992 Morris 36-ft. Ranger Il] wing up packer harrow heads Earl's “best buy” list. “Itdoes a super job of packing the soil, breaking up clods, and making a firm seedbed. I’ve had some problems with the wing locks, but hope to get this worked out.”

Best Buy

Ram 4-WD truck equipped

Andrew Davidson, Seaforth, Ontario · Vol. 16, No. 3 (1992), p. 13

Andrew Davidson, Seaforth, Ontario: “I'm pleased with my 1991 Dodge 4-WD truck equipped with a Cummins diesel engine and standard iransmission. It’s very fuel efficient. mounted a snow plow on it last winter and it did a great job.”

Best Buy

Ford F-350 4-WD diesel uuck

Mike Nelson, Reed City, Mich. · Vol. 16, No. 3 (1992), p. 13

Mike Nelson, Reed City, Mich.: Mike’s happy with his 1992 Ford F-350 4-WD diesel uuck, “I like the new look of the 1992 Ford trucks, They still use a straight axle in front instead of the independent front suspension that GM uses. The straight axle handles a load better. also like being able to sit up higher for better visibility. The seats make you sit with good posture without giving you a backache. Over all, Ford gives you more truck for your money.”

Best BuyWorst Buy

Vermeer 504 Super + 3 more

Tim Schultz, Clintonville, Wis. · Vol. 16, No. 3 (1992), p. 13

Tim Schultz, Clintonville, Wis.: “My best buy of all time is my silage bagging equipment. ( /y/ .2?. FARM CHOW - 42 Best & W ( I started with a Silopress XPIII (Silopress, 1915 Floyd Blvd., Box 988, Sioux City, Iowa 51102) and now also use a Uni-press. Both systems make it easy to make excellent quality feed for my 65 dairy cows. They’ve allowed me to increase production and profit per acre from forage while reducing the amount! spend on purchased feed. I had been using cement top-unloading silos and Harvestores, but now they stand empty and unused - I can’t afford to use them. “My 1990 KnightReel Augie 2375 TMR pull-type mixer is also a best buy. It lets me feed all my milk cows once a day in about 45 min, and has allowed me to maintain a 20,000-Ib. herd average while cutting purchased feed costs by 40 to 50%. The TMR mixer and silage bagging systems together have greatly increased my profitability. I'll never go back to my old system. “My 1991 Vermeer 504 Super I baler performed just like I expected and makes nice tight bales. The dealer spent plenty of time with me to make sure I knew how to use it I'm completely satisfied. “My Landoll Tilloll implement provides true one-pass spring tillage. Really saves time and fuel. “My Deere 1460 disc mower-conditioner is a best buy. My wife can use it to cut hay at 7 to 8 mph without plugging it up. I’ve tried my hardest to plug it up, but I can’t. If it lasts as long as it’s supposed to, it'll eam ‘best buy’ status. “My worst buy was a 1990 Case-IH Maxxum 5120 tractor. It caused me lots of grief before I traded it in on a Deere. In “If it lasts as long as it's supposed to, it'll earn 'best buy' status.” fairness to Case-IH, it was one of the first models built and I understand that most of my problems have been corrected in later models or by recalls. However, I still feel it has too much electronic equipment for a farm tractor. The 3-pt. took too long to lower for a job like cultivating and trim pieces kept falling off. In cold weather the engine would start fine, but the tractor wouldn't move. The clutch works off electric switches somehow. The dealer bent over backwards to solve the problem but had no luck. I’d recommend the dealer to anyone, but a Maxxum only to my enemies,”

Worst Buy

John Deere 630 wheel disk

Jay Justice, Chetopa, Kan. · Vol. 16, No. 3 (1992), p. 14

Jay Justice, Chetopa, Kan.: “Our best buy isa Krause 4900 wheel disk. We can go from field to field without having to make any adjustments. No problems. “Our Deere 630 wheel disk is a worst buy. It didn’t work right for 6 to 7 months after we bought it. The rear gangs on the wings hang way too low and dig deep holes. When we raised the wings so they didn’t dig, the disk would ridge in the middle. I never could go from field to field without having to adjust something on the disk. I found out that the frame had never been welded level soeverything was off. Ancighbor had the same problem with his model. Whenever someone asks us what kind of disk to buy, we recommend Krause.”

Best Buy

Ford F-150 pickup + 1 more

Charlie Harant, Caldwell, Kan. · Vol. 16, No. 3 (1992), p. 14

Charlie Harant, Caldwell, Kan.:; A 1991 Ford F-150 pickup rates as Charlie's “best buy”. “It rides easy and quiet and is an allaround better vehicle than the 1989 Chevrolet 1500 that I had owned. I sold the Chevrolet after two years. The wind noise was terrible at SO mph. The Ford has a much quieter cab. The only problem is that when the engine is cold it stalls when I accelerate. My dealer hasn’t solved the problem.”

Best BuyWorst Buy

John Deere 72008-row + 1 more

Gary Joachim, Claremont, Minn. · Vol. 16, No. 3 (1992), p. 14

Gary Joachim, Claremont, Minn.: “My best buys are the Osborne hog feeders that I installed in my confinement buildings (Osborne Industries Inc., Box 388, Osborne, Kan. 67473). There’s hardly any waste, they never plug up, and require almost no adjustments. I haven't spent one minute cleaning manure out of them. The only problem is that once in a while a small pig will crawl in and get caught. “My Deere 72008-row planterisn'treally a lemon, but in real wet conditions like we had last spring wet clods stick on the idlers causing the chains to fall off the row units. My neighbor had the same problem. Also, most of the dry fertilizer tubes rusted away after the first year. My old International 400 planter had a much better dry fertilizer hose assembly, I like the spring-loaded idler on the seed and fertilizer transmissions. CaseTH planters have used similar idlers for almost 20 years.”

Best Buy

Ford 7710 tractor + 1 more

Donald R. Morris, Kearney, Mo. · Vol. 16, No. 3 (1992), p. 14

Donald R. Morris, Kearney, Mo.: Donald’s pleased with his 1989 Ford 7710 tractor, but says it could use a couple im* provements. “The clutch and brake pedals are too close together and the hydraulic hose tips are junk. I replaced them with the same tip that’s used on Massey Ferguson tractors. , “My 1988 Hesston 1050 disc mowerconditioner is a best buy.”

Best Buy

Russell H

Russell H. Pennock, Kewanee, Ill. · Vol. 16, No. 3 (1992), p. 14

Russell H. Pennock, Kewanee, [IL.: “My 1989 Belarus 611 tractor does everything well and is a best buy. It pulls great and can'tbeli¢ve how little fuel ituses for plowing and disking. My only complaint is that the pto shaltis difficult to engage and disengage, but that’s aminor problem. The rest of the tractor is fine.”

Best BuyWorst Buy

John Deere semimounted 4-bottom + 1 more

Merlin Atwell, Remsen, N.Y. · Vol. 16, No. 3 (1992), p. 14

Merlin Atwell, Remsen, N.Y.: Merlin’s “worst buy” is his 1990 Deere 2000 semimounted, 4-bottom 18-in. plow. “It’s not built with the quality of Deere’s other products. It doesn’t even perform as well as our 20-year-old Allis-Chalmers semi-mounted auto reset plows. The bolts wear through the points and land sides because there’s not enough taper on them. Three of the moldboards have cracks in them around the front mounting bolts, and the shear bolts continually break from coulter tension. Our dealer has done nothing to help.”

Best Buy

Vermeer 605 J round baler

Dave Anderson, Postville, Iowa · Vol. 16, No. 3 (1992), p. 14

Dave Anderson, Postville, Iowa: “My best buy is my 1989 Vermeer 605 J round baler, I do custom work and have used it to make more than 10,000 bales. I also use it to make cornstalk bales every year. The only repairs have been fora few bearings, chains, and sprockets, and last spring I replaced aboutadozen of the rubber-mounted pickup teeth.”

Worst Buy

Alvin Pearson, Ellsworth, Wis

Alvin Pearson, Ellsworth, Wis. · Vol. 16, No. 3 (1992), p. 14

Alvin Pearson, Ellsworth, Wis.: Alvin likes his portable Super Blast 1200 industrial pressure sprayer (Parker Cleaning Products, Inc., Minneapolis, Minn.). “It has 1,200 Ibs. pressure and is equipped with a siphon intake for adding soap. “My worst buy is a round bale feeder from Sioux Steel Co. We've had to reweld and reinforce three of the six rings so far and each one cost at least $40 to repair. The welds failed between the bottom ring and the upright support to the second ring. I called the company and they had a representative come out and take photos. However, they never called back. recently bought two more feeders from them that are built heavier with a solid steel bottom.”

Best Buy

JCB 930 Rough Terrain4-WD forklift

Ben L. Beiler, Ronks, Penn. · Vol. 16, No. 3 (1992), p. 14

Ben L. Beiler, Ronks, Penn.: “Ithandles like a dream,” says Ben about his “best buy” 1991 JCB 930 Rough Terrain4-WD forklift. “The enclosed cab keeps me warm in the winter and dry when it rains. We love the way it handles and would buy another one if we needed it. The only problem was a bro“We love the way it handles and would buy another one if we needed it.” ken fuel gauge sender.”

Best Buy

New Holland

Amos Z. Sensenig, New Holland, Penn. · Vol. 16, No. 3 (1992), p. 14

Amos Z. Sensenig, New Holland, Penn.: Amos is pleased with his 1991 GM Sierra _ pickup equipped with a 305 cu. in, V-8 engine and 4-speed transmission. “It works just fine. It’s a best buy.”

Best Buy

Craig Moriak, Clayton, Wis

Craig Moriak, Clayton, Wis. · Vol. 16, No. 3 (1992), p. 14

Craig Moriak, Clayton, Wis.: Craig's “best buy” is his Posi Lock gear and bearing puller. “A cage around the jaws keeps them from slipping offas you pull the bearing off. It works excellent.”

Best Buy

Kubota M7500 DT 4-WD tractor equipped

Eric Wallis, Rudyard, Mich. · Vol. 16, No. 3 (1992), p. 14

Eric Wallis, Rudyard, Mich.: A 1981 Kubota M7500 DT 4-WD tractor equipped with a loader rates as Eric's “best buy”. “It has over 4,500 hours of hard use with few problems. Our only expense was foraclutch assembly that we replaced at 3,500 hours. We feed our livestock round bales and use the loader all during the feeding season. We also handle all our manure with it, The loader detaches quickly so we can use the tractor for tillage or hay making. It uses about I 1/2 gal./nr. pulling light loads, such as a Haybine, and up to 2 1/2 gal./hr. for plowing or disking. That's quite respectable for an 80 hp tractor. “Our 1986 Kubota M6950 DT tractor is also a best buy. It has slightly less horsepower than the 1981 model, but is slightly bigger. We use a loader on it also. It had some nuisance problems that the dealer eventually solved, Ithas about 2,300 hours.”

Best BuyWorst Buy

Honda Big Red 4-wheel atv 6 + 1 more

Kenneth Stull, Ethel, Mo. · Vol. 16, No. 3 (1992), p. 14

Kenneth Stull, Ethel, Mo.: A calf warmer made by R.G. Hendrickson of Superior, Wis. which heread aboutin FARM SHOW, heads Kenncth’s “best buy” list. “We've saved several wet and cold calves with this warmer. “Ipurchaseda used 1982 Honda Big Red 4-wheel ATV 6 years ago. I use itevery day and have spent very little money on it. “My worst buy is my 1992 Black & Decker 3/8-in, drill. The chuck won’t stay tight and the trigger doesn’t work sometimes.”