Real farmers rate what they bought, from FARM SHOW MagazineSubscribe  ·  Free issue  ·  Send us your Best or Worst Buy
Subscribe to FARM SHOW
Home › Issues › Vol. 22, No. 2 (1998)

Best & Worst Buys: FARM SHOW Vol. 22, No. 2 (1998)

68 reports from pages 14–17 · 63 Best Buys22 Worst Buys · See everything in this issue at FARM SHOW →

Best Buy

Last year 17-year-old Heath won an FFA award for the custom-baling bus

Heath Barrett, Stuart, Iowa · Vol. 22, No. 2 (1998), p. 14

Last year 17-year-old Heath won an FFA award for the custom-baling business he started in 1996. Last season he baled 2,800 6 by 5-ft. round bales for a dozen customers within a 50-mile radius of his hometown west of Des Moines. Customers were pleased with his work, he says, except for the net wrapped bales he produced with his 1991 Deere 535 baler he bought used for $17,500.

“I originally owned a Deere 530 and traded for the 535 after the first year because I needed the ‘net wrap’,” says Heath. “But the wrapper never worked properly and doesn’t to this day. It leaves about 4 in. on each side of the bale unwrapped. A mechanic from the dealer was out and looked at it four times. He told me the reason I was having problems was that I didn’t know what I was doing. For his four trips and the three I made hauling the baler back to the dealer myself, I racked up $1,600 in repair bills even though the wrapping problem was never resolved.

“I still owe $9,300 on the baler and I’d be much happier about paying it off if it had ever worked right. I’m pretty hesitant to throw good money after bad on more repairs that may not even help. The problems with this baler should have been resolved by the dealer or the manufacturer sometime in the last seven years. I tracked down the man who leased the baler the year before I bought it and he said he had the same trouble.”

Worst Buy

Gehl grinder/mixer

Elton Kropf, Seymour Mo. · Vol. 22, No. 2 (1998), p. 14

Elton’s “worst buy” in 20 years of farming is a 170 Gehl grinder/mixer he bought new in 1990 for $8,900 plus the trade-in of his old mixer.

“It’s actually not a bad mixer, but we got poor company support for numerous problems that started early-on,” Elton says. “Within three months, the chain had rubbed a hole in the U-trough that carries corn from the hammermill to the mixer. We took the machine to the dealer we bought it from and they put on a new trough, but they installed smaller sprockets than the mixer was equipped with to correct the problem.

“From that point on, the mixing auger would jump off the gearbox as you were filling the mixer. Then we had to climb inside to empty the mixer to reconnect the auger. This would take two guys two or three hours to do, and it happened as often as twice a day. At the same time, the mixer started to eat gearboxes. We had to put in a new gearbox nearly every six months at almost $1,000 a pop. I assumed the two problems were related but our dealer’s mechanic couldn’t find the problem. Finally, in the spring of ‘96, a sprocket went out. After two weeks, Gehl replaced it, along with a second sprocket matched to get the right speed on the auger. After that, the gearbox never wore out and the auger never jumped off the gearbox again. So it’s quite clear to me the problem was the mismatched sprockets put on by the dealer.

“All Gehl offered us for all our trouble was $1,000 off the price of a new 170 grinder/mixer, which lists for $17,000. But we put thousands of dollars worth of work in on the machine.

“We finally bought a new Farmhand, which is basically the same machine, for $11,000. We still have the Gehl.”

Best BuyWorst Buy

Ford F-350 pickup + 1 more

Lee Hostetler, Cottage Grove, Tenn. · Vol. 22, No. 2 (1998), p. 14

“We bought our 1996 Ford F-350 pickup last spring. It already has more than 65,000 trouble-free miles on it. I’m still driving a Ford F-250 pickup equipped with a 390 cu. in. engine that I bought 23 years ago. It still runs great and isn’t all rusted out like Chevy and GM models would be by now. “My worst buys are Goodyear tractor tires. They crack and fall apart before the tread is even worn down. Maybe they hold up better in other areas that have different soil types than ours.”

Best BuyWorst Buy

John Deere 9400 hoe drills + 4 more

Wayne Todd, Denton, Mont. · Vol. 22, No. 2 (1998), p. 14

Wayne likes his 1991 Deere 9400 hoe drills. “They work good and come with a transport hitch that’s well designed and easy to use. The metering is fairly accurate and seed placement is consistent. However, the single front wheel is too small for wet conditions. Also, the shanks around the pivot area should be built heavier. Otherwise, these drills are a pleasure to use.” His 1995 MK hydraulic drill filler heads his “worst buy” list. “It’s the worst piece of farm equipment I’ve ever owned. Installation is time consuming and difficult. The hydraulic foldup doesn’t have enough power to lift the auger and comes down way too fast. The electric solenoid valve that controls the auger doesn’t completely shut off the flow so the auger dribbles seed constantly. Another problem is that the latches on the cleanout doors are built too light. Also, the auger safety chain is too light and doesn’t stay hooked. I wish I had bought a Westfield or Brandt model instead.” “My 1982 New Holland TR 85 combine is also a worst buy. It’s probably the best overall designed and the most poorly engineered machine I’ve ever owned. It has adequate capacity for its size and threshes clean. It works well in nice, uniform, 40 to 50-bu. per acre wheat. However, it doesn’t take in heavy straw fast enough and it absolutely refuses to feed in lighter crops, particularly barley. The unloading system is too slow and is comparable to an old Deere 95. Also, the steering linkage is built too light, the hydraulics are marginal - particularly the reel speed control - and the sickle drive has problems. However, it’s an easy machine to operate and, under good conditions, saves more grain than some other brands. I’d probably buy another TR model hoping that the company engineers had learned a few things after this machine was built.”

Best BuyWorst Buy

Gleaner N5 combine equipped + 1 more

Dennis Kelsey, Connell, Wash. · Vol. 22, No. 2 (1998), p. 14

“My 1983 Gleaner N5 combine equipped with a 24-ft. grain head is my best buy. I ran it flat out in second gear in 83 bu. per acre white wheat and got only 1/10 of one percent dock-age at the elevator. One time I spent an entire day trying to find a shorted-out electrical wire. “My worst buy is my Haybuster 28-ft. sweep plow equipped with 36-in. sweeps. I bought it used in almost-new condition. I spent two days trying to adjust it, but I still couldn’t get it to penetrate untilled winter wheat stubble ground. My neighbor has a 36-ft. model that has no trouble penetrating the ground, even when the sweeps are set at their maximum penetration angle.”

Best Buy

Ram 250 pickup equipped

Edsel Salo, Watton, Mich. · Vol. 22, No. 2 (1998), p. 15

“My best buy is my 1992 Dodge Ram 250 pickup equipped with a Cummins diesel engine. It has plenty of power to pull my 26-ft. trailer and rides and handles great. “My 1977 Dodge 150 pickup equipped with a 318 cu. in. engine has been a trouble-free workhorse. I use it to pull the trailer, haul wood, and plow snow.”

Best Buy

Sunflower 4-section disk

Clarence Davenport, Callaway, Neb. · Vol. 22, No. 2 (1998), p. 15

A 1997 Sunflower 42-ft., 4-section disk rates as Clarence’s “best buy”. “It’s equipped with oscillating tandem axles that allow it to work smooth both in the field and in transport. It’s built heavy enough to stay in the ground where other disks would float up out of the ground, and it leaves the field level. It’s equipped with a convenient one-hand screw adjustment device on front for raising or lowering the disk, at 1/2 inch per turn. I’ve used it on 4,000 acres with no problems. Excellent workmanship. One disadvantage is that the transport width is 22 ft.”

Best BuyWorst Buy

John Deere 1219 mower-conditioner + 1 more

Don Berry, Spencer, Ind. · Vol. 22, No. 2 (1998), p. 15

Don’s pleased with his Deere 1219 mower-conditioner. “It does a good job. Excellent overall performance in a variety of forage crops and under some diverse and difficult conditions. “My 1993 Dodge Ram 250 pickup equipped with a V-8 engine and 5-speed manual transmission is my worst buy. It has weak springs at the front and rear and can haul only a half ton of feed. The rear end ratio is so high that I can’t even use it to pull my 16-ft. stock trailer. The dealer said he could correct these problems ‘at my expense’. What I wanted was a farm work truck - what I got is a toy that’s capable of an 85 mph highway speed while carrying two fishing poles and a small can of worms. I’ll probably buy another Dodge, but I’ll buy from a dealer who knows farm trucks.”

Best BuyWorst Buy

Vermeer round baler + 1 more

Don Scharff, Hartney, Manitoba · Vol. 22, No. 2 (1998), p. 15

“My 1975 Vermeer round baler is my best buy. It was almost trouble-free and is still being used by another owner. I used it to make about 2,000 bales a year when I had it. “My 1996 worst buy is my Cannon BJC 4100 printer. It quit working last June after it had printed only about 80 pages. It has a defective print head which the company won’t replace.”

Best Buy

Morton storage building

Lou Kocon, Jr., Oak Ridge, N.J. · Vol. 22, No. 2 (1998), p. 15

“My best buy is my 30-ft. wide, 55-ft. long, 12-ft. high Morton storage building. I can’t say enough good things about it or about the company people who sold it to me and put it up for me. I’ve had nothing but great service from everyone involved. The quality of the product, the workmanship that went into the construction, and the followup visit and inspection after construction was completed was nothing less than ‘top of the line’. I was so impressed that I’ve already had the company back to put an addition on this building, and in the near future I’ll put up a second Morton building which will be used as a workshop.”

Best Buy

Chevrolet S-10 extended cab pickup + 1 more

H.M. Roy, Middlebury, Ind. · Vol. 22, No. 2 (1998), p. 15

“My 1995 Chevrolet S-10 extended cab pickup is the best I’ve ever owned. It has 31,000 trouble-free miles. The 4.3-liter, 200 hp Vortec engine is very responsive and gets 22 to 24 mpg on the highway which I think is very good for a 4-WD. “I have a 1951 Deere A tractor that I bought 25 years ago and it still runs great. I think that with a little tender loving care these old tractors would last forever.”

Best Buy

DTN computer system

Pete Lamp, Fort Wayne, Ind. · Vol. 22, No. 2 (1998), p. 15

“I’ve been leasing my DTN computer system for four months and love it (ph 800 485-2238). It operates off a 30-in. satellite dish and has up-to-the-minute farm prices and information as well as futures prices. It also has up-tothe-minute weather information.”

Best Buy

Ford 1-ton 4-door pickup equipped

James Vaught, Norman, Okla. · Vol. 22, No. 2 (1998), p. 15

James is happy with his 1995 Ford 1-ton 4-door pickup equipped with a 460 cu. in. gas engine and 5-speed manual transmission with overdrive. “It has ample power for pulling heavy loads and a lot of cab room, and the two extra doors make it nice for transporting my crew. But what I like best is that it has a really smooth ride due to the extra long frame. No problems.”

Best BuyWorst Buy

John Deere 348 square baler + 1 more

William O. Parsell, Dover, N.H. · Vol. 22, No. 2 (1998), p. 15

William’s disappointed with his 1996 Deere 348 square baler. “I’ve had nothing but trouble with it since the third day after I bought it. It took more than one year and a lot of headaches to finally get it repaired. We got very little help from the company until we threatened to sue both the dealer and the company. It was finally repaired late last year.” On the “best buy” side, he lists his 1985 Ford TW5 4-WD tractor equipped with a cab, air conditioning, and heater. “It does everything we ask of it and is easy on fuel, easy to handle, and a joy to drive. It has a lot of power and the cab has good visibility.”

Best Buy

John Deere 8200 tractor + 1 more

Gary V. Koehler, Upper Sandusky, Ohio · Vol. 22, No. 2 (1998), p. 15

Gary’s satisfied with his 1997 Deere 8200 tractor. “I like everything about it except for the transmission which is a little jerky compared to the transmission on a Case-IH. Otherwise, it’s a joy to drive. “Our 1994 1-ton Chevrolet dually pickup is a joke. It doesn’t have enough power and gets only about 8 mpg. My semi truck gets better mileage than that.”

Best BuyWorst Buy

Case-IH 5140 tractor + 1 more

Boyd Cable, McAlester, Okla. · Vol. 22, No. 2 (1998), p. 15

“My 1992 Case-IH 5140 tractor is easy to operate and is my best buy. Everything on it works good. No problems. “My worst buy is my 1996 New Holland DMG 700 rotary mower. When a bearing went out the dealer put a new one in, but the same thing happened two more times.“ again. It works smooth and has a level built into the top of the handle which makes it easy to drill straight holes.”

Best Buy

DeWalt 15 amp chop

Donald Albright, Perkins, Okla. · Vol. 22, No. 2 (1998), p. 15

Donald’s likes his DeWalt 15 amp, 10-in. chop saw and 1997 DeWalt 3/8-in. heavy duty, variable speed, reversing drill. “I purchased the chop saw in 1996 and was so pleased with its performance that when I needed a hand drill I bought from DeWalt two engines, three bearings in the blade clutch, one catcher bag, and one gas tank.”

Worst Buy

Snapper walk behind

John Lawless, Albany, Ga. · Vol. 22, No. 2 (1998), p. 15

“My worst buy was my 1994 Snapper walk behind, self-propelled 5 hp lawn mower. I special ordered the mower because I wanted one with a blade clutch. The dealer was great but he had a bad product. The blade ‘scalped’ at any height, and the main frame flexed up and down like the old Kitty Hawk airplane. Also, the bagger would plug up whenever the humidity got above 50 percent. The dealer had to replace the engine uses a lot of oil. The dealer worked on the engine under warranty, but it still uses oil.”

Best Buy

Polaris 300 4-WD ATV

Dennis Huff, Donnybrook, N. Dak. · Vol. 22, No. 2 (1998), p. 15

A 1995 Polaris 300 4-WD ATV rates as Dennis’s “best buy”. “This machine hasn’t missed a beat since we bought it. We’ve already put 2,200 miles on it. We use it to fix fence, chase cattle, spray weed patches, and check grain fields. We use it every day for something. It’s the last piece of equipment I’d part with.”

Best BuyWorst Buy

Ram 3500 extended cab 4-wd + 1 more

Chris McCormick, Pleasantville, Iowa · Vol. 22, No. 2 (1998), p. 15

“I’m pleased with my 1997 Dodge 3500 extended cab 4-WD pickup equipped with a 5-speed transmission. It gets 14 mpg pulling a trailer and 20 mpg empty. It has a lock rear end so it can go places in 2-WD that the Fords we previously had would never go. It rides better than our car and has a lot of power. It’s an excellent pickup.” On the “worst buy” side, he lists his 1993 Belarus 925 front wheel assist tractor. “Whenever I tried using it to mow the pto went out. The first one went out at 50 hours, and we replaced a total of three ptos before we finally gave up. The air conditioner worked for only about 100 hours before it quit. The electrical system went bad, but luckily the local automotive electric shop had worked on other Belarus tractors with the same problem and was able to repair it. Now no one even wants to drive this tractor so it just sits. The only good thing about it is that we can pull start it when it’s cold.”

Best BuyWorst Buy

International Harvester Cub Cadet 2140 riding mower equipped + 1 more

Richard Harris, Hillsboro, Tenn. · Vol. 22, No. 2 (1998), p. 15

“My best buy is my 1997 International Cub Cadet 2140 riding mower equipped with a grass bagger. “It does a first class job of mowing our 2-acre yard, even in tall, damp grass. If I ever need another mower I’ll buy a Cub Cadet again. “My worst buy is my 1997 Simplicity riding mower equipped with a 14 hp Briggs & Stratton gas engine. It’s built too light and

Best Buy

Stihl chain saws

George Branscom, Queen City, Mo. · Vol. 22, No. 2 (1998), p. 15

George likes his two Stihlchain saws - a 1989 012 model equipped with a 14-in. bar and a 1991 026 model equipped with an 18-in. bar. “These chain saws can’t be beat for cleaning out fence rows, cutting firewood, or logging. I can use them all day without killing myself. They still have the original spark plugs. Even though they’re both several years old I wouldn’t sell them for what I paid for them.”

Worst Buy

Chevrolet 1500 pickup

Harry J. Griesemer, Bridgeport, Ill. · Vol. 22, No. 2 (1998), p. 15

Harry’s unhappy with his 1997 Chevrolet 1500 pickup. “When starting from the ‘stop’ position the pickup would shake and vibrate. The problem got so bad with a trailer behind that cups in the cab would shake right out of their holders. The dealer worked on it for three weeks but couldn’t solve the problem. He finally replaced the pickup with a 1998 model but it had problems, too. He had to install a new driveshaft because the original one was vibrating. I don’t think I want any more Chevrolets.”

Best Buy

Mercury Marquis + 5 more

Donald R. Miller, Dongola, Ill. · Vol. 22, No. 2 (1998), p. 15

“My 1991 Mercury Marquis is a good car. “My 1985 Hesston 5510 big square baler is the most trouble-free piece of machinery I’ve ever owned. “My 1972 Chevrolet pickup is still going strong after 25 years. My 1988 Chevrolet pickup equipped with a 4.3 V-6 engine also works good. “Other best buys include my Homelite XL12 chain saw, New Holland 273 small square baler, and 1964 Allis-Chalmers D17 tractor.”

Best Buy

John Deere max-emerge

Daryl Dirks, Scott City, Kan. · Vol. 22, No. 2 (1998), p. 15

“Everything on it is well designed,” says Daryl about his 1996 Deere Max-Emerge II 8-row planter. “It does an excellent job of planting. It spaces seeds so evenly that at low dryland populations it looks like the corn rows run in two directions.”

Best Buy

Agco White 6065 tractor

Mitchell Hovell, Seymour, Wis. · Vol. 22, No. 2 (1998), p. 15

Mitchell likes his 1995 Agco White 6065 tractor. “It’s a handy loader tractor, and we also use it for planting, cutting hay, and blower work. It’s fun to drive and we haven’t had any problems with it.”

Best Buy

Harold owns a 1996 Vermeer 505I baler

Harold E. Johnson, Dupree, S. Dak. · Vol. 22, No. 2 (1998), p. 15

Harold owns a 1996 Vermeer 505I baler. “It makes good bales and operates okay. However, it does have some ‘bugs’ in it that we don’t like. We bought it equipped with an optional ramp that’s supposed to roll the bale backward during unloading, eliminating the need for the tractor driver to back up. However, we found it didn’t work well and was a nuisance so we removed it. Another problem is that there’s no way to release belt tension.”

Best BuyWorst Buy

Ford F-350 pickup equipped + 1 more

Mark Malsam, Hugo, Minn. · Vol. 22, No. 2 (1998), p. 16

Mark’s impressed with his 1995 Ford F-350 pickup equipped with a power stroke diesel engine. “It runs well, gets 17 to 20 mpg, and has enough power to pull my trailers. I’ve put more than 40,000 miles on it with no problems. It sits outside sometimes in the winter but always starts. “My worst buy is my 1993 Polaris 350 ATV. The engine backfires and blows the muffler off whenever I let up on the throttle. It’s also hard on fuel. I had to bore out the engine with only 500 miles on it.”

Best BuyWorst Buy

John Deere 220 stalk shredder + 1 more

Dick A. Hufford, Morris, Minn. · Vol. 22, No. 2 (1998), p. 16

Dick’s the owner of a 1997 Deere 220 stalk shredder. “It works well and does a nice job. It runs much smoother than our old Deere 27 model. It does take a lot of power to pull it, though.” On the “worst buy” side, he lists his 1997 Shurlock Jr. roll tarp that’s designed to fit gravity wagons and grain carts. “We installed it on our Ficklin grain cart and it’s a joke. The end flaps are designed to be held down by tarp straps. However, when the straps are unhooked they catch on everything as the tarp is being rolled up. And when I try to unroll the tarp, the straps hook each other so I have to crawl up on the wagon to unhook them. Believe me, you only try this once.”

Best BuyWorst Buy

Jeep Commanche 2-WD pickup + 1 more

Keith King, Kincardine, Ontario · Vol. 22, No. 2 (1998), p. 16

Keith’s “worst buy” was his 1989 Jeep Commanche 2-WD pickup. “I should’ve known that I was in for a rough ride when the oil pan rotted out and the seals went out on the rear axle before the truck was even two years old. At about 40,000 miles the syn-chronizers started to go out in the transmission.

“Shortly after the power train warranty had expired, the valve lifters started to rattle in the engine. At about 60,000 miles I put new brakes on the truck. None of the parts were available from a jobber so I had to buy all the parts from Chrysler. The front rotors cost me $100 apiece and the total brake job cost almost $700. The real killer, though, was when the sides on the bed started to rust out. It was a nightmare trying to get Chrysler to back up its 7-year/100,000 mile rust perforation warranty.

“I drove the truck for seven years and put 84,000 miles on it before trading it in on a 1996 Ford F-150 4-WD. The Ford dealer allowed me $650 for the Jeep and I can’t blame him.”

Best BuyWorst Buy

White 6105 front wheel assist + 4 more

Kevin Brunello, Hurley, Wis. · Vol. 22, No. 2 (1998), p. 16

“My 1997 White 6105 front wheel assist tractor is my best buy. It has a nice smooth transmission, starts excellent even in cold weather, and pulls through the muddiest part of my feedlot without even spinning a tire. The cab has a lot of glass so I have a great view when doing loader work. The Westendorf TA-28 loader on it is also a best buy. The main loader booms are low enough that they don’t interfere with my vision.

“My 1996 GM Sierra 4-WD shortbed pickup is a best buy. It has never failed me after 25,000 miles. Our last two winters have been very fierce with a lot of snow and cold, but the 305 cu. in. Vortec engine always started right up even though we never used an engine heater or parked it inside a building. I think GM and Chevy make the best pickups on the market.

“My worst buy is my 1981 Deutz DX90 front wheel assist tractor. One problem was that it starts hard in cold weather. The engine has a lot of power - Deutz engines are built strong and you can expect many years of use out of them. I also had a lot of problems with the front part of the power train which cost me a lot of down time and money. On the positive side, the Westendorf WL44 loader that came with it has been trouble-free. This company makes the best front-end loaders on the market.”

Best Buy

Bobcat 743 skidsteer loader

Earl R. Miller, Middlebury, Ind. · Vol. 22, No. 2 (1998), p. 16

“My only complaint is that it starts hard in very cold weather,” says Earl, who otherwise is pleased with the 1989 Bobcat 743 skidsteer loader that he bought used in 1993. “It’s equipped with a Kubota diesel engine which has a lot of power and is easy on fuel.”

Best Buy

Case 1390 tractor equipped + 2 more

Pat Kenneoy, Bellevue, Texas · Vol. 22, No. 2 (1998), p. 16

Pat’s Case 1390 tractor equipped with a front-end loader heads his “best buy” list. “It’s the most powerful little tractor I’ve ever owned.

“My International 966 tractor, which I bought used five years ago, is a best buy. It’s equipped with a cab and air conditioning which makes it a pleasure to drive when baling hay.

“My 1989 Dodge Dakota pickup equipped with a 3.9 cu. in. 6-cyl. engine has 128,000 trouble-free miles on it and is a best buy. My 1986 Dodge Ram 250 equipped with a 360 cu. in. engine has 75,000 miles on it. I use it only to pull my livestock trailer and also for general work around my farm. The Dakota gets about 20 mpg while the Ram gets about 13 mpg. Both have been trouble-free.”

Best Buy

New Holland 1411 discbine

Harry Nolt, Orchard, Iowa · Vol. 22, No. 2 (1998), p. 16

“My 1996 New Holland 1411 discbine and 1996 New Holland 644 “Silage Special” round baler are both best buys. The discbine will cut through any kind of hay. I really like the endless belts on the baler. Heavy, wet silage bales can test the lacers on other balers. I also like the Autowrap tieing system - it makes bales that are all the same size.”

Best Buy

Ram 3/4-ton 4-WD pickup equipped

D. LeRoy Wikert, Emmetsburg, Iowa · Vol. 22, No. 2 (1998), p. 16

“It rides almost as good as a car and is fuel efficient,” says D. LeRoy about his 1996 Dodge 3/4-ton 4-WD pickup equipped with a diesel engine. “It gets 15 to 20 mpg depending on the weather and use, and it turns short. I like being able to put it in 4-WD onthe-go at speeds up to 70 mph.”

Best BuyWorst Buy

Kubota 5030 4-WD tractor equipped + 1 more

Bennie Eugene Street, Lynnville, Tenn. · Vol. 22, No. 2 (1998), p. 16

Bennie nominates his 1994 Kubota 5030 4-WD tractor equipped with a front-end loader as his “best buy”. “I use it just about every day. It’s the handiest piece of equipment I have. It works good on hills. I use the loader to do everything from stacking hay to hauling, digging, and loading dirt and rocks, etc.

“My worst buy is my New Idea disc mower. One or more of the shafts that drive the line of discs ‘rounds off’ about every 20 to 30 acres. I told the dealer and the company rep about this problem but got no help at all. One mechanic said something was out of line, but no one will do anything about it so I have to tear it down and replace one or more of the shafts myself. I plan to get rid of this mower as soon as I can. I’d never buy another one like it.”

Best Buy

Ram 350 pickup equipped + 1 more

Wayne E. Stamm, Monroe, Wis. · Vol. 22, No. 2 (1998), p. 16

“My 1991Dodge 350 pickup equipped with a 5.7-liter Cummins engine does everything I ask it to do. I use it to pull a 5 to 6-ton trailer with no problems and can haul loads weighing up to 8 tons. It has more than 105,000 miles. I’m well satisfied with it.

“The 5-speed transmission on my 1990 Dodge Dakota pickup went out twice in about eight months when the pickup had about 103,000 miles. Otherwise it’s a good pickup. The 4-cyl. engine is fuel efficient.”

Best Buy

Polaris Explorer 500 4-WD atv + 2 more

Mervin E. Dokken, Roseau, Minn. · Vol. 22, No. 2 (1998), p. 16

“My 1997Polaris Explorer 500 4-WD ATV is my best buy. It always starts right up. No problems.

“My 1954 Allis Chalmers WD 45 tractor still runs like new. Over the years I’ve spent very little money on it.

“My 1988 Oldsmobile has more than 105,000 trouble-free miles and gets more than 30 mpg on long distance trips. It still drives and handles like new.”

Best Buy

DeWalt 4 1/2-in angle grinder-sander + 1 more

Oliver Nowotny, La Vernia, Texas · Vol. 22, No. 2 (1998), p. 16

Oliver’s “best buy” is his DeWalt 4 1/2-in. angle grinder-sander which operates on 110 volts and turns at 10,000 rpm’s. “It works like a charm for all but the heaviest grinding jobs. I can use the sanding disc to cut thick plexiglass, and the wire scratch wheel does a good job of cleaning slag from welds.

“My Milwaukee 9-in. angle grinder (110-volt, 5,000 rpm’s) is a bit heavy to handle but removes metal fast.”

Best Buy

Ram 2500 extended cab pickup + 1 more

Gerald Karas, Massena, Iowa · Vol. 22, No. 2 (1998), p. 16

Gerald likes his 1997 Dodge 2500 extended cab pickup equipped with a turbocharged diesel engine. “Last winter we used it to pull a 35-ft. fifth wheel trailer to Arizona and Texas. It averaged anywhere from 10 mpg in a head wind to 16 mpg in ideal conditions. We pulled it in fifth gear all the time except when we had to downshift in the mountains. The rear axle has a 3:54 ratio. It rides really nice and gets 20 to 26 mpg empty.

“We previously used our 1991 Ford 250 Lariat pickup powered by a diesel engine to pull the same trailer, but it never got more than 10 1/2 mpg even though the engine was turbocharged. This pickup had a lot of problems. The company worked it over twice but the transmission still was noisy and vibrated. There were also problems with the cruise control, axle seals, glow plugs, electric door locks, and more. I traded it in at 18,000 miles for the Dodge. Good riddance.”

Best BuyWorst Buy

John Deere 9400 4-WD tractor equipped + 1 more

Marvin Mechtel, Page, N. Dak. · Vol. 22, No. 2 (1998), p. 16

Marvin’s the satisfied owner of a 1997 Deere 9400 4-WD tractor equipped with triple wheels. “I love to drive it. It has a lot more pulling power than the company’s previous 8970 model. I used it last year to pull a 54-ft. chisel plow and it used only 1/2 gallon per acre of fuel. I can hardly believe that much power can be delivered on such little fuel.”

On the “worst buy” side, “My Deere 730 air drill was a nightmare to use. Anywhere in the field that was a little wet the discs would mud up, causing them to slide along which left seed on top of the ground. I traded it for a Deere 1850 no-till air drill. It never muds up and seeds equally well in conventional or no-till. I love it.”

Best Buy

Chevrolet Suburban

Michael R. Lammers, Leipsic, Ohio · Vol. 22, No. 2 (1998), p. 16

“We’ve put more than 80,000 miles on our 1992 4-WD Chevrolet Suburban with only a few problems - the radiator started leaking and the windshield wipers quit working. Otherwise, no problems. It gets 17 to 18 mpg which I think is great for a vehicle its size. My wife coaches a girl’s basketball team and often uses the Suburban to haul the girls around. The team calls it a ‘land yacht’”.

Best Buy

Ford pickups

Larry Twidwell, Hershey, Neb. · Vol. 22, No. 2 (1998), p. 16

Larry’s pleased with his Ford pickups. “I had two 1977 F-150 models. One went 267,000 miles and only had the bands tightened once in the automatic transmission. The other one went 192,000 miles with no problems. I had a 1986 model with 99,000 miles on it when I traded it for my current 1994 Ford F-250 XLT extended cab 4-WD pickup. It’s equipped with a 460 cu. in. V-8 engine, 4:10 rear end, and 4-speed automatic transmission. It’s by far the best pulling, riding, and driving Ford pickup I’ve ever owned. It gets 14.8 mpg on the highway and 10.6 mpg pulling a 35-ft. camper followed by a 20-ft. boat. It handles a 24-ft. livestock trailer with ease. I can’t say enough good things about it. No problems after 35,000 miles.”

Best Buy

Uni-Hydro 85-ton Iron Worker

Karl Retzlaff, Morris, Minn. · Vol. 22, No. 2 (1998), p. 16

Karl likes his Uni-Hydro 85-ton Iron Worker (MLM Enterprises, 13307 525th Ave., Cosmos, Minn. 56228 ph 320 737-7975). It’s an expensive machine, but if you have a busy farm shop an iron worker can really help in cutting, punching, and bending steel. I use it constantly in my shop and get good service on punch and die replacements. It has a lot of power, is easy to operate, and saves acetylene and oxygen costs when cutting metal. I wish I’d had it years ago. It’s a great machine.”

Best Buy

MTD 2185 riding mower

W.A. Dostal, Ossian, Iowa · Vol. 22, No. 2 (1998), p. 16

“My 1997 MTD 2185 riding mower is neither a best nor worst buy. It’s equipped with a foot-operated hydrostatic shifting system which my wife can operate without having to use her left foot/knee. She has a man-made knee which isn’t as flexible as the original. One problem with this mower is that it’s almost impossible to open the oil drain plug due to its position on the engine case. The plug is located just above the engine frame mount and is too close to the frame for me to install a drain hose on it. As a result, oil drains all over the engine frame, steering linkage, and onto the floor where it makes a big mess. It’s impossible to catch the oil because it follows the steering linkage.

“The company says the oil should be sucked out through the dipstick tube, but that would leave a lot of used oil in the crankcase. Another problem is that it’s almost impossible to grease two zerks at the bottom of the steering column. The zerk’s position makes it almost impossible to fit the grease gun onto the zerk and make it hold.”

Worst Buy

MTD 5 hp chipper/shredder

Donald G. Husek, Ritzville, Wash. · Vol. 22, No. 2 (1998), p. 17

Donald’s impressed with the service provided after he had problems with his MTD 5 hp chipper/shredder. “Some welds cracked on the bottom side of the chute that’s used to feed branches in. I wrote a letter to the company. They didn’t write back back but instead sent me a new chute at no cost.”

Best BuyWorst Buy

Case-IH 8840 windrower + 1 more

Kurt Schroeer, Perham, Minn. · Vol. 22, No. 2 (1998), p. 17

“I’m impressed with my 1997 Case-IH 8840 windrower which I bought used with 600 hours on it. It drives and handles well and cuts clean and fast. It also has a comfortable and quiet cab. Everyone in my family wants to cut hay now.”

On the “worst buy” side, he’s had problems with his 1996 Gehl 1265 forage chopper. “It’s equipped with electronic sensors that are supposed to regulate the chopper and shut it down if something plugs up or if any shafts slow down too much. However, the sensors never have worked. Since day one we’ve had to use a manual bypass switch. The dealer’s mechanic told me that most of these sensors fail within one year. The chopper itself runs well and has a lot of capacity. But the electric gismo’s on it belong on the rockpile.”

Best Buy

M & W 4590 round baler equipped

Charles Snapp, Cynthiana, Ky. · Vol. 22, No. 2 (1998), p. 17

“I’m well pleased with my M & W 4590 round baler equipped with a plastic wrap attachment. I find that the quality of plastic-wrapped hay stored outside is as good as square bales stored in a barn. Very little hay is wasted during storage because the only loss is what touches the ground. I store the bales on a rock bed in order to minimize losses. Another advantage is that plastic-wrapped hay doesn’t develop a musty smell as do non-wrapped round bales. The round bales have a soft core which is probably why cows prefer these bales over square bales. I made an unloader to handle the soft core satisfactorily. The body condition of my cows has improved since I started feeding the wrapped bales two winters ago.”

Best Buy

Morris Maxim air drill equipped

Murray Clarke, Rosetown, Sask. · Vol. 22, No. 2 (1998), p. 17

“Its accuracy and simplicity make it an excellent seeding outfit,” says Murray, impressed with his 1996 Morris Maxim air drill equipped with a 7180 seed tank. “This drill is easy to set for both seed rate and machine level. The 60/40 split cart has a walk-through design with ladders on both sides that make it easy to fill.”

Best Buy

Agri Speed automatic wagon hitch

Dale V. Grahl, Eden, Wis. · Vol. 22, No. 2 (1998), p. 17

“One of my best buys ever is my 1997 Agri Speed automatic wagon hitch (Bergman Mfg. Inc., Box 82, Arthur, Iowa 51431 ph 800 551-4554 or 712 675-4733). “It eliminates the need to constantly get on and off the tractor in order to hook up and unhook wagons. I have a disease that makes it hard to get on and off tractors. Now it’s fun to run my forage chopper again.”

Best Buy

Bush Hog

Dudley Adams, Union, S.C. · Vol. 22, No. 2 (1998), p. 17

“When I bought my 10 1/2-ft. wide Bush Hog it cut my bush hoggin’ time in half compared to the 6-ft. model that I had been using. It also reduces fuel usage and wear and tear on my tractor. I use a 52 hp Massey Ferguson 255 tractor to pull it.”

Best Buy

MT Housing

Eva McLelland, Goshen, Ala. · Vol. 22, No. 2 (1998), p. 17

“I would like to caution anyone ordering a low-cost modular house from MT Housing in Yakima, Wash., to be careful about sending too much money to the company before receiving the unit. I read an article in FARM SHOW about their low-cost housing units which are made out of ocean-going cargo containers. I ordered a unit in July, 1997 and sent them a check for $5,886 in August and another for $11,398 in September. After that I couldn’t get them to deliver it. They kept telling me it would ‘come next week’ but it didn’t. We went back and forth and they had lots of excuses. I finally asked for my money back but they wouldn’t refund it. They finally shipped the house to me in February.

“I am 82 years old and legally blind and the money for this house represented much of my life savings. This was a tramatic experience for me. I should never have sent the money before shipment. The house itself is okay but not everything is set up the way I requested.”

Best Buy

Morton + 2 more

Warren Lathe, Brattleboro, Vt. · Vol. 22, No. 2 (1998), p. 17

Warren likes his 1996 Morton 54-ft. by 75-ft. building. “It’s attractive and well-constructed with no obstructions or pillars inside which makes it easy to move equipment. I have a sawmill inside that’s opposite a large set of double doors. With the doors open it’s like the sawmill is out in the open - there are no dark areas. The building is equipped with large skylites which add more light.

“My best buy of all time is my Sears Craftsman 300 amp AC welder which I bought in 1950. It was expensive at that time. However, I’ve used it to weld large trailers and all sorts of things over the years and it’s still purring away like new. I wanted to be able to weld out in the field so in 1975 I bought a Lincoln AC-DC unit with 6,000-watt auxillary power. Both welders are best buys. They’re ready for action any time.”

Best Buy

E-Kay hydraulic bin sweep + 1 more

Duncan Brock, McTaggart, Sask. · Vol. 22, No. 2 (1998), p. 17

Duncan’s impressed with his E-Kay hydraulic bin sweep (E-Kay Enterprises, Sedgewick, Alberta). “It’s advertised as a bin sweep that you can use either on your auger or mounted inside the bin to fill an under-floor auger. The company says it won’t climb a pile of grain and that its curved back allows it to clean right down to the floor while you stand outside the bin and out of the dust. Well, it works like they said. We think it’s the best sweep we’ve ever used.

“We’re reasonably pleased with our 1993 Deere 9600 combine but wonder why Deere made two design changes on it. We had a 1990 Deere 9500 model that had an easily adjustable control panel that you moved up and down by simply moving a spring-loaded pin. It also was equipped with a beater grate with two spring-loaded pins that made the grate easy to raise and lower. However, on the 1993 model they changed the design on both of these items which makes for two gruesome, time-consuming jobs. Another problem is with the metric nuts and bolts they use. They are odd-size metric sizes that most companies don’t use - 13 mm, 15 mm, 18 mm, and 21 mm. It seems odd to me that a company that’s supposed to be so interested in its customers would strive to give you less for more money and then add to your grief with all these funny-sized bolts and nuts.”

Best Buy

John Deere 7810 MFWD tractor equipped + 3 more

Larry McGill, Glencoe, Ontario · Vol. 22, No. 2 (1998), p. 17

Larry’s impressed with his 1997 Deere 7810 MFWD tractor equipped with a power quad transmission. “We traded in a 10-year-old Case-IH 2294 tractor equipped with front wheel assist and powershift transmission. It was reliable and fuel efficient but had a long turning radius and a transmission that was difficult to shift between gear ranges. The 7810 turns short, shifts effortlessly between ranges, has a lot of power, and is fuel efficient.

“My 1993 Thurston Blue Jet Landtracker coulter caddy is one of the heaviest and best built on the market, but the 900 series coulters on it wear out too fast at the pivot point. The axles and pivot bushings went out after I used it on only 4,000 to 5,000 acres, causing the coulters to track poorly. Also, the company doesn’t make left and right side coulter assemblies which are required for better residue flow. I replaced 27 coulters with ones made by Till-Tech (RR 5, St. Thomas, Ontario N5P 3S9 ph 519 775-2405). This company offers left and right coulters that are larger in diameter and have longer pivot axles and bushings. The coulters are also equipped with an adjustable 2,200-lb. spring. They should last a long time.”

Best BuyWorst Buy

Gerber multi-plier pocket tool + 1 more

James D. Teeter, Clarksville, Tenn. · Vol. 22, No. 2 (1998), p. 17

“The one tool that I can’t live without is my Gerber Multi-plier pocket tool. I can use it to fix just about any small problem. The pliers can be opened and closed with one hand - it’s almost an entire toolbox in one hand.

“The hydraulic reversing transmission I bought for my 1997 Deere 5400 MFWD loader tractor is really not as much a “worst buy” as a case of overanalyzing on my part. We use the tractor primarily for loading sawdust and wood in dark-fired tobacco curing barns. ‘Dusting’ these barns gets pretty rough on your clutch leg so we ordered the optional hydraulic reversing transmission. This decision turned into a $2,500 mistake. The tractor and transmission work fine, but working in close quarters is made more difficult with the hydraulic reverser. We made a snap decision without trying out the new transmission before we ordered it. Next time we buy a 5400 we won’t order the reverser option.”