Milwaukee 1/2-in impact wrench
What FARM SHOW readers say · 6 Best Buys1 Worst Buy · Power & Hand Tools
Milwaukee 1/2-in impact wrench
6 Best Buys1 Worst BuyEdwin’s impressed with his 2019 Pequea Plantmaster 614 6-row corn planter (ph 717 442-4406; www.pequeaplanter.com). “I like how they patterned this planter after a Deere 7200 model, but borrowed ideas from other brands as well. The planter is less than 14 ft. wide going down the road. I’d recommend it to anyone.
“I don’t think I could operate our farm without our Milwaukee 1/2-in. impact wrench. We’ve had good luck with all our Milwaukee power tools.”
“My Milwaukee 1/2-in. cordless impact wrench saves time compared to using an air-operated tool. I just squeeze the trigger and go. It’s one of my favorite tools.”
“I own many DeWalt cordless tools and like them. However my son recently bought a new Milwaukee 1/2-in. impact wrench, and we’re amazed at how much power it has.”
“I’ve had good luck with my 2018 Milwaukee 1/2-in. impact wrench, a high torque model that’s rated at 1,000 ft. lbs. It can easily handle lug nuts on pickups and tractors, and even on semi trucks. It comes with 2 batteries that last a long time. It also has an excellent warranty.”
“My Milwaukee 1/2-in. high torque impact wrench delivers up to 1,100 ft.-lbs. of nut-busting torque.
“I started using Schaeffer’s Specialized Lubricants engine and gear oil in my bulldozers and track loaders way back in 1960 and have used it ever since (www.schaefferoil.com; ph 800 325-9962). The first bulldozer I used it on was a Cat D4. I’ve also used it on Cat D2 and D4C dozers; on Komatsu D37E, D41-P, and D51 dozers; and on an 850E track loader – and I’ve never had an engine failure on any machine.”
Lowell’s “worst buy” is his Milwaukee 1/2-in. hammer drill equipped with a German-made Rohti chuck. “Even with only average use the Rohti chuck will fail. Sears, DeWalt, Bosch and others have all used this same chuck. It won’t hold tight on bits and will rapidly deteriorate in performance until it fails totally. I’ve used this chuck on several different brands of hammer drills. I wrote to several of the manufacturers but got no response.
“While working in a feed mill a few years ago, I had occasion to use a Black & Decker no. 8 nibbler to cut 12-ga. (almost 1/8-in. thick) stainless steel sheeting. Stainless steel is just about the toughest metal to cut. The tool would break after one 4 by 8-ft. sheet. I knew I had to do something to keep the owner of the mill from quitting the project. So I decided to use copper bearing anti-seize compound on the bottom side of the sheet, where I would be cutting. I used heavy gear oil to cover the cut-mark on top, so I could still see the pencil mark. With this simple change I was able to extend the life of the tool greatly. At $85 a set this was an exceptional improvement.”
“I like my new Milwaukee 1/2-in., 14.4-volt cordless drill-driver. I bought it to replace an old Makita cordless drill. The batteries last a long time before they have to be recharged. One time I accidentally dropped the drill from about 10 ft. up an extension ladder. It bounced off the bench and onto the concrete floor, but still ran fine.
“My 1999 Swischer 60-in. pull-type mower worked good for cutting very thin grass, but it wouldn’t work under normal mowing conditions. Even with sharp blades and good belts it would windrow the grass, no matter how slow I mowed with it. The deck design was too square and had no curve to it, which prevented the grass from being discharged well.”
Own a Milwaukee? Tell FARM SHOW how it’s held up.
Your report could appear in a future issue.