Real farmers rate what they bought, from FARM SHOW MagazineSubscribe  ·  Free issue  ·  Send us your Best or Worst Buy
Subscribe to FARM SHOW
Home › Issues › Vol. 18, No. 3 (1994)

Best & Worst Buys: FARM SHOW Vol. 18, No. 3 (1994)

48 reports from pages 14–16 · 43 Best Buys9 Worst Buys · See everything in this issue at FARM SHOW →

Best Buy

Yamaha

Ed Staudt, Vibank, Sask. · Vol. 18, No. 3 (1994), p. 14

Ed Staudt, Vibank, Sask.: Ed’s had trouble j SE with his Belarus Don 1500 combine. “It should have been painted lemon yellow. After it arrived, the company had to bring outthree sets of sieves, both top and bottom, before we found a set that was close to acceptable. Other problems included leaking hydraulic hoses and hydraulic block assemblies, and an erratic fuel gauge. Some monitors didn’t work, while others wouldn’t shut off, setting off an ear-splitting alarm in the cab. We couldn’t raise the header because of a stuck solenoid and the unloading auger wouldn’t swing out. “After dealer and factory technicians made many trips to our farm, the combine was supposed to be field ready. However, it never worked properly. The alarm would sound, even when the combine wasn’t running. The unloading auger would swing out and start unloading grain for no reason while we were driving. Sometimes the radio would work, sometimes the air conditioner would work, sometimes the hydraulics would work, but never did everything work together for more than a 7-hour shift without a breakdown of some kind. “Other problems included tailing sieves falling out, the turbo charger going up in smoke, and the unloading auger burning up ominate t Buys belts. Belarus technicians found that five of the six fuel injectors were faulty and they replaced a number of hydraulic valves because of faulty O rings or fittings, A weld on the shaker arm that oscillates the cleaning mechanism broke, causing idler arms to break off. Brazing fell off the injector tubes in the engine compartment with great frequency. One time, when the brakes seized, we had to back up for a while until they let go and we could drive forward again. “We finally got the company to take the combine back and reimburse some of our money (they expected us to pay for the hours we puton the combine, although most of those hours were spent driving to the shop to repair or weld something). We wouldn't buy another Belarus.” Ralph McLaughlin, Blackstock, Ontario: Ralph nominates his 1993 Yamaha Big Bear 4-WD ATV as his “best buy”. “I use it to tow a large trailer. Performs well inall weather and soil conditions and always starts. I'd reccommend Yamaha to anyone in the market for an ATV.”

See this page at FARM SHOW →
Best BuyWorst Buy

Kubota M6950 + 3 more

John Tibben, Kincardine, Ontario · Vol. 18, No. 3 (1994), p. 14

John Tibben, Kincardine, Ontario: John’s the satisfied owner of a 1993 Cheyrolet 3/4-ton 4-WD pickup equipped with a 6.5-liter turbocharged diesel engine. “It has lots of power and gets excellent mileage on long trips - about 25 mpg on the highway and 20 to 21 mpg around town, It rides like a car and is nice and quiet. Starts right up even in the coldest weather. “My 1989 Kubota M6950 DT tractor isn’t really a worst buy because it does everything we want it to and starts good in winter. However, parts for it are expensive. For example, a simple work light switch sells for $73. Another problem is that it’s hard to service. You need the fingers of a newborn baby to work in some of the cramped spaces. “My Deere 530 and 535 round balers have both been best buys. I made 15,000 bales with the 530 before I traded itin for the 535 and I made 17,000 bales with it before trading for a new 535 equipped with net wrap. We'll see how well the new one works. Ido some custom baling and a lot of people ask for these balers. They make tight bales that do a good job of shedding water. Net wrap should help even more.” James Greer, Gorrie, Ontario; James's 1992 Case-IH 8520 in-line square baler heads his “best buy” list. “I've used it to make over 40,000 bales with little downtime. It can make up to 400 bales per hour with minimum leaf loss because it has a low pickup height and because hay doesn’t get handled as much before being tied because there's no cross auger. It makes firm, square bales that truckers really like, “Two years ago I bought a Harco 45-ft. bale elevator. It’s well-built and should last a long time. My only complaint is that it’s too heavy to be easily moved around. To solve the problem I had a friend mount a wheel under the front of it.”

See this page at FARM SHOW →
Best Buy

John Deere 111

Barry Denison, Metcalfe, Ontario · Vol. 18, No. 3 (1994), p. 14

Barry Denison, Metcalfe, Ontario: "My New Idea 483 round baler is a best buy. We've made more than 8,000 bales with it and the only thing we've replaced is a Vbelt on the pickup. For the price we paid it’s a hard baler to beat. “My 1989 Deere 111 riding mower ran great the first year until the warranty expired. Then the engine went bad and the company wouldn't do anything about it. I went through two engines in three years before I traded it off.”

See this page at FARM SHOW →
Best Buy

Avery Huneycutt, Inman, S

Avery Huneycutt, Inman, S.C. · Vol. 18, No. 3 (1994), p. 15

Avery Huneycutt, Inman, S.C.: “My 1982 Mazda B2200 diesel truck is a heavyduty work truck with no unnecessary bells and whistles. It’s stable and well-balanced so the front and rear tires wear at about the same rate. It has 165,000 miles and has been almost trouble-free. I added bed tie-downs and a ladder rack. Too bad they don’t build new trucks like this one.”

See this page at FARM SHOW →
Worst Buy

Paul Singleton, Bruceville, Ind

Paul Singleton, Bruceville, Ind. · Vol. 18, No. 3 (1994), p. 15

Paul Singleton, Bruceville, Ind.: Paul likes his Big Husky automatic cattle waterer. “It performed flawlessly during the “Too bad they don't build new ones like this one.” coldest winter on record. It’s easy to install, adjust, and clean, and it’s well-insulated. Uses an 80-watt element that hardly ever comes on. “My Audiovox fender-mount radio is my worst buy. It didn’t work right from the start. It has poor reception and a cheap speaker. The FM band went out so the dealer sent the radio in to be repaired. After itcame back it worked for only a half day.”

See this page at FARM SHOW →
Best BuyWorst Buy

Nissan + 2 more

Murray Woods, Linden, Alberta · Vol. 18, No. 3 (1994), p. 15

Murray Woods, Linden, Alberta: A 1985 Nissan Kingcab truck equipped with a powershift transmission heads Murray's “best buy” list. “It has over 150,000 miles with only normal maintenance. The only modification made was to install a carburetor kit. It still runs great. “My 1986 Deere 4650 tractor is reliable and hasn't had any problems. It has a quiet cab with a comfortable operator platform.” On the “worst buy” side, “One year ago we bought a new Chrysler mini-van, The van works great but the Goodyear tires on itarea joke. Within 2,500 miles the sidewall blew outon one tire and within 12,000 miles the other three tires wore out, Chrysler said the tires weren't their responsibility and sent me to Goodyear. Goodyear indicated these were ‘cheap’ tires and wouldn’t back them. I'm disappointed that Chrysler and Goodyear would endanger their reputation and the safety of customers by putting such poor tires on a new vehicle.”

See this page at FARM SHOW →
Best Buy

Chevrolet 1/2ton

Stanley Byerly, New Salisbury, Ind. · Vol. 18, No. 3 (1994), p. 15

Stanley Byerly, New Salisbury, Ind.: Stanley nominates his 1972 Chevrolet 1/2ton pickup equipped with a 402 cu. in. engine and TH400 transmission as his all time “best buy”. “It has 210,000 miles on it and the only work done to the engine was last year when I installed new valves and a new timing chain and gear, I’ve used it to pull heavy trailer loads over long distances. Itstill has the original engine, transmission, rear end, and front suspension. It’s been repainted twice. The truck cost $4,500 fully loaded when I bought it, not including air conditioning. The same pickup today would sell for $20,000 without the same quality.”

See this page at FARM SHOW →
Best Buy

John Deere 328

Jason Starnes, Salisbury, N.C. · Vol. 18, No. 3 (1994), p. 15

Jason Starnes, Salisbury, N.C.: “It makes the best bales I've ever seen,” says Jason, owner of a 1993 Deere 328 baler. “Bale shape, size, and density stay the same regardless of windrow size. The baler’s wide pickup makes iteasy to getall the crop. It runs quiet and smooth and is easy to service. It’s also easy to clean up at the end of the season.”

See this page at FARM SHOW →
Best Buy

Lloyd J

Lloyd J. Drees, Fontanelle, Iowa · Vol. 18, No. 3 (1994), p. 15

Lloyd J. Drees, Fontanelle, Iowa: “I'm well-pleased with my 1991 Belarus 925 tractor. had some trouble with hydraulics, but the dealer finally took care of the problem. It still leaks some oil but the tractor works great and is fuel efficient. It has a good air conditioner and heater. Considering the low price, it’s a real bargain.”

See this page at FARM SHOW →
Best Buy

John Deere 6400 + 2 more

Leo Mugan, Mitchell, Wis. · Vol. 18, No. 3 (1994), p. 15

Leo Mugan, Mitchell, Wis.: “My Deere 6400 tractor equipped with a cab and power quad transmission is my best buy. It’s the neatest, handiest, most comfortable tractor I've ever owned with some real improvements over older models, including the ability to be refueled from the ground, an improved transmission, and a smokeless, gutsy engine.” Floyd Hartke, Dieterich, HL; “I bought my best buy 1987 Case-IH 4694 tractor used with 800 hours on it. After 1 put on about 200 hours, a tooth chipped off the timing gear. Even though I bought it used, the company still paid for most of the repair.”

See this page at FARM SHOW →
Best Buy

Ford F-250

Ronald Arp, Hills, Minn. · Vol. 18, No. 3 (1994), p. 15

Ronald Arp, Hills, Minn.: “My 1993 Dixon ZTR 424 mower works great and does a good job. It works fast and is fun to operate. I’ve adapted a lot of attachments to iG bearing lock collars weren’tsettightenough at the factory and belts were poor quality. It wasn’t a dependable machine. “My 1989 Ford F-250 4-WD pickup equipped with a diesel engine has been a nightmare. Almost every part on it, except “Tt's one of the most underated balers on the market. A 10-year-old could operate it.” for the engine, failed before it even had 100,000 miles. I bought it used with no warranty coverage. I'll never buy another used pickup again, partly because I don’t want to go without a factory warranty.”

See this page at FARM SHOW →
Worst Buy

Tom Larson, St

Tom Larson, St. Edward, Neb. · Vol. 18, No. 3 (1994), p. 15

Tom Larson, St. Edward, Neb.: Tom likes his 1992 Zetor 6245 60 hp tractor. “It’s equipped with front wheel assist, cab, and air conditioning and is fuel efficientand relatively problem-free. It’s built heavy and has a much better finish than some other imported tractors in the same class. It’s a good value, too. “My worst buy is a Quadrastat single lever cable control that installed to operate the 2-spool hydraulic valve on my tractor loader. Push-pull cables connect the lever with the valve but I can’t get it to operate smoothly or precisely.”

See this page at FARM SHOW →
Best Buy

Allis-Chalmers 7045 + 2 more

Wendell Suelter, Lincoln, Kan. · Vol. 18, No. 3 (1994), p. 15

Wendell Suelter, Lincoln, Kan.: “My 1979 Allis Chalmers 7045 tractor has performed well above expectations. Excellent lugging ability and handles well. “Lcan’tsay enough good things aboutmy 1991 Dew Eze flatbed. We use it to haul round bales and doa lotof other jobs. It's the most valuable tool on our farm, “My 1991 New Holland 855 round baler is the most underated baler on the market. A 10-year-old child could operate it.” On the minus side, Wendell lists his 1989 Hesston 5585 round baler. “It spent as much time in the shop as it did in the field. The pickup attachment was a disaster, The bearing lock collars weren’tsettightenough at the factory and belts were poor quality. It wasn’t a dependable machine. “My 1989 Ford F-250 4-WD pickup equipped with a diesel engine has been a nightmare. Almost every part on it, except “Tt's one of the most underated balers on the market. A 10-year-old could operate it.” for the engine, failed before it even had 100,000 miles. I bought it used with no warranty coverage. I'll never buy another used pickup again, partly because I don’t want to go without a factory warranty.”

See this page at FARM SHOW →
Best Buy

Gehl 1310 + 1 more

Lorne Orr, Lambeth, Ontario · Vol. 18, No. 3 (1994), p. 15

Lorne Orr, Lambeth, Ontario: “My 1992 Gehl 1310 round baler is my best buy. It’s easy and simple to operate. It’s not a high-tech machine, but it works good and is reasonably priced at about $1,000 less than other balers of its size. “Our Bobcat 731 skid steer loader is a great companion to the baler. We use it for hauling and stacking bales.”

See this page at FARM SHOW →
Best BuyWorst Buy

Ford 8630 + 4 more

Ray Fiedler, St. Joseph, Minn. · Vol. 18, No. 3 (1994), p. 15

Ray Fiedler, St. Joseph, Minn.: Ray's impressed with his 1993 Ford 8630 2-WD tractor. “I really like the powershift transmission, foot throttle, and cab. It has doors on both sides. “My 1992 Case-IH 600 silage blower runs smooth and has a lot of capacity. use it with a 100 plus hp tractor.” On the negative side, Ray lists his Deere 1219 mower conditioner. “I bought it in the fall of 1992 when I traded in an 8-year-old New Holland 489 haybine and used it for the first time in 1993. didn’t like the way itcut - hay plugged up at the sickle guards.”

See this page at FARM SHOW →
Worst Buy

John Deere 265

Billy R. Snider, Dundas, L. · Vol. 18, No. 3 (1994), p. 15

Billy R. Snider, Dundas, IL: “My best buy is a Classic outdoor wood buming furnace (Central Boiler, Inc., Greenbush, Minn.). This efficient unit heats our house and all our hot water. It sits outside sol don’t have to worry about fire or carbon monoxide in the house and it doesn’t take oxygen or humidity outof the house. Ican fill it with wood and then forget about it for two or three days. You can run the shower all day without running out of hot water. “My 1991 Deere 265 riding mower with a46-in. deck is my worst buy. When it was new it was hard to start. The engine would quit at least once or twice every time I mowed the yard. It took the dealer two years to solve that problem. I solved the starting problem myself. It does a good job on level ground but gouges on uneven ground. wish it had foot-operated hydrostatic controls instead of hand-operated controls. Also, I don’t like the hand lift. It has to be all the way up or down before the deck can be locked in place. I think there are better riding mowers on the market for less money.”

See this page at FARM SHOW →
Worst Buy

L

L.A. Childs, Manchester, Iowa · Vol. 18, No. 3 (1994), p. 15

L.A. Childs, Manchester, Iowa: “My Pax hog waterers are advertised as energyfree and guaranteed not to freeze when installed according to the company’s specifications, which we followed. However, even at 20 degrees above zero we had to spend most of the winter carrying hot water to try to thaw them out. I was very disappointed with the company’s response to my problems.”

See this page at FARM SHOW →
Best Buy

Black+Decker 4075 + 1 more

Jeff Collins, Cumberland, Ohio · Vol. 18, No. 3 (1994), p. 15

Jeff Collins, Cumberland, Ohio: “Tlike my Black & Decker 4075 electric angle grinder. I’ve used it for years and worn out dozens of 7- and 9-in, grinding wheels. The only repairs have been to one or two sets of brushes and to the switch. It’s a rugged American-made tool at a good price. “I'm pleased with my Makita 9501 4-in. electric grinder. I’ve only had to replace several sets of brushes, one or two armature bearings, and the power cord.”

See this page at FARM SHOW →
Best Buy

John Deere 4440

Bryan Gibson, Gormley, Ontario · Vol. 18, No. 3 (1994), p. 15

Bryan Gibson, Gormley, Ontario: “It's the best tractor I've ever owned,” says Bryan about his 1980 Deere 4440 tractor. “It has 4,600 hours and has done every job on our farm. It’s gone through two water pumps, two alternators, two sets of batteries, one neutral start switch, and a pair of front tires. Other than that, it's been trouble-free. “My 1990 Yetter 6600 RT coulter cart with cultivator-packer that I use to pull a 3pt. grain drill simply didn’t work. It was shipped withoutsetup instructions and short on parts. Once in the field I knew why only two units had been sold in Ontario up until that time. From front to back it was poorly designed. The hitch wore out after only 300 acres. The packer was so heavy it pushed dirt in frontof it and the tractor couldn't pull it. After two years I gave it to a dealer for a nominal fee. Now he can’t sell it.”

See this page at FARM SHOW →
Best Buy

John Deere 4020 + 2 more

R.D. Fricker, De Valls Bluff, Ark. · Vol. 18, No. 3 (1994), p. 15

R.D. Fricker, De Valls Bluff, Ark.: “My best buy is a Long 1200 3-pt. backhoe that I bought used from a farmer who had used it on his Deere 4020 tractor. The tractor’s -high oil pressure and high volume of oil caused it to leak quite a bit of oil. I had the main valve rebuilt for $50 and replaced some hoses. I bought it to use on my Deere 2355 tractor, but might also use it on my Deere 4620. installed a ‘T’ in the hydraulic line between the pressure control valve on the tractor and the hydraulic cylinder valve and ran a hose from the T to a Prince RD150-16 adjustable 0-16 gpm flow control valve that I bought from Northern Hydraulics (ph 800 533-5545). I had to use the flow control valve because the backhoe uses only uses 8 gpm. The return line goes to a porton the hydraulic oil filter cannister. “Tuse the backhoe to dig ditches, remove stumps, and transplant small trees and bushes. I also use it to repair levees and to ( )\9.~2— #£=£pape cunw.ac Best & W ( drain rice fields.”

See this page at FARM SHOW →
Best Buy

Ram + 1 more

Jay Volk, Arlington, Neb. · Vol. 18, No. 3 (1994), p. 16

Jay Volk, Arlington, Neb.: “T’ve worked this tuck like a tractor but it still rides like acar,” reports Jay, impressed with his 1978 Dodge extended cab 4-WD pickup. “We “I've worked this truck like a tractor but it still rides like a car.” blew out the engine hauling hay so I overhauled it, as well as the transmission and transfer case. I wouldn't trade it for a new one.”

See this page at FARM SHOW →
Best Buy

Ford 1220

Robert B. Sharp, Bashaw, Alberta · Vol. 18, No. 3 (1994), p. 16

Robert B. Sharp, Bashaw, Alberta: “Our 1988 Ford 1220 15 hp diesel garden tractoris our best buy. We use ilto move and operate our 8-in. dia., 50-ft. long grain auger because it’s so casy to maneuver. It has a lot more power than any of the gas tractors we used in the past. The 3-pt. hitch lets us use it on various makes of mowers, rototillers, and blades. “My Skil 2305 rechargeable screwdriver isa best buy, I'm getting so lazy that won't put in a screw or tighten a hose clamp without it. I’ve retired most of my screwdrivers to pry bar heaven.” Robert says his Australian-designed Computorspray is a “worst buy”. “It has some excellent features - ground-driven pump, manual fold booms, and a tank that’s designed for easy clean out. However, it’s poorly made and has broken in places due to design problems. To put it into transport position, I have to crawl underneath it and remove the drive chain. It’s nerve wracking because I never know if it’s going to finish a field before it quits working.”

See this page at FARM SHOW →
Best Buy

John Deere 7200 + 3 more

C. Tim Bishop, Queenstown, Md. · Vol. 18, No. 3 (1994), p. 16

C. Tim Bishop, Queenstown, Md.: “My 1993 GM 2500 2-WD Suburban with a454 cu. in. engine is my best buy. I installed a set of Thorley headers equipped with a Walker Super Turbocharger muffler and a reprogrammed Hypertech computer chip. I got 11 to 12 mpg towing a 24-ft. race car trailer and 15 mpg without the trailer while hauling 7 passengers or 30 bags of seed corn. I'll pass up anything on the road and has the style and comfort of a luxury automobile. It also has great resale value. However, I wish ithad remote electric door locks and heated side mirrors. “My 1993 Deere 7200 6-row, 30-in. vacuum planter is equipped with Yetter residue managers. It's easy to adjust and plants accurately. Last year I had my best ae > orst Buys ious page) stand of no-till corn ever. “My Deere 9500 combine is equipped with Pixall snapping rolls that eliminate the need to chop corn stalks (Pixall Mfg., Clear Lake, Wis. 54005). The rolls have 10 sharpened, chrome-plated knife blades that intermesh to grip corn stalks and weeds, pulling them down through the snapper plates and crimping them for faster decomposition, We use a Deere 750 no-till drill to plant notill soybeans in untouched corn stalks the following year. Both the combine and drill do an excellent job and have good resale value.”

See this page at FARM SHOW →
Best Buy

Craftsman

John Pierskalla, St. Cloud, Minn. · Vol. 18, No. 3 (1994), p. 16

John Pierskalla, St. Cloud, Minn.: “Two years ago I boughta Sears Craftsman circular saw for $75. It’s an expensive piece of junk. I didn’t even get to use it long enough to sharpen the blade before a short developed in the armature. The company wants $59 to repair it. It's more than a year old so it’s no longer covered by warranty.”

See this page at FARM SHOW →
Best Buy

Frank Hunter, Lumby, B

Frank Hunter, Lumby, B.C. · Vol. 18, No. 3 (1994), p. 16

Frank Hunter, Lumby, B.C.: “I bought a 1979 Versatile 155 tractor used three years ago and it’s my best buy. It's a great all-around tractor. I bought it equipped with a log grapple which is worth its weight in gold. I use it to move pallets, round bales, lumber, logs, and machinery.”

See this page at FARM SHOW →
Best Buy

Tim Stanton, Feura Bush, N

Tim Stanton, Feura Bush, N.Y. · Vol. 18, No. 3 (1994), p. 16

Tim Stanton, Feura Bush, N.Y.: “I like my Hesston 12-wheel bi-fold rake. It does a good job and can cover 15 to 20 acres per hour without damaging hay. My only complaintis that it folds manually. Newer models fold hydraulically. “We've had problems with Kory 8-ton wide track running gears mounted on two wagons. The spindles and main rear beams on both wagons bent the first year, and two front spindles broke the second year. We’ ve used six different brands of running gears over the past 10 years with fewer problems than we’ve had with these in just two years.”

See this page at FARM SHOW →
Best Buy

Chevrolet S-10

Earl Zeltwangen, Wyatt, Ind. · Vol. 18, No. 3 (1994), p. 16

Earl Zeltwangen, Wyatt, Ind.: Earl nominates his new Chevrolet S-10 4-WD extended cab pickup as “best buy”. “It runs smooth, is easy on fuel, and the 4-WD works good. I really like it. “We extended our shop with a 50-fl. Butler all-steel building and like ita lot, It’s completely insulated. We also installed a Shenandoah waste oil burning heater that works good. I’m a dealer for it.”

See this page at FARM SHOW →
Best Buy

John Deere 7600

Francis Burch, Lester Prairie, Minn. · Vol. 18, No. 3 (1994), p. 16

Francis Burch, Lester Prairie, Minn.: He's happy with his 1993 Deere 7600 dicsel tractor. “I like the roomy cab. Ithas a lot of window area which provides great visibility. The 3-pt. is easy to use, and the tractor is easy to service and refuel. was unhappy with how the transmission shifted al first, but an update kit greatly improved i”

See this page at FARM SHOW →
Best Buy

Case + 2 more

Richard Arsnman, Payson, HL · Vol. 18, No. 3 (1994), p. 16

Richard Arsnman, Payson, HL: “I'm well-satisfied with my 1992 Case-IH 7120 tractor equipped with front wheel assist. It has a lot of power and traction, a quict cab, convenient controls, and an 18-speed powershift transmission that makes ita pleasure to operate. “T like my 1991 Deere 9500 combine with rear wheel assist. It walks right through soft fields where others would bog down and has the power and capacity to handle high yielding crops fast and efficiently. It can be adjusted to save more grain than any other combine I’ve ever used.”

See this page at FARM SHOW →
Best Buy

George T

George T. Wilson, Brusett, Mont. · Vol. 18, No. 3 (1994), p. 16

George T. Wilson, Brusett, Mont.: “My 1989 Versatile 276 Bi-Directional tractor is a best buy. The hydrostatic 4-WD has superb traction and it’s articulated so I can get into tight places. The loader is the best I’ve ever used. The engine starts well in winter.”

See this page at FARM SHOW →
Best Buy

New Holland L-35

Luke Verbyla, Benton, Penn. · Vol. 18, No. 3 (1994), p. 16

Luke Verbyla, Benton, Penn.: Luke's pleased with his Rock-O-Matic 57 rock picker, which he bought used. “It’s a tough machine - no problems in five years. It cost less than a hernia operation and is always ready to work. My brother's also pleased with his Rock-O-Matic. “We've had trouble with our 1991 New Holland 553 skid steer loader. The cab is so small it must have been made for a midget, and the muffler broke with only 90 hours on the machine. Hydraulic oil started leaking at 400 hours. It has poor traction when it’s notonconcrete. I had owned a New Holland L-35 model which liked much better.”

See this page at FARM SHOW →
Best Buy

John Deere F-510 + 1 more

Jerry Kroll, Montague, Mich. · Vol. 18, No. 3 (1994), p. 16

Jerry Kroll, Montague, Mich.: “My “The cab is so small it must have been made for a midget.” 1992 Deere F-510 front-mount mower is a pleasure to operate, has plenty of power, and is maneuverable, It does a perfect job mowing. All components are easy to reach and service. No problems at all. “My 1992 Automatic ATF-600 roller mill works fastand does a nice job. Last fall I used it to crack shelled corn which I then discharged into a silo blower. I was able to keep up with our Massey-Ferguson 550 combine which is also a best buy.”

See this page at FARM SHOW →
Best BuyWorst Buy

Bobcat 743 + 1 more

Tom Dent, Oak Grove, Mo. · Vol. 18, No. 3 (1994), p. 16

Tom Dent, Oak Grove, Mo.: “I like my Clark-Melroe Bobcat 743 and 440B skidsteer loaders. They’re tougher than a box of rocks and can do more work than a herd of horses.” On the “worst buy” side, Tom lists his Milwaukee 1/2 hp hammer drill. “Whenever I get ithung up it almost always strips the gears. Repairs are expensive.”

See this page at FARM SHOW →
Best Buy

Ram + 1 more

Cliff Wetzel, Ithaca, Mich. · Vol. 18, No. 3 (1994), p. 16

Cliff Wetzel, Ithaca, Mich.: Cliff's had trouble with his 1989 Dodge Ram 4-WD diesel pickup. “I drove less than 150 miles before the fan belt failed because the air conditioner had been improperly installed. A few thousand miles later the air conditioner wiring caughton fire. Apparently, the wiring was installed on the wrong side of the steering column and pulled tight against the clutch rod which wore through the insulation, There was no warranty on electrical components, The repair bill was more than $500. “Next, I was driving on the highway when I detected an odd noise and looked out my mirror to sce that the rear wheel and axle had slipped beyond the wheel fender. That cost me another $300 for towing, parts, and labor. I've also had trouble with the fuel tank whenitgets down toabout 1/3 full. The truck nearly stalled on a long uphill grade and I had to bleed the fuel line. The tank is flat, over 5 ft. long and the fuel line is 2 in. above the bottom of the tank at the center. When going uphill, fuel flows to the back of the tank, “Icalled the company and spoke with the truck manager. He told me that I was the only person to ever complain about this problem, If I was the only person to ever complain, then why was the shape of the tank changed on the 1990 model to solve the very problem I complained about? “The next problem occurred when I was 150 miles from home - the transmission gave out.1 hauled the uuck back home, removed the transmission, and took it to a repair shop. When I returned home, received a call from the shop owner who told me that Dodge didn't sell any ansmission parts for its 1988 or 1989 model pickups. The dealer called Detroit and got the same answer. We were told, however, that we could buy a new transmission for $2,800. We only needed asmall part, butwecouldn’t getit. When I bought the pickup, neither the dealer nor the company told me that I wouldn’t be able to buy a part for the transmission if I should ever need it. “T received a followup call later from the company saying that Dodge had started selling transmission parts for 1988-89 trucks. But the fact remains that this has been one expensive lemon of a truck. Except for the Cummins engine, it has not performed well atall.”

See this page at FARM SHOW →
Worst Buy

Walter Fifelski, Wayland, Mich

Walter Fifelski, Wayland, Mich. · Vol. 18, No. 3 (1994), p. 16

Walter Fifelski, Wayland, Mich.: “My worst buy is a 1993 M.T.D., riding mower with an 18 hp Briggs & Stratton gas engine. L used it for only about 20 hours last year. When I started it this spring the engine had a terrible knock. I thought the problem was a bad bearing so I took it to an authorized service center. They told me the problem was due to carbon buildup on the piston and head and that if the carbon wasn'tremoved, considerable damage would occur. Scraping the carbon off cost me $150. 1 was told by the service center that neither M.T.D. nor Briggs & Stratton would pay for the repair. They said the problem is that heads on late model Briggs& Stratton engines have such close tolerance thateven the smallestamount of carbon will cause the piston to ‘hammer’, I’ve owned almost every kind of gas engine ever made and this is the first time I've ever heard of this problem.”

See this page at FARM SHOW →