Real farmers rate what they bought, from FARM SHOW MagazineSubscribe  ·  Free issue  ·  Send us your Best or Worst Buy
Subscribe to FARM SHOW
Home › Issues › Vol. 25, No. 2 (2001)

Best & Worst Buys: FARM SHOW Vol. 25, No. 2 (2001)

63 reports from pages 14–17 · 60 Best Buys15 Worst Buys · See everything in this issue at FARM SHOW →

Worst Buy

Belarus 825 tractor

Stuart Klingel, Nazareth, Pa. · Vol. 25, No. 2 (2001), p. 14

“My worst buy of all time is my 1993 Belarus 825 tractor. It has had a lot of problems including hydraulic failure (twice), malfunctioning brakes, wiring problems, and an fuel injectionr pump that had to be replaced. All of these problems happened within the first 60 hours of use. The company took the tractor back and gave us another new one but unfortunately we had the same problems with that one, too. Also, the new model started to blow oil out the exhaust.

“We used the tractor only for light duty work. One day my dad was using the tractor to pull two empty wagons when the thumb screw holding the telescoping steering wheel worked itself loose. The steering column came apart and my dad lost steering control. The tractor veered off the road and hit a tree, which caused a lot of damage to the tractor and injured dad. The tractor was taken back to the dealer. They fixed the damage to the outside and put the steering column back together, but they couldn’t guarantee us that it would stay together. They said the oil blow-by had been fixed and that the problem was ‘just a loose bolt’. However, while the tractor was still at the dealer we noticed fresh oil running down the exhaust stack.

“They said they would fix the engine problems but they didn’t and we’ve been in litigation since 1995. The company finally made a financial compensation offer in December of 1999, but we turned it down because it was less than what we paid for the tractor. Then in March of 2000 we found out that Belarus is in bankruptcy. But they have a parent company so our lawyer is pressing on. Our tractor has been at the dealer’s since January of 1995 even though we paid for it in full. I’d like to hear from anyone who has had similar problems.”

Best BuyWorst Buy

Bobcat 753 skid steer loader + 2 more

Tom Rice, Galesburg, Mich. · Vol. 25, No. 2 (2001), p. 14

“My 1999 Bobcat 753 skid steer loader is my best buy. It’s easy to use and has great balance and power. This is the sixth Bobcat we’ve owned over the past 30 years or so.”

On the negative side, he lists his Manco 4-wheel go-cart type ATV equipped with a Tecumseh 4 hp engine. It was made by Manco Products, Ft. Wayne, Ind. “The engine leaked oil from the start. The dealer said they all leak oil and not to worry about it. The engine finally blew the crankshaft when it was only two months old. No one would honor the warranty. They just passed the buck. I faxed the company but got no response. I’ll never buy any of their products again or recommend them to others. “

Best Buy

Brian Skipper 4371 + 1 more

James Allen, Clare, Iowa · Vol. 25, No. 2 (2001), p. 14

An add-on chopper kit for his Case-IH Axial Flow combine, which was featured in FARM SHOW, rates as his “best buy”. The kit is made by Brian Skipper, 4371 Gleeson Line, Rt. 1, Tilbury, Ontario, Canada N0P 2L0 (ph toll free: 877 754-7737). “I paid less than $100 for it and have used it for five years. It consists of a chopper bar that’s fitted with sickle sections that replace the original short, U-shaped cutter blades. They wear well and stay sharp longer. The real difference shows when cutting green stem soybeans. We installed kits in our Case-IH 915 and 2388 combines. It makes the factory chopper work like a real chopper. It’s possible to get 2,500 to 3,000 acres from one of these kits. “

“Our 1993 DMI 730 Ecolo Tiger disc ripper still looks as good as new and is a best buy. We use our 20-ton, 400 hp Steiger tractor to pull it. We’ve never used a welder on it because nothing on it ever broke. It’s a good tillage tool that’s built to work in any condition.”

Best BuyWorst Buy

Harbor Freight Co + 1 more

Jon C. Thompson, Kalamazoo, Mich. · Vol. 25, No. 2 (2001), p. 14

“We’ve purchased items from Harbor Freight Co. in California for the past 15 or 20 years. It’s true that some of their products are rough, but you can’t beat their low prices. Any complaints we’ve had have been handled quickly and fairly.

“We purchased a Black & Decker table saw and it ran through a “special” belt after we had used it only twice. When a new “special belt” was installed, the motor quit after about six more uses. Black & Decker used to have quality tools, but regretfully that no longer appears to be true.”

Best Buy

Gilcrest HTD rotary mower + 1 more

Richard Jaescke, Northampton, Ma. · Vol. 25, No. 2 (2001), p. 14

“My 1999 Gilcrest HTD rotary mower is my best buy. It’s a rear-mounted, heavy duty model equipped with rubber tire drive. It holds up to our rugged New England fields. There were some problems with the tail wheel assembly but they’ve been solved on new models. I like the rubber tire drive system because it protects the tractor’s driveline.

“My 1998 Twose 520 hydraulic boom mower is also well built. I do guard rail mowing for local towns so the machine I use has to be reliable. This one is made in England. A lot of thought went into the design, such as the routing of the hoses. The rotor is belt-driven so as to protect it from shock, etc. I’d recommend this machine to anyone.”

Best Buy

Ram 2500 heavy duty pickup

W.S. Hunter, Dilley, Texas · Vol. 25, No. 2 (2001), p. 15

“We’re happy with our 2000 Dodge 2500 heavy duty pickup equipped with a quad cab and a 24-valve Cummins turbocharged diesel engine. We have more than 22,000 miles on it. It averages about 19 mpg. On a 2,000-mile trip last year it got 24 mpg at an average speed of about 65 mph. It rides a little rough but has a lot of pulling power. The 4-speed automatic transmission requires very little down-shifting even when towing a 24-ft. fifth wheel trailer.”

Best Buy

Kubota tractor

Tom O’ Brian, Dimmitt, Texas · Vol. 25, No. 2 (2001), p. 15

“I’m happy with it. No problems at all,” says Tom about his 1993 Kubota tractor which he bought used. “My only expense was for a new battery. It easily handles our Bush Hog 6-ft. shredder, which is also a best buy.”

Best Buy

Lincoln electric

Dennis Robertson, Eagle, Neb. · Vol. 25, No. 2 (2001), p. 15

“My Lincoln electric Weld Pak 100 welder runs on 115-volts so I can take it anywhere and plug it in. I’ve used it to weld up to 1/4-in. thick steel with no problems. All welds are still holding.”

Best BuyWorst Buy

Husqvarna chain saws + 1 more

Edwin Mitchell, Brantley, Alabama · Vol. 25, No. 2 (2001), p. 15

“Over the years I’ve owned three Husqvarna chain saws and one Husqvarna weed eater. They all start easy and have had few problems.

“My 1995 Ford 6640 tractor is my worst buy. The problem is that it uses a lot of oil. The dealer did a ring job on the engine but that didn’t help at all. Then he installed a new engine, but unfortunately it used as much oil as the old one. If we worked the engine hard it would use about a quart of oil every day. A local mechanic told me to use Shell Rotella oil in the engine. I did, and after three oil changes it doesn’t use oil any more.”

Best Buy

Sears Craftsman lawn tractor/mower equipped

Richard C. Bowman, Chambersburg, Pa. · Vol. 25, No. 2 (2001), p. 15

“My Sears Craftsman lawn tractor/mower equipped with a Briggs & Stratton 18 hp twin-cylinder engine and 46-in. deck is my best buy. The engine has a lot of power and runs smooth. I weigh 270 lbs. yet I can mow 45 degree slopes with ease (I go up and down the slope, not crosswise). It’s very easy on fuel,too. After 10 years of use all I had to replace was one belt on the mower. The only thing I don’t like is that there are no grease zerks on the steering parts (tie rods, drag links, etc.). I paid a welder $2.00 to fix one of the ball joints instead of spending $800 for new Sears parts.”

Best Buy

Case-IH 7140 tractor + 1 more

David J. Fangman, Elma, Iowa · Vol. 25, No. 2 (2001), p. 15

“My1989 Case-IH 7140 tractor is my best buy. It has more than 5,000 hours on it. It runs well, has a lot of power, and rides nice. It had a few oil leaks which we had to fix, but no major problems.

“My PFM rock picker is a best buy. The hydraulic swing on the tongue makes it convenient to pick up several rocks without having to back up and move over or circle around.”

Best Buy

Kubota B2150 4-WD tractor equipped

Byron Tims, McDavid, Fla. · Vol. 25, No. 2 (2001), p. 15

Byron’s impressed with his Kubota B2150 4-WD tractor equipped with a 24 hp engine and a 60-in. belly mower. “I use it to cut about 2 1/2 acres of grass and to pick up loads of leaves. I also use it with a trailer in my garden to haul loads of heavy, green wood from the woods. The starter and alternator needed repairs and a seal on the mower had to be replaced. Otherwise, it has required only routine maintance. I’ve got about 800 hours on it. One negative is that the belly mower sometimes drags going over high places such as terraces or ditches.”

Best Buy

John Deere 345 lawn

Earl H. Mitchell, Bellevue, Ohio · Vol. 25, No. 2 (2001), p. 15

Earl’s happy with his 1998 Deere 345 lawn and garden tractor equipped with a 48-in. mower and 42-in. snowblower. “It replaced my 1977 Deere 212, which was an excellent tractor. In fact, at trade-in time, the 212 was still using its original spark plug. But the 345 is a much superior tractor because it has power steering, hydraulic lift, an automatic transmission, and a tighter turning radius. It handles the snowblower particularly well and is a real pleasure to operate.”

Best Buy

Stan MacDonald

Paul Shuster, St. Johnsville, N.Y. · Vol. 25, No. 2 (2001), p. 15

“I’m well satisfied with the drill bit sharpener I purchased from Stan MacDonald (402 Rosedale ave., Foxboro, Ontario, Canada K0K 2B0). I bought it after reading about it in FARM SHOW. It’s simple to operate and does an excellent job of sharpening compared to other brands. The sharpening process doesn’t take much time and when I’m done the bits are like new.”

Worst Buy

John Deere 348 baler

Brian Folmer, Pen Argyl, Pa. · Vol. 25, No. 2 (2001), p. 15

Brian’s had bad luck with his 1998 Deere 348 baler. “We bought it to replace our Deere 347 baler which had some years on it. We thought the new baler would decrease our downtime, but we were wrong. The first problem was that the company was five months late in delivering the baler. The knotter mechanism didn’t work right and the baler jumped up and down from the start. The front hitch bolt broke after only one year of use, and the bearings came loose on one of the wheels. The filtering screen wasn’t screwed into place in the bale kicker’s oil reserve. The piston for the kicker was destroyed when a fitting broke and went into the piston. The dealer wasn’t very prompt in fixing any of these problems.”

Best Buy

Brandt 860 dia long

Roy Crane, Martinsville, Ill. · Vol. 25, No. 2 (2001), p. 15

Roy’s the satisfied owner of used a Brandt 860 8-in. dia., 60-ft. long auger equipped with a swingaway hopper which he bought used three years ago. “I was unfamiliar with this brand of auger and was apprehensive about buying this one when I ran across it at a local implement dealer. It was priced at a reasonable $650 so I took it home and put it to work. It’s equipped with a pto main drive and hydraulic drive hopper and raises and lowers hydraulically. It has performed well after a lot of hard use. I’m well pleased with it.”

Best BuyWorst Buy

New Holland 688 round baler + 1 more

Dean McDaniel, Beaver, Okla. · Vol. 25, No. 2 (2001), p. 15

“My New Holland 688 round baler does a great job of starting bales and makes them nice and tight. It also does a good job ejecting bales.

“My Vermeer 605J round baler is my worst buy. I bought it to put net wrap on my bales but found that it did a poor job. I could put one good wrap on, but then the next bale would have too much wrap on one side and not enough on the other. I finally traded it in for a New Holland.”

Best Buy

Ram 3/4-ton pickup equipped + 1 more

Victor Cripps, Gladwin, Mich. · Vol. 25, No. 2 (2001), p. 15

“My best buy is my 1995 Dodge 3/4-ton pickup equipped with a 318 cu. in. engine. It has more than 200,000 miles on it but is still going strong.

“I still use my International Farmall M tractor equipped with a narrow front end. I also like my Farmall 450 equipped with a wide front end. It does an outstanding job for its size. It starts right up even when the temperature is way below zero.”

Best Buy

Enertia house

Michael Sykes, Wake Forest, N.C. · Vol. 25, No. 2 (2001), p. 15

“We built our house in 1986 and for 15 years have paid nothing for heating or air conditioning. This savings has already paid for the house. During hurricanes Fran and Floyd we had electricity - thanks to the solar panels - when no one else did for 14 days. We can now sell our extra electricity back to the co-op for cash,” says Michael, who built the Enertia house which was featured in FARM SHOW’s Vol. 12, No. 4 (Enertia Building Systems, 13312 Garffe Sherron Road, Wake Forest, N.C. 27587 ph 919 556-0177; Website: www.enertia.com). “It’s a no-furnace house built with salt-injected wood that requires little or no energy to heat or cool. The house has insulation only in the roof. Its interior and exterior walls are made of wood that has been pressure-treated and injected with salt to enable it to absorb and store heat or cold. The dense, treated lumber slowly releases stored energy into the home over an extended period of time, thus reducing energy demands. The key feature of the new-style house is the “envelope” construction of the north and south walls which are double-layered with an air space between. Heated air flows freely in a circular motion through the walls, ceiling and basement, radiating into the house through interior walls.

“I now build these houses and can’t get them up fast enough.”

Best Buy

New Idea 5200 disc mower conditioner + 1 more

James L. Evans, Hammond, N.Y. · Vol. 25, No. 2 (2001), p. 15

“My 2000 New Idea 5200 9-ft. 3-in. disc mower conditioner is my best buy. It’ll mow through any kind of grass whether it’s wet or dry, and at a fast speed - maybe faster than I should be driving the tractor. All I have to do is hook up, grease it, and go.”

“My 1999 Hesston 9-ft. 3-in. windrower is my worst buy. Every time I use it I seemed to have down time. The main problem is that the mower sections keep breaking and they’re hard to change even though they are the bolt-on type. I adjusted everything as recommended in the owner’s manual.”

Best Buy

Ram 2500 SLT pickup equipped + 1 more

David M. Welling, Ridgeway, Ohio · Vol. 25, No. 2 (2001), p. 15

“My 2001 Dodge 2500 SLT pickup equipped with a 24-valve Cummins air-cooled diesel engine and 4-speed automatic transmission is my best buy. It has a lock-up torque converter and a 3:55 rear end gear ratio. The only problem was that it took a long time to get it. I ordered it in February 2000 but didn’t receive it until four months later. However, it was worth the wait. I really like the black-over-gray finish. I also like the vehicle’s power and torque. With all that torque and the anti-spin rear axle, I have to be careful or I’ll end up going sideways.

“Regarding Harbor Freight tools, you really have to watch what you buy. Some of the products are misleading as far as their claims of being made in the U.S.A. For example, I ordered a Hanson drill bit set. The index box was made in the U.S., but the drill bits were made in China and were of poor quality.

“I’ve owned Snap-On tools for more than 22 years and have never been disappointed with them. I’ve traded and upgraded toolboxes and tools over the years, both hand-operated and power models, and their trade-in value is great. I’ve used a 1/2-in. air impact tool for 20 years and it has never been rebuilt. I traded it for a new 2000 model and the dealer gave me $75 for it. Snap-On tools cost a little more, but in the end you don’t have a piece of junk when it comes time to trade or upgrade.”

Best Buy

International Harvester CX 80 front wheel assist + 1 more

J.M. Leininger, Jr., Loudonville, Ohio · Vol. 25, No. 2 (2001), p. 15

“My International CX 80 front wheel assist tractor is easy to handle and starts good in cold weather.

“My 1991 Honda Four-Trax 300 ATV is a best buy. I bought it used when it was one year old. All I have to do is change the oil and put gas in the tank - and not very often. I use it every day during the pasturing season to build fence, get the cows, go after parts, or drive to another piece of equipment. I mounted a towbar on front so I can pull it behind my pickup or tractor. It’s well built. I’d definitely buy another one.”

Best Buy

Kioti 4-WD tractor equipped

Norman Talbot, Rochester, N.H. · Vol. 25, No. 2 (2001), p. 15

“I’m well pleased with my 1997 Kioti 4-WD tractor equipped with a 30 hp engine and power steering (O’ Bryan Implement Sales, 5th St. and Crabtree Ave., Owensboro, Ky. 42301 ph 800 427-3299 or 270 684-1741 or 1749). I don’t know why these tractors aren’t more popular.”

Best Buy

Honda 450S ATV

Glen Schnegg, Powhatan Point, Ohio · Vol. 25, No. 2 (2001), p. 16

“It’s one of the best purchases I’ve ever made,” says Glen, happy with his 2000 Honda 450S ATV. “It takes most of the work out of routine farm chores and even makes me look forward to doing them. No problems so far. I’ve even used it to pull 24-in. dia., 7-ft. logs.”

Best Buy

Case-IH 7130 Magnum

Brian I. Lesiuk, Gilbert Plains, Manitoba · Vol. 25, No. 2 (2001), p. 16

“My 1993 Case-IH 7130 Magnum is a great tractor. It has a lot of power and a great all-around view from the seat. It’s also fuel efficient - I can work more than 220 acres on a tank of fuel while pulling a 32-ft. air seeder equipped with a 155-bu. seed tank and going 5 1/2 mph. It has been in the shop only once for a factory recall on the pto.”

Best BuyWorst Buy

Deutz 7206 + 3 more

Gene D. Zimmerman, Fox Lake, Wis. · Vol. 25, No. 2 (2001), p. 16

“My Deutz 7206 and 7085 tractors are dependable and easy to operate. They’re also super fuel efficient.

“My Krone 125 round baler is easy to use and makes great bales. It can bale just about anything including wheat straw, bean straw, and corn stalks without missing a beat.

“My Deere F525 front-mount lawn mower is a big disappointment. It looks like a Deere but runs like a John. It was worn out after only one year, even though we use it on less than a half acre of grass. It was difficult and expensive to fix. Three different dealers tried to fix it without success. We finally traded it in.

“My FarmWork computer software was a nightmare to install and technical support from the company was poor. It was a real disappointment.”

Best BuyWorst Buy

John Deere 4240 tractor + 3 more

Allen Derrer, Lanark, Ill. · Vol. 25, No. 2 (2001), p. 16

“I bought my 1978 Deere 4240 tractor used when it was seven years old and it’s my best buy. It has more than 9,200 hours on it . The only major repairs have been to the crank bearings and ring pump. This tractor seems to have more power now than when it was new.

“My 1978 Ford F-250 4-WD pickup equipped with a 351 cu. in. engine is a best buy. I bought it used when it was two years old. It has more than 210,000 hard miles on it and the engine has never been overhauled.

“I bought my 1990 Ford F-150 4-WD pickup used when it was six years old and it’s my worst buy. The pickup’s 302 cu. in. engine is underpowered, even though it has electronic fuel injection and this a lighter truck. It used more fuel and had more problems than my 1978 Ford F-250. I finally replaced it with a 1994 Chevrolet equipped with a 350 cu. in. engine. This model has much better performance and economy.”

Best Buy

Woods 5200 zero turn lawn

Miles Filer, Vandalia, Ill. · Vol. 25, No. 2 (2001), p. 16

“My 1994 Woods 5200 zero turn lawn mower equipped with a 20 hp Kohler engine is my best buy. I bought it used two years ago when I traded in a 10-year-old Woods mower that had only 250 hours on it. The front-mount zero turn feature on this model is much more maneuverable than on other zero turn models.”

Best Buy

U.S. Steel siding + 2 more

Lloyd Conrad, Greenfield, Wis. · Vol. 25, No. 2 (2001), p. 16

“We had U.S. Steel siding and insulation installed in 1982 over our home, which had clapboard siding. During the summer of 1998 the steel siding began to flake and chip in certain areas, which seemed to indicate an area of one bundle or square. We were told to contact a company called Alside as they had taken over the company that manufactured the steel siding. We inquired of this company as to what we should do to try and keep the problem from spreading. A number of form letters went back and forth to this company as to cost, date of installation, position of the home as to facing north, south, east or west. We also sent them 10 photos taken from all angles of the structure.

“The original contractor was no longer in business. Our inquiry evidently never got past the office help. We weren’t trying to get them to replace the siding, but wanted information on what we could do to correct the problem. All they did was express their regrets.

“We purchased a Snapper 30-in. riding mower in 1967 to mow our 3-acre orchard. We were limited in height and width dimensions so we had to settle for the 30-in. mowing width. Over the years we’ve installed three engines, but the mower is still going strong. We prefer to operate this old mower over a newly purchased one because it lets us go from forward to reverse with no problems.

“Once we got all the bugs out of our 1987 Chevrolet 1500 pickup it turned out to be a strong, dependable vehicle. The problem was a missing lock washer on the part that connects the steering rod to the gear that turns the steering arm. It was one of the models that GM tried to build without putting any grease fittings on the suspension ball joints.”

Best Buy

Gleaner R5 combine equipped + 1 more

Don Siefert, Bennet, Neb. · Vol. 25, No. 2 (2001), p. 16

Don’s impressed with his 1998 Gleaner R5 combine equipped with a liquid-cooled engine. “It has excellent capacity for a mid-sized combine and does a good job threshing and separating corn, beans, and grain sorghum. The only problem we had was when a pin fell out of a connecting link in the clean grain elevator chain. The engine has a lot of power and runs cool.

“We use a Crary air reel on the combine when harvesting soybeans and it works great. It blows air onto the sickle bar and sends shattered beans into the machine, keeping any short beans from bunching up over the sicklebar. As a result, the crop feeds in evenly.”

Best Buy

Allis-Chalmers WD-45 tractor

Harley Green, Ulen, Minn. · Vol. 25, No. 2 (2001), p. 16

Harley says his best buy of all time is his 1956 Allis-Chalmers WD-45 tractor which he bought used 15 years ago. “I think it has more than 15,000 hours on it. It never fails to start and hasn’t required any repairs. It’s made simple and is easy to maintain. I use mounted implements with it including a sickle mower, loader, rear blade, cultivator, side delivery rake, plow, etc.”

Best Buy

Ram 1500 4-WD quad

Paul J. Bennett, Sr., Toddville, Iowa · Vol. 25, No. 2 (2001), p. 16

Paul’s the owner of a 2001 Dodge Ram 1500 4-WD Quad Cab pickup. “I ordered a 2000 model but they sent me a 2001 model. I ordered it December 3, 1999 and received it January 21, 2000. I didn’t know pickup manufacturers introduced new models a year ahead of time. I’ve driven it a little more than 12,000 miles and I like it a lot. The Quad Cab leather seats and 4-WD are nice. No problems.”

Best Buy

S.I. Distributing, Inc

Mahlon Nepp, Lake Wilson, Minn. · Vol. 25, No. 2 (2001), p. 16

Mahlon likes the long-lasting sickle sections he purchased from S.I. Distributing, Inc., (03221 Barber-Werner Road, St. Marys, Ohio 45885). The sections are hardened all the way through, not just on the surface. “We’ve totally replaced the sections on our self-propelled swather (four years ago), 8-ft. bean head (three years ago), and 7-ft. International mower (two years ago). They cut well and are built tough. So far we’ve had to replace only one guard and two sections. They cost more than conventional sickles but the extra cost is well worth it.”

Best Buy

Besler Stalker stalk cutter

Leon C. Regier, Grant, Neb. · Vol. 25, No. 2 (2001), p. 16

Leon nominates his 2000 Besler Stalker stalk cutter as his “best buy”. “The machine quickly prepares ridges for planting by cutting the root crowns at ground level for easy, smooth planting on the ridge. I can often use it at 8 mph. On any 70 degree day I can do 130 acres in an afternoon before the rush of planting, and it still uses very little fuel.”

Best BuyWorst Buy

GM Brigadier tandem diesel truck + 1 more

Ed Staudt, Vibank, Sask. · Vol. 25, No. 2 (2001), p. 16

“One of our best buys was a used 1979 GM Brigadier tandem diesel truck equipped with an automatic transmission and 20-ft. grain box. It’s easy to operate - anyone can drive it.

“Our worst buy was a Flexi-Coil 820 cultivator. We bought the cultivator new along with a new Flexi-Coil 1720 air tank in the fall of 1994 for use in seeding the following year. We traded in an Eclipse 700 cultivator equipped with a 1110 air tank.

“When we started seeding peas with the unit, we found right away that the machine wasn’t planting at a uniform depth. Seed depth ranged from 0 to 5 in. all across the machine. We stopped seeding and contacted our dealer, who in turn contacted the company. After numerous attempts over a 4-year period by the combined forces of the specialists of both New Holland and Flexi-Coil, the machine was finally made to seed fairly level. However, due to the uneven seeding depth of the machine, we suffered a tremendous crop loss and consequently a large financial loss as well, on 200 plus seeded acreage.

“Rather than taking responsibility for the loss we suffered, the company chooses to attack my farming practices and my own lack of ability to level the machine, even though the specialists of both the dealer and manufacturer were unable to do so. The company also stated that if the machine wasn’t satisfactory I should have bought a replacement machine.

“We feel it’s the responsibility of the dealer and manufacturer to be sure that the machines they sell do the job that it was meant to do, and that the responsibility of making the initial settings should be done by the dealer and manufacturer experts. We also feel that it’s very unfair to expect us to do things that the specialized factory and dealer personnel can’t do. I’d like to hear from anyone with a similar experience or any comments regarding our situation.”

Best BuyWorst Buy

Massey Ferguson 362 tractor + 1 more

James Thomas, Laceys Spring, Ala-bama · Vol. 25, No. 2 (2001), p. 16

“My Massey Ferguson 362 tractor and front-end loader is my best buy. It’s versatile and comfortable to use. No problems after 500 hours of use. It does a lot of work without using a lot of fuel.

“My Long 2610 tractor is my worst buy. The first month the alternator and voltage regulator had to be replaced. Then four months later a noise developed in the rear end. When I drained the gearcase to look for metal particulates, the pin that retrains the spider gear assembly fell out. It was in the shop for 30 more days. The dealer wanted to charge for warranted repairs since I had not purchased the tractor from him.”

Best Buy

Chevrolet 2500 4-WD model equipped + 1 more

Marlin Wahrman, Atwood, Kansas · Vol. 25, No. 2 (2001), p. 16

“It’s the best pickup I’ve ever owned,” says Marlin about his 1992 Chevrolet 2500 4-WD model equipped with a 6.5-liter diesel engine. “I’ve put more than 200,000 miles on it and all I’ve done was to change the oil and put on new tires.

“My 1981 Chevrolet 2-WD pickup is a best buy. It has about 250,000 miles on it and is still going strong.”

Best BuyWorst Buy

Astro Seal + 2 more

Don Lasee, Krakow, Wis. · Vol. 25, No. 2 (2001), p. 17

“A product called Astro Seal is my best buy. I used it to seal a weeping pto gasket on my semi tractor without having to do any draining or disassembly work. It seals through water or oil and doesn’t harden or crack. It works in temperatures ranging from 50 degrees below zero to 220 above. It’ll seal lead, asphalt, glass, wood, sheet metal, concrete, and all solid surfaces. Whatever you seal is paintable immediately. I liked it so much that I became a dealer.

“My Snap-On hand tools are my worst buy. I’v found Snap-On dealers to be extremely arrogant and they refuse to warrant their tools. Also, their polished wrenches may look impressive but they’re difficult to hang onto when you have oily hands. The company’s screwdrivers twist and their cotter pin puller bends. I’d rather have Sears Craftsman hand tools any day.”

Best Buy

Toyota pickup equipped

Michael Mulhern, Cornell, Wis. · Vol. 25, No. 2 (2001), p. 17

A 1988 Toyota pickup equipped with a V-6 engine rates as Michael’s “best buy”. “It has more than 337,000 miles on it and the only repair I had to make was to put in a new clutch at about 250,000 miles. I change the oil about every 10,000 miles. I use this pickup to haul grain wagons and anhydrous wagons, as well as to travel and hunt all over the West. I’ve made many river crossings with it and can hardly resist driving through an inviting piece of mud.”

Best Buy

ATX Building Systems

Ed Jenson, Wellsville, Utah · Vol. 25, No. 2 (2001), p. 17

“I like the 40 by 60-ft. hay barn that was put up for us by ATX Building Systems. It’s the third steel building I’ve built and/or constructed. This one was purchased direct from the company with no middlemen, which saved thousands of dollars. The building was well engineered and required drilling only four holes. It’s built with quality and was easy to erect.”

Best Buy

Allis-Chalmers man

Charles Conner, Jr., Broken Arrow, Okla. · Vol. 25, No. 2 (2001), p. 17

“It’s not the color that counts, it’s what’s under it that counts,” says Charles, who nevertheless says he’s an Allis Chalmers man. He’s especially happy with his 1939 Allis WC tractor equipped with a 14 hp engine. “It had a list price of $960. We’ve used it for all of its 61 years and it still works good. We also own an Allis Chalmers WD, WD 45, 160, 170, and 200. I’m 80 years old. My son and I use these tractors to bale 1,300 bales every year from spring until fall. We don’t ever change implements, we just change tractors with hardly any down time. I’m sold on Allis-Chalmers.”

Best BuyWorst Buy

John Deere 3970 forage harvester + 1 more

John H. Kocher, Pennsylvania Furnace, Pa. · Vol. 25, No. 2 (2001), p. 17

John’s happy with his 1999 Deere 3970 forage harvester. “It seems to take less horsepower, is easier to sharpen the knives, and hasn’t required a lot of maintenance. It’s equipped with a two-speed blower that takes less power in corn silage.

“My worst buy is my Case-IH MX 200 tractor. It has many features on it that don’t work well. For example, the pto wouldn’t start easy which caused bolts to shear. The steel pipe under the cab vibrated and broke off. It should’ve been made from rubber. Both hydraulic cylinders on the 3-pt. hitch leaked. The company should’ve field tested this tractor more extensively before putting it on the market.”

Best Buy

Magnatrac 5000 compact crawler tractor

Robert F. McGinnis, Poughkeepsie, N.Y. · Vol. 25, No. 2 (2001), p. 17

“My best buy is my Magnatrac 5000 compact crawler tractor powered by a 25 hp Kohler ‘V’ twin-cylinder engine. The engine has a computer ignition system, an independent oil cooling and filtering system, and nickel-silicon plated cylinder bores. It meets all current anti-pollution standards. The tractor has heavy-duty hydraulic drive systems to handle the extra power from the engine. The hydraulic system has its own replaceable filter and its own cooling radiator, along with a 15-gal. hydraulic oil tank. The transmission also has an overdrive so I can increase ground speed in forward or reverse.

“I did have one problem with the tractor. The original gas tank holds just three gallons which allowed me to go for only about three hours before I had to refuel. To solve the problem I mounted another 3-gal. tank on the left fender, ahead of the original one, and hooked them together.”

Best Buy

Kubota B8200 4-WD backhoe grader equipped + 1 more

Bill De Remer, Conneautville, Pa. · Vol. 25, No. 2 (2001), p. 17

“My best buy is my Kubota B8200 4-WD backhoe grader equipped with an 18 hp engine and 12-in. rear bucket. It does a nice job.

“My 1979 Massey Ferguson 285 tractor has only 670 hours on it and is still in like-new condition. I bought it equipped with a 54-in., 6-way hydraulic-operated blade, a 540 rpm pto, and a Cat. I 3-pt. hitch. I also use it with a 52-in. Woods Bros. rototiller, a used single shank subsoiler that’ll go 24 in. deep, and a 2-section spring tooth harrow. The tractor handles them all with no problems.”

Best Buy

Ram W200 3/4-ton 4-WD pickup + 1 more

John F. Carter, Manson, Iowa · Vol. 25, No. 2 (2001), p. 17

“My 1974 Dodge W200 3/4-ton 4-WD pickup has almost 130,000 miles on it. It has been in 40 of the 50 states and often hauls loads that weigh more than it does. It’s a great truck.”

“I inherited a 1985 Mercury Grand Marquis car from my mother and really like it. It now has about 160,000 miles on it and still gets almost 20 mpg. Both the car and the pickup start well in cold weather, even at temperatures down to 20 degrees below zero.”

Best Buy

New Holland 55 rake

George Strohmer, Woodstock, Md. · Vol. 25, No. 2 (2001), p. 17

“My best buy over the years is my 1955 New Holland 55 rake. I bought it in the crate for $385 and put it together myself. A dealer friend of mine joked that we could probably still buy the crate for $385. I’ve overhauled the gearbox and replaced quite a few of the teeth but I’ve raked thousands of acres with it and still use it every year. All the New Holland equipment we own are best buys.”