Real farmers rate what they bought, from FARM SHOW MagazineSubscribe  ·  Free issue  ·  Send us your Best or Worst Buy
Subscribe to FARM SHOW
Home › Issues › Vol. 40, No. 3 (2016)

Best & Worst Buys: FARM SHOW Vol. 40, No. 3 (2016)

56 reports from pages 12–15 · 49 Best Buys13 Worst Buys · See everything in this issue at FARM SHOW →

Best Buy

John Deere 5105M tractor equipped + 2 more

Fritz Groszkruger, Dumont, Iowa · Vol. 40, No. 3 (2016), p. 12

Fritz is the satisfied owner of a Deere 5105M tractor equipped with a 563 front-end loader. “After freezing for years in tractors without cabs we felt we had earned this great loader tractor. It has a slight delay going into reverse, which can be frustrating, but it’s probably safer to use that way. Also, the joystick’s plastic handle broke after five years of use.

“My LL Bean waxed cotton, down-filled chore coat is heavy and smells like an old Army surplus store. It provides great protection from the cold and wind (www.llbean.com; ph 888 615-9974). This company stands behind its products.

“I wish Gates Rubber Co. still made Green Wellies rubber boots. They came as medium or wide and mine lasted for two years. Then the company sold out, and I’ve found that boots made by the new company fall apart in just a few weeks. If anyone knows of a good boot to fill this niche, I’d like to hear about it. All the plastic boots and wet suit-like boots I’ve seen are either too hard or cause your feet to get hot.”

Best Buy

Case IH 370 Magnum tractor equipped

Gary L. Baker, Mechanicsville, Iowa · Vol. 40, No. 3 (2016), p. 12

“I help a farmer during harvest and operate a Case IH 370 Magnum tractor equipped with a CVT transmission. It’s the best tractor I’ve ever driven. It has plenty of power and I really like the transmission. It also has a great cab and rides like a luxury car.”

Best Buy

Pacer self-priming water pump + 1 more

Kirby Herman, Elizabethton, Tenn. · Vol. 40, No. 3 (2016), p. 12

“My best buy is a 2009 Pacer 2-in. self-priming water pump equipped with a 5 hp Briggs & Stratton engine (www.pacerpumps.com; ph 800 233-3861). This pump has had a lot of hard use but still starts on the first pull. It has paid for itself many times over.”

On the minus side, “My Eden Pure radiant heater doesn’t heat as large an area as advertised, and the bulbs on it don’t last long and are expensive to replace. The price of this heater has been reduced since I bought mine, but it’s still no bargain. I threw mine away after one year.”

Best Buy

Cinch Net slow feeder hay

Don Eenigenburg, Grant, Mich. · Vol. 40, No. 3 (2016), p. 12

Don’s the satisfied owner of a 2015 Cinch Net slow feeder hay net from The Hay Chicks (www.haychix.com; ph 715 483-1770). It can be used with square bales, round bales, or flakes and is designed to control the amount of hay horses are able to consume at any one time.

“I feed a small herd of beefalo cows and calves, along with a Belgian horse, and hate to see a lot of hay waste,” says Don. “At first I thought this product was priced a bit high, but not any more. My bales last 20 to 25 percent longer so the feeder has paid for itself in just a couple of months. I wish there was a faster and easier way to put the net on the bales, but I can live with that little struggle in return for the savings in hay waste.”

Best Buy

Chevrolet 1500 diesel pickup

Dave Kuipers, Arlington, S. Dak. · Vol. 40, No. 3 (2016), p. 12

“My 1990 Chevrolet 1500 diesel pickup has served me well while working construction jobs over the years. It has been to about two thirds of the states and now serves as my daily commuter. It has about 343,000 miles on it but for the most part has required only routine maintenance. It’s parked for the winter now, but I’ll bring it back out this spring.”

Best BuyWorst Buy

International Harvester 1026 Hydro tractor + 2 more

Fred J. Whipple, Chittenango, N.Y. · Vol. 40, No. 3 (2016), p. 12

“My 1971 International Harvester 1026 Hydro tractor has never been in the shop for repairs and is still going strong.

“I’m impressed with my Pronovost 104-in. 3-pt. mounted, double auger heavy duty snowblower. It really chews through big snowdrifts (www.pronovost.qc.ca; ph 418 365-7551).

“My 2011 Wood Gun E180S wood boiler requires too much maintenance. Ashes don’t come out of the cyclone as they should, and the fan motor quit working. The boiler loads up with creosote and smokes terribly whenever wood is loaded in. Also, the gaskets on it don’t last.”

Best Buy

John Deere equipment + 1 more

Vlietstra Dairy Farm, Kalamazoo, Mich. · Vol. 40, No. 3 (2016), p. 12

“Over the years we’ve been extremely happy with the performance of Deere equipment. However, we recently purchased a Deere 326 skid loader equipped with a hydrostatic transmission that’s noisy and stiff. Also, the transmission won’t go into low range unless the engine is turned off. Now no one wants to drive it so the machine sits unused in our barn.

“Our 2015 Case 210 skid loader runs smooth and quiet and is a pleasure to operate. Perhaps Deere could learn from this company just how to build a skid loader.”

Best BuyWorst Buy

GM Sierra 1500 Kodiak z71 crew cab + 1 more

Mac Campbell, Wilkesport, Ontario · Vol. 40, No. 3 (2016), p. 12

“It’s a pleasure to operate and is fuel efficient,” says Mac about his 2015 GM Sierra 1500 Kodiak Z71 crew cab pickup.

On the “worst buy” side, he lists his 2014 Dodge Ram 1500 quad cab 4-WD pickup equipped with an EcoDiesel engine. “I bought this pickup because it was advertised to get 30 mpg. However, a year after I bought it and with about 20,000 miles the EcoDiesel engine started hammering as if a main bearing had failed.

“The dealer told me to drive the pickup in for inspection, but I never made it because the engine blew about halfway there. He said metal shards in the oil filter had caused the oil pressure to drop, and he ordered a new engine on October 18. However, I didn’t get the pickup back until December 4 and by that time I already had my Sierra.”

Best Buy

My best buy is my smart phone

Bryan Van Kirk, New Galilee, Penn. · Vol. 40, No. 3 (2016), p. 12

“My best buy is my smart phone. Anytime I buy a new vehicle I take a photo of the VIN number or the vehicle’s model and serial number and then title it. It saves a lot of time when ordering parts.

“For example, one time I needed a new part for our refrigerator. To pull the refrigerator out far enough to read the model and serial numbers, I would have had to first disconnect the ice maker water supply line and risk breaking a fitting or stripping threads. But with my smart phone I was able to just reach in and take a photo of the numbers. Placing your phone on one of those ‘selfy sticks’ might come in handy for this kind of task.”

Best Buy

Cooper Mini Clubman equipped

Tom Korn, Danvers, Ill. · Vol. 40, No. 3 (2016), p. 12

A 2009 Cooper Mini Clubman equipped with a 1.6-liter, 4-cyl. engine and 6-speed manual transmission rates as Tom’s “best buy” (www.miniusa.com; ph 866 275-6464). The vehicle has comfortable seating for five, split rear doors that open with a foot-activated sensor, and an interior outfitted with what the company describes as premium materials and cutting-edge technology.

“I use it as a small work truck and also to run errands,” says Tom. “The fuel economy is excellent and is best at 2,900 to 3,100 rpm’s. It corners like a go-cart and is a very comfortable car to drive on long trips.”

Best Buy

Rubbermaid Big Wheel cart

Martin Havran, Saragosa, Texas · Vol. 40, No. 3 (2016), p. 13

A 7 1/2 cu. ft. Rubbermaid Big Wheel cart rates as Martin’s “best buy” (www.rubbermaidcommercial.com; ph 800 347-9800). “This push/pull-type handcart is well balanced and rides on big, flat-free tires. The design makes it easy to move heavy loads weighing up to 300 lbs., which is equivalent to about two days worth of manure on my farm.”

Worst Buy

Farm Pro chinese-made tractor

Dwight Holcomb, Acworth, Georgia · Vol. 40, No. 3 (2016), p. 13

Dwight’s disappointed with his Farm Pro Chinese-made tractor. “I bought this 30 hp tractor new and had it shipped from a Texas distributor. I also bought five pieces of equipment to use with it, which brought my total cost to about $22,000.

“The tractor came with a 4-year warranty but that isn’t worth a dime. There were multiple hydraulic leaks, a lack of power, and nothing on the tractor was tight. The first time I tried using this tractor to plow our garden my son walked behind me, picking up parts as they fell off.

“For warranty work the company suggested I go to a shade tree mechanic, and they said they’d pay up to $50 per hour. Our local tractor dealers charge much more than that, but they don’t want to work on this tractor because they know these tractors don’t stay fixed. And they’re unwilling to deal with the tractor’s warranty due to bad results in the past.”

Best BuyWorst Buy

Polaris

Armin Scripter, Abilene, Kansas · Vol. 40, No. 3 (2016), p. 13

“All three of my Polaris ATV’s run good, but their frames are nothing but junk and break easily due to poor construction. Also, the running boards on them keep tearing off.”

Best Buy

John Deere 5075E tractor during

J. Richard Mood, Mullica Hill, N.J. · Vol. 40, No. 3 (2016), p. 13

“We bought a new Deere 5075E tractor during the fall of 2013. In October 2015 the tractor had about 1,100 hrs. on it when the fuel tank melted. The dealer said he’d replace the tank if I paid for the labor, which cost me $518 including pickup and delivery. We then installed a piece of Teflon between the new tank and the tractor’s rear housing to keep the same problem from happening again.

“Also, when we drained the transmission oil it had a burnt, ugly smell. My next tractor may possibly be a Kubota.”

Best BuyWorst Buy

John Deere 1760 12-row planter + 1 more

Joe Wasson, Middletown, Iowa · Vol. 40, No. 3 (2016), p. 13

Joe’s the satisfied owner of a 2013 Deere 1760 12-row, 30-in. planter. “I ordered this planter with finger pickup corn meters instead of vacuum units. The planter’s adjustable bean meters work well, and the 3-bu. seed boxes save time in the field. I can plant a lot of acres in a day.

“I like my 2001 Massey Ferguson 6280 tractor except for the cheap European hydraulic couplers and the dash electronics. Also, many of the company’s replacement parts are priced too high. For example, it costs $200 for a toolbox, $120 for a hydraulic filter, $46 for an air filter, $500 for a starter, and $1,600 for a rear fender. Instead, I save money by buying most of my parts on the internet.”

Best Buy

Jeep Cherokee Trailhawk

Jonathan Dean, Baskin, La. · Vol. 40, No. 3 (2016), p. 13

“I couldn’t be more pleased with the 2015 Jeep Cherokee Trailhawk I bought for my wife. It has ample seating room, great cargo space, and a flawless 4-WD system. The V-6 engine has plenty of power, and the leather seating is top notch.”

Best BuyWorst Buy

Gearwrench 3/8-in drive ratchet + 1 more

Dennis Burkholder, Hopkinsville, Ky. · Vol. 40, No. 3 (2016), p. 13

A Gearwrench 3/8-in. drive ratchet and socket set rates as Dennis’s “best buy” (www.gearwrench.com; ph 800 621-8814). “It’s made with top quality craftsmanship. The ratchets have a 72-tooth gearhead which makes it easy to work in tight corners. The company offers a comprehensive lineup of metric and SAE sockets.”

On the “worst buy” side, he lists his Drill Doctor drill bit sharpener. “After I used it for a short time the grinding wheel slipped on the arbor, so when I tried to split the point it messed up the bit. The company sent us another sharpener right away, but after we used it a few times the same problem happened again.”

Worst Buy

ArcOne X540V welding helmets

Nathan at Red Rver Repair, Elkton, Ky. · Vol. 40, No. 3 (2016), p. 13

“We bought two ArcOne X540V welding helmets at about $210 apiece. These helmets have a nice fit and visibility, but after a short time one of them quit working properly. The dealer sent it back to the company for repairs. We had to pay about $100 for a new filter, which I think should have been covered by the warranty. Soon after that, both helmets quit working so we were out about $500.”

Best Buy

Chevrolet cars

Phil Harris, Milford, Mich. · Vol. 40, No. 3 (2016), p. 13

“I’ve always had good luck with Chevy cars and trucks until I bought a 2015 Chevy Equinox. My wife wanted this car because she has back problems and liked the seats in her friend’s new Equinox. The dealer offered an attractive price on an in-stock demo and she was ‘sold’.

“I commented to the dealer about the car’s poor ride, which I consider similar to that of a 2-ton empty truck, but he said it was due to the cold weather and bumpy roads. I think the horrible ride is due to springs that are way too stiff. As a result you can feel every pebble and tar joint in the road.

“The car is powered by a 4-cyl. engine and he said we’d get 32 to 34 mpg, but the best we’ve seen is 30 mpg. The car weighs more than 4,000 lbs., and driving in the mountains of Kentucky and Tennessee, the little engine has trouble keeping up with loaded semi trucks.

“Even though we don’t travel on dirt or muddy roads, the back end of the vehicle is always dirty due to the poor design of the tailgate. Road dirt also accumulates on the bottom of the door jambs due to tire splash and poor door-to-body seals.

“The car’s computer touch screen ‘infotainment’ center is very complicated to operate, even when the vehicle is parked. It’s too difficult and dangerous to use when you’re driving alone, and it has gone blank twice for several hours at a time. Two trips to the dealer to address this problem have both ended up labeled ‘no trouble found’. All these problems have been written up in magazines such as Consumer Reports and Motor Trend.”

Best BuyWorst Buy

Starkey hearing aids + 1 more

Lavier Schliefert, Deepwater, Mo. · Vol. 40, No. 3 (2016), p. 13

“I paid about $2,400 for my Starkey hearing aids, but in reality I think they’re worth about $150. I’ve had to make countless trips back to the store because the hearing aids either quit working or the sound level had to be raised or lowered. If I sweat a little or there’s high humidity or a little dust in the air, they shut down.

“I had a pair of MDHearingAids that cost only about $600 and they worked ten times better (www.mdhearingaid.com; ph 312 219-8422). The only reason I tried the Starkey’s was because I lost my MD’s and thought I might get something better to replace them. However, all I got was a problem.”

Best Buy

Kioti LK2554 23 hp tractor

Billie Leonard, Rathdrum, Idaho · Vol. 40, No. 3 (2016), p. 13

“The 1996 Kioti LK2554 23 hp tractor we bought used in 2003 is a great little tractor. We use it to skid logs, haul dirt, plow snow, dig post holes, rototill our garden, rake leaves and for many other jobs. We have seven different attachments for it. It’s the most used machine on our small farm, but it just keeps on running. No problems.”

Best Buy

Star Tron

Earl Lumbra, Montgomry Center, Vt. · Vol. 40, No. 3 (2016), p. 13

“I use Star Tron in all my gas for saws, 4-wheelers, and other small engines. It eliminates the problems I was having with ethanol in fuel (http://www.starbrite.com/startron).”

Best Buy

Car Cane

Rex Gogerty, Hubbard, Iowa · Vol. 40, No. 3 (2016), p. 14

“If you have a bad knee or other aches and pains, the Car Cane really helps get up and out of a car. It slips into the door latch bracket on any car and gives you a solid handle to push on. Stores in the glove compartment or side of the door. Also has a built-in flashlight, seat belt cutter and window breaker. Sells for about $15 on Amazon or you can go to the company direct (www.carcane.com).”

Best Buy

Hardy outdoor wood stove

Dave Wampler, Sidney, Va. · Vol. 40, No. 3 (2016), p. 14

“My Hardy outdoor wood stove with its 100-gal. water jacket has kept my home warm for 23 years. I haven’t spent a dime on fuel oil or propane. I have to split wood, but it’s worth it.

“It has 2 small circulating pumps and a fan, but those small motors hardly take any power to operate. They only turn on when heat is needed.

“I’m not alone in being satisfied with a Hardy furnace. I have at least half a dozen neighbors who also have Hardys. One has his tied into his hot air furnace. Mine supplies hot water directly to a baseboard heat system. I installed it and the stove when I built the house.

“I do have to haul wood, but with the help of a rebuilt manure spreader, that job is fairly easy. I removed the beater, put in a new bed, and reinstalled the drag chain. I also kept the hydraulic end gate. It is easy to bring a load of wood to the furnace, lift the gate and dump the wood with the drag chain.”

Best Buy

Willys jeep

Bill Reeks, Cromwell, Ky. · Vol. 40, No. 3 (2016), p. 14

“I’d be lost without my 1948 Willys jeep which helps me get all kinds of chores done around my place. It has a front hitch and lift boom so I can pull or push trailers around with it – including my log hauling trailer shown here. I use the lift boom alone to move smaller logs. A gas-powered generator rides in the back to power the 2,000-lb. winch on the front boom and to power a 16-in. electric chainsaw. I like the easy starting and operation of both the generator and chainsaw.”

Best Buy

VamPLIERS

Brad Miller, Ridgeville Corners, Ohio · Vol. 40, No. 3 (2016), p. 14

“Anyone who does any kind of mechanical repair work will love these pliers,” says Brad about the VamPLIERS made by Vampire Professional Tools (ph 949 748-0552; www.vampiretools.com).

“They’re designed to remove screws with stripped or rusted heads. Nothing usually wo rks short of drilling it out or using a special screw extractor, which can be a time consuming process.

“VamPLIERS are screw-extracting pliers with patented vertical and horizontal serrations on the inside jaws, which makes it possible to grab and turn a fastener without slippage.

“The pliers are made from treated high quality carbon steel. A variety of models are available.

“I’ve used my VamPLIERS to remove stove bolts, sheet metal screws and wood screws, and it has worked perfectly every time. Prices range from $17 to $49.”

Best Buy

Hudson bandsaw mill

John Houston, Davidsonville, Md. · Vol. 40, No. 3 (2016), p. 14

“I like my new Hudson bandsaw mill but the tracks that it’s mounted on are too flimsy. The tracks consist of two 6-ft. sections of welded-together 2 by 2 angle iron.

“I wanted to reinforce the tracks and make the sawmill easier to move around, so I bought another 6-ft. section of angle iron track and welded it onto one end. Then I used 3-in. sq. tubing to build a support frame and welded it onto the underside of the tracks. I also added tandem axle wheels to each side.

“The wheels, which came off a pair of small hand trucks, are supported by homemade axles. The wheels are spaced farther apart than necessary because I had earlier used them for another project. I mounted the hand truck’s handles on one end of the trailer so that I could move it around by hand, but the trailer proved to be too heavy. So I welded a coupler onto the other end so I can move it around with my skid loader.

“The portability really comes in handy. For example, if I get too much sawdust where I’m cutting up trees I can quickly move to another location. I use 4 jacks to keep the sawmill level on uneven ground. I spent less than $500, whereas a new trailer for the sawmill would have cost at least $2,000.”

Best Buy

Crary Wind System

David Fortenberry, Winnsboro, Louisiana · Vol. 40, No. 3 (2016), p. 14

Last year David mounted a Crary Wind System (CWS) on his MacDon FD75 40-ft. flex draper header (www.crary.com; ph 800 247-7335). He says it increased his soybean yields by at least 10 percent, which helped pay for the system in one year.

“The CWS uses a Crary 8-in. fan powered by a pto shaft to distribute air to a series of drop tubes to provide a high-velocity stream of air that pushes the crop from the cutterbar into the header. The forced air, which is adjustable from the cab, ensures that harvested grain moves into the combine, rather than falling to the ground.”

In 2015 he averaged 79.2 bu. per acre on 1,282 acres of soybeans. “We did numerous field tests on five varieties of soybeans on both dryland and irrigated fields, and were able to hold our yield losses at the header to 1 to 1 1/2 bu. per acre,” says Fortenberry. “That figure was consistent regardless of the moisture of the beans or the time of day we were in the field. The real eye-opener to us was in tests where we turned the system off and compared the losses without it - even though we were using a brand new draper header.”

Fortenberry used a foot-square frame to check header losses directly behind the header. “In an irrigated field that produced 103 bu. per acre, without the CWS we counted 20-plus beans per square foot behind the header. But in an adjacent strip with the air on, the losses were only 2 beans per square foot. Our combine manuals say two seeds per square foot equals a bushel-per-acre header loss, so you can see the difference running the air makes.

“If you’re seeing 12 seeds per square foot behind the header, that’s six bu. an acre you’re not getting paid for. Even with $9 bean prices, over our 1,282 acres it doesn’t take long to pay for the Crary system.”

In a dryland field with a 45 bu. per acre yield average, the difference was even more telling, he says. “There, we saw 32-plus beans per square foot (16 bu. per acre losses) behind the header without the CWS, and with it, only 2 beans per frame.”

Fortenberry says the tests showed consistent yield improvements with the CWS in beans of both 9 and 12 to 13 percent moisture. “On the drier beans, we were seeing 4 1/2 to 6-bu. losses without the air, but well under 2 bu. per acre with the air system running. In 12 percent moisture beans, we had about 5 1/2-bu. losses with the air turned off, but with the air on the losses dropped back under 2 bu. per acre.

“Several weeks after we finished harvest, the test areas where we didn’t use the CWS looked as if they’d been reseeded.”

The more efficient crop handling at the cutterbar also helped Fortenberry maintain his usual 5 to 5 1/2 mph harvest speeds, even on some custom fields with tall, lanky bean plants and heavy infestations of tall grass.

“The forced air blows the stems to the cutterbar where they can be cleanly harvested without shattering in contact with the reel,” he says. “I’ve even raised the reel up where it never touches the crop, and the air still puts the plants right where they belong for a clean harvest.

“Based on our experience with the Crary air system last year, I’d definitely buy another one.”

Worst Buy

John Deere 4050 4-WD tractor

Wayne Duerr, Avella, Penn. · Vol. 40, No. 3 (2016), p. 14

Wayne’s had problems with his 2015 Deere 4050 4-WD tractor. “The engine has a lot of pollution control equipment on it, and as a result just a few drops of water can cause it to lose power and, in some cases, shut down in the field. My daughter was driving the tractor one time when it shut down. They found sludge in the fuel tank, which I think was already there when I bought the tractor. Also, when too many particulates enter the muffler I have to stop and run the tractor at a certain speed until the muffler cleans itself out.

“I previously owned a Deere 2955 and it ran good, but I wanted a tractor with a cab so I traded it. I’ve owned a lot of good Deere tractors in the past including a B, two A’s, and a 2-cyl. diesel. My dealer tried to help but had no luck.”

Best Buy

Cub Cadet Big Country 2-WD utility vehicle equipped + 1 more

Billy Blackwood, Chapel Hill, N.C. · Vol. 40, No. 3 (2016), p. 15

“The best machine I ever bought is my 2006 Cub Cadet Big Country 2-WD utility vehicle equipped with an 18 hp, 2-cyl. Kohler engine and electric push button transmission. I paid $9,000 for it and still use it every day.

“It has a trouble-free engine that doesn’t use any oil and is easy on gas, and it always starts right up. The push button transmission also works great. I use this machine to check on our cows and to do fencing work and so forth. It’s light enough that I can drive across fields after heavy rains without leaving deep ruts, and the differential lock axle on it works great for getting around in snow.

“The machine sets low to the ground so it’s easy to get on and off. I wouldn’t change a single thing about this utility vehicle. It cost less than a Deere Gator or Bush Hog, and it handles better and is less noisy.

“I like my two Kubota M108S 4-WD tractors, both equipped with 4-cyl., 108 hp diesel engines and 16-speed transmissions. The 2011 model has a cab and front-end loader and has about 800 hours on it. The 2010 model has no cab and about 590 hours. I use these tractors mainly for haying work such as operating balers and haybines. I also use them to operate a 3-pt. mounted 200-gal. sprayer, a harrow, and a big field cultivator.

“Both tractors are excellent on fuel. They’re short and easy to maneuver, and they start well in winter. The cab model has a front-end loader which I use for handling round bales and feeding livestock. It’s amazing how efficient these tractors are and how well they operate.”

Best Buy

Montana 45 hp diesel tractor

Alice Goll, Nunica, Mich. · Vol. 40, No. 3 (2016), p. 15

Alice is the satisfied owner of a 2010 Montana 45 hp diesel tractor with cab, air conditioner and heater. “This tractor is great in every way. It handles really nice and is easy on fuel, and the cab is comfortable enough to work all day long.”

Best Buy

Allis-Chalmers B10 garden tractor

Dale Ridenhour, Nowata, Okla. · Vol. 40, No. 3 (2016), p. 15

“The 1966 Allis Chalmers B10 garden tractor I bought used last year for $250 equipped with a 42-in. mower deck is my best buy. I call it my ‘Little Allis’. Mechanically, the tractor was in good shape when I bought it. I replaced the points, plugs, and starter generator, changed the fluids, repainted the tractor, added stickers, installed new blades on the deck and added new tires and a new seat. The rear tires are 10 1/2 in. wide, which helps reduce wheel ruts. The tractor still has the original 10 hp Briggs & Stratton 1-cyl. engine.”

Best Buy

Goody Getter

Keith Martin, Alexandria, Minn. · Vol. 40, No. 3 (2016), p. 15

“My wife and I looked at many different nut crackers, trying to decide which worked best. We wanted primarily to crack black walnuts, which are really tough. We found s e v e r a l n u t crackers designed just for black walnuts, but they were expensive.

“We were leery of trying a product we had never seen before, but all the research we did on the Goody Getter, including watching videos on their website and communicating with the inventor, convinced us to give it a try (www.grandpasgoodygetter.com; ph 417 833-2421). It cost less than $90, including shipping, and has worked flawlessly. We have to keep it oiled and greased periodically, but it’ll crack any nut with ease. It comes with 2 different rams which self-adjust as the machine is operated, allowing us to crack nuts very quickly. The rams cut rings around the top and bottom of the nut, causing the nut’s shell to fall away and expose the meat.

Best Buy

Kroil penetrating lubricant

Robert Marshall, Somerset, Mass. · Vol. 40, No. 3 (2016), p. 15

“I think Kroil penetrating lubricant is the best on the market (www.kanolabs.com; ph 800 311-3374). You can buy it in an aerosol can or by the gallon. It never lets me down. Wherever there’s corrosion, this oil will work through it.”

Best Buy

Udderly EZ + 1 more

Trudy Zalewa, Floyd, Va. · Vol. 40, No. 3 (2016), p. 15

“My Udderly EZ helps me milk my goats quicker and keeps the milk contained so it stays cleaner (www.udderlyez.com; ph 800 287-4791). It’s available either as a hand-pumped milker or with an electric pump to milk two teats at a time, and it works on cows, goats and sheep.

“On a small scale, our drill-powered Power Plucker saves us time on the days when we butcher (www.powerplucker.com; ph 417 423-0385). It works fast and will pluck a scalded chicken in 90 seconds or less.”

Best Buy

John Deere 5100E + 1 more

Delfina Castillo, Post, Texas · Vol. 40, No. 3 (2016), p. 15

“It’s a great tractor with a lot of power, but it has some problems,” says Delfina about their 2013 Deere 5100E. “The front end is too high to see the rows in the field, and the steps are too high to climb. Also, the door on the cab is difficult to open.

“My Deere 3038E utility tractor works great, but whenever I use it to shred weeds or operate a tiller I wish it had a cab.”

Best Buy

Ford 9N tractor

Herbert Paul Gradney, Perris, Calif. · Vol. 40, No. 3 (2016), p. 15

“The 1953 Ford 9N tractor I bought used in 1992 is my best buy ever. It always starts and mostly has required only routine maintenance. I’ve replaced the front tires and radiator as well as spark plugs and plug wires. I’ve owned other tractors over the years, but none of them could ever replace my little Ford 9N.”

Best Buy

New Holland Boomer 40 loader tractor

Garry Elliott, Haverhill, N.H. · Vol. 40, No. 3 (2016), p. 15

“I love my 2012 New Holland Boomer 40 loader tractor. No problems. I use it to plow snow and even in the coldest weather it always starts. I have yet to use the block heater. During summer I use this tractor with a small backhoe, a 5-ft. bush hog, a 2-bottom plow, hay rake and hay forks. It handles 900-lb. round bales with ease. I highly recommend this tractor.”

Best Buy

Honeywell These lights use 42

Dave Allers, South Haven, Mich. · Vol. 40, No. 3 (2016), p. 15

“I recently went to Sam’s Club and bought six 4-ft. LED shop lights made by Honeywell. These lights use 42 watts each and produce 4,500 lumens of light, and they have a life expectancy of about 50,000 hours. The lights cost $36 apiece and are easy to install. They work fantastic. I like them much better than my old neon 4-ft. shop lights, which constantly needed new bulbs.”

Best Buy

Ford 5000 tractor

Jack Essary, Taneyville, Mo. · Vol. 40, No. 3 (2016), p. 15

“I bought my Ford 5000 tractor used 35 years ago, and the hour meter on it broke 25 years ago at 6,700 hours. It’s the best tractor we’ve ever owned. We use it to operate our round baler and to do lots of other dirty jobs, with no problems at all. I’d buy a new one just like it if I could.”