Oregon battery-powered pole-type chainsaw
“The motor on my Oregon battery-powered pole-type chainsaw is at the mid-point so the saw is well-balanced. It works great to trim branches off hedge trees without having to get into the thorns.”
68 reports from pages 12–15 · 61 Best Buys13 Worst Buys · See everything in this issue at FARM SHOW →
“The motor on my Oregon battery-powered pole-type chainsaw is at the mid-point so the saw is well-balanced. It works great to trim branches off hedge trees without having to get into the thorns.”
“Cub Cadets have changed over the years. They went from being a premium brand of yard tractor to just ordinary. The first change was when they started having an overseas company built them to IH specs. The next change was installing a Chinese-built engine in many of them. I’m sorry for people who buy a new Cub Cadet thinking they are getting the quality and value of the original Cub Cadet.”
Photo: FARM SHOW“The used MacDon FD75 draper head we bought this year does a fantastic job harvesting beans and works smoother and more efficiently with much less field loss than the Deere 30-ft. auger platform we had before.”
Read the whole story →Read more at FARM SHOW →“I grew up on a farm with only Massey tractors and currently have 6 of them. But in 2014 I bought a used MF 2625 4-WD with 677 hrs. from an individual in Georgia who only used it for light work at a boat marina. He had bought it new from a Massey dealer.
“This spring while using the tractor for light lawn work, clouds of white smoke started coming out of the engine. When I shut off the engine, I heard a gurgling sound. I took it to the dealer who determined the problem was likely a leaking head gasket. The tractor had just 1,182 hrs. When they disassembled the engine, they found severe rust and corrosion in the cooling system. Chunks of rust the size of grapes came out. They said it was the worst case of rust and corrosion they had ever seen. After cleaning the radiator, it leaked like a sieve. The water pump had to be replaced because it couldn’t be cleaned. The dealer had trouble getting all the rust out of the engine.
“I talked to Massey/AGCO managers about the problem and they said coolant should be replaced at 2,000 hrs. but this tractor only had about half that. Since the warranty time had elapsed, they said they had no responsibility in the matter.
“I’d like to hear from any reader who has had a similar experience with a Massey tractor.”
“Norwex window cloths and detergent work great for cleaning windows (www.amazon.com). We have a 16-sided museum on our farm with lots of windows so it’s important to us.”
“I noticed in your last issue that a fellow wrote in to say he was happy with his Drill Doctor for sharpening drill bits. I also bought one several years ago along with a converter that lets you sharpen oversized bits in the machine. I have been more than satisfied with the purchase. I was a heavy mechanic for 31 years and have many sets of carbide and titanium drill bits. Drill Doctor does an absolutely wonderful job of sharpening them.
“Two years ago, my wife gave me the Ken Onion edition of the Work Sharp knife and tool sharpener. I must say I’m thrilled with this sharpener. I’m a perfectionist when it comes to sharp knives and tools, and this sharpener fills the bill completely. I have drawers full of previous knife and tool sharpeners in my shop and have discarded them all in favor of the Ken Onion sharpener. It quickly puts a razor sharp edge on knives, scissors and any other blades, using a series of 5 belts, the finest being 6000 grit.
“Both of my ‘best buy’ products are made by the same company in Oregon and they are very good at making quality-built products at reasonable prices.”
“I bought my old faithful Chevy C-60 snowplow truck years ago at a city surplus auction. We live on a township road about 1/4 mile from a state highway. After a big snow the highway gets cleared but often the township road stays plugged for 2 to 3 days. The 10-ft. blade on this truck, which has a 427 engine and 5-speed transmission, gets the job done fast. I have new chains on the front tires tires to help with steering and braking.”
“I’m 90 years young and love grading dirt. I’ve found out over the years that not everyone can do that well. I bought a Bobcat tractor a while back to grade with but soon after I got it they had to split the tractor because someone had left a bolt loose inside. Otherwise, it’s been a good machine. I’m going to keep on grading as long as I can.”
“I have saved hundreds of dollars over the past 50 years by using Frantz by-pass oil filters in my vehicles (www.frantzfilters.com). It removes particles down to 2 microns in size so I never drain the oil, I just replace the filter element inside the filter housing and add oil as needed to top up. Oil doesn’t wear out, it just gets dirty. If it’s not dirty, you don’t need to change it.
“When these filters first came out, people used rolls of toilet paper as the filter element. But Frantz developed an improved filter media that cleans 10 times better. It’s an amazing filter that’s easy to install and really protects engines. I used to be a dealer for it but at age 82 I don’t do that any more. But I still believe in the product.”
“I have mixed reviews regarding my Lowery farm equipment. I have had several pieces of Lowery equipment over the years with few problems. However, when I had a problem with the safety shroud over the pto shaft on my Lowery Clipper 400 rotary mower, I made many calls to the company and even wrote a letter to the president but was unable to get replacement information. No help at all from the company.”
Photo: FARM SHOW“The Vat 15-gal. pasteurizer (www.thevatpasteurizer.com; ph 800-236-3956) is a best buy for my cheesemaking business, Mystique Chèvre.”
Read the whole story →Read more at FARM SHOW →“It’s a pleasure to operate and has greatly reduced my mowing time,” says Earl about his 2019 Deere Z540R zero-turn riding mower. “I use this mower with a mulching kit that activates with the flick of a lever. This machine turned out to be a nice complement to my 2016 Deere X590 garden tractor which I use with a mower deck, leaf bagger, and snowblower. The snowblower had a belt problem, but otherwise it’s a really nice outfit.
“One of the best small pieces of equipment I own is the tank-type air compressor I bought new in 1957. It was made by E.L. Smith and Sons. It has performed flawlessly with occasional use, and I think the secret to its long life is that I let the air out of the tank after each use. The compressor is still in its original condition.”
“I’ve used Amsoil lubrication products for 10 years with excellent results. Their 2-stroke engine oils are by far the best on the market and eliminated the problems I used to have with fuel quality. Amsoil small engine oil also works great.
“I’ve put about 126,000 miles on my 2012 4-WD Ford Escape equipped with a 3-liter engine. The 4-WD works great on ice and snow-covered roads, and the engine gets better than rated fuel economy with plenty of power. I think one of Ford’s biggest mistakes was getting rid of their 3-liter engine. The vehicle’s body shows some rust, but that’s to be expected in Minnesota.
“The only vehicle I like better than the Ford Escape is my 1990 Buick ATB LeSabre, which is equipped with a bullet-proof 3.8-liter engine. I bought the car used at about 60,000 miles, and when I finally sold it at about 268,000 miles the engine and transmission had never been touched. The new owner ended up with almost 300,000 miles before the body gave out.
“My 2018 Lincoln Electric TIG 200 Square Wave welder works great for both AC/DC stick and TIG welding, so I’ve been able to use it on several different projects. It has simple controls so anyone can make excellent welds. I have about 30 years of welding experience in industrial applications and have used welders that cost many times more than this one, but they didn’t work any better. It makes excellent welds on aluminum.”
“My best buy 2004 Power Trac 22 hp. tractor was previously featured in FARM SHOW (Vol. 42, No. 2). It needed some repair work recently so I returned it to the company’s headquarters in Tazwell, Va. They had the tractor for a week and took it completely apart. They welded all the stress cracks caused by metal fatigue, repacked all the hydraulic cylinders, pressure-checked the hydraulic pumps and rebuilt them as needed, checked the wheel hydraulic motors and rebuilt them as needed, replaced any bad hydraulic hoses, checked all the bolts and fittings, installed a new wiring harness and ignition switch, rebuilt the foot pedals, drained and added 10 gal. of hydraulic oil, and power washed and repainted the entire tractor. I think they would have replaced the engine if necessary.
“It was like getting a brand new tractor at a fraction of the cost. This is a small family-owned company that builds tractors as well as mining equipment. Excellent customer service (www.power-trac.com; ph 800 843-9273).”
“My Deere 3320 35 hp. loader tractor runs great and has a lot of power for its size. I use it with a winch for skidding logs and pulpwood.”
Edwin says his Bush Hog 2561 zero-turn riding mower is well-engineered and works great. “I replaced a drive belt, but otherwise this machine has required very few repairs.
“My Stihl MS261 chainsaw has never started right, and it burned up two fuel combustion chambers but I can’t get help from the company. I’ve owned 4 other Stihl saws without any problems.”
Frank has put more than 300 hrs. on his 2012 LS J2030H backhoe loader equipped with a 30 hp. Mitsubishi engine. “I had owned a Case IH 235 tractor equipped with a Mitsubishi engine, and it performed flawlessly. The only issue so far with this machine was a minor problem with the dash electronics, which was promptly resolved. I’m 80 years old and find the loader bucket is really handy around our farm. Works great to move logs.”
Photo: FARM SHOW“My home-built posthole cleanout auger, which was featured in FARM SHOW (Vol. 43, No. 3), really came to my rescue this fall.”
Read the whole story →Read more at FARM SHOW →Dan’s the satisfied owner of a 2004 72-in. Dixie Chopper zero-turn riding mower equipped with a Generac engine. “I bought this mower used from a Deere dealer for only about half the cost of a comparable Deere model. It has 345 hrs. on it. I had problems with grass clippings plugging the radiator cooling fins and overheating the engine, and had to remove the entire shroud to completely clean the clippings out. On the positive side, the mower works as fast as advertised.
“I’ve had good luck with Justice Brothers engine oil treatment (www.justicebrothers.com). I had an old auger operated by an 11 hp. engine that burned a lot of oil loading and unloading semis, and also smoked a lot. After adding this oil treatment the engine didn’t smoke any more, and burned only about a third as much oil. The engine was probably on its last legs anyway, but because of the oil treatment I was able to keep the auger going for another 3 years or so until I parked it for good.
“I had problems with the 2016 Frigidaire refrigerator we keep in our garage. The repairman who came out says this model has factory defects that prevent it from working properly in cold weather, even though the refrigerator is advertised as being ‘garage ready’. I tried to return it under warranty but was told it was working properly. I got no satisfaction.”
John is the satisfied owner of 3 Polaris recreational vehicles – a 2017 Sportsman single seat ATV; a 2014 Ace 4-WD single seat UTV; and a 2014 Ranger 4-WD side-by-side UTV with cab. All 3 models came with the same Mod 570 cc engine and accessories.
“I’m 89 years old so the Ace UTV is special for me because of its foot accelerator and steering wheel, mini cab, and rollbar. The Sportsman ATV has a lot of power for its size and holds well on hills, and I like the Ranger side-by-side UTV for its versatility.”
Cecil owns a 1954 Ford Golden Jubilee (also known as the Ford NAA). “This tractor may be old but it has performed great over the years in all respects. I changed the electrical system from 6 to 12 volts which makes the tractor easier to start.”
Glenn likes his Milwaukee M18 cordless 1/2-in. impact wrench. “It has plenty of power enough to twist off 9/16-in. bolts - and the batteries last a long time. My M18 cordless drills work just as good.
“My Toro 5000 zero-turn riding mower equipped with a Kohler EFI engine does a good job of mowing, but the engine doesn’t want to start in colder weather. It turns over for a while, then fires and dies repeatedly before it eventually will run. The dealer replaced the fuel pump and reset the engine control module, then said the engine was ready to go. I got the machine home and let it set for a couple of weeks, but when I tried to start it the same problem happened again.”
“I’ve got about 100,000 miles on my 2001 Dodge 2500 pickup equipped with a Cummins diesel engine, and my only expenses have been for oil changes and fuel filters. It still has the original brake pads.
“My Can-Am Spyder Outlander motorcycle is extremely difficult to work on, and required special tools that the company doesn’t even sell. Can-Am dealers charge $250 to install a new battery, and I paid $872 just for an electrical switch, including installation. The motorcycle kept going into limp mode, indicating low oil pressure, so the dealer replaced a sensor and the oil pump but it didn’t help. He finally disassembled the engine and then claimed it was ‘worn out’, even though it had fewer than 5,000 miles on it. I changed the oil every 1,000 miles.”
He bought a used 2005 Deere 4320 tractor equipped with a Bush Hog loader, with 185 hrs. on it. It now has about 600 hrs. “The tractor itself works great, but the loader had problems. I had to rebuild the hydraulic cylinders twice, and it looks like I’ll have to again. The Bush Hog dealer has no answers. A new cylinder from Bush Hog costs several hundred dollars, and I’m not sure I want to take another chance on buying one.”
“My Pneu-Dart gun works great to treat livestock remotely with drugs or medications (www.pneudart.com; ph 866 299-3278).
“The 1989 JCB 160 skid loader I bought used in 2003 stands up to hard use and always starts right up. I’ve replaced just the water pump and gone through 4 sets of tires.
“I can’t find parts for my 2014 Howse 10-ft. rotary mower or my 2013 Tonutti disc mower.”
Jerry bought a used 1941 Farmall M tractor in 1960 when he started farming, and is still using it. The engine was overhauled for the second time in 2014. “This was the only tractor I owned for many years, and I used it with a cultivator, corn picker, mower, and front-end loader. It’s still the first tractor out of our shed and is always ready to go.”
“After trying a variety of different traps to catch moles, I’ve gone back to using an old spear-type Victor mole trap which I modified a bit (www.victorpest.com; ph 855 584-2867). Keeping moles down requires constant patrolling, but it can be done. I’m not able to set the new spear-type mole traps because they’re very awkward and user ‘unfriendly’. My Victor trap still works good and was made right here in the U.S.”
“I bought my 2015 Stihl MS230C chainsaw just before my 80th birthday and really like it. This saw has gone through several bars and numerous carbide-tipped chains. It’s easy to start and very dependable. Works great.”
“The starter I bought at NAPA Auto Parts for my 2002 Dodge diesel pickup came with a lifetime guarantee but lasted only about 5 years. The company wouldn’t honor the guarantee because they said I didn’t have an account with them. I’m not a farmer and don’t own a business, and I pay with a check or cash so my name wasn’t in their computer files. To prove ownership, I would have had to spend a lot of time searching for a cancelled check or receipt going back several years. I think a lifetime guarantee should last more than 5 years. I finally bought a new starter at O’ Reilly Auto Parts, where I was able to get a real guarantee.”
“The Amana microwave oven I bought new in 1997 still works like new.
“I use a METALpro 45-ton iron worker with attachments in my shop. It works great and I think everyone should have one (www.metalprocorp.com; ph 262 679-0504.”
“Our Massey Ferguson 283 tractor equipped with a Massey Ferguson A10 loader is easy to service. We use this little ‘bulldozer’ to push and pack silage in our trench silos.
“I bought a used 2004 Dodge 3/4-ton diesel pickup with about 185,000 miles and it hasn’t had any problems.
“I use my 1988 New Idea 5209 disc mower to cut about 250 acres of hay per year. The hitch on this mower isn’t pretty, but the mower cuts great.”
“My 1979 Deere 2840 tractor always starts, has a lot of power, and is easy on fuel. However, the brakes push down hard.”
“My wife and I have greatly enjoyed riding our 1999 Harley-Davidson Low Rider motorcycle. It’s very reliable and has more than 160,000 miles on it.”
“My 2008 Mercury Grand Marquis is a dependable, solid car. Very comfortable and fuel efficient.
“My 1991 Murray 30-in. riding mower still runs good. One time the magnets fell off the machine’s starter, but my neighbor used Gorilla Glue to reattach them.”
“My 2015 Stihl M5251C chainsaw always starts no matter what the weather is like.
“My Husqvarna chainsaw wouldn’t start if the saw was warm. I also had problems with my Husqvarna walk-behind mower. A mechanism underneath it was wide open and plugged up with grass, which caused the mower to finally quit running.”
He isn’t happy with the NITO Terra Grabber tires on his 2011 Chevrolet 3/4-ton diesel pickup. “They’re supposed to be a premium tire, but within 17,000 miles 3 of the 4 tires showed tread separation. The company rep said they had come out with new tires with an improved design, so I bought a set. However, in less than 25,000 miles two of the tires began to separate. I’m almost 75 years old and don’t drive fast. There have been no wheel alignment problems with this pickup, and I check tire air pressure regularly. So no more NITO tires for me.”
Leroy’s happy with his Lapp heavy-duty aluminum dumper wagon (www.lappwagons.com; ph 717 733-2117). Measuring 30 in. wide by 60 in. long by 13 in. deep, the wagon has a capacity of 15 cu. ft. and can handle loads weighing up to 2,000 lbs. It comes with a tractor “hitch and handle” combination.
“This wagon is a must have for small farms,” says Leroy. “We use ours almost every day to haul firewood, sawdust, manure, mulch, and more. It dumps easily with an overcenter tipping design.
“Our DR Power 30-in. brush mower works great to keep brush trimmed around our wooded property. Briars don’t have a chance when this mower hits them.”
On the “worst buy” side, he lists his DR self-propelled lawn mower. “The self-propelled mechanism goes so slow that we almost have to push the mower to get anything done. I called the company and they sent an older model transmission which was supposed to make the mower go faster, but it didn’t help. It wasn’t long before the self-propelled mechanism quit working entirely. Now all we have is a push mower.”
A Larson storm door rates as his “worst buy”. “While remodeling our kitchen, we installed a 42 by 80-in. entrance door, and after some time passed we decided to add a storm door. Larson was the only company we could find that makes special order storm doors, and they sell them only through Lowe’s home improvement stores. Larson wouldn’t ship the door to us so we had to drive 40 miles one way to Lowe’s to pick up the door.
“Soon after installation, the door started sagging at the top hinge. The aluminum frame on the door was only 3 in. wide, and the door’s full-length thermal glass window was very heavy. I complained to Lowe’s but they said I had to contact Larson. With no phone number available - because Lowe’s wouldn’t release Larson’s customer service number - I had to write a letter to Larson. However, the company never replied so after 90 days or so I again contacted Lowe’s.
“By this time the miters on the corners of the door were cracking and since the door was starting to bind on the latch side, I had to move the latch frame over to allow the door to close. Lowe’s said that by doing that I had voided the warranty and there was nothing they could do, except order a new door at my expense for about $850.
“At that point I decided to beef up the door on my own, since it was out of warranty anyway. I jacked up the latch side to take the cracking out of the door and installed a 1/4-in. steel gusset at each corner, using 8 screws to hold the door up. I needed a new sweep for the sill and had to drive to Lowe’s to order it in person – another 80-mile round trip. Then when the sweep came in I had to drive back to the store again and pick it up.
“Meanwhile, the brass door handle on the outside had lost its plating and looked bad, so I had to drive to Lowe’s again to order a new one and then make yet another trip to pick it up. I wanted to buy a nickel-plated door handle, but Lowes said I had to buy a brass one because that’s what the door came with. I’m completely disgusted with both Lowe’s and Larson.”
John’s the satisfied owner of a Stihl MS362C chainsaw. “I wasn’t real excited about this saw at first. It had a great chain brake and compression release, but it still started hard. However, once I got the saw going it cut through wood like a beaver on steroids. It starts better now, too.”
On the “worst buy” side, “I expected too much when I bought a can of Flex Seal. My fault.”
“My Milwaukee Fuel 18-volt, 1/4-in. cordless impact driver works great. Most of the company’s Fuel class tools work great – they’re lightweight, built strong, and last a long time.
“My Milwaukee 18-volt cordless grease gun was an exception, though. It was defective so the dealer sent it back for repairs. The company sent a new grease gun but it didn’t work either, so the dealer sent it back and gave me a replacement. However, I’m still not getting the hang of using this tool and since a lot of the bearings are enclosed and sensitive to the amount of grease being applied, I’ve scrapped it and gone back to a tried-and-true hand pump grease gun. I own many Milwaukee cordless tools that work great, but this isn’t one of them.”
He likes the Lynxx 40-volt cordless pole saw he bought at Harbor Freight. “It cuts tree limbs up to 12 in. diameter with no problems, and the battery lasts about 2 1/2 years. After cutting a large tree down I just stand back and trim the branches off. I think a pole saw is much safer than tripping over branches with a chainsaw.
“I bought a Vulcan ladder at Harbor Freight for $99, and it works as good as other ladders that sell for $200 or more.”
“It’s amazingly powerful and cuts as fast as my Stihl MS290, yet it weighs only 11 1/2 lbs.,” says Jamisen about his Makita 18-volt cordless LXT brushless chainsaw equipped with a 14-in. bar. “This saw runs quiet and always starts. Makita’s new twin battery series tools use the same batteries found in their 18-volt tools. I like how this saw performs.”
A Korean war veteran, Lynn says an old Hughes H-5 helicopter he found in a barn is his “best buy”. “The helicopter hadn’t been flown in 39 years. I hauled it home and replaced the fluids, gave the engine a tune-up, and adjusted the rotor. Now it flies and handles extremely well.
“My Husqvarna 2654 lawn tractor equipped with a Kohler 26 hp. engine is my worst buy. At 33 hrs. the engine locked up, even though the oil had recently been changed at 26 hrs. I learned later that the engine had been recalled because of some problems.”
“I use my Milwaukee M18 brushless Hackzall reciprocating saw on both wood and metal, and find that it reduces my pruning time by two thirds or more. The batteries last a long time, and are interchangeable with the company’s M18 cordless drills and impact wrenches.
“I installed a Trimble EZ Steer assisted steering system on my old Steiger tractor. The system turns the steering wheel for you by combining a friction wheel and a motor with guidance from any compatible Trimble display. It worked so well that I also bought a system for my White 155 tractor, which I use with our soybean planter.”
On the minus side, he lists his Raven Cruizer II SmartSteer auto steering system. “We had constant problems getting the light bar to work with the steering node. The company should have recalled this product. I was constantly on the phone talking with various dealers, tech people, and Ag Express Electronics. The Raven system did a good job when it worked, but unfortunately it worked only about 40 percent of the time.”
“We like the way our 2008 Deere 9760 combine performs. It’s simple to operate. However, it has a Mexican-built engine with hydro-locking problems. The head gasket leaks due to poor machining of the block, which allows the piston cavities to fill with anti-freeze. Deere changed the specs on this engine so they say it’s not their fault and won’t help. The same combine with a Waterloo engine has a .5 percent failure rate, compared to a 40 percent failure rate for the Mexican-built engine.
“While our combine was in the shop, we saw 3 other combines with the same Mexican-built engine. The engines had been torn down and all of them had the same hydro-lock failure. The company’s block person was no help at all. I told him I would be happy if I could buy the parts at cost to make my own repairs and his reply was, ‘Why would Deere want to do that?’ I also asked if the shop was going to let Deere know about the hydro-lock problems and he gave the same reply.
“This was not the service I expected from Deere, and I was very disappointed. We’ve been loyal Deere customers for more than 80 years, but from now on we’ll look at all brands. Deere is becoming just like the car and truck companies. They’re more worried about their stock holders than their customers.”
“My 2018 Chevrolet Colorado 4-WD pickup looks and rides great. It’s fuel efficient and has a back-up camera, which I really like.
“My Kubota 28 hp. zero-turn riding mower equipped with a 6-ft. deck does a great job. It has about 1,800 hrs. on it but is still going strong.”
They’re disappointed with their 2008 Chevrolet 2500 HD pickup. “The bed is so high off the ground that it’s difficult to use the space properly. This pickup has less than 100,000 miles on it, but is already on its sixth set of tires. Also, when starting out, the driver has to get the engine up to 2,000 rpm’s before the transmission will shift up to the next gear, which makes it hard to get moving.”
“I’ve been buying Harbor Freight tools for at least 40 years, and have noticed they now provide a better choice of power tools and shop equipment than in the past. The hand tools are also of better quality, and new stores are popping up everywhere. Harbor Freight tools have saved me a lot of money over the years. Check out their new tool cabinets on wheels - they’re as good as you’ll find anywhere.”
“I’ve put about 1,200 hrs. on my 1995 Deere 445 diesel-powered garden tractor. It has a lot of power and 4-wheel steering, which makes it easy to drive. However, after about 20 years the engine became very hard to start and lost full power. I took the tractor to our local Deere dealer and after about a week I got a call. They said the tractor needed a complete engine rebuild that would cost about $3,500. I said no way, and brought the tractor back home.
“I looked the tractor over and discovered the linkage rod on the fuel shutoff solenoid had come apart. Over time the rod had backed out about an inch and the engine was starving for fuel. I screwed the rod back in place and now the tractor starts and runs fine. It cost me $150 for the dealer to tell me I needed an engine rebuild that wasn’t needed.”
“After my Husqvarna 2-cycle gas trimmer wore out, I bought a Ryobi Expand-It 40-volt cordless power head and string trimmer attachment. The fully charged lithium ion battery lasts a long time - almost as long as it takes to use up a tank of gas. By the time the battery runs low and needs to be recharged, I do too. So I take a break while it’s charging.”
“My 2004 Deere GT245 garden tractor equipped with a 20 hp. engine and 54-in. deck is very reliable. I use it every week to mow our 5 acres of grass and brush on very rough terrain, and the chassis and deck have held up well. The engine has lost some power, but after almost 1,000 hrs. you expect that. I use Gator blades on the deck, which are a huge improvement over the factory blades (www.oregonproducts.com; ph 800 223-5168). Wet grass clippings don’t clump up on them as much.”
His 2007 Ford Focus hatchback has about 240,000 miles on it but still doesn’t use any oil. “I’ve never had a vehicle run so well for so long without requiring any major repairs,” he says.
Jeff’s disappointed with his Cleary 60 by 80 pole shed. “The roof leaked from day one. I can see nails that missed the purlins and water also comes in through the ridge cap. I always know when it’s raining outside because it also rains inside.”
“My 2019 Husqvarna YTH 1842 riding mower cuts fine, but when I first engage the blades it sounds like a 60-year-old threshing machine starting up, powered by an antique Huber tractor. I think dealers should be able to demonstrate their products before selling them so we don’t get surprises like this after we buy.”
Sam likes his 2019 WoodMaxx 8800 pto-operated wood chipper (www.woodmaxx.com; ph 866 943-7209). “I own a small Christmas tree operation and also live on a wooded lot. This wood chipper works great to handle any wind storm damage and to clean up tree limbs.”
Seth likes the Lenox Metal Max 4 1/2-in. diamond edge cutting wheel he uses on his angle grinder. He bought it at a NAPA Auto Parts store. “I’ve had good luck with Lenox metal cutting blades over the years. This one cuts clean and smooth, and it doesn’t produce clouds of smoke and dust like fiber disc cutting wheels do.”
“I replaced the seats on my Kubota 4700 and 5700 M series tractors with Grammer seats sold by K&M Mfg. (www.tractorseats.com; ph 800 328-1752). The original seats on these tractors are nice, but over time their suspension system wears out. All my tractors have open stations so the seats don’t last as long as they would in a cab.”
“I like my Timberline chainsaw chain sharpener (www.timberlinesharpener.com; 208 405-2020). It mounts right on the bar so I don’t even have to remove the chain. It cuts every tooth the same and does a really nice job.”
He has a problem with the 2017 Maytag washing machine he bought at Home Depot. “During the spin cycle the clothes get twisted up so you can’t get the moisture out.”
“I use my 2002 Deere lawn tractor to mow our 2-acre lawn, mulch leaves, and blow snow. It still has the original battery, which I think is outstanding.”
“I like my 2009 6-ft. Bush Hog flail mower with the ‘rockhopper’ feature. This clutch system works great when you hit an obstacle. No problems.”
He’s disappointed with the Carlisle lugged tires on his small tractor. “They’re tubeless tires with thin sidewalls. The problem is that over the winter the tire pressure dropped and the tires went flat because the sidewalls cracked and leak air. I guess it’s time to switch to tube tires.”
Larry’s impressed with the Drop ’N Locks frame-mounted gooseneck hitch he uses on his Ford F250 pickup (www.gooseneckhitch.com; ph 866 368-4826). The hitch bolts on under the bed using existing holes in the pickup’s frame. There are no under-truck levers to pull or bind up. The operator lifts a steel wedge to release the ball and then pulls the ball out of the socket, rotates the ball, and replaces the wedge. When the hitch is folded under, the pickup bed is clear with no obstruction.
“It works great and has no moving parts to wear out. It’s made by a small Kansas company that offers super friendly service,” says Skoglund.
“My best buy is my Big John 25-gal. boomless ATV sprayer (www.bigjohnmfg.com; ph 800 658-4471). “It has electronic controls and can cover lots of ground fast.
“The 1975 Ford Ranger pickup my wife inherited just keeps on going, with good fuel economy and very few repairs. It’s old so it looks pretty rough, but it does what we want.”
“My 2018 Central Boiler Titanium Series furnace was my worst buy. I paid about $12,000 for it. I had the furnace installed in early winter but was able to use it for only about 3 weeks. I asked the dealer to return my old furnace and described the problems I was having with this one. He told me the wood I was burning was too wet. So I bought kiln-dried wood but still had to babysit the furnace every 2 hrs. or so through the coldest 2-week stretch of winter.
“I finally bought a Mountain Mann outdoor furnace for about half the price (www.earthoutdoorfurnaces.com; ph 417 926-4136). I’ve been told to place the Central Boiler furnace out by the road and sell it, but I can’t do to someone else what was done to me.”
Harve’s had good luck with Blue Devil Hydraulic Stop Leak which he bought at a NAPA Auto Parts store. The company says it’s designed for use in all hydraulic systems and creates a permanent seal to restore dried, cracked, and shrunken rubber seals.
“The power steering gearbox in my 2000 GM C6500 pickup was leaking about a half gallon of oil per week. I had read about this product in FARM SHOW so I thought I’d give it a try,” says Harve. “The oil stopped leaking right away, and I haven’t had to add any in 6 mos.”
“Len’s impressed with his 2017 Harbor Freight 4-gal. backpack sprayer. “It’s well-built and works flawlessly. Sells for 50 to 75 percent less than comparable name brand sprayers.”
Mark nominates his 2016 Land Pride 6-ft. rototiller as a “worst buy”. “We grow vegetables in 40-in. beds and I bought this machine to till them. I removed enough outside tines to leave a 40-in. tilling width. However, even with the machine’s depth shoes set as deep as possible I could only get the tines to penetrate 2 to 3 in. There was about 1 1/2 in. of clearance between the tines and the rototiller housing, so I installed longer tines. That gained about an inch of penetration depth, which at least allows me to break open a sod field. However, I still can’t use the rototiller for finish tilling. I have to use our Mitsubishi 40-in. tiller to do that. Now I’d like to buy another Mitsubishi tiller, so if anyone knows where I can get one please contact me.”