Real farmers rate what they bought, from FARM SHOW MagazineSubscribe  ·  Free issue  ·  Send us your Best or Worst Buy
Subscribe to FARM SHOW
Home › Issues › Vol. 24, No. 2 (2000)

Best & Worst Buys: FARM SHOW Vol. 24, No. 2 (2000)

77 reports from pages 14–17 · 69 Best Buys16 Worst Buys · See everything in this issue at FARM SHOW →

Worst Buy

General Motors C-60 + 1 more

David Cornea, Morse, Sask. · Vol. 24, No. 2 (2000), p. 14

David’s very disappointed with his 1997 General Motors C-60 (Topkick) semi truck equipped with a Caterpillar 3116 diesel engine. He received the truck in April, 1999, over a year after ordering it. “After I got it, everything worked okay until winter arrived. Then the engine ran terrible, with enough blueish-white smoke to make my eyes water. The truck’s acceleration was very poor. As the engine warmed up the problem disappeared which made it hard to diagnose. The GM dealer told me to go to the nearest Caterpillar dealer.

“The Caterpillar dealer replaced a thermostat, replaced fuel filters, and pressures were tested. I thought my problem was solved, but the worst was yet to come. A belly tarp was suggested by the factory and cardboard was put in front of the radiator. The mechanics rotated the air filter housing assembly to draw warmer air closer from the radiator. Numerous seemingly inconclusive tests were made to the engine. Another new thermostat was put in. The fuel injector was replaced and adjustments were made to the timing. Exhaust temperature tests were made. Cat wanted me to purchase, for $2,200, an exhaust brake to load the engine so I could maintain warmth to the engine in the city, for example.

“In my case, CAT made what I term ‘band aid’ solutions. I can accept that a company makes a lemon every so often. The difference is in how they handle the problems. My best experience with this truck was when I sold it last November.

“I was lucky, because this vehicle was not used as my primary source of income. I can’t help but think what would have happened if it had been a Caterpillar tractor or combine. Heaven help anyone with a $350,000 combine and a lemon engine.”

Best Buy

Ford 3600 tractor equipped

David Swartz, Edinburg, Va. · Vol. 24, No. 2 (2000), p. 14

“Our best buy is a 1975 Ford 3600 tractor equipped with a diesel engine. I bought it used in 1991 with about 700 hours on it. We use it for custom garden plowing, tilling, Bush Hogging, and chores on our small farm. No major problems. It now has more than 2,300 hours on it.”

Best Buy

John Deere 702 8-wheel rake

Wes Suddarth, Lebanon, Tenn. · Vol. 24, No. 2 (2000), p. 14

Wes is impressed with his 1999 Deere 702 8-wheel rake. “It rakes clean and cuts my raking time in half. In good hay it’ll stay ahead of two round balers. It makes even, fluffy windrows with minimal leaf loss and doesn’t twist and ‘beat’ the hay as much as a rollbar rake does.”

Best BuyWorst Buy

Massey Ferguson tractors + 1 more

De Bo Jacks, Mountville, S.C. · Vol. 24, No. 2 (2000), p. 14

“My best buys over the years have been my Massey Ferguson tractors. I’ve owned 1105, 1085, 285, 175, 275, and 265 models. All of them have been reliable and fuel efficient. None has ever failed to start in cold weather even though I don’t use starting aids.

“My worst buy is my 1994 Yamaha Kodiak 400cc 4-wheeler ATV. It won’t start in cool or cold weather, even with a new battery. The front end is on its third set of bearings, even though I rarely drive it in mud. All I use it for is to check fences. It was supposed to have sealed brakes, but I’ve lost count of how many brake shoes I’ve had to replace. The front and rear differential came from the factory full of steel shavings. I’ll never buy another Yamaha product.”

Best Buy

Gleaner R52 combine

Terry Spezia, Davison, Mich. · Vol. 24, No. 2 (2000), p. 14

“I’m well pleased with my 1996 Gleaner R52 combine. Its design allows me to shell corn on side hills without the grain shifting to one side, and without having to pay for the added cost of a regular side hill combine.”

Best Buy

Rawson zone till cart + 1 more

Steve Weisbrod, Canastota, N.Y. · Vol. 24, No. 2 (2000), p. 14

“It’s built extremely heavy and works great in hard soil and in rocky conditions,” reports Steve, impressed with his 1997 Rawson zone till cart which he mounts ahead of his Deere 6-row planter (Unverferth Mfg., Box 35, Kalida, Ohio 45853 ph 419 532-3121; Website: www.unverferth.com). “It has three wavy coulters per row which provides excellent tillage and germination. It allows true one-pass planting.

“My Clean Burn waste oil furnace burns clean and runs trouble-free. It’s better than free heat because you don’t have to pay for oil disposal.”

Best BuyWorst Buy

Ram 2500 4-WD pickup + 1 more

Charles Crossman, Ortonville, Mich. · Vol. 24, No. 2 (2000), p. 14

Charles likes his 1998 Dodge Ram 2500 4-WD pickup which has an 8,800-lb. gross vehicle weight and is equipped with a 360 cu. in. gas engine. “The engine performs great. It always starts even on the coldest mornings, and it pulls wagons loaded with 200 bales of hay like they weren’t even there.

“My worst buy is my Weigh-All gauge for front-end loaders. I paid almost $300 for it. It’s supposed to tell me the weight of whatever’s in the bucket. However, the gauge readings are all over the place.”

Best Buy

Case 1370 tractor + 1 more

Richard Mason, Rising Sun, Md. · Vol. 24, No. 2 (2000), p. 14

“I’ve had good luck with my Case 1370 tractor of which I’m the third owner. Only a few things on it have had to be fixed including the air conditioner, fuel gauge sending unit, and 3-pt. lift cable. It’s hard to believe, but the DEKA batteries in this tractor have been there since 1988.”

Best Buy

Classic outdoor woodburning stove + 1 more

Byron Ruge, Valparaiso, Ind. · Vol. 24, No. 2 (2000), p. 15

Byron nominates his Classic outdoor woodburning stove (Central Boiler, Greenbush, Minn.), as his “best buy”. “This is the third heating season I’ve used it and I’m still impressed with how efficient it is. The company hasn’t overrated this stove at all. I have to fill it with wood only once every two days. I use it to heat an old 1,200 sq. ft. farm house with very little insulation. It also heats all my hot water. I just finished building a 40 by 70 by 14-ft. workshop and I intend to heat this building with the same stove.

“My Rawson 6-row coulter cart for zone-till planting is a best buy. I’ve been zone-tilling for 11 years now. I don’t want to think about all the money and time that I spent on equipment and fuel prior to zone-tilling. I feel that if you approach this system with the right management ideas and commit to making it work, you’ll succeed. I have not suffered any net income loss with this system. I may sacrifice a couple of bushels of yield, but I’m much farther ahead income-wise.”

Best Buy

K&M Mfg + 1 more

Richard MacDonald, North Manches-ter, Ind. · Vol. 24, No. 2 (2000), p. 15

Richard installed a 4-step SureGrip non-slip step made by K&M Mfg. on his International 1486 tractor. “Along with the hand rail they’re adjustable for your step height. Makes it much easier and safer to get in and out of the cab. I also installed a new Case-IH air ride seat, which is very comfortable and adjustable and makes the tractor ride much smoother. I fitted it with Goodyear DynaTorque radial tires. They’re excellent.”

Best Buy

Ford F-250 pickup equipped

Leo Shinholt, Corriganville, Md. · Vol. 24, No. 2 (2000), p. 15

“Leo’s 1989 Ford F-250 pickup, equipped with a 7.3-liter International diesel engine and a 5-speed transmission, has about 250,000 miles on it and is still going strong. “It’s a wonderful pickup. I use it hard and often pull a gooseneck trailer. I’ve changed the oil on it every 3,500 to 4,000 miles. Everything on it is original except for the tires, three sets of brakes, one water pump, a fuel pump, and a power steering pump.”

On the minus side, he lists his 1999 Ford F-250 pickup equipped with a 7.3-liter International turbocharged diesel engine. “The engine works great and the truck is well-designed. However, the 6-speed transmission leaves something to be desired. It’s very noisy. The company says these transmissions are just noisy and there’s no cure. Not a very satisfying answer.”

Best Buy

Chevrolet Cheyenne 3/4-ton pickup equipped + 1 more

Claude W. Winters, Eglon, W. Va. · Vol. 24, No. 2 (2000), p. 15

“Our 1997 Chevrolet Cheyenne 3/4-ton pickup equipped with a Vortex V-8 engine has been a dream. No problems after 3,700 miles. It can easily pull a low boy trailer loaded with equipment.

‘My 1992 Deere Gator is one of the greatest labor savers on the farm. I use it for checking, mending, and building fence, taking tools to the field for repairs, and just for getting around our West Virginia hills. It’s also a wonderful toy for our grand kids.”

Best Buy

best buy” Husqvarna 672 chain saw equipped + 1 more

Michael N. Bailey, Lancaster, S.C. · Vol. 24, No. 2 (2000), p. 15

Michael owns a “best buy” Husqvarna 672 chain saw equipped with a 20-in. bar. “This is the first saw of this size that I’ve owned. It has a lot of power which works great for cutting large trees. Overall, I’ve been pleased with all the Husqvarna equipment I’ve owned which includes three other saws and a leaf blower.

“I’m not happy with the 7.3-liter International Navistar engine in my 1990 Ford F-250 heavy duty pickup. Five months after the warranty expired a head gasket blew, and the same thing happened the next year almost to the day. One year later there was trouble again. This time cracks developed in one of the heads and about half the valve guides were worn out. We thought we fixed it, but right on cue this January the engine started running hot again and with a compression leak into the cooling system. That’s four years in a row with a repair bill each time of about $1,200. All routine oil, filter, and other maintenance has been done by the dealer on schedule. The pickup only has about 82,000 miles on it. I bought this engine because I believed it would be fuel efficient. I learned last year from reading FARM SHOW that the engine was a converted gas engine. If I had known this I would never have purchased it. I’d buy another Ford pickup, but not one equipped with one of these diesel engines.”

Best Buy

John Deere 345 garden tractor equipped + 1 more

Lee Sudman, St. Marys, Ohio · Vol. 24, No. 2 (2000), p. 15

“My Deere 345 garden tractor equipped with a trailer/bagger is my best buy. I love the handling ease, quiet running water-cooled engine, and reduced mowing time.

“My 1998 Deere 6400 tractor equipped with a cab has a very low noise level in the cab and is equipped with handy, easy-to-use controls. I like some of the little features it has such as step placement, grab bars, etc. My wife says a woman must have had a hand in its design.”

Best Buy

John Deere 6210 2-WD tractor equipped + 1 more

Galen R. Wenger, Lititz, Pa. · Vol. 24, No. 2 (2000), p. 15

“Our best buy is a 1999 Deere 6210 2-WD tractor equipped with a Power Quad transmission. It starts great in cold weather, has a lot of traction, and has plenty of power to get through tough spots.

“Our 1974 Deere 4430 tractor is also a best buy. It has more than 8,200 hours on it but just keeps running. Like they say, ‘Nothing runs like a Deere.’”

Best Buy

John Deere 6400 4-WD tractor equipped

D.L. Williamson, Philippi, W. Va. · Vol. 24, No. 2 (2000), p. 15

“I like my 1998 Deere 6400 4-WD tractor equipped with a Power Quad shuttle shift transmission, 640 front-end loader, and cab. “It’s an excellent loader tractor. I use it mostly to pull a discbine and a baler and to feed my livestock. It has about 1,000 hours and the only problem was a fitting that blew off a hydraulic line. The dealer promptly replaced it. The loader has quick-tach brackets that let me change from one piece of equipment to another in five minutes or less. I use a bale grabber, bale forks, pallet forks, post driver and bucket on the loader. The transmission has a park setting, which I really like.”

Best Buy

Ford New Holland 8670 front wheel assist + 1 more

Jimmy Stephens, Wingo, Ky. · Vol. 24, No. 2 (2000), p. 15

“We’ve used this tractor for five years with no problems,” says Jimmy, pleased with his Ford New Holland 8670 front wheel assist tractor. “It has the best transmission of any tractor on the market and is user friendly.

“Our 1997 Chevrolet 1500 4-WD pickup is equipped with a 350 cu. in. engine. It has a lot of power and is very fuel efficient.”

Best Buy

Honda Fourtrax 400 ATV + 2 more

William Corson, Jr., Newark Valley, N.Y. · Vol. 24, No. 2 (2000), p. 15

William says his 1998 Honda Fourtrax 400 ATV is his “best buy”. “It’s real handy and a good workhorse. We use it on our farm almost every day. It saves a lot of walking.

“Our Gehl 1475 round baler makes nice, tight bales.

“Our Melroe Bobcat 751 skid steer loader works great and has a grapple fork that works slick on round bales.”

Worst Buy

Red Wing shoes

Keith E. Haynes, Enoree, S.C. · Vol. 24, No. 2 (2000), p. 15

“Recently there have been ‘worst buy’ reports in FARM SHOW about Red Wing shoes. I’ve always had outstanding service from these shoes. They last about three times longer than the cheaper brand I had been using. The only problem is that they’re high priced.”

Best BuyWorst Buy

Kubota 3350 4-WD tractor equipped + 1 more

Harold R. Stoudt, Hamburg, Pa. · Vol. 24, No. 2 (2000), p. 15

“It’s a reliable tractor that’s easy to operate and well built,” says Harold, happy with his Kubota 3350 4-WD tractor equipped with a diesel engine, shuttle shift transmission, and frontend loader. He bought it used. “The diesel engine starts well even in cold weather. The only problem is that the front wheel assist seals leak fluid.”

On the negative side, “I purchased my Ryobi leaf blower to blow dust out of radiators on tractors, hay balers, etc., as well as to use in the yard. After several hours of use it refused to start. It required ignition work. Disassembling it is a terrible job. Now the carburetor has problems. It needs new parts but they’re not available locally.”

Best Buy

Zetor 2-WD 65 hp tractor

Rick Wineinger, Salem, Ind. · Vol. 24, No. 2 (2000), p. 15

“My Zetor 2-WD 65 hp tractor is my best buy. It’s really fuel efficient. Working in hay (mowing, raking and moving round bales), it uses only about one gallon per hour. It has about 600 hours on it. So far, so good.”

Best Buy

Welty hay panels

Perry Hathaway, Claypool, Ind. · Vol. 24, No. 2 (2000), p. 15

“My best buy are Welty hay panels which I use to feed round bales to my cattle (Welty Enterprises, 911 East Waterford St., Wakarusa, Ind. 46573 ph 800 628-4728). The panels are available in various lengths and can be tied together at the corners to make a square or rectangle. I used two 16-ft. long panels and one 8-ft. long panel and put them together in a rectangle shape, with one end open at the fence line. The design eliminates the need for a loader tractor. I simply drive my pickup or truck up to the fence line and roll the bale off. Cows eat from the sides, with very little waste. The panels are well made.”

Best BuyWorst Buy

Gleaner R-72 combine + 1 more

Tom Small, Walton, Ind. · Vol. 24, No. 2 (2000), p. 15

Tom’s impressed with his 1998 Gleaner R-72 combine. “Last year I ran an 8-row, 30-in. corn head and a 500 series bean head, and it was the easiest, most trouble-free harvest I’ve ever experienced. It always produced a good threshing sample. The biggest challenge is being able to use the machine to its full capacity. The cab has great comfort and visibility.”

On the “worst buy” side, he lists his 1997 White hopper bottom grain trailer. “The axles aren’t aligned correctly so the trailer pulls off center. The door openers require a lot of effort, and the wiring on it wasn’t standard. Also, the brakes are very sensitive to adjustment. I guess you get what you pay for.”

Best Buy

A-1 Agri Sales & Service

Van Meek, Birmingham, Iowa · Vol. 24, No. 2 (2000), p. 15

“My best buy is an 8-bale trailer built by A-1 Agri Sales & Service (1140 Gillan Road & Hwy. 63 South, Moberly, Mo. 65270 ph 660 263-0390). The frame is built of heavy steel pipe and rides on a semi trailer axle with dual 10.00 by 20 wheels. It’s nearly indestructable. I can use either a drop pin hitch or a pintle hitch. The 3-pt. bale spear on my tractor has a hook on it. I just back up the tractor and hook onto the hitch, then pick up the trailer and go.”

Best Buy

Toyota Tundra pickup equipped + 1 more

Jim Haines, Bremen, Ind. · Vol. 24, No. 2 (2000), p. 15

Jim likes his 2000 Toyota Tundra pickup equipped with a V-8 engine. “This is the third Toyota pickup I’ve owned. This one rides as well as my Cadillac Deville car and has a lot of power. I couldn’t be happier.

“I use my Deere 6 by 4 Gator every day on our farm and hunting preserve. It’s the most used piece of machinery on our place. We just love it.”

Best Buy

New Holland 116

Ted Watson, Eriksdale, Manitoba · Vol. 24, No. 2 (2000), p. 15

Ted’s the satisfied owner of a 1993 New Holland 116 14-ft. Haybine. “It’s an all-around terrific haying machine. I’ve had to replace only two drive chains. I use it to cut all my wild hay as well as my alfalfa.”

Worst Buy

John Deere 5400 tractor

Phillip Knight, Louisville, Ky. · Vol. 24, No. 2 (2000), p. 15

“My worst buy ever is my Deere 5400 tractor which I bought used in 1996 with 125 hours on it. At 922 hours the B range shaft seized to the pinion shaft, and I couldn’t get the tractor out of gear. A company representative said there were problems with some of these tractors because they weren’t assembled properly at the factory, but wouldn’t recall them because there weren’t enough complaints. My total cost for repairs was $4,450. The company agreed to pay only one fourth of the cost.”

Best Buy

Ford F-250 Supercab 4-WD pickup

Michael B. McCormick, Malta, Ohio · Vol. 24, No. 2 (2000), p. 15

“Other than a few minor problems that were taken care of by the dealer, it has been trouble-free,” reports Michael about his 1997 Ford F-250 Supercab 4-WD pickup. “It has a 460 cu. in. engine and a 4:10 rear end which gives it plenty of power. I really like the extended cab. It has plenty of room for our two small children as well as my wife. The only negatives are that it’s not too easy to get into the rear seat, a problem that has been taken care of on the new series models. Also, it could be more fuel efficient. It gets only about 10 mpg. Overall I’m well pleased with it. I’d definitely buy another one, especially the new series. I like them very much.”

Best Buy

Woods 3-pt finishing mower

Curt Varney, Prophestow, Ill. · Vol. 24, No. 2 (2000), p. 16

“My 1995 Woods 3-pt. finishing mower is my best buy. It makes a 6-ft. cut and does a fine job. I use it to cut large areas around our farmstead and to cut along each side of our lane. It has three blades and caster wheels on all four corners. I use it on my Ford 960 narrow front tricycle-type tractor, which is highly maneuverable.”

Worst Buy

Cummins diesel engine

Carl Zismer, Maquoketa, Iowa · Vol. 24, No. 2 (2000), p. 16

“My worst buy is the 1997 Cummins diesel engine in our Gleaner R52 combine. It has 180 hours on it. The problem is that it leaks oil -I scooped several shovels full of greasy dirt out of the engine compartment. The dirt even gets into the combine’s cleaning shoe. There’s a puddle of oil at the blowby pipe, too. I don’t know how this problem will be resolved. It’s still under warranty.”

Best Buy

Grasshop-per mower

Sandra Livesay, Mountain Home, Ark. · Vol. 24, No. 2 (2000), p. 16

“Our best buy is our 1998 25-hp. Grasshop-per mower with a Kubota engine and 61-in. deck. This is the second Grasshopper we have owned and they’ve both been flawless. When my husband first brought one home, I was skeptical because it looked so strange, with the deck on the front. But after driving it, I’d never cut grass any other way. We have a 6 1/2-acre yard and we normally cut grass from early March till November, so the machines get a workout.

“I had problems with a recent car purchase and I think my experience might help others avoid a problem in the future. What happened is that I bought a 1999 Toyota Camry LE. Our previous 1992 Camry had lumbar seats so I asked the salesman if this one did too. He said yes so we went ahead and bought it. After we got it, we found out it did not have lumbar seats and that they only come on the model with leather seats. We’ve been talking to the sales manager but all they do is give us the name of a shop where we can pay to have the lumbar added. My suggestion to other car buyers is to not take the word of sales people when making such a substantial purchase. Either check it out yourself, or get it in writing.”

Best Buy

John Deere 425 all-wheel steering riding

Jim Merriman, Deckerville, Mich. · Vol. 24, No. 2 (2000), p. 16

“We’re pleased with our Deere 425 all-wheel steering riding mower. We have about 3 acres to mow and there are at least 150 trees of various sizes to work around. Before we bought this mower, we spent as much time trimming as we did mowing. Now we do nearly all of it in one pass. I’m amazed at how well this machine maneuvers and how easy it is for new drivers to learn to drive it. Maintenance hs been virtually non-existent, some of which is because we keep the blades sharp and the underside of the deck clean.”

Best Buy

Toyota

George Schneider, Oakland, Calif. · Vol. 24, No. 2 (2000), p. 16

“In a recent report, Merdith Ewing said this about his Volkswagen pickup: ‘I’ll probably never own a pickup as good as this one again.’ I’d like to say he can if he wants to do some work.

“There is a pickup that Toyota makes in South Africa that’s built to get 300,000 miles. They are Toyota Landcruiser pickups and all you have to do is figure out how to get one into the U.S. I’ve talked to Toyota representatives about it and they won’t talk about it. They say they already sell everything they can make as fast as they can make it. I recently talked to a dealer in Zimbabwe and he said, ‘If you figure out how to get it into the U.S., I’ll get you one.’

“The 4-WD Landcruiser pickup has a solid front axle, a standard cab, a full-size long bed, and a 4.6 liter 6-cyl. Diesel engine. Gas engines are also available. The body and bed are made of sheet metal four times heavier than any U.S.-built trucks.

“Best of all, the truck sells for $25,250 U.S. for the loaded version.

“ If anyone figures out how to get these out of Africa, please let me know.”

Best Buy

General Electric

Alan Maclean, Kingston, Ontario · Vol. 24, No. 2 (2000), p. 16

“Our best buys are both General Electric products. We have a vertical fire GE LA20 oil furnace that’s been in service since 1947. That’s 52 winters. We also have a GE 180 amp AC welder that we bought in 1952. It’s still in use nearly every day.”

Best Buy

Massey Ferguson 285 tractor

Paul & Calvin Dentz, Iroquois, Ont. · Vol. 24, No. 2 (2000), p. 16

“Our Massey Ferguson 285 tractor, bought in 1983, has been split so many times I think it should have been built with a quick-disconnect system at the transmission. It’s about as dependable as a scud missile and only slightly less costly. Major repairs have included replacing the rear planetaries, the pto clutch and splines, one front and two rear transmission bearings, and the 3-pt. internal lift cylinder. We also rebuilt the fuel injection pump and fixed the pto brake four times. That’s about $13,000 worth of repairs on a $24,500 tractor along with endless downtime. All we’ve ever gotten from Agco is a ‘You bought it, it’s your problem’ attitude.”

Best Buy

Ford 8N tractor

George A. Wojnar, Cream Ridge, N.J. · Vol. 24, No. 2 (2000), p. 16

“One of my best buys is my Ford 8N tractor. It runs as good as new and looks like new, too. This 8N could easily work day after day, but it doesn’t have to. Just owning it brings back memories of old machinery, old ways of doing things, and people that were good to me when I was growing up. I feel lucky to own this 8N.”

Best Buy

DR trimmer/mower equipped + 1 more

Jared W. Jamison, Quinter, Kan. · Vol. 24, No. 2 (2000), p. 16

“I like my 1998 DR trimmer/mower equipped with a 5 1/2 hp Kawasaki engine. We use it to mow around buildings, calf hutches, etc., where there might be junk steel or large rocks that could damage conventional mower blades. It does a good job of cutting 2 to 3-ft. high weeds and grass.

“We’ve had a lot of trouble with our 1990 Polaris 350 4-wheeler ATV. It fouls out spark plugs quite often. It’s powered by a 2-cycle liquid-cooled engine and is chain-driven. We don’t like that combination. There are much better 4-wheelers on the market.”

Best Buy

Design of Weldments

Doug Garvin, Fairview, Pa. · Vol. 24, No. 2 (2000), p. 16

Doug nominates the book “Design of Weldments” as his “best buy” (The Lincoln Electric Co., 22801 St. Clair Ave., Cleveland, Ohio 44117 fax 216 361-5901). It sells for $10. “Anyone who welds should have a copy. The subjects covered and the presentation of the material is unique. You don’t have to be an engineer to learn from this book. It’s better than any other welding textbook I’ve seen.”

Worst Buy

Bourgault 2115 air seeder cart

Dwayne King, Hanley, Sask. · Vol. 24, No. 2 (2000), p. 16

Dwayne’s disappointed with his Bourgault 2115 air seeder cart. “I purchased this machine new and have never been able to seed canola with it. It’s impossible to calibrate the planting rate on it. It jumps from 6 lbs. to 12 lbs. to 2 lbs., etc. I’ve made several calls to the dealer and the manufacturer with no response. The manufacturer says they can’t update every machine out there.”

Best BuyWorst Buy

Case-IH double drill hitch + 3 more

Andy Mroczek, Honeoye Falls, N.Y. · Vol. 24, No. 2 (2000), p. 16

“Our Case-IH double drill hitch lets us pull two 10-ft. grain drills at once. When we were looking to upgrade our grain planting equipment, our neighbor mentioned how ridiculous it is to use a 80 to 100 hp tractor to pull just one grain drill. The hitch lets us cover 20 ft. in each pass so the acres go by a lot faster. By simply flipping a hydraulic lever we can fold the drills in place behind the tractor for transport, one behind the other, so they’re no wider than one drill.

“We really like the Unverferth residue cleaners that we mounted on our Deere corn planter. They not only clean in front of the row units for more accurate seed placement, but they also push rocks away from the gauge wheels. They’ve saved us many hours of labor by preventing damage to the wheels. Also, the seed boxes no longer seem to jump up and down as much which means the seed is being placed at the proper depth.

“Our Farm Aid feed mixer is a best buy (Corsica, S. Dak.). We’ve used it for six years to feed total mixed rations twice a day to our 115 cows with almost no down time. The only parts we’ve had to replace were the feed-out chain and a couple of bearings on the feed-out conveyor. The mixer is made with simple and common parts.”

On the negative side, “We had to install new packer rollers on our Kewanee culti-mulcher after the old ones wore out. The manufacturer was bought out by Bush Hog, which would not help us when we had a problem with the new rollers. The rollers have notches that are designed to mesh and lock the wheels together so that they all turn at once. The problem is that when the rollers were cast, the notches were made thinner which allows them to climb over each other. That causes the rollers to wobble and push off the snap-ring that holds the stack on the shaft.

“Our dealer couldn’t get the Bush Hog rep to take a look at our problem. The next purchase we make, we’ll be sure to find out if anything on it comes from a Bush Hog company and, if it does, we’ll have to rethink our options.”

Best Buy

Greenleaf Tech-nologies + 1 more

Stephan Janos, Somerville, Ohio · Vol. 24, No. 2 (2000), p. 16

Stephan likes low pressure Turbo Drop XL venturi nozzles made by Greenleaf Tech-nologies. He used them last year for the first time. “I bought them because they’re supposed to reduce spray drift. I was very happy with them. I had to spray on some windy days, but the spray didn’t drift. Weed control was good, but not great because it was very dry here last year. I think these nozzles will pay for themselves in a very short time.

“I bought a gas-powered Weed Eater leaf blower to keep my combine clean and blow trash off the radiator. It works great – in fact I wish I’d bought it years ago. A lot of my ground is a long way from an air compressor, but I don’t need one to operate this unit. I also use it to blow trash off the radiator. It’s priced under $125. My only wish is that it weighed less.”

Best Buy

Volkswagen Passat car equipped

Raymond Swenson, Brooks, Minn. · Vol. 24, No. 2 (2000), p. 16

Raymond’s impressed with his 1997 Volkswagen Passat car equipped with a diesel engine. “It handles excellent, accelerates well, has fantastic fuel efficiency, and runs quiet considering it has a diesel engine. We also own a 1981 diesel-powered Volkswagen which has more than 420,000 miles on it but still runs good. It still has the original rod, main bearings and pistons. New rings were put in it once.”

Best Buy

Chevrolet 3/4-ton 4-WD pickups

Joe D. Hostetler, Fredericksburg, Ohio · Vol. 24, No. 2 (2000), p. 16

“We’re well pleased with our two Chevrolet 3/4-ton 4-WD pickups, which are both equipped with 6.2-liter diesel engines. One’s a 1982 model and the other a 1992 model. They’re dependable and durable work trucks, yet they handle and ride well on the open road. The 1982 model has 210,000 miles on it and the 1992 model about 136,000 miles. We’ve always used Amsoil synthetic oil in these trucks which we think provides extra protection.”

Best BuyWorst Buy

Massey Ferguson 1130 D tractor equipped + 1 more

O. Douglas Holland, Bedford, Va. · Vol. 24, No. 2 (2000), p. 16

“I like my 1972 Massey Ferguson 1130 D tractor equipped with a multi power transmission. No problems after all these years. It’s easy on fuel, steers easy, and has a lot of hydraulic capacity.

“My worst buy is my 1979 Massey Ferguson 2745 tractor equipped with a V-8 diesel engine and 24-speed transmission. I had to replace the fuel injection pump and injectors and lines, as well as the clutch and pto bearing. The transmission had to be repaired twice. The tractor is hard to steer whenever I drive slow or back up to hook up to equipment. If I shift from low to high range on-the-go, the transmission locks in neutral. It’s a big problem to fix.”

Worst Buy

John Deere 5400 tractors

Jack L. Rarig, Catawissa, Pa. · Vol. 24, No. 2 (2000), p. 16

Jack’s “worst buys” are his two 1995 Deere 5400 tractors. “The first one was returned to the factory for evaluation of the transmission only three weeks after I got it and with only 19 hours on it. The hydro reverser transmission went from 10th forward to 9th reverse one day as we returned home from baling hay. The dealer told me he had never heard of anything like that before, but then two days later he told me about another Deere 5400 with the same problem. Both tractors were sent back to the factory for repairs.

“When I asked the dealer how long the repairs would take, he said several months. Parts had to be manufactured in Japan and then shipped to Waterloo. I traded this tractor in on another new 5400 which was delivered in August of 1995. Five minutes after it was off-loaded I noticed the first of many defects. With the engine stopped, the 3-pt. lift arms dropped visibly from full-up to full-down in less than a minute. With the engine running, the lift arms would raise to full height and bounce around. After a few seconds, the lift arms would drop a couple of inches, then bounce back up. When an implement was attached to the 3-pt., the bouncing was bad enough to raise the front wheels off the ground which made steering difficult, especially on hard surfaces.

“With less than 100 hours on the tractor more problems showed up. An air induction hose between the turbocharger and air intake became saturated with oil. The horn won’t blow. The engine produces white smoke up to 1,200 rpm’s whether it’s hot or cold, and it uses about a quart of lube oil every 10 hours. The brakes chatter and clank and both rear axle seals leak. Both ends of the steering cylinder leak, there’s no breather in the front axle, at times I can’t shift into any gear, anti freeze pushes out of the over flow, and the fuel gauge doesn’t work. The link between the third remote valve and lever snapped off at the press fit end.

“This tractor has now spent more hours on back of a truck than it has in my fields. Every time they return the tractor after warranty repair work there are loose and missing nuts and bolts, missing parts, and numerous nicks and scratches in the paint.”

Best Buy

Mazda B4000 extended cab pickup

Stanley Davis, Live Oak, Fla. · Vol. 24, No. 2 (2000), p. 17

A 1998 Mazda B4000 extended cab pickup rates as Stanley’s “best buy”. “I’ve owned several Mazda vehicles, all with good results. This one’s equipped with a 6-cyl. engine and automatic transmission. It has a lot of power, is fuel efficient and a pleasure to drive. I use it to tow a gooseneck trailer on which I haul our Allis Chalmers show tractor and an old gas engine.”

Best Buy

My dealer put new tires on my snowblower but I discovered that althoug

Ray Grabher, Lincoln, Neb. · Vol. 24, No. 2 (2000), p. 17

“My dealer put new tires on my snowblower but I discovered that although they were marked the same, one was taller than the other, causing the blower to run in a circle. I called the Carlisle Factory in Aiken, S.C., and they said that someone made a mistake pairing them up together.

“He volunteered to send me a new pair of better tires called Snow Hogs. I asked what they would cost, and he said, ‘You’ve had enough trouble, so these are on us – no charge.’ Five days later they came prepaid. Now my snowblower runs straight.”

Best Buy

Ford F-450 4-WD dually pickup equipped

Bruce A. Fultz, Logansport, Ind. · Vol. 24, No. 2 (2000), p. 17

Bruce likes his 1999 Ford F-450 4-WD dually pickup equipped with a 7.3-liter Power Stroke engine and automatic transmission. ‘The company I work for purchased this pickup five months ago and it works great. It starts at 10 degrees below zero without being plugged into a heater and works great in the snow. It’s the best pickup I’ve ever seen. It’s built Ford tough.”

Best Buy

New Holland 1620 HTS 4-WD tractor equipped + 1 more

John McGreevy, Jr., Fawn Grove, Pa. · Vol. 24, No. 2 (2000), p. 17

John likes his New Holland 1620 HTS 4-WD tractor equipped with a front-end loader. “It’s reasonably priced and easy to use. The loader has a lot of reach and speed.

“My all-time best buy is my 1983 Deere 2350 4-WD tractor. It has about 7,500 hours but is ready for more work. I use it to mow about 4,000 miles of highway roadsides every year. In winter I mount a blade on front and a snowblower on back.”

Best BuyWorst Buy

Miller wire welder + 1 more

Thomas E. Jackson, Jr., Bowling Green, S.C. · Vol. 24, No. 2 (2000), p. 17

“I bought my Miller wire welder two years ago and it’s my best buy. It’s a 250-amp vintage model. I’ve used it both to repair equipment and to fabricate parts. It works good at either low or high settings. Miller makes quality products.

“My worst buys are recent General Mo-tors products. I’ve owned more than 12 new or used GM vehicles during the last 35 years and they were all built with quality. However, in the last few years the company has lowered its standards. GM vehicles and parts now are sub-standard, in my opinion. Another problem is that you can’t always order them according to your needs and specifications.”

Best BuyWorst Buy

New Holland 795 manure spreader + 2 more

Steve Korver, New Oxford, Penn. · Vol. 24, No. 2 (2000), p. 17

“We like our 1995 New Holland 795 manure spreader which we bought used. It’s equipped with a tailgate and pan that works great for spreading poultry and dairy manure and also keeps it off roads. One problem was that the bolts that secure the box to the hitch broke through. It had to be reinforced.

“We use our 1989 Knight 2300 Reel Auggie to feed about 100 head of dairy animals a day. It’s easy to operate. We put some hay in it which mixed up well. It fluffs up the ration and doesn’t pack it like our old auger mixer did. Also, our old auger mixer couldn’t handle hay. It doesn’t take much horsepower to run, even when mixing hay.

“My 1990 Zetor 55 manure spreader is my worst buy. The spreader’s apron is made from log chain which has to be kept tight in order to keep it from rolling off the sprockets. The adjustment mechanism for tightening the chain is poor. The sprockets have points that fit into the chain links, and one of the points broke off. Unfortunately the sprockets are welded onto a steel shaft so I had to order an entire new shaft. It took four months to get it. One good thing is that the spinners spread poultry manure evenly.”

Best Buy

After reading in FARM SHOW about a do-it-yourself backhoe built by Joh

Warren Harris, Williamsburg, Ind. · Vol. 24, No. 2 (2000), p. 17

“After reading in FARM SHOW about a do-it-yourself backhoe built by John Mikulas, I bought a set of Cadplans from him to build one myself (Cadplans - ph 800 817-5267). I put it together without

much problem. The photo shows it in test

phase. I have since painted it yellow.

“It took me about 1 1/2 years to build although I was laid up for about four or five months after a heart attack. I’m 76 years old and building this backhoe was a fun project for me and a challenge. The rig is simple enough to operate that my daughter can handle it. I paid $100 for the plans. The company provided an instructional video tape which was quite helpful. I didn’t need any other help at all.”

Best Buy

International Harvester 800 4-row plate planter equipped + 1 more

George Steuart, Fayetteville, Tenn. · Vol. 24, No. 2 (2000), p. 17

George says his 1981 International 800 4-row plate planter equipped with Martin row cleaners is his “best buy”. “It has never failed to get a stand in any soil conditions. However, using Pioneer PDR sized seed I did have trouble getting a stand of corn. In fact in some places there was no corn at all.

“My three 30 by 90-ft. Cover All shelters have performed even better than I expected. I use them as hog barns. They’re durable, keep the hogs comfortable, and have reduced my labor requirements.”

Best Buy

New Holland 255 3-pt mounted rake tedder + 1 more

Arden Walizer, Loganton, Pa. · Vol. 24, No. 2 (2000), p. 17

“My best buy is my New Holland 255 3-pt. mounted rake tedder. It teds hay and rakes perfect. No complaints.

“My Tanco 5505 self loading bale wrapper is a best buy. It works great provided you have a tractor with adequate hydraulics. I use a 1941 Massey Harris 101 Junior tractor to operate it. The tractor didn’t have hydraulics so I installed live hydraulics off a Massey 35 self-propelled combine. It works great.”

Best Buy

Ford F-350 2-WD pickup equipped

Dave and Dale Kroft, Wabash, Ind. · Vol. 24, No. 2 (2000), p. 17

“Last May we purchased a 1999 Ford F-350 2-WD pickup equipped with a 7.2-liter diesel engine and a 9-ft. long flatbed. It has more than enough power to pull our livestock trailer. Our 1987 Ford F-250 pickup equipped with a 460 cu. in. gas engine sometimes didn’t have enough power to pull heavy loads. The new model starts good in cold weather and even though it isn’t 4-WD it handles good on snowy roads. The flatbed makes it easy to haul large items. One problem is that the ride isn’t as comfortable as we’d like. It gets about 12 mpg pulling a load compared to 5 mpg for the 1987 model.”

Best Buy

Howard Price 360Z zero turn mower

Noah N. Zimmerman, Lancaster, Pa. · Vol. 24, No. 2 (2000), p. 17

“My best buy is my 1998 Howard Price 360Z zero turn mower which we use to mow a 17-acre cemetery. I liked the mower so much I became a dealer for the company, which is headquartered at 18155 Edison Ave, Chesterfield, Mo. 63005 (ph 314 532-7000). We can mow up close to the stones so less trimming is needed later. I really like the zero turning feature. It greatly reduces our mowing time.”

Worst Buy

New Holland TV 140 tractor

Dale Neidhardt, New Salem, North Dakota · Vol. 24, No. 2 (2000), p. 17

“We’ve had tremendous problems with our bi-directional New Holland TV 140 tractor, which we bought new. When it was delivered in November, 1998, one door handle was on backwards, the mirrors were loose, the air conditioning didn’t work, and there was water in the cab that had leaked in. Later, cab windows started shattering. It even happened while the tractor was parked in the shed.

“But we’ve had much worse problems. The transmission housing cracked because a shift cylinder inside kept hitting against the inside of the housing. It was in the shop for three weeks. We had to rent another one to replace it. You don’t plan to spend money like that when you just bought a new tractor.

“Later, a hydraulic line broke while driving in the field and pumped out all the hydraulic fluid.

“One of the worst things that happened was that a pin that holds the drawbar to the tractor fell out while I was pulling my sprayer. It was a pin under the tractor that holds the entire drawbar assembly in place – not the drawbar pin. When it came off the hydraulic couplers did not release the way they are supposed to. Instead, they tore the pump off the sprayer, which cost us an extra $1,000 for a new pump – but more importantly, delayed our spraying by two days.

“Last summer another hydraulic line broke in the field. Now the differential lock doesn’t work and there’s an oil leak on the side of the engine by the injection pump.

“New Holland says it’s not responsible for extra expenses caused by the failure of its tractor. But I say, who would ever expect the transmission cover to break or the drawbar to fall off a new tractor? We’re frustrated from dealing with the company because they do not seem to want to recognize that this tractor has big problems.”