Real farmers rate what they bought, from FARM SHOW MagazineSubscribe  ·  Free issue  ·  Send us your Best or Worst Buy
Subscribe to FARM SHOW
Home › Brands › Harbor Freight

Harbor Freight: what farmers say

118 reports in FARM SHOW · 87 Best Buys32 Worst Buys

Harbor Freight (general)

31 Best Buys10 Worst Buys
Best Buy
Will F. · Vol. 50, No. 5 (2026), p. 14

“I do a good bit of welding. That requires grinding, and over the years I’ve used…”

This listing is from the current issue of FARM SHOW. Subscribe to read it all or get a free issue.
Best Buy
Larry Donkers, Elysian, Minn. · Vol. 50, No. 4 (2026), p. 14

“I really like my Hercules drill set from Harbor Freight. We used it to build a deck right out of the box. It’s full of torque, and the 5Ah battery lasts well.”

Best Buy
Tom Schauer, Lawrence, Mich. · Vol. 47, No. 6 (2023), p. 15

“My gas-powered post hole auger from Harbor Freight worked like a charm. It did all I needed and more. For light work, it’s a good buy.”

Best Buy
Billy Tucker, Alamogordo, New Mexico · Vol. 46, No. 2 (2022), p. 15

“My towable trencher from Harbor Freight works flawlessly in tight spaces. There is a Facebook group that’s very helpful should repairs be needed or modifications made.”

Worst Buy
Neal Baker, Knoxville, Penn. · Vol. 45, No. 1 (2021), p. 12

He’s disappointed with his Pittsburgh model 99736 tubing roller from Harbor Freight. “After only 4 bends, the threads on the set screws on the drive wheel stripped out. I drilled a hole through and put a bolt in. This didn’t work great but I could still use it. I rolled 4 more pieces when the threads on the top block stripped out. This made the roller useless. The entire roller is too light to be on the market. Harbor Freight told me there are no replacement parts available and that I would have to source needed parts locally.”

Best Buy
Stephen Zonies, Waitsfield, Vt. · Vol. 44, No. 4 (2020), p. 13

“Digging 2 dozen post holes with a conventional post hole digger took me more than 3 hrs. of blood, sweat and tears and when I was done my back and arms said ‘Don’t do that’. So I bought a Predator gas-powered earth auger from Harbor Freight. It worked great. I dug the same amount of holes in just about 20 min. The only thing to watch out for is rocks. They will definitely ‘shake, rattle and roll’ you.”

Best Buy
Richard J. Cellino, Erie, Penn. · Vol. 44, No. 1 (2020), p. 13

“The 60-in. finished hardwood workbench I bought last year at Harbor Freight is my best buy. I paid $119.99 for it with a coupon. It’s 60 in. long, 20 in. deep, and 34 in. high with an end vise, twelve 3/4-in. dia. dog holes, four drawers, and a lower shelf. The workbench came as a kit and took me 2 to 3 hrs. to assemble. I’m 82 years old so this workbench was quite heavy to handle by myself. But I was so pleased with it that I went back and bought two more for the shop in my barn.

“Over the last 60 years I’ve made several workbenches out of framing lumber. The lumber alone for them cost twice as much as my Harbor Freight workbench, and my benches don’t look as nice.”

Best Buy
H.B. Clemmons, Dexter, N. Mex. · Vol. 43, No. 1 (2019), p. 15

He’s impressed with hand tools sold by Harbor Freight. “I work in a commercial irrigation pump shop where I supply my own tools. I use Pittsburgh tools almost exclusively, and they’ve never failed me. The quality of these tools has really improved. Harbor Freight consumables such as cutting wheels, etc., cost far less than ones sold by welding shops.”

Best Buy
Nicholas Stanchak, Newburgh, N.Y. · Vol. 42, No. 6 (2018), p. 15

“I think Harbor Freight products are just as good or better than the big box store branded products being offered these days. The company catalog uses a 5-star customer rating system for any particular tool, and in my experience it has been spot-on accurate.”

Best Buy
Terry McClain, Carson, Iowa · Vol. 41, No. 3 (2017), p. 12

“I’m happy with the 12-volt battery maintainers I bought at Harbor Freight. I paid about $7 apiece for them. The batteries on my antique tractors used to lose their charge when not in use, but these inexpensive maintainers keep them ready to start.”

Best Buy
Fred Fowler, Afton, N.Y. · Vol. 41, No. 3 (2017), p. 15

“I like the combination cordless drill and light set I bought 3 years ago at Harbor Freight. After using dozens of different cordless drills with batteries that didn’t last, I had about given up. Then I bought this set for $19.95, mainly for the light. However, I discovered the drill works good and the battery holds up. Best of all, a replacement battery costs only $12.95.”

Best Buy
Donald Halstead, Newfane, N.Y. · Vol. 41, No. 2 (2017), p. 13

Donald has been a Deere mechanic for more than 55 years and says he likes the 2 extendable ratchet wrenches he bought at Harbor Freight. “I bought a 1/4 by 3/8 wrench for $14.99 and a 1/2-in. model for $17.99. No problems. I use them every day at work and also on my farm. These wrenches come with a lifetime warranty. The ratchets have very fine teeth so I can use them in tights pots even with the handle fully extended.”

Best Buy
Delbert Hayes, Norwalk, Iowa · Vol. 41, No. 2 (2017), p. 14

“We really like the 20-ton air hydraulic bottle jack we bought last year from Harbor Freight. It comes with a 4-ft. long air hose. We use a Harbor Freight 9-gal., 135 psi gas-powered air compressor to operate it. We’ve used this jack many times to fix flat tires on our combine, including one time when it was loaded with corn. We use the compressor to blow debris off the combine as we move from field to field.”

Best Buy
John Gass, Franklin, Ill. · Vol. 39, No. 4 (2015), p. 13

“Last year I bought an electric chainsaw sharpener from Harbor Freight for $30. Works great.”

Best Buy
Mark Conyers, Weatherford, Texas · Vol. 39, No. 4 (2015), p. 14

“I like the Luminar rechargeable lights I bought last year at Harbor Freight. I own an underhood light, a spotlight, and a couple of work lights. I keep one work light in my shop and the other in my truck. All of them have performed beyond my expectations. They hold their charge and can be recharged in a reasonable amount of time.”

Best Buy
Jackie Leeper, Carterville, Ill. · Vol. 39, No. 1 (2015), p. 14

“The riding mower lift I bought from Harbor Freight works well on all standard size mowers. I bought it on sale for 20 percent off so it was just $79. It’s hydraulic-operated which makes it easy to use.”

Best Buy
Philip Seidenschwarz, Bybee, Tenn. · Vol. 38, No. 6 (2014), p. 14

Philip’s the satisfied owner of a 2011 10 by 12-ft. aluminum greenhouse built by One Stop Gardens in China and sold by Harbor Freight. The building comes with 4 roof vents. “Everything is included in the package, with directions that are easy to follow. It’s designed with an extruded aluminum frame that’s easy to assemble, and with woven plastic panels that fit snug into channels with locking clips.

“Last spring we used this greenhouse to grow more than 3,000 vegetable and herb plants on home-built, plastic pipe shelving. This building is all it’s advertised to be, and more. We’re 100 percent pleased with it.”

Best Buy
Ron Reeves, Port Charlotte, Fla. · Vol. 38, No. 3 (2014), p. 14

“I’ve wanted a good woodworker’s bench for a long time, but couldn’t justify spending $500 to $900 for one. Harbor Freight has a 60-in. hardwood bench equipped with 4 drawers and a bench vise on one end that sold for $139. I thought I’d give it a try and it’s great. I did add a brace under the bottom shelf and installed another vise at the other end of the bench.

“This is a pretty heavy bench, so in order to move it around my shop I made a pair of ‘roller skates’ for the bench’s feet by making a box that fits each foot and mounting 2 locking caster wheels on each box. The boxes slip over the feet and are held on by one bolt. I can roll the unit anywhere. I now have a sturdy bench for less than half the cost of the ones advertised in woodworking catalogs.”

Best Buy
David Nemeth, Campbell Hall, N.Y. · Vol. 38, No. 2 (2014), p. 12

“My friend needed a new engine for his log splitter, which had been in a flood. We went to Harbor Freight and bought a Predator engine. It ran for only about 3 hrs. before the ignition quit. The company replaced it, but that one ran for only a few hours before it seized up. The company promptly gave my friend his money back.”

Best Buy
David Davignon, Damar, Kan. · Vol. 38, No. 1 (2014), p. 14

“The 2007 Drill Master 3/8-in., 18-volt cordless drill I bought at Harbor Freight has performed flawlessly, even after I accidentally dropped it from a house roof while installing metal roofing. The drill fell 3 times in one day. Each time the battery fell out and the drill lost some plastic, but it still works.”

Best Buy
Lynn A. Peters, Clinton, N.Y. · Vol. 37, No. 3 (2013), p. 13

“The 1 1/2 and 3-ton Pittsburg aluminum jacks I bought at Harbor Freight are lightweight and lift fast. They’re also easy to handle and low-priced. I also bought a small 800-watt portable generator at Harbor Freight that’s lightweight and runs almost 6 hrs. on a gallon of gas. It comes in handy for operating small electrical tools and lights.”

Best Buy
Delbert Hayes, Norwalk, Iowa · Vol. 37, No. 2 (2013), p. 14

“From Harbor Freight I bought a low cost, heated razor blade decal remover and used it to remove two ‘slow moving vehicle’ decals on a grain cart. It took only a short time to do and left the cart’s surface smooth.”

Worst Buy
Bud N. Vogelzang, Sioux Center, Iowa · Vol. 36, No. 1 (2012), p. 14

“The chainsaw chain sharpener I bought from Harbor Freight is my worst buy. After I used it to sharpen about six chains, the glue holding the magnets around the armature let loose and the motor burned up.”

Worst Buy
Gunhild Vetter, Bosque Farms, New Mexico · Vol. 35, No. 5 (2011), p. 14

Gunhild nominates the 10 by 12-ft. greenhouse he bought from Harbor Freight as his “worst buy”. “This building was impossible to put together with the instructions provided. I had to get revised instructions and, after many months of fussing with it, I ¿ nally got it completed. However, when the spring winds came the panels started popping out and, on one extremely windy day, I watched as the wind lifted and twisted the entire building, leaving me with a twisted aluminum frame and scattered panels. Fortunately, the straps holding it did their job and kept the building from À ying away.”

Best Buy
Roy Huntington, Joplin, Mo. · Vol. 35, No. 2 (2011), p. 14

“The 1,200-lb. capacity, hydraulic-operated motorcycle lift I bought from Harbor Freight a few years ago is a best buy. It operates by stepping on a foot pump. I use this lift to maintain our big motorcycles, but it also works great for working on small machines like riding mowers, ATV’s, mower decks, and more. It’s nice to get something up to waist height, and I keep a rolling stool so I can move around while I work. I paid only about $300 for it.”

Best Buy
Duane Johnson, Tucson, Ariz. · Vol. 34, No. 4 (2010), p. 13

“In recent years I’ve purchased several hand tools from Harbor Freight that have performed well, and for the price they can’t be beat. The tools include an angle grinder, random orbital sander, and heat gun. All of them worked great.”

Best Buy
Lloyd Painter, Lima, Ohio · Vol. 34, No. 3 (2010), p. 13

“It works well and has been trouble-free,” says Lloyd about the 10-in. sliding compound miter saw he bought from Harbor Freight. “I paid $100 for it. I almost bought a $500 saw, but I’m glad I bought this one instead.”

Worst Buy
R.A. Mansfield, Bath, Maine · Vol. 34, No. 1 (2010), p. 14

“I’m disappointed with the $39.99 chain sharpener I bought at Harbor Freight. The motor arbor shifted after I had sharpened only five or six chains, allowing the end of the shaft to wear through the guard. It wore the shaft down so much that the nut will no longer hold the grinding wheel.”

Best Buy
Donald Ober, Manheim, Penn. · Vol. 33, No. 5 (2009), p. 13

“The self-darkening welding helmet I bought from Harbor Freight for less than $50 is my best buy. One tip – don’t hang a trouble light too close to where you want to weld. The helmet will think you’re striking an arc and will go dark.”

Best Buy
Jim Rymut, North Royalton, Ohio · Vol. 33, No. 4 (2009), p. 14

Jim likes the 2007 electric chainsaw sharpener he bought from Harbor Freight. “I already had a much better chainsaw sharpener that I bought 20 years ago for hundreds of dollars. However, I would have to sharpen a mountain of chains in order to justify buying one of those machines again. This sharpener is lightweight and easy to use, and I paid only $29 for it. It paid for itself after sharpening only a few chains.

“I’m not happy with the 2,000-lb. Chicago electric utility winch I bought from Harbor Freight. I needed help getting my riding mower up the ramps to my pickup. I mounted the winch in the pickup bed and mounted the remote control at the rear bumper, so I could watch as the mower was pulled up. However, the winch couldn’t pull it up even though it’s rated at 2,000 lbs. So I’m still pushing the mower up the ramps by hand.”

Worst Buy
Sean Crook, Arena, Wis. · Vol. 33, No. 2 (2009), p. 14

He had trouble with an exhaust pipe expander he bought from Harbor Freight. “We tried it on thin wall exhaust pipe, but unfortunately the threads stripped before we even applied much torque. The same problem happened with two more replacement units.”

Best Buy
James Rodlund, Stillwater, Minn. · Vol. 33, No. 1 (2009), p. 13

“My best buy is a wood floor nailer and stapler that I bought at Harbor Freight. I had to lay about 700 sq. ft. of hickory wood flooring in my hallway, kitchen, and family room. This tool worked beyond my expectations, and it cost only about one third as much as other floor nailers that I looked at.”

Worst Buy
Doug Kramer, Elroy, Wis. · Vol. 30, No. 5 (2006), p. 14

“My worst buys are the battery-powered 18-volt drill, 18-volt saw, and 18-volt grease gun that I bought from Harbor Freight. All were underpowered compared to other 18-volt tools I own, and the battery life is only minutes. I wasted my money on these tools. I keep them in my shop because their distinctive orange color reminds me never to buy one again.”

Best Buy
Steve Nelson, Winston-Salem, N.C. · Vol. 28, No. 6 (2004), p. 14

Steve likes his Harbor Freight 1-in. SDS rotary hammer drill. “I was installing an automatic lift on my garage door and burned out a 1/2-in. hammer drill. Then I bought the Harbor Freight drill. It does an awesome job, and I was able to buy it on sale for only $65. I recommend buying a model that both rotates and hammers.”

Best BuyWorst Buy
David Arnold, Meeker, Colo. · Vol. 28, No. 5 (2004), p. 13

A 1/2-in. drill from Harbor Freight rates as David’s “best buy.” “I’ve tried my best to break the darn thing but I can’t. I’ve used it to build my log house and countless other projects.

“A creeper that I bought from Harbor Freight is my worst buy. The wheels broke off after only about a week of use.”

Best Buy
John Monsees, San Jose, Calif. · Vol. 28, No. 1 (2004), p. 14

“My best buy is a small metal cutting bandsaw that I Harbor Freight bought from (www.HarborFreightTools.com). I found the blade adjustment feature to be very crude so I changed the design of the adjuster, which made it much easier to set the blade to cut straight. I also added an outer 4-in. table to the original narrow one. It lets me clamp stock to the table instead of having to use the built-in vise and allows me to cut short stock at any angle. It sure beats using a hack saw.”

Worst Buy
Ken Scharabok, Waverly, Tenn. · Vol. 27, No. 6 (2003), p. 12

“I bought a ‘Nick the Grinder’ chain saw sharpener from Harbor Freight (www.harbor freighttools.com). Most commercial shops take so much off the teeth that after three sharpenings the chain saw chains are almost useless. While it may look like a toy, this is a serious piece of equipment. It’s very simple to set up and takes off only what’s required to get the chain sharp, meaning I can get several times the number of uses out of a chain versus professional sharpening. It sells on the website for $79.99. I estimate the machine will pay for itself in one season of firewood cutting.”

Worst Buy
David Shelton, Mt. Sherman, Ky. · Vol. 27, No. 1 (2003), p. 13

David says the 16-in. wood planer he bought last year from Harbor Freight is his “worst buy”. “The bearing on the blade shaft got so hot the first time it was used that the shaft broke. The company replaced the planer, but we had the same problem with the new one. You can only use it for a short time before it gets hot. Another problem is that the feeder roller makes marks on the boards as they go through the tool.”

Worst Buy
Raymond Swenson, Brooks, Minn. · Vol. 14, No. 1 (1990), p. 13

Raymond Swenson, Brooks, Minn.: “My best buy of all time is a 1981 Volkswagen Rabbit diesel car. It has 260,000 miles and is still doing great.” “Another best buy is my 1984 Gleaner N7 combine, It has tremendous capacity, a quict cab, and is nice to operate.” On the negative side, “Shop tools from Harbor Freight and Salyage are inconsistent in quality. Some tools seem okay, but others break easily.”

Best Buy
Douglas Long, Albion, N.Y. · Vol. 7, No. 4 (1983), p. 12

Douglas Long, Albion, N.Y.: “The drill press is small enough and light enough to be taken anywhere the work is, yet it has adequate power to drill through the toughest of materials. It’s been a real time saver around the farm since we purchased it,’ says Douglas, pleased with his 3-speed bench model drill press purchased from Harbor Freight and Salvage, Hollywood, Calif.

Harbor Freight tools

5 Best Buys2 Worst Buys
Worst Buy
Bill Priddy, Stephenville, Texas · Vol. 49, No. 6 (2025), p. 14

“Any tool that I ever bought from Harbor Freight turned out to be a piece of crap. I finally learned my lesson about products made in China.”

Best Buy
Dan Eagleton, Decatur, Neb. · Vol. 43, No. 6 (2019), p. 15

“I’ve been buying Harbor Freight tools for at least 40 years, and have noticed they now provide a better choice of power tools and shop equipment than in the past. The hand tools are also of better quality, and new stores are popping up everywhere. Harbor Freight tools have saved me a lot of money over the years. Check out their new tool cabinets on wheels - they’re as good as you’ll find anywhere.”

Best Buy
Richard McDonald, Maple Valley, Wash. · Vol. 39, No. 2 (2015), p. 14

“I use my Harbor Freight cordless oscillating tool to trim the bottom branches at my Christmas tree farm. It’s lightweight and the battery lasts a surprisingly long time. I also used this tool while rebuilding a rotted-out motorhome. I bought a second model so I can alternate batteries.”

Best Buy
Larry C. Miller, Harper, Kansas · Vol. 32, No. 3 (2008), p. 14

“After reading a number of FARM SHOW reports about Harbor Freight electric tools, here’s my experience regarding a 1/2 hp drill that I bought used on eBay. I didn’t know it was a Harbor Freight product until I received it. I was rather new at shopping on eBay at the time so I can blame my inexperience. However, it didn’t turn out all that bad.

“When I received the drill it did run for a short time but then it quit working. Rather than complain to the seller, I decided to check out the switch. I discovered a ground wire had come out of the wire terminal block that connected the ground circuit. That fix solved the running problem, but then once it would run for several minutes it would begin to smell hot so this time I checked the brushes. I found that one of the brushes hadn’t been inserted into the holder correctly, and because the brush didn’t contact the armature properly it caused a heating problem. Once I fixed that I haven’t had any more problems.”

Best Buy
George Schneider, Pioneer, Calif. · Vol. 32, No. 2 (2008), p. 14

“I often read negative comments about Harbor Freight tools in FARM SHOW. However, I have a different philosophy. I use Harbor Freight to buy tools that I don’t necessarily need on a long term basis. For example, instead of renting a 1/2-in. drill for two days at a cost of $10 a day, I’ll buy a cheap drill for $29 and toss it after I’m done with the job. That way I don’t worry about spending all my time renting and returning a rental. I don’t expect to find ‘professional’ tools at Harbor Freight in the first place.”

Best Buy
Ken Scharabok, Waverly, Tenn. · Vol. 27, No. 4 (2003), p. 15

“In our area, when you go to a small engine repair shop to have a chain saw’s teeth sharpened, they take off so much of the teeth that after three sharpenings the chains are about useless. So I bought a ‘Nick the Grinder’ over eBay (www.eBay.com), which turned out to be a Harbor Freight tool (www.harbor freighttools.com). It’s my best buy. While it may look like a toy, it’s a serious piece of equipment that’s simple to set up and use. I can take off as little of the teeth as required, meaning I can get several times the number of uses out of a chain compared to ‘professional’ sharpening. I estimate this machine will pay for itself in only one season of woodlot management and firewood cutting.”

Worst Buy
Joseph deNatale, Pittsfield, Maine · Vol. 26, No. 2 (2002), p. 17

Joseph says Harbor Freight tools are his “worst buy”. “I’ve purchased several of the company’s tools for use in my apple orchard. Even though their tools are priced cheap they’re usually okay for occasional use. However, when some of the tools became defective I soon discovered the company’s customer service leaves a lot to be desired.

“I bought a titanium-plated drill bit set and a cold chisel set. Several of the drill bits were so soft I could bend them by hand, and when I used some of the chisels they shattered. I sent the tools back to the company and asked for replacements. I also told them about some significantly dangerous manufacturing defects that I had noticed in the tools so they could correct them for future buyers. The company never replied, so I wrote them a letter asking about the status of the returned items. They sent back a form letter that told me to call their customer service department. I called them and was told that all customer service representatives were busy. I waited more than 40 minutes before I became to springtime – you need to recalibrate the impatient and finally hung up. I sent three more letters to them but never got a written response. I was always referred by form letter to their customer service department.

“After writing four letters and spending a total of more than 2 1/2 hours on the phone waiting to talk to someone, I finally got through. The person I talked to said they couldn’t find the tools I had returned. The entire experience was an exercise in frustration.”

Worst Buy
Bruce E. Smith, Covington, Ohio · Vol. 45, No. 3 (2021), p. 13

“My 1968 Deere 4020 diesel tractor, which I use with a 5-bottom semi-mounted plow, is worth more now than what I paid for it new.”

On the negative side, “Harbor Freight 4 1/2-in. angle grinders bend easily. There’s no bearing for the upper end of the wheel shaft, which causes the shaft to wear out prematurely.

“I was only able to use my Harbor Freight high lift jack once before the handle on it bent where it’s welded to the frame, making the jack unusable. Rural King makes a better and stronger jack (ph 800 561-1752; www.ruralking.com).

Best Buy
Ronald R. Shippey, Canon City, Colo. · Vol. 43, No. 2 (2019), p. 13

“The 4 1/2-in. cut-off wheels I use on my Harbor Freight 4 1/2-in. grinder can cut through 1/2-in. thick steel and are less expensive to operate than a cutting torch. I also like the company’s step drill set, which can be used to enlarge holes in 1/2-in. thick steel.

“In 2017 I bought a used Chevrolet Silverado 2500 HD pickup with 3,950 miles on it. I put on another 4,450 miles but got only 9.2 mpg, so last November I sold it. This pickup had other problems. I couldn’t use the radio because of the confusing data display. An alarm kept coming on as I was driving indicating that I was exceeding the speed limit, even though I was going 10 mph below the posted limit.”

Worst Buy
Billie Leonard, Rathdrum, Idaho · Vol. 41, No. 2 (2017), p. 13

“My 2016 DeWalt 20-volt drill stays charged longer than any drill I’ve ever owned.

“My 2016 Harbor Freight 4 1/2-in. grinder is a worst buy. The first time I tried to use it smoke rolled out of it, and it has never worked since.”

Worst Buy
John Kostura, Kettle Falls, Wash. · Vol. 34, No. 3 (2010), p. 14

A 2007 Jinma 284 tractor equipped with a front-end loader and backhoe rates as John’s “best buy”. “This tractor has about 450 hours on it with no problems. I’ve used it for logging and landscaping work and even built a plow for it that mounts on the bucket. There was a problem with a leaking hose which the company replaced. The company has been helpful with questions I had regarding maintenance.

“My Harbor Freight 4 1/2-in. side grinder is my worst buy. The problem is with a wire that connects to the brushes. I reworked the connectors, which solved the problem.”

Best Buy
H.L. Bagg II, Eva, Tenn. · Vol. 31, No. 5 (2007), p. 14

“I like my 2004 Harbor Freight 4 1/2-in. angle grinder. It has worn out about 100 cutting and grinding discs but is still going great. I owned one before this one and it only lasted a week. But this one is great.”

Best Buy
David Ziegler, Manchester, Mo. · Vol. 40, No. 4 (2016), p. 13

David’s happy with his 2014 Harbor Freight 10-ton, hand-pumped log splitter. “We don’t heat our home with wood, but we do like to see a nice fire going in our fireplace. This log splitter makes splitting wood a lot easier. I wish we had bought it years ago.”

Best Buy
David Ziegler, Ballwin, Mo. · Vol. 37, No. 5 (2013), p. 12

David’s happy with his Harbor Freight 10-ton hand-operated log splitter. “I use it to split wood measuring 14 in. dia. or less. I’m getting older and wish I had bought this splitter years ago. I really like it.

“My worst buy was a 4 by 6-in. manual jaw pullers that I bought from W.W. Grainger. These jaw pullers wouldn’t hold pulleys, wheels or gears firmly. When I turned the center thread the jaws would slip off the edge of the pulleys or gears. The problem was the bottom of the jaws wasn’t deep enough to hold.”

Harbor Freight 1/2-in drive

1 Best Buy1 Worst Buy
Best Buy
Robert Thomas II, Oak Grove, Mo. · Vol. 37, No. 3 (2013), p. 14

“I like my Harbor Freight 1/2-in. drive Earthquake impact wrench. The quality and torque is equal to impact wrenches that cost twice as much. I paid $71.20 for it with a 20 percent off coupon. I’ve used this impact wrench to change tires on trailers and tractors, and it easily loosens the most stubborn bolts.

“I bought my NumMax 21 degree framing nailer at Home Depot to finish my basement. It’s lightweight and works well, and it was priced at only $89.99. I had to order this tool online but it came with free shipping. Excellent quality and no jams. It’s built rugged and shoots a variety of different nails so I can meet all building codes.”

Worst Buy
Paul Grisso, Roanoke, Va. · Vol. 29, No. 5 (2005), p. 15

“My Mantis rototiller equipped with a Honda engine is handy to use. On rocky ground I pull it backward to keep from jamming rocks in the tines. It works great in small areas.

“My Harbor Freight 1/2-in., 18-volt cordless drill is my worst buy. The problem is the chuck won’t stay in the body of the drill. This tool was cheap so I guess you get what you pay for.”

Best Buy
Ron Enfield, Atwood, Kan. · Vol. 50, No. 2 (2026), p. 13

“My 2025 Harbor Freight Bauer mini chainsaw and hedge trimmer have worked great without failure, and the battery life is very good.”

Worst Buy
Dan Ashburn, Bloomfield, N.M. · Vol. 49, No. 6 (2025), p. 15

On the positive side is Dan’s 2023 5-wheel Enorossi hay rake (www.enorossi.it/en; ph 252-442-0700). “This hay rake is so simple, there’s almost nothing to go wrong with it. It’s also very easy on the hay and doesn’t knock leaves off of alfalfa like a powered rake will. It was also very affordable.”

On the negative side is a Harbor Freight Bauer hammer drill purchased new. “The drill got stuck in hammer mode. I took it back to Harbor Freight, and it was one day out of warranty. But Harbor Freight replaced it, I just had to buy the $20 extended warranty, so I guess it worked out okay after all.”

Harbor Freight Predator engines

1 Best Buy1 Worst Buy
Worst Buy
Joe M. Yoder, J.M. Sales and Service, Wilton, Wis. · Vol. 43, No. 2 (2019), p. 14

“I’m a small engine mechanic, and the most troublesome engines that come to my shop for repairs are Harbor Freight Predator engines. By the time they need to be repaired, components such as the gas tank and air cleaner are either cracked or broken and replacing them gets expensive. These engines perform well and are relatively cheap to buy. But financially, you’re better off not taking them in for repair work. Just buy a new engine and keep the old one for parts.”

Best Buy
Paul W. Gates, Jr., Barney, Ga · Vol. 43, No. 1 (2019), p. 15

“When the engine on my TroyBilt walk-behind rototiller finally wore out, I replaced it with a 6 1/2 hp. Harbor Freight Predator engine that cost only $99. It always starts right up after just one or two pulls and works great. I also replaced the hard-to-start engine on my TroyBilt pressure washer with a Predator. I had to drill a couple of mounting holes for it, but now the pressure washer is easy to start even after sitting idle for months at a time. I only use non-ethanol gas in both engines.”

Harbor Freight 1 750 psi

1 Best Buy0 Worst Buys
Best Buy
Daniel Alderfer, Carbondale, Colo. · Vol. 44, No. 3 (2020), p. 15

“My Harbor Freight 1,750 psi corded electric pressure washer is built tough, well-designed, and has a lot of power. It rides on smooth rolling 4-in. dia. wheels and comes with a 20-ft. high pressure hose, an adjustable spray nozzle, and a 35-ft. power cord that stores on-board. I bought it on sale for $80.”

Harbor Freight 10

1 Best Buy0 Worst Buys
Best Buy
Dave Mertell, Independence, Mo. · Vol. 43, No. 4 (2019), p. 15

“I received a Harbor Freight 10 by 12-ft. greenhouse as a gift from my son and his family for my 93rd birthday. It came with good instructions and was fun to set up with my son. It’s a real pleasure to have fresh vegetables as early as the beginning of April.

“My Troy-Bilt rototiller is hard to start and doesn’t work as well as I expected. However, this was also a gift so I continue to use it.”

Harbor Freight 12-ton press

1 Best Buy0 Worst Buys
Best Buy
Steven Higgins, Indiana, Penn. · Vol. 40, No. 5 (2016), p. 13

Steven likes his Harbor Freight 12-ton press. “It used to take a long time to replace the bearings on the blades on my 40-year-old WheelHorse riding mower, but with this press it takes only a few minutes.”

Harbor Freight 1/4-in drill bits

1 Best Buy0 Worst Buys
Best Buy
Richard Keeney, Truxton, N.Y. · Vol. 50, No. 1 (2026), p. 14

“I’ve been pleased with my Kubota F2880 front mower. It’s a tough machine for mowing the lawn and along the electric fence line. The 4-WD rear steer turns short. I like that it has a steering wheel instead of lever steering, and I appreciate the power steering.

“My rechargeable EGO 650 cfm leaf blower is great for clearing off my baler and batwing mower. It’s powerful and has a long-lasting battery.

“FARM SHOW has good jokes that make me laugh.

“Harbor Freight 1/4-in. drill bits are only good for one or two uses.”

Harbor Freight 15.8-hp motor

0 Best Buys1 Worst Buy
Worst Buy
Fred J. Hall, Monmouth, Ill. · Vol. 50, No. 1 (2026), p. 14

“My Forney 275 AC-DC welder is a best buy. After about 30 years, it still works great.

“My Ingersol 2-stage air compressor with an 80-gal. tank has been so trouble-free that I purchased a second one.

“I’m disappointed with the Pocket Hose Copper Bullet garden hose. It’s about 45 ft. from the hydrant in my wife’s horse barn to the last bucket. I bought the 75-ft. hose for reserve length. By 45 ft., the flow is reduced by about 50%. I can water the horses faster with a bucket from the hydrant.

“I replaced the Kohler motor in our Load King lowboy with a Harbor Freight 15.8-hp motor. It required a lot of time and machine work for mounting. It made one trip before filling the crank case with gas and locking it up. They replaced the motor, but our downtime wasn’t good.”

Harbor Freight 20-ton air hydraulic bottle

1 Best Buy0 Worst Buys
Best Buy
Delbert Hayes, Norwalk, Iowa · Vol. 42, No. 2 (2018), p. 15

“My Harbor Freight 20-ton air hydraulic bottle jack works great for jacking up trucks and combines. I also own a 1 1/2-ton aluminum rapid pump jack that works good. It weighs just 34 lbs.”

Harbor Freight 230-volt 36-amp plasma

0 Best Buys1 Worst Buy
Worst Buy
Dennis Rood, Clarksville, Ark. · Vol. 30, No. 5 (2006), p. 15

Dennis likes the 1 1/8 hp, 880-lb. double cable capacity electric hoist that he bought from Har-bor Freight. “I attached the hoist to a trolley assembly on an 18-ft. by 6-in. overhead steel I-beam in my shop. I’ve used the hoist to pull auto engines, to lift one end of an ATV when replacing axle bearings, to lift a riding mower when replacing blades, and to load and unload heavy items from my pickup. It makes handling material and equipment a much easier and safer job.

“My 2005 Harbor Freight 230-volt, 36-amp plasma cutter is my worst buy. I bought it with a 1-year extended warranty at extra cost. From the start, it wouldn’t cut for more than several seconds at a time. Yet air would continue to blow for minutes, and the power switch wouldn’t turn it off. After making six phone calls and spending a half day on hold, I was finally provided with a replacement unit. At first it did everything it was supposed to do. But after I used it several times, the power switch went out and then it would no longer cut. I now have lost my desire for a plasma cutter.”

Harbor Freight 2-ton engine hoist

1 Best Buy0 Worst Buys
Best Buy
David Mertell, Independence, Mo. · Vol. 41, No. 1 (2017), p. 13

David’s satisfied with his 2013 Harbor Freight 2-ton engine hoist and 2015 Harbor Freight 20-ton shop press. “I’m a 90-year-old do-it-yourselfer. In 2013 I built a 6 by 16-ft. fifth wheel utility trailer from the ground up, and in 2015 a friend gave me an Allis Chalmers B tractor which I restored to like-new condition. I used the engine hoist and shop press during the restoration project, and both performed perfectly.”

Harbor Freight 301-piece mechanics tool kit

1 Best Buy0 Worst Buys
Best Buy
Matthew W. Stewart, Huachuca City, Ariz. · Vol. 47, No. 2 (2023), p. 14

“My Harbor Freight 301-piece mechanics tool kit is the perfect kit to fit in my truck’s cross bed toolbox. I attend many tractor and engine shows and needed a comprehensive tool kit to fix any mechanical problem that might crop up.

“We bought our built-in GE combination oven/microwave (Model JT3800SH7SS) to replace our old unit that failed after 16 years. Six months after the 1-year warranty expired, the microwave failed. The service tech knew the part numbers by heart. The internal parts were all labeled ‘Made in China.’ GE charges full retail for inferior, foreign-made appliances.”

Harbor Freight 45-watt solar panel kit

1 Best Buy0 Worst Buys
Best Buy
James Olson, Butte, N. Dak. · Vol. 38, No. 3 (2014), p. 12

“My Harbor Freight 45-watt solar panel kit is well-built and reasonably priced. It comes with a charge controller, lights and all the necessary wiring.”

Harbor Freight 5-drawer tool cart

1 Best Buy0 Worst Buys
Best Buy
Paul Peyton, Ava, Mo. · Vol. 41, No. 1 (2017), p. 15

“My Harbor Freight 5-drawer tool cart has a rated capacity of 750 lbs. Fully loaded, the large caster wheels make the cart easy to move around, even on a rough or cracked floor. This tool cart was a bargain at $169, which is only about a third the cost of other, lesser-quality products.

“Two years ago we installed eight 12-volt Trojan batteries in our solar power system and they’ve been trouble-free (www.trojanbattery.com; ph 800 423-6569). Other batteries we’ve tried have failed in as little as 6 mo.

“We built our house using a Makita 10-in. power miter saw. It cuts square every time, even after being reset to cut angles. The angles are perfect and repeatable. It’s equipped with a Freud blade, so every cut is perfectly smooth with no splintering. I highly recommend both the Makita saw and the Freud blade (www.freudtools.com; ph 800 334-4107).

“My 1994 Husqvarna 66 chainsaw has performed flawlessly with no repairs and still has the original spark plug. When the fuel hose collapsed a couple of years ago, I discovered the only available replacement hose was too short. (It’s a special molded hose with one end larger than the other and an integral grommet to seal where it goes into the tank). The dealer and company rep argued that the new, shorter fuel hose was correct, but the hose can’t reach the fuel once the tank goes below half-full. The arrogance and unhelpful attitude of this company was disappointing.”

Harbor Freight 9-amp surface conditioning tool

1 Best Buy0 Worst Buys
Best Buy
Joey May, Florence, Ala. · Vol. 49, No. 4 (2025), p. 15

“I’ve owned an Exmark Lazer Z HP for over 16 years. Due to its reliability, I purchased a new Exmark Radius 60. It has a great cut, a comfortable ride, and good fuel economy. I had a warranty issue arise, and the company had my local dealer promptly fix the issue under warranty. They’re very reliable machines. Worth every penny of the purchase price.

“I’ve been pleased with my Harbor Freight 9-amp surface conditioning tool for metal. It does a great job cleaning rust off metal surfaces and is reasonably priced. The replacement wheels are also reasonable.”

Harbor Freight Bauer 20V angle grinder

0 Best Buys1 Worst Buy
Worst Buy
Thurman Vangen, Ferryville, Wis. · Vol. 50, No. 2 (2026), p. 15

Thurman’s had good luck with his Milwaukee M18 cordless drill (model 2804-20). “I replaced some deck boards on my patio and drove 498 3 1/2-in. screws with one battery charge. I have 11 other M18 tools (impacts, saws, inflators and grinders). They’re a bit more expensive and heavier, but they always work, which is why I keep buying them.

“Unfortunately, I made the mistake of buying a Harbor Freight Bauer 20V angle grinder. It’s a brushless model with electronic controls. If I apply any pressure, it stops running. I have to release the trigger, count to two, and it starts again. It does this consistently. I do repair work, so it’s basically unusable.”

Harbor Freight Bauer 20-volt 4 1/2-in angle grinder

1 Best Buy0 Worst Buys
Best Buy
Delbert Hays, Norwalk, Iowa · Vol. 46, No. 4 (2022), p. 12

“I’ve had my Harbor Freight Bauer 20-volt 4 1/2-in. angle grinder for about two years. It’s so handy to sharpen a dull section or cut a hose clamp off. There are so many uses for it.”

Harbor Freight Chicago electric dual

0 Best Buys1 Worst Buy
Worst Buy
Paul E. Maurice, Auburn, Mass. · Vol. 31, No. 2 (2007), p. 15

“My worst buy was my Harbor Freight Chicago electric dual Mig 151 welder. While the price was attractive, the machine wasn’t. It’s made mostly of model airplane plastic and conked out after consuming less than one spool of wire. The flimsy wire feeder isn’t user serviceable, nor is the hard-wired gun.

“The only thing worse than the welder itself, was the dismal customer support following its failure. We’ve had a terrible time trying to get our money back.”

Harbor Freight Daytona 3-ton super-duty floor jack

1 Best Buy0 Worst Buys
Best Buy
Brian Zumbach, Henderson, N.Y. · Vol. 47, No. 3 (2023), p. 14

Brian’s pleased with his Harbor Freight Daytona 3-ton super-duty floor jack. “I use it almost daily, and it’s very well built, especially considering the very affordable price tag.”

On the negative side, “My 2014 Kubota 1140 RTV has spent more time waiting to be repaired than being driven. We’ve had to rebuild both the front and rear ends, and it’s currently waiting for another front-end rebuild.”

Harbor Freight Drill Master electric drills

0 Best Buys1 Worst Buy
Worst Buy
George Carter, Point, Texas · Vol. 35, No. 5 (2011), p. 14

George is disappointed with Harbor Freight Drill Master electric drills. “I’ve used three of these drills this year, and on two of them the chuck broke off the ¿ rst time I used them.”

Harbor Freight During

0 Best Buys1 Worst Buy
Worst Buy
William Mader, Omer, Mich. · Vol. 38, No. 1 (2014), p. 14

William’s had problems with the Chicago Electric 6500-watt generator he bought at Harbor Freight. “During a power outage I ran the generator for two half-days. I shut it off to refuel it and let it sit idle for a few hours, but then it wouldn’t start. It wasn’t getting fuel and wouldn’t start even when I sprayed starting fluid into the carburetor. I checked with Harbor Freight for parts, but hardly any were available. This generator is about 3 years old, and the company says it has been discontinued and that parts for it are no longer available. No more large ticket items for me from Harbor Freight. I finally replaced it with a Powermate generator.”

Harbor Freight Earthquake 1/2-in impact wrench

0 Best Buys1 Worst Buy
Worst Buy
Harold Bevill, Blytheville, Ark. · Vol. 29, No. 3 (2005), p. 12

“My best buy is my HTP Mig 240 welder (HTP America, Inc., Arlington Heights, Ill. ph 800 872-9353). We’ve used it to build toolbars and also to repair and weld derby cars. It always performs flawlessly.”

On the “worst buy” side, he lists his C/P turbo 1/2-in. impact air wrench. “The company rates it at 800 lbs. torque, but I don’t think it’s half that. We quit using it and bought a Harbor Freight Earthquake 1/2-in. impact wrench. It has more power and cost only about one-third as much.”

Harbor Freight Luminar Work 3-watt

1 Best Buy0 Worst Buys
Best Buy
Diana Sutherland, Benton, Ky. · Vol. 39, No. 3 (2015), p. 14

Diana likes her Harbor Freight Luminar Work, 3-watt LED rechargeable cordless spotlight. It charges directly from a vehicle’s 12-volt cigarette lighter socket or any 120-volt outlet to cast a bright beam of light over a wide area, making it perfect for emergency repairs, power outages or hiking and camping trips. It has a cushion pistol grip with trigger lock, protective lens bumper, and an auto shutoff when fully charged.

“It’s very lightweight and has a far reaching light,” says Diana. “It sells for only about $15 but I bought it on sale for less than $10. It works better than the $40 light that it replaced.”

Harbor Freight Portland electric pole saw

1 Best Buy0 Worst Buys
Best Buy
Richard McFadden, Adel, Ga. · Vol. 49, No. 5 (2025), p. 15

Richard nominates his Harbor Freight Portland electric pole saw and Craftsman 10-in. electric chainsaw as best buys. “I’ve been clearing a brush pile from the recent hurricane and cutting 12-in. limbs with no problems.

“The battery on my Black & Decker 20-volt weedeater (LST201) only lasts about 20 min. It’s been doing this since I bought it new. It’s aggravating.”

Harbor Freight Predator 212 cc engine

1 Best Buy0 Worst Buys
Best Buy
Ross Bayer, McDade, Texas · Vol. 42, No. 3 (2018), p. 15

Ross is the satisfied owner of a 2017 Krone 283 3-pt. mounted disc mower. “This is my second Krone 283 and it has been virtually bullet proof. No problems with either machine. These mowers are shaft-driven with no belts to deal with, and the skids they ride on are built heavy. Even the covers are made of heavy-duty material – the cover on my old 283 was in perfect condition when I traded it in.

“My Simpson 3100 psi pressure washer has enough pressure to do a good job, but after several years the original Honda 190cc engine failed. I replaced it with a Harbor Freight Predator 212 cc engine that has performed flawlessly. I’ve had to replace the spray wand on this washer three times because the wands have such poorly made plastic triggers. I also had to replace the pump.”

Harbor Freight Predator 3 hp gas engine

1 Best Buy0 Worst Buys
Best Buy
Andy Yoder, Fort Plain, N.Y. · Vol. 42, No. 1 (2018), p. 14

Andy likes Jake’s Wire Tighteners (www.jakeswiretighteners.com; ph 334 541-4950). “This is the single most time and hassle-saving fence repair device that I’ve ever laid hands on. It consists of a clip that you wind into the fence wire with a crank handle. It won’t break a barbed wire from bending it too sharp. You leave the clip in the fence, and later on you can grab the handle and give the clip another crank or two to retighten the wire, if necessary.

“We bought a Harbor Freight Predator 3 hp. gas engine to operate our sawmill blade sharpener, but even on the warmest days we have to pull 10 times to start the engine. Other Amish farmers in our area have had the same problem with this engine. However, it doesn’t seem to be a problem with 6 1/2 hp. Predator engines and up.

“I’ve always had good luck with Honda engines and never thought I’d switch brands but Harbor Freight sells the 6 1/2 hp. Predator engine for $99 with coupon, whereas a Honda 6 1/2 hp. engine sells for about $300. We’ve used a 6 1/2-hp. Predator engine on our water pump for at least three years, pumping about 700 gal. of water per week, with no problems. I recently bought an 8-hp., 310cc Predator engine to operate our sawdust blower and it runs good, too.”

Harbor Freight Predator 3500-watt inverter generator

1 Best Buy0 Worst Buys
Best Buy
Eli Troyer, Fresno, Ohio · Vol. 43, No. 4 (2019), p. 12

Eli’s impressed with the Harbor Freight Predator 3500-watt inverter generator he bought for $700. “I was a little skeptical about buying it because of the low price, but I’ve put 550 trouble-free hours on it and it has exceeded my expectations. It’s super quiet and runs just like a Honda.”

Harbor Freight Predator 4000 portable generator

1 Best Buy0 Worst Buys
Best Buy
Max Gilbertson, Mammoth Lakes, Calif. · Vol. 43, No. 2 (2019), p. 13

“My 2017 Harbor Freight Predator 4000 portable generator always starts on the first or second pull. It’s rated for a continuous 3,200 watts, which it delivers.”

Harbor Freight Predator 71100 gas-powered pressure washer

1 Best Buy0 Worst Buys
Best Buy
Richard A. Young, DeFuniak Springs, Fla. · Vol. 49, No. 5 (2025), p. 14

Richard is pleased with his Harbor Freight Predator gas-powered pressure washer (model 71100). “This pressure washer is only rated at 3,200 psi, but it cleans better than my 5-year-old Troy-Bilt unit rated at 3,400 psi that refused to run anymore. The Predator starts every time on the second pull. The big 12-in. wheels make it so easy to move around the yard. It makes cleaning stuff a lot more pleasurable, and it works great. No more Troy-Bilt.

“Unfortunately, the new Easy Change oil and filter system that Deere is putting on its riding mowers isn’t easy at all. The alignment arrows on the filter and base don’t align as advertised. It makes you wonder if it’s installed right. And at $56, Deere should be ashamed of this setup. Bring back the older spin-on and off filter they used on the 2012 D110 model that I had. With it, you drained all of the old oil for sure, and you didn’t need a filter wrench. Other than that, I love my S130 lawn tractor.”

Harbor Freight Pro Force cement mixer

0 Best Buys1 Worst Buy
Worst Buy
Anthony Siciliano, Redding, Ct. · Vol. 42, No. 2 (2018), p. 15

“This saw has plenty of power to cruise through 24-in. hardwood logs, cutting them into firewood that we use to heat our 3,000 sq. ft. house,” says Anthony about his 2015 Stihl MS362. “The last chainsaw I bought before this one was back in 1983 – a Stihl 024 model that still works like new.”

He’s disappointed with his Harbor Freight Pro Force cement mixer. “By the time we finished mixing forty 60-lb. bags of concrete mix it was falling apart. We had to tie it together with bungie cords just to complete the job.”

Harbor Freight Salvage Co

0 Best Buys1 Worst Buy
Worst Buy
Alex Thomson, Woodbury, Conn. · Vol. 14, No. 5 (1990), p. 13

Alex Thomson, Woodbury, Conn.: A 1981 Toyota diesel pickup is Alex's “best buy”. “I bought it as a demonstrator with 20,000 miles. The only problem has been some bearings in the transmission. Itnow has 110,000 miles and still runs great.” On the negative side are Taiwanese hand tools sold by Harbor Freight Salvage Co. “The combination end wrenches spread open like a green tree branch, Cutting edges such as chisels are a joke. I've had some luck with 3/4-in. drive socket sets, but that’s it.”

Harbor Freight SKU 58731 tire changer

1 Best Buy0 Worst Buys
Best Buy
Joe Elrod, Manhattan, Mont. · Vol. 49, No. 4 (2025), p. 13

“As a parent of several teens with a whole fleet of cars and ATVs, I’ve saved a tremendous amount of money by purchasing a Harbor Freight tire changer (SKU 58731). I use it to demount and mount new tires for all these various vehicles as they need replacing. Granted, it’s built of low-grade steel, and some points and parts have required repairs and modifications over time. I also use glass balance beads internally in the automotive tires, which are economical and work well instead of having to balance with external weights.”

Harbor Freight reciprocating saw

1 Best Buy0 Worst Buys
Best Buy
Loren Rasmussen, Kokomo, Ind. · Vol. 45, No. 3 (2021), p. 15

Loren is happy with his Harbor Freight reciprocating saw and grinder. “I have bought these saws and grinders several times for myself and my sons. We don’t use them often but have never had one fail.”

Harbor Freight haul-master truck bed

1 Best Buy0 Worst Buys
Best Buy
Bruce Short, New Portland, Maine · Vol. 44, No. 3 (2020), p. 15

“I’ve used my Harbor Freight Haul-Master truck bed cargo unloader at least 100 times and love it. It’s a heavy duty, 14-ft. long by 50-in. wide polypropylene drag sheet designed for 1/2-ton, compact, and step-side pickup beds. The drag sheet covers the entire pickup bed and comes with a roller bar that straps to the tailgate. The operator cranks a 21-in. removable handle to pull loads to the rear.

“Works great to unload firewood as well as topsoil for repairing our lawn. Sells for just $44.99 on the company website.”

Harbor Freight battery blower

1 Best Buy0 Worst Buys
Best Buy
Doug Ameslin, Marshville, N.C. · Vol. 49, No. 2 (2025), p. 15

“My wife likes her Harbor Freight battery blower and weed trimmer. They take the same battery, which lasts a long time.”

Harbor Freight portable car canopy

0 Best Buys1 Worst Buy
Worst Buy
John Wint, Pittsford, N.Y. · Vol. 49, No. 4 (2025), p. 14

“My best buy is my Country Clipper Charger 52-in. zero-turn mower with Kawasaki engine that I bought new in 2021. I’ve had over 200 hrs. of trouble-free mowing. The lift-up mowing deck makes blade changes and cleaning easy. The suspension seat is quite comfortable. I ordered it with joystick steering, and I’m so glad I did. It’s super fun to mow now.”

John is displeased with his 10-ft. by 17-ft. Harbor Freight portable car canopy. “The frames have too big a spread between them, so rain and snow get too heavy and rip out the fabric. I installed extra rafters and purchased a replacement cover. Now the sun has quickly deteriorated the new cover. Just no quality.”

Harbor Freight carries

1 Best Buy0 Worst Buys
Best Buy
Linda Meyer, Speedwell, Va. · Vol. 36, No. 1 (2012), p. 15

“My husband bought me a ‘gadget’ for my car – a 1.5-watt solar panel that plugs into the cigarette lighter – and I think it’s the best thing since sliced bread. It provides continuous charging of the vehicle’s battery and helped my car battery last for 11 years. The batteries in our Dodge diesel pickup lasted for 10 years. Harbor Freight carries this product, and with coupons it usually sells for under $20. I’ve given them as presents to people with ATV’s, and my neighbor uses his on his field tractor.”

Harbor Freight mini-tire changer

1 Best Buy0 Worst Buys
Best Buy
Kelly Best, Tampa, Fla. · Vol. 40, No. 1 (2016), p. 14

“My Harbor Freight mini-tire changer makes it easy to change small tires on lawn tractors, wheelbarrows, and so forth.”

Harbor Freight deep

1 Best Buy0 Worst Buys
Best Buy
Rich Blaskowski, Stevens Point, Wis. · Vol. 44, No. 4 (2020), p. 15

Rich owns a Harbor Freight 5-in. deep cut variable speed, Bauer portable band saw. “I use it for various metal cutting jobs and repair work. I like the portability and it’s easy to change the blades. I bought this saw on sale for about $100.

“I use the battery-operated liquid transfer pump I bought at Harbor Freight to pump gas into my Oliver 1650 tractor. I place a gas can on the loader frame and then transfer the gas up into a funnel on the gas tank. It can pump 6 quarts per min. I bought it on sale for only about $10.”

Harbor Freight battery drills

1 Best Buy0 Worst Buys
Best Buy
Dorothy Courtright, Temple, Okla. · Vol. 47, No. 5 (2023), p. 12

“I love my Harbor Freight battery drills, grinders, and weed eaters. They work great if you respect them and don’t overload them. They’re not made to be used 24/7.”

Harbor Freight electric

1 Best Buy0 Worst Buys
Best Buy
Jim Holt, Cincinnati, Ohio · Vol. 45, No. 4 (2021), p. 12

Jim’s pleased with his Harbor Freight electric ATV/utility winches. “Back in February, 2020 the company began selling their 2,500-lb. rated winches for less than $50 apiece, and that price included a fairlead and remote control. I own about 3 acres of grass with hidden wet patches, where it’s easy to get stuck without warning while mowing, so I installed a winch on both of my riding mowers. Since the mowers aren’t identical, it took a lot of figuring to install them.

“I also installed a winch on my Yamaha golf cart, and plan to install one on my Kioti loader tractor.

“However, I soon learned that a couple of the remote controls on these machines used the same frequencies as other remotes in our area. So I installed a heavy-duty on-off switch on each machine to solve the remote problem.”

Harbor Freight horizontal shaft engine

1 Best Buy0 Worst Buys
Best Buy
Ronald Baker, Lancaster, S.C. · Vol. 44, No. 2 (2020), p. 13

Ronald’s best buy is a 13-hp. Harbor Freight horizontal shaft engine. “I repowered a Simplicity Powermax tractor that originally had an Onan 19 1/2-hp. engine. The Harbor Freight engine had to be inverted to allow the pulleys to turn in the right direction. Once I was able to get everything lined up, it performed great. It has plenty of power for hydraulics.”

Harbor Freight everything

1 Best Buy0 Worst Buys
Best Buy
Steve Stewart, Spokane, Mo. · Vol. 47, No. 3 (2023), p. 14

“I like the Bauer line of cordless tools at Harbor Freight, everything from drills to hedge trimmers. I have a 12,000-lb. excavator with two 3/4-in. bolts that hold the tilt on the cab down. I ran the bolts down with my 1/4-in. Bauer impact driver and then checked them with an 18-in. breaker bar, and they were plenty tight. I keep a drill in every truck.”

Harbor Freight generators

1 Best Buy0 Worst Buys
Best Buy
Berk Palmer, Ridgeway, S.C. · Vol. 40, No. 6 (2016), p. 14

“I’ve purchased several Harbor Freight generators and pressure washers and the engines on all of them have worked flawlessly. These engines appear to be a ‘knock off’ of Honda engines. They run great and are easy on fuel.”

Harbor Freight grinder

1 Best Buy0 Worst Buys
Best Buy
Jon E. Otts, Canastota, N.Y. · Vol. 50, No. 5 (2026), p. 13

“Years ago, I bought a Delta table saw from a Delta dealer. When I began using…”

This listing is from the current issue of FARM SHOW. Subscribe to read it all or get a free issue.

Harbor Freight battery-powered grease gun

1 Best Buy0 Worst Buys
Best Buy
Jeff Tracy, Fair Grove, Mo. · Vol. 34, No. 3 (2010), p. 12

Jeff nominates his Harbor Freight battery-powered grease gun as his “best buy”. “This grease gun has never failed me. The battery on it lasts much longer than I expected, and the gun itself has plenty of pressure to push through plugged-up grease fittings. The only problem is that I stripped the threads on the cartridge cylinder, which was totally my fault because I tightened the cylinder way too tight. The problem was easily solved by borrowing the cartridge from an old grease gun. This grease gun sells for $59, which is a lot less than the $250 battery-powered grease guns sold by other companies.”

On the minus side, he lists Harbor Freight self-adjusting wire strippers. “They’re the cheapest wire strippers I’ve ever seen. I was able to use them only three times before they broke and flew apart.

“Harbor Freight has some good products and some not so good.”

Harbor Freight saw sharpener

1 Best Buy0 Worst Buys
Best Buy
Arnold Andrews, Centralia, Ont. · Vol. 34, No. 2 (2010), p. 15

Arnold’s impressed with the Drillmaster step drills he bought from Harbor Freight. “I do work away from my small shop, and these drills replace a lot of hole saws and drill bits without taking up much room in my toolbox. I use them a lot and they work well.

“My Harbor Freight saw sharpener works well. The flipper that stops the chain could work better, but it’s not a bad unit for $40.”

Harbor Freight cable hoist

1 Best Buy0 Worst Buys
Best Buy
Paul Hoekema, Grand Rapids, Mich. · Vol. 47, No. 4 (2023), p. 15

“I attached my Harbor Freight cable hoist to the ridge pole in my garage and ran wire so it can be run from the garage floor. Very useful for loading heavy items, moving my snowblower to the attic, lifting the garden tractor, etc.”

Harbor Freight hydraulic

1 Best Buy0 Worst Buys
Best Buy
Daniel Beal, Hudson, Mich. · Vol. 41, No. 4 (2017), p. 15

“My Harbor Freight hydraulic ATV/lawn mower lift is easy to operate and returns to the floor gently. It really works nice.”

Harbor Freight aluminum floor jack

1 Best Buy0 Worst Buys
Best Buy
Jack Woodford, Paris, Ky. · Vol. 43, No. 4 (2019), p. 15

Jack’s pleased with his Harbor Freight aluminum floor jack which he bought several years ago. “This little jack is super lightweight and handy for small to medium jobs. No problems.”

Harbor Freight solar LED motion-detection light

0 Best Buys1 Worst Buy
Worst Buy
Paul Duncan, Crestline, Kan. · Vol. 50, No. 3 (2026), p. 12

“My absolute best buy has to be my 2009 Cub Cadet Z Force zero-turn 22-hp mower. It has served me well over the past 16 seasons, with only two idler pulleys and belts needing replacement, and the PTO clutch and PTO switch replaced just last year.

“Another great buy is the 1952 Ford 8N I purchased in 1989. It’ll start in the coldest weather when my utility diesel tractor won’t. I still use the 8N for plowing and discing each year to prepare my garden. I also rely on it for a lot of the snow removal.

“My worst recent purchase is a Harbor Freight solar LED motion-detection light. I bought it in December. It worked for a while after installation, but now it won’t turn on at all. I’ve bought many things from them over the years and had good luck with most, but this light was a waste of money.”

Harbor Freight battery maintainers

1 Best Buy0 Worst Buys
Best Buy
Bob Payne, Coldwater, Miss. · Vol. 42, No. 3 (2018), p. 12

“I use Harbor Freight battery maintainers on my tractors, mowers, trucks, ATVs, and even on batteries stored on shelves. Vehicles that sit for months at a time will start right up.

“With larger batteries on cars and trucks, I hook up the maintainer directly to the battery to produce a constant trickle charge. With smaller batteries such as on riding mowers and ATVs, I use an inexpensive Harbor Freight timer switch. It turns the maintainer on and off several times a day to keep water in the battery cells from evaporating and ruining the battery.

“Harbor Freight sells inexpensive extension cords that work fine with their trickle maintainers. Trickle maintainers sell for about $10 but discount coupons can bring the price down to about $5.

“Eric Schmidt, chief executive officer at Harbor Freight, is working to ‘up their game’ by delivering better quality products at economical prices and I think he’s succeeding. Many manufacturing companies now shop at their stores. I do think it’s a good idea to buy extended warranties for electrical or ‘heavy use’ items that cost more.”

Harbor Freight battery charger never

1 Best Buy0 Worst Buys
Best Buy
Jack Zielsdorf, Grand Coulee, Wash. · Vol. 40, No. 4 (2016), p. 13

“A friend of mine told me that if you want to cure a sore throat, put a drop of Oregano oil on your finger and apply it to the roof of your mouth. So the next time I had a sore throat I tried this idea, and it worked.

“My Harbor Freight battery charger never worked right from the start.”

Harbor Freight electric log splitter

1 Best Buy0 Worst Buys
Best Buy
Patrick Smith, Beaufort, N.C. · Vol. 46, No. 2 (2022), p. 13

“I only split around three cords per year, but the Harbor Freight electric log splitter has done all I’ve asked of it. I couldn’t be more pleased. Plug it in and it splits.”

Harbor Freight backpack sprayer

1 Best Buy0 Worst Buys
Best Buy
Len Mallas, Fond du Lac, Wis. · Vol. 43, No. 6 (2019), p. 15

“Len’s impressed with his 2017 Harbor Freight 4-gal. backpack sprayer. “It’s well-built and works flawlessly. Sells for 50 to 75 percent less than comparable name brand sprayers.”

Harbor Freight product

1 Best Buy0 Worst Buys
Best Buy
Bob Payne, Coldwater, Miss. · Vol. 42, No. 2 (2018), p. 13

“One product at Harbor Freight that ranks as a best buy for me is their industrial rolling toolbox with ball bearing drawer slides. The key is the ball bearings. The 56-in. cabinet has 11 drawers and holds up to 3,458 lbs. of tools. Sells for $749.99. There’s also a 44-in. model.

“Another Harbor Freight product that worked out well is a Pittsburgh Master Ball Joint Adapter kit that’s very handy if you have to change out a U-joint. It presses cups out and back in. So much easier with this tool than trying to use a socket and hammer.”

Harbor Freight pump

0 Best Buys1 Worst Buy
Worst Buy
Colin Smith, Franklin, N.J. · Vol. 49, No. 6 (2025), p. 15

Colin’s impressed with his 2022 Milwaukee M18 tool system. “My battery grease gun failed after several years of spoiling me. I came across a sale at Acme Tools, where I found an M18 Milwaukee kit that included a grease gun and a high-torque 1/2-in. impact. Since I wanted the grease gun and the price was excellent, I bought it. The grease gun is so much better than my old one. It has many nice features. The impact was a surprise. It has more power than I expected, and the battery life is excellent. I’ve since added several M18 tools to my toolbox.

“I’ve discovered that any Harbor Freight pump is a worst buy. They don’t have parts for many of their products, and if a pump fails, they have a special return policy that includes restocking fees, even if the item is only a few days old.

“I purchased a transfer pump and a booster pump to move water over a distance. The transfer pump overheated and slowed to a trickle, even with a booster pump taking some of the strain. The booster pump only moved clear water, which went through the extra pump vane in too short a time, and none were available at the store.”

Harbor Freight put

1 Best Buy0 Worst Buys
Feature storyBest Buy
Jim Ruen, La Crescent, Minn. · Vol. 46, No. 3 (2022), p. 14 · Full story at FARM SHOW →

“I bought a 2-hp. dust collector from Harbor Freight, put it together, and then later returned it for a full refund.”

Read the whole story →

Harbor Freight towable ride-on trencher

0 Best Buys1 Worst Buy
Worst Buy
Marion Smith, Lubbock, Texas · Vol. 40, No. 6 (2016), p. 13

He says his Harbor Freight towable ride-on trencher and Harbor Freight electric chainsaw are both “worst buys”. “Both products worked for a short time and would probably still be working if parts for them were available at the store level, or if I could’ve got help ordering them online. But the company offered no parts and no help. I guess you’re supposed to use their products once and that’s it.”

Harbor Freight plastic welder

0 Best Buys1 Worst Buy
Worst Buy
Gerald Atkins, Westport, Ore. · Vol. 36, No. 6 (2012), p. 15

“My Harbor Freight plastic welder didn’t last 6 minutes before the element burned out.”

Harbor Freight tools work

1 Best Buy0 Worst Buys
Best Buy
Jerome Sprong, Meppen, Ill. · Vol. 37, No. 1 (2013), p. 14

“I’ve found that Harbor Freight tools work best for light duty use. I think their customer service is excellent. I bought an air stapler which turned out to be defective, so I called the company and they immediately sent a new stapler at no cost.”

Read every report in full

FARM SHOW has run reader Best & Worst Buys since the beginning.

Subscribe to FARM SHOW