Real farmers rate what they bought, from FARM SHOW MagazineSubscribe  ·  Free issue  ·  Send us your Best or Worst Buy
Subscribe to FARM SHOW
Home › Issues › Vol. 37, No. 2 (2013)

Best & Worst Buys: FARM SHOW Vol. 37, No. 2 (2013)

68 reports from pages 12–15 · 64 Best Buys9 Worst Buys · See everything in this issue at FARM SHOW →

Best Buy

Lanair MX 150 waste oil furnace

Randy Okerman, Port Townsend, Wash. · Vol. 37, No. 2 (2013), p. 12

Randy likes his 2006 Lanair MX 150 waste oil furnace. “It’s safe and clean with no smoke or smell. We got personal attention from the manufacturer when needed. Low maintenance. I run it about 400 hrs. annually, burning about 400 gal. of waste oil. All I have to do is screen and dewater the oil, vacuum out burner ash occasionally, and brush the burner ring yearly.”

Best Buy

Guide Gear light

Mark Newhall, Lakeville, Minn. · Vol. 37, No. 2 (2013), p. 12

“I bought my first LED flashlight 2 years ago and I couldn’t be happier. The batteries seem to last forever, and it’s as bright as any flashlight I’ve ever owned. It’s a Guide Gear light I bought at Amazon.com. The exact model I have is no longer available but there are many similar ones. The great thing about the LED light is that it uses much less power and doesn’t get hot. The batteries last longer and the bulbs don’t seem to wear out.”

Best Buy

Ford Raptor 4-WD pickup + 1 more

Katharina M. Lauer, Stillwater, Penn. · Vol. 37, No. 2 (2013), p. 12

“My 2012 Ford Raptor 4-WD pickup is an engineering marvel and an operator’s dream from its moon roof and full leather seats to its full line of superior electronics. It’s a complete ‘wow’ to own.

“Another great product, also made in America, is my Retrax pro bed cover system custom-made to fit on my extra wide Raptor short bed (www.retrax.com). It was simple to install and looks good on the truck. It opens and closes easily by hand, locking at any location. It’s a luxurious-looking, superior functioning unit that’s very well designed.”

Best Buy

Echo gas-powered pole pruner

Mike Bordovsky, San Antonio, Texas · Vol. 37, No. 2 (2013), p. 12

“I use my Echo gas-powered pole pruner to clean out fence lines. It’s like a chainsaw on a stick and is perfect for getting in and under brush and cactus. Using a regular chainsaw, you have to crawl in and often get scratched up getting at the base branches, trimming them away or pushing through them to get at the trunk.

“With the pole pruner, I have an 8-ft. reach and can stand away from the branches, yet reach in to trim them or cut the trunk. It’s also great for getting between barbwires to reach branches and trunks on the other side of the fence. It’s easy to control because the small gas engine balances the weight of the cutting bar.”

Best Buy

Staber clothes washing machine

Douglas F. Siadak, Liberty Center, Ohio · Vol. 37, No. 2 (2013), p. 12

“I looked forward to the arrival of our new 2006 Staber clothes washing machine with its supposed money-saving features. However, within the first year our troubles began. First, a set of bearings suspending the wash drum went out. The warranty covered the cost of new bearings, but I had to install them. Two or three years later another set of bearings went bad and I had to pay for those, too.

“The next problem was more expensive. A circuit board blew out and cost almost $300 to replace. Now the rubber diverter around the top is ripped, and I’m afraid to inquire about the price of a new part. I’m not a spring chicken any more so repairing this machine has become a burden. When I purchased this expensive unit I expected at least 10 years of trouble-free service.”

Best Buy

Cub Cadet 1125

Darin Bartholomaus, Mora, Minn. · Vol. 37, No. 2 (2013), p. 12

“I like my 2005 Cub Cadet 1125 series riding mower equipped with a Kawasaki 17 hp engine. It runs great and has plenty of power. It does a great job cutting grass, and I’ve used it with a trailer to haul several cords of firewood out of the woods.”

Worst Buy

Hesston 4650 small square baler

Jay Ledbetter, Stanford, Mont. · Vol. 37, No. 2 (2013), p. 12

“My Hesston 4650 small square baler, which I bought used, is my worst buy. My Deere 346 baler had been having problems so 5 years ago I bought the Hesston model sight unseen from a local dealer. He said their service department had gone completely through the baler and that it was ready to go.

“I took the machine home, loaded it up with twine, greased and lubed everything and started baling. On its fourth bale it sheared off the needles, which cost $385 to repair. A week later I started in the field again and it worked great for 26 bales and then it threw a no. 60 chain. Soon after, a bearing on the fingers carriage seized, at a repair cost of $285.

“Now I have more than $10,000 tied up in a baler that to date has made 57 bales. This has gone way past a worst buy and might just be criminal. By the way, the old Deere 346 still works and turns out beautiful bales.”

Best Buy

Grasshopper mowers + 1 more

Jack Justice, Hebron, Ohio · Vol. 37, No. 2 (2013), p. 12

“My wife and I couldn’t be happier with our Grasshopper mowers (ph 620 345-8621; www.grasshoppermower.com). We mow about 10 acres, much of it wooded, and these mowers never let us down. We’ve relied on Grasshopper mowers for more than 30 years and wouldn’t have anything else. We currently have a 10-year-old 725K front-mount model and just replaced a 26-year-old 718K model with a 620T model. The 718 model was still running strong but I felt I should replace it before I retire.

“At about 2,300 hrs the 718 model developed a hydro problem with one of the drives. Grasshopper Service out of Kansas provided a rebuilt unit at a reasonable price. The Grasshopper vacuum attachment does an outstanding job, and you just can’t beat its capacity and ease of operation.

“My dad’s best buy was a 1953 Allis Chalmers WD tractor that he bought new. This tractor was the workhorse on our dairy farm. It ran day and night in the spring and fall for many years, requiring little more than tires and routine service. The tractor is now semi retired, but it still starts without fail and purrs like a kitten.”

Best BuyWorst Buy

Stihl MS290 Farm Boss chainsaw sets idle + 1 more

Mike Crawford, Bradford, Penn. · Vol. 37, No. 2 (2013), p. 12

“Even if my Stihl MS290 Farm Boss chainsaw sets idle for 3 to 4 mos., I never have to pull more than twice to get it started. My Stihl FS45 trimmer also starts right up. When this trimmer was 6 years old, I accidentally jammed it with heavy grass and spun out the drive hex in the plastic head. I took the broken head off to have the dealer replace it. I had forgotten about the company’s lifetime guarantee on the head, but the dealer hadn’t. When I picked up the trimmer two days later it had a new head and there was no charge.

“I had a lot of trouble starting my Stihl BG55 leaf blower right after I bought it. I had to pull 8 to 10 times before it would start. I returned it to the dealer, who had me try to start the unit while he watched. I left the blower with him and they found a pinched gas line. From that day on, the blower has always started right up with just one pull.”

Worst Buy

John Deere LA145 riding mower equipped

Donna Hohlt, Kinmundy, Ill. · Vol. 37, No. 2 (2013), p. 13

Donna’s disappointed with her Deere LA145 riding mower equipped with a 48-in. deck. “We had to replace two belts in the first 6 mos. as well as wheel bearings, and it’s a continuing problem. We’ve discussed these problems with the dealer, but they just say that we bought a ‘town mower’ and that our yard is too big for it.”

Best Buy

International Harvester DT-466 diesel engine

Terry Younts, Thomasville, N.C. · Vol. 37, No. 2 (2013), p. 13

Terry’s 1975 International DT-466 diesel engine rates as his “best buy”. “We used this engine for years to power a sawmill, putting on about 18,000 hrs. The water pump was replaced twice and a copper O-ring under a fuel injector was also replaced. The engine ran at 2,100 rpm’s and at 178 degrees, both summer and winter. We always used Delvac 1330 heavy duty diesel engine oil in it.”

Best Buy

My two best buys are the 4-WD articulated tractors I built

Richard Steward, Grovespring, Mo. · Vol. 37, No. 2 (2013), p. 13

“My two best buys are the 4-WD articulated tractors I built. The first one was built in 1968 when I was living in northern Minnesota raising cattle and hay. I also logged out and sawed lumber to sell.

“I needed a 4-WD and couldn’t afford it, so I built one. I used it for everything – feeding cattle, handling hay, and logging. It worked so well that I built a second one in 1988. Then I could leave one in the timber and the other at my sawmill.

“Both of them are based on Allis Chalmers WC’s. I used frames and the differential from the WC’s. The first one has a GMC V-6 engine with a Davis industrial loader. The second one is similar, but has a 318 cu. in. Dodge engine and a stronger, heavier loader.

“The center joints articulate and oscillate so they can flex over rough and frozen ground. The loader frames were also made from WC frames.

“I raised 8 kids and ran between 250 and 400 head of cattle while working with those two tractors in Minnesota. Now the kids are grown and gone, and I live in Missouri. I still use both tractors on a daily basis, running 100 head of cattle and logging out timber.”

Best Buy

Case IH 7110 tractor + 1 more

John W. Carroll, Pontiac, Ill. · Vol. 37, No. 2 (2013), p. 13

“My Case IH 7110 tractor works great and is a pleasure to operate.

“We use our 1997 Wood-Mizer sawmill to do custom sawing, and in 1998 we used it to help build our log home. It has sawed a lot of lumber and has paid for itself many times over. We’ve had some repairs on electric parts and replaced a couple of bearings, but we are always able to get the problem resolved over the phone and the replacement parts arrive in one or two days. The only negative is that the paint job isn’t too good.”

Best BuyWorst Buy

Ram 1500 Quadcab pickup equipped + 1 more

Doug White, Unity, Sask. · Vol. 37, No. 2 (2013), p. 13

“In a recent issue Timothy Weihert described intermittent starting problems with his 2008 Dodge Ram 1500 Quadcab pickup equipped with a 4.7-liter engine. The engine would turn over but wouldn’t start. This was a common problem with Ford, Chevy and Dodge pickups in the 1970’s and 1980’s. My 1976 Ford F-150, 1978 Ford F-100, 1980 F-600, 1981 F-100, and 1984 F-150 pickups have all had this problem. The problem was with the solid state ignition module which was mounted on the fender well, except on the 1984 model where it was mounted on the distributor. The module only took about 15 min. to change, and I always carried a spare one with me and the tools to change it.

“I’ve been buying pickups for 47 years, and my favorite is my 2007 Dodge Ram 1500 Mega Cab equipped with a 5.7-liter Hemi engine.”

Best Buy

Chevrolet Silverado 2500 HD pickup equipped

Ken Laboski, Fitchburg, Wis. · Vol. 37, No. 2 (2013), p. 13

“I like my 2003 Chevrolet Silverado 2500 HD pickup equipped with an 8.1-liter gas engine and Allison transmission. This pickup has only broken down once, and that was due to a dead battery. The engine/transmission combination is awesome for towing heavy loads. I can pull 12,000-lb. loads with a weight distributing hitch, yet barely feel the trailer behind me.”

Best Buy

Toyota Tundra pickup + 1 more

Duane A. Johnson, Parkersburg, Iowa · Vol. 37, No. 2 (2013), p. 13

“My 2007 Toyota Tundra pickup works even better than I expected. It pulls any load without hesitating.

“I really like my three Gehl skid loaders. I’ve put about 12,000 hrs. on my 1996 3825 model; 10,000 hrs. on my 2002 4635; and 900 hrs. on my 2011 5240. All have performed with minimal downtime and required only routine maintenance.”

Best BuyWorst Buy

Case New Holland JX1060C 50 hp tractor + 1 more

Don Enlow, Jonesville, La. · Vol. 37, No. 2 (2013), p. 13

“With less than 200 hrs. on my 2007 Case New Holland JX1060C 50 hp tractor, the hand throttle cable broke and had to be replaced. Now with 481 hrs., the replacement cable has also broken. I called the company to see if they had a recall, but they just said I should take the tractor to the dealer for repairs.

“Instead, I ordered a flexible control hand throttle cable through Messick’s and will replace it myself. I want to know why New Holland won’t declare a recall on their throttle cable, as I know other owners of New Holland tractors with the same problem.

“I kept both my Deere 2003 JX345 riding mowers inside a building whenever I wasn’t using them, yet the seat cushion on both has come loose from the frame. The company needs to fix this problem on all its riding mowers.”

Best Buy

JCB 409B + 1 more

Rocky Fowler, Tiffin, Ohio · Vol. 37, No. 2 (2013), p. 13

“My JCB 409B is a small payloader but can lift up to 8,000 lbs., and it bends in the middle so it doesn’t tear up the ground on turns. This payloader costs and weighs about the same as a large skid loader, but is easier to get on and off and has a much better ride.

“My Tapco aluminum siding brake works great on the farm for building repairs and for new construction (www.tapcotools.com). It’s easy to use.”

Best Buy

Cyclone Rake lawn vacuum system

Michael Myers, Fredonia, Kan. · Vol. 37, No. 2 (2013), p. 13

“Our Cyclone Rake lawn vacuum system works great for picking up leaves (ph 888 531-7253; www.cyclonerake.com). I use this machine on back of my garden tractor every fall all over our small town. The engine provides a lot of suction and could even pick up something as heavy as half a brick if you’re not careful. Also, the company backs up its product. If you need anything at all they’re always willing to help.”

Best Buy

Spectra Gl412 grade laser

Elwin Gingerich, Kalona, Iowa · Vol. 37, No. 2 (2013), p. 13

“I really like my Spectra Gl412 grade laser with the CR600 receiver, which comes with a rod clamp and magnetic base to go on the machine (ph 888 844-3765; www.tigersupplies.com). The Gl412 is easy to set up, and you can also use a mask mode to turn off one to three windows of laser if working around other lasers.

“The CR600 receiver has a 5-in. receiver window with a 180 degree receiver window, and has bright red and green arrows that can be turned on and off and are highly visible from the machine. It also comes with a remote to change the grade while away from the laser.”

Best Buy

GM 4-door dually pickup equipped

John Holt, Clifton, Texas · Vol. 37, No. 2 (2013), p. 13

“It had about 135,000 miles on it when I bought it, and now has about 402,000 miles,” says John about his 1994 GM 4-door dually pickup equipped with a 6.5-liter diesel engine and automatic transmission. “The engine was replaced at about 68,000 miles. I change the oil and filter every 2,500 miles. I rebuilt the transmission once myself and rebuilt all the front suspension. I’ve put on a couple water pumps and changed the fuel injectors once. The engine has never had the injector pump or turbocharger replaced. It gets about 15 mpg.”

Best Buy

Cannonball truck-mounted bale bed

Ron Say, Alta Vista, Kan. · Vol. 37, No. 2 (2013), p. 14

“I like my Cannonball truck-mounted bale bed (ph 620 532-3675; www.cannonballengineering.com). It comes with lift arms that are independent of each other, which makes centering the bale an easy job. It also works great to spin bales 90 degrees when they’re stacked end to end. The arms can also be used to lift the bed to dump the load.”

Best Buy

Yukon Big Jack wood furnace

Marc Lever, Clatskanie, Ore. · Vol. 37, No. 2 (2013), p. 14

“It performs exactly as advertised,” reports Marc about his 2010 Yukon Big Jack wood furnace (ph 800 358-0060; www.yukon-eagle.com). “This unit is quite efficient and keeps our 1907-built farm house at 72 degrees with ease. The manufacturer was great to deal with, answering all our questions during installation. Overall, it’s a well-built, heavy duty unit that should last a long time.”

Best BuyWorst Buy

Valtra A-95 tractor equipped + 2 more

Arnold Colson, Corinth, Ky. · Vol. 37, No. 2 (2013), p. 14

“I replaced my Deere 2955 tractor with a 2007 Valtra A-95 tractor equipped with a cab and frontend loader, and was shocked at the fuel savings alone. I had been told that the Susi engine in this tractor was fuel efficient, but until you own one you won’t believe it. I love the heavy-built loader. This is a heavy, well-built tractor. I hope AGCO can make a Massey tractor this good that’s equipped with the Suzi engine.

“My Kuhn 10-wheel Speed Rake is awesome. It’s built heavy and saves a fortune in fuel compared to my old New Holland bar rake.

“The oil filter on my Polaris 4-wheeler is in a terrible location, and many components are hard to access due to poor design. It’s a shame, too, because this product is American-made.”

Best Buy

Gensco steering tires

Chris Uebelhoer, Cambridge, Idaho · Vol. 37, No. 2 (2013), p. 14

“I bought two Gensco steering tires for our Allis Chalmers 190 loader tractor (ph 800 828-3350). We use this tractor to feed livestock and had previously suffered many flats using standard farm tires, so we thought we’d give Gensco’s used airplane tires a try. We put them on last April and haven’t had any flats since. However, one tire developed a flaw where the cap was attached. I called the company and they instantly sent us a new tire and wheel, with no questions or excuses. This company stands behind its product, which is rare these days.”

Worst Buy

Arctic Cat ATV

Don Best, Blanket, Texas · Vol. 37, No. 2 (2013), p. 14

Don’s “worst buy” is his 2003 Arctic Cat 250cc ATV. “The first few years after I bought it, I didn’t use it much because it took so long to start and to warm up before I could use it. Then a few years ago I started using it more, and one day in the middle of a dry pasture it started smoking on front where the wiring harness goes through a metal clip to the controls on the handlebars. The machine almost caught fire before I could disconnect the battery.

“I loaded the ATV up and took it to my shop. After checking it out, it was clear the wiring had shorted out where a metal clip holder rubbed against it. I also discovered the wires were all black-taped together with no other protection. I looked at other ATV brands and the wires on them weren’t taped together, but instead had heavy insulation and protection and the part holding the wires was also insulated.

“I called both the dealer and the corporate office, but they weren’t interested in hearing what happened, nor were they willing to give me a replacement wiring harness, even though this was clearly a factory defect because when the wires shorted out, they caught on fire and melted the insulation and wires together. After several hours I was able to rewire everything properly.

“I can’t believe a company this large would tape the wires together. And then to have a metal contact on the clip holding the wires? It was just a matter of time until it shorted out, because the wires flex and pull as you steer and turn from side to side.”

Best Buy

New Holland 672 disc mower + 1 more

James Rainey, Glen Allen, Mo. · Vol. 37, No. 2 (2013), p. 14

“Our 2010 New Holland 672 disc mower cuts great and doesn’t pull the tractor to death like others we’ve owned. It’s a great machine.

“Our 2012 Dodge Grand Caravan has come close to getting us killed. When we step on the accelerator it hesitates, which makes merging into traffic dangerous. When driving on hills the engine just keeps pulling down, and then when it does accelerate it jerks you and sounds like an airplane taking off. We’re Chrysler fans and all our trucks and other vehicles are Chryslers, but in the future, we’ll think hard before buying from them again. The dealer won’t do anything to help.”

Best Buy

SAMCO plastic laying unit

Steve Groff, Holtwood, Penn. · Vol. 37, No. 2 (2013), p. 14

“I’ve used my SAMCO plastic laying unit (Vol. 34, No. 2) on my sweet corn for 6 years. It helps me get my sweet corn to market 7 to 10 days ahead of other growers for premium prices.

“I no-till plant sweet corn in twin rows, 19 in. apart, letting me cover two rows at a time with the SAMCO. The plastic warms the soil, and the corn emerges faster than uncovered rows.

“Once the plants emerge and reach the 4 to I cut through the plastic. I just run a single coulter mounted to a simple toolbar on the tractor between each pair of rows. The coulter slices the thin, photo-degradable plastic and releases the plants.

"Slitting the plastic is important as it allows the plants to grow without having to break through the plastic themselves.

"The SAMCO unit was definitely a best buy, but as I no longer grow sweet corn, I have it for sale for $1,500 (ph 717 284-5152).”

Best Buy

Diesel Tunes Workhorse module

Don Clark, Witts Springs, Ark. · Vol. 37, No. 2 (2013), p. 14

Don bought a Diesel Tunes Workhorse module to boost performance on Dodge Cummins diesel engine (ph 800 264-5102; www.dieseltunes.com). “There are a lot of modules out there and programmers that make big claims. I’ve tried several of them, but I think the Workhorse module is best. It comes with an adjustable knob, which I mounted on my pickup’s gearshift lever, that’s used to select the power range from stock to max. You can really tell the difference this module makes with the engine running at 1,000 rpm’s. Where stock programming would lug the engine down, the Workhorse makes it scoot.”

Best Buy

Voltman Batteries

Bradley Potter, Lowell, Mich. · Vol. 37, No. 2 (2013), p. 14

“After reading an article in FARM SHOW about a battery rebuilder, I thought I’d give it a try. The battery in my 12-volt cordless drill didn’t work any more so I sent it to Voltman Batteries (ph 419 526-1570; www.voltmanbatteries.com). I enclosed a check for the repair along with the battery. Five days later, the battery came back. I’ve used it off and on for 3 mos. now, and it works great. It holds a good, long charge and has as much or more power than before. I’m well satisfied with the quick turn-around and with the battery’s performance. I’d recommend this company to anyone.”

Best Buy

Wolverine Nursery spades

Ed Capron, Whigham, Ga. · Vol. 37, No. 2 (2013), p. 14

“One of the finest digging tools you’ll ever own is one you’ve probably never seen. Wolverine Nursery spades (ph 800 787-3562; www.surelocedging.com) come with 15-in. heat-treated, extra thick, chromoly steel blades made from one-piece welded construction. These spades have 50-in. alloy steel handles that are a full 1 1/2 in. in dia. and come with a 5-year warranty. They work great for lifting bulbs, dividing perennials, cutting sod or pruning roots. They’re the landscaper’s secret weapon.”

Best Buy

Rake Master grapple

Cody Beard, Grandview, Texas · Vol. 37, No. 2 (2013), p. 14

Cody likes his Rake Master grapple (ph 850 584-4494; www.rakemaster.net). “I recently completed demolition of a 50 by 90-ft. hay barn that had been partly destroyed by a tornado. Using this grapple I was able to pull down the barn’s sides and roofing, and even dislodge the cement footing around the barn.”

Best Buy

Brower energy free waterers

Miles Wellman, West Point, Iowa · Vol. 37, No. 2 (2013), p. 14

“I’ve used Brower energy free waterers with my hogs and cattle since the 1990’s and am sold on them (ph 800 553-1791; www.browerequip.com). These waterers even work in temperatures down to zero, though they work best when there’s enough demand that the water turns over at least once a day. Because of the waterer’s design, animals can’t dirty them up with manure.”

Best Buy

Chevrolet Colorado LT1 extended cab 2-wd

Kenneth D. Fencl, Prague, Neb. · Vol. 37, No. 2 (2013), p. 14

Kenneth’s happy with his 2010 Chevrolet Colorado LT1 extended cab 2-WD pickup equipped with a 5-cyl. engine. “This is a good midsize pickup with a lot of power, and it gets a respectable 25 mpg. The cab is roomy, easy to get in and out of, and rides good. Also, when equipped with the factory trailing package this pickup can pull a lot. It’s an all-around good pickup.”

Best Buy

Soil Warrior

Michael Owens, Holloway, Minn. · Vol. 37, No. 2 (2013), p. 14

“It’s a well-built machine for strip tilling in any field conditions,” says Michael about his 16-row Soil Warrior (ph 507 645-2268; www.soilwarrior.com). “The thing I like most about this machine is that it uses coulters. As a result you can use it either in the fall or spring, compared to a shank-type machine that can only be used in the fall. It’s a great machine.”

Best Buy

Ram pickup equipped

John W. Martin, La Crescent, Minn. · Vol. 37, No. 2 (2013), p. 14

A 2004 Dodge pickup equipped with a Cummins diesel engine rates as John’s “best buy”. “It has more than 130,000 miles on it with only one minor problem, which was covered by the warranty. This pickup starts right up in cold weather without being plugged in and has a comfortable ride. It also gets good mileage when pulling a load.”

Best Buy

John Deere 5660 combine equipped

Steve Weisbrod, Canastota, N.Y. · Vol. 37, No. 2 (2013), p. 14

Steve likes his Deere 5660 combine equipped with a 6-row corn head. “Awesome performance. Hills and sidehills don’t slow it down. This is my first rotary combine, and I’m impressed with the clean grain sample and minimum grain loss. My only complaint is the cab is noisier than it should be.”

Best Buy

Blair Equipment Co

Craig Spierling, Levering, Mich. · Vol. 37, No. 2 (2013), p. 14

Craig likes the spotweld cutter kit and Rotabroach sheet metal hole cutter kit he bought from Blair Equipment Co. (ph 810 635-7111; www.blairequipment.com). “I bought their 3/8-in. spotweld cutter to remote spotwelds on my son’s car. I liked it so much that I bought their sheet metal hole cutter kit. It lets you cut 1/4, 5/16, 3/8, 7/16, 5/8, and 3/4-in. dia. holes. I use these cutters instead of drills because they cut much faster without burring the hole. I bought the kit on Amazon.com.”

Best Buy

Harbor Freight

Delbert Hayes, Norwalk, Iowa · Vol. 37, No. 2 (2013), p. 14

“From Harbor Freight I bought a low cost, heated razor blade decal remover and used it to remove two ‘slow moving vehicle’ decals on a grain cart. It took only a short time to do and left the cart’s surface smooth.”

Best BuyWorst Buy

Jeep Liberty Sport 4-WD model equipped + 1 more

Gary Gunderson, Elkhorn, Wis. · Vol. 37, No. 2 (2013), p. 14

“It’s the best compact sports utility vehicle we’ve ever owned,” reports Gary about his 2003 Jeep Liberty Sport 4-WD model equipped with a 3.7-liter V-6 engine, 5-speed transmission and 3-in. suspension lift. “It’s easy on fuel and can handle any kind of terrain or snow.

“I’m disappointed with my 1998 Dodge Dakota extended cab 4-WD pickup equipped with a 318 cu. in. V-8 engine. I’ve replaced everything on the front end and gone through wheel bearings, two oxygen sensors, a water pump and head gaskets. This vehicle has a terrible heater for a fully loaded, mid-sized truck. It only has about 97,000 miles on it.”

Best Buy

Napoleon model 1900 in-house

Bryan L. Schneider, Eden, S. Dak. · Vol. 37, No. 2 (2013), p. 15

Bryan’s impressed with his 2009 Napoleon model 1900 in-house wood stove (ph 800 461-5581; www.napoleonfireplaces.com). “I can’t say enough good things about this stove. We use it to heat our 30 by 50-ft. ranch-style home, which it does with ease. We burn seasoned ash and oak, which it burns clean. It’s a well-made stove. I’d recommend it to anyone.”

Best Buy

New Holland TL1525

Darrick Caisse, Chaplin, Conn. · Vol. 37, No. 2 (2013), p. 15

“It’s the best little tractor I’ve ever owned,” says Darrick about his New Holland TL1525. “It handles jobs I wouldn’t expect it to. It’s super reliable and super efficient, and I bought it at a great price. It’s small enough to fit in my garage and always starts right up. Also, all the parts on it are metal – no plastic.”

Best Buy

Kubota 2230 4-WD tractor equipped

Roger Larson, Lebanon, Mo. · Vol. 37, No. 2 (2013), p. 15

“I like my Kubota 2230 4-WD tractor equipped with a quick-disconnect front-end loader and 60-in. mower deck. This tractor has about 22 hp and does just about everything I ask it to. We also own a Kubota 50 hp model, but the 2230 can do almost as much work. I’m sold on Kubota.”

Best Buy

Bailey’s smart-splitter log splitter

Gregory Sprigg, Basye, Va. · Vol. 37, No. 2 (2013), p. 15

“I like my Bailey’s Smart-Splitter log splitter (ph 800 322-4539; www.baileysonline.com). It’s effective on small to medium-size wood and on larger pieces of already-split firewood. It lets me safely and precisely split kindling without the danger of swinging a hatchet, and it doesn’t burn any fuel. Works great.”

Best Buy

Honda Ridgeline

Bill Hoefer, Shepherd, Mont. · Vol. 37, No. 2 (2013), p. 15

“My 2008 Honda Ridgeline can’t be beat for driving on ice and snow. It’s a front wheel drive vehicle, but when needed the rear wheels kick in faster than lightning. It’s a stable and sure-footed vehicle. I’d like to trade some power for mileage, though. It averages 20 mpg but has more power than I need.”

Best Buy

TP Tools & Equipment

William Hinckley, West Bend, Wis. · Vol. 37, No. 2 (2013), p. 15

“I like the HVLP paint spray system I bought from TP Tools & Equipment (ph 800 321-9260; www.tptools.com). “It uses a 115-volt turbine so you don’t need compressed air. It’s easy to use and you don’t get much overspray. The turbine warms the air so moisture is eliminated, which also helps the paint dry faster. The paint is always left dry and oil free.”

Worst Buy

Kubota zero-turn riding mower

Robert Johnson, Sieper, La. · Vol. 37, No. 2 (2013), p. 15

“In August 2009 I bought a Kubota zero-turn riding mower equipped with a 48-in. deck and grass catcher. I have a small farm and mow about two acres. The first time I used this machine without the grass catcher and it burned 7 gal. of gas in just 3 hours. Another problem was that when I turned the ignition off the engine would keep running, and when it finally quit running it would backfire.

“I called the dealer, but he said he didn’t know what was wrong. He didn’t ask me to bring the mower in, either. So I called the company’s southern district and got the same answer. Next I called the head office in California, and they told me to take the machine in to the dealer. My reply was, ‘why, when they don’t know what’s wrong?’. I was getting the run-around while the warranty was running out. So I wrote two letters to the company headquarters in Japan, but got no reply.

“Finally the dealer picked the machine up and worked on it. He told me he changed the carburetor, but I could see no evidence of wrenches put on the engine. The machine did burn a little less fuel, but still too much, and it continues to backfire when the ignition is turned off. Then a bearing went out on the deck and I had to take the machine back to the dealer, 36 miles one way, with the warranty about to expire. They did, however, repair it under warranty. The mower had only about 90 hrs. on it when the bearing went out.

“The machine’s zero turn feature is defeated by the rear wheels being wider than the deck. The belt lock won’t stay locked in on the grass catcher, so I designed a spring lock to hold it in place. And the engine still backfires.”

Best Buy

Ford F-150 pickup

Mike Taylor, Helena, Ark. · Vol. 37, No. 2 (2013), p. 15

Mike’s the owner of a 2012 Ford F-150 pickup. “This pickup rides smooth and is equipped with a 3.5-liter EcoBoost gas engine, which is adequate. However, it has the poorest headlights of any vehicle I’ve ever owned. I had to put reflectors up where I turn off the highway to go home at night, because I got tired of backing up on the highway after missing the turn. Also, I miss getting to see the neighborhood deer herd – the headlights are so poor that they don’t even look up when I come through.”

Best Buy

Case IH 7120 Magnums

David Martin, Moorefield, Ont. · Vol. 37, No. 2 (2013), p. 15

“Over the years we’ve owned and operated numerous tractors, but few have been as dependable as our Case IH 7120 Magnums. We own a pair of 7120’s, and they’re the workhorses on our dairy farm. Day in and day out, these tractors perform trouble-free. They’re simple to operate, packed with all the power you need, fuel efficient, and functional. They’re also comfortable to operate. I’d recommend them to anyone.”

Best Buy

Sears & Roebuck catalog

William H. Young, Cottage Grove, Ore. · Vol. 37, No. 2 (2013), p. 15

“In 1941 my father ordered for me, from the Sears & Roebuck catalog, a 6 by 18-in. metal cutting bench lathe, which was a substantial and expensive Christmas gift for a 16-year-old. I later became a machinist after serving a 6-year apprenticeship program. I still have the original operating instructions for the lathe, and the parts list.

“Last year I overhauled the lathe and was surprised to find that the part numbers on it are identical to the part numbers in the company’s 2012 parts catalog. The only difference is that the prices have risen tremendously. I’m very proud of this 71-year-old, made-in-the-U.S. lathe. It has served me well and over the years has needed only minor parts replaced.”