Real farmers rate what they bought, from FARM SHOW MagazineSubscribe  ·  Free issue  ·  Send us your Best or Worst Buy
Subscribe to FARM SHOW
Home › Brands › Vermeer

Vermeer: what farmers say

120 reports in FARM SHOW · 104 Best Buys16 Worst Buys

Vermeer (general)

25 Best Buys6 Worst Buys
Best Buy
Laurence Sanderson, McLouth, Kan · Vol. 19, No. 3 (1995), p. 15

Laurence Sanderson, McLouth, Kan.: A 1993 Case-IH 5220 tractor and a 1980 Vermeer 6S0F round baler are two of Laurence’s “best buys”. “The Case starts at low temperatures with no problems. The 3-pt. has tremendous lift capacity, so much that I’ve already bent two mounted implements. The Cummins diesel engine is very fuel efficient. The Vermeer baler is built like a tank. I've had to replace only two bearings and the drive chain in 15 years. In my opinion it makes a tighter wrapped bale than any other baler on the market,”

Best Buy
Olin Rairdon, Indianpolis, Ind. · Vol. 18, No. 5 (1994), p. 15

Olin Rairdon, Indianpolis, Ind.: Olin operates a stump cutting business using a Vermeer 2460 stump cutter and a smaller Can Do self-propelled model for grinding stumps that the Vermeer unit can’t reach. He uses a 1964 Deere 3020 tractor equipped with a Westendorf front-end loader to pull the Vermeer and hauls both stump cutters as well as the tractor on a 30-ft. gooseneck trailer between jobs. “The Vermeer stump cutter was originally powered by a Wisconsin 65 hp 4-cyl. gas engine. It kept failing every six or seven months because dirt got through the air cleaner filter. I replaced the engine with a Deutz 950 diesel equipped with an oil bath air cleaner and also mounted an in-line fuel filter in front of the fuel pump. I had the same problem with the 20 hp Kohler engine on the Can Do cutter so I replaced it with a Ruggerini MD 151-D 15 hp diesel engine equipped with an oil bath air cleaner. The engine is made in Italy and sold in the U.S. by Deutz. It developed an oil leak after the warranty expired. My dealer's mechanic found that the problem was caused by a crack in the block. He explained the problem to a Deutz representative who replaced the engine at no cost except for installation. “Engines used in dusty conditions shouldn't have dry-type air cleaner filters. My 1964 Deere 3020 tractor has an oil bath air cleaner and has been overhauled only once.”

Worst Buy
Vic Stratman, Argyle, Mo. · Vol. 18, No. 2 (1994), p. 16

Vic Stratman, Argyle, Mo.: Vic says his “best buy” is his 1990 Chevrolet Astro Van equipped with a 6-cyl. engine. “It had a lot of problems at first but the dealer solved them. Now it works great.” On the negative side, “My Lincoln pistol grip grease gun costa fortune and I couldn't keep air out of it.” “My 1992 Vermeer 605E round baler is also a worst buy. I thought the Vermeer name meant quality. However, I found out that the 605E wasan experimental baler that had had a lot of problems, That’s.an understatement. It wasn’ ttoo bad the first year but last year everything on it broke that could. Finally the gearbox went out. That was it. Anyone need parts for a 605E? I’m junking this one.”

Best Buy
David Otting, Clearbrook, Minn. · Vol. 13, No. 2 (1989), p. 13

David Otting, Clearbrook, Minn.: “Thanks to FARM SHOW, my best buy is a 12-wheel rake I first read about in an issue last year. The rake narrows to 8 ft. wide for transport, folds in or out easily, pulls with anything that has a hitch, and individual wheels raise and roll over rocks and gopher mounds, It’s a simple design that'll combine three 9-ft. haybine swaths together in one pass working fast with minimum maintenance. We pick up the swath with our Vermeer round baler without zig-zag driv “ 7 ee wee Best & Wor ( ing. I bought one last spring and used it all summer, I have a lot of small odd-shaped fields with rocks and gopher mounds so I really put it to the test. I had some problems with parts of it that were not built of strong enough material. talked to Mr. Kuehn and learned he had made changes since my purchase and he corrected our problems with upgraded replacement parts at no cost to me. ; “Kuehn recently sold his rake design to H&S Manufacturing (P.O. Box 768, Marshfield, Wis. 54449, ph 715 387-3414) because he could not keep up with orders.”

Best Buy
P.H. Bourgeois, Barrhead, Alberta · Vol. 12, No. 6 (1988), p. 12

P.H. Bourgeois, Barrhead, Alberta: His “worst buy” is an older Krause tandem disk. “After 200 or 300 acres with it I have to replace bearings.” Another “worst buy” is a set of Dayton 14-in. tires that were bald at 21,000 kilometers. “I was allowed only $54 warranty.” linate IUYS On the positive side, he’s pleased with his Vermeer Bale Buster round bale feeder which can also be used to spread straw for bedding. “Ill lay down an even layer of straw up to 35 ft. wide, reducing the amount of straw needed for bedding by 50%. When used to feed out hay bales it reduces waste by at least one third compared to feeding free-standing bales.”

Worst Buy
Kenneth V. Grimm, Deep River, Iowa · Vol. 11, No. 6 (1987), p. 12

Kenneth V. Grimm, Deep River, Iowa: “My worst buy is a 1986 Massey Ferguson 656 ‘auto weave’ baler which is the same as Vermeer’s 605). [tlisted for almost $19,000 and has been the biggest disappointment of any equipment!’ ve ever owned. I never had asingle trouble-free day of baling during the first summer of custom work. I spent more time unplugging it and straightening belts than I did baling. Vermeer recalled it and added a self-contained hydraulic system. That had been the only part of the baler that I hadn't had trouble with. They call it the “smart baler” but every ume I get it set to where it will make a decent bale, it seems to lose its smarts. Also, they would not extend the warranty after it was rebuilt. [haye now given up on the auto weave feature and operate this baler manually.”

Best Buy
John Vermeer, Sheldon, Iowa · Vol. 11, No. 5 (1987), p. 13

John Vermeer, Sheldon, Iowa: John names his 750 Super B Energy Miser crop dryer by Beard Mfg. as “best buy”. “Very well built and extremely well engineered. Good dealer service, also.”

Best Buy
Ray Stein, Taylor, No. Dak. · Vol. 11, No. 3 (1987), p. 13

Ray Stein, Taylor, No. Dak.: "We're very pleased with our 605 H Vermeer baler. It really eats the hay. The new pressurized air bags help bales hold their shape well. We also think the bale ejection system is great. There were a few changes the company had to make but they were real good about replacing the things that were wrong. "Another best buy is an Arts Way 425A grinder mixer. This is the most trouble-free machine on our farm. We grind about 4,500 bu. of corn, oats and barley a year. In the last 12 years, all we've done is replace the hammers.”

Best Buy
Sieg Weiss, Decorah, lowa · Vol. 11, No. 3 (1987), p. 13

Sieg Weiss, Decorah, Iowa: "I'm convinced that the Deere 530 round baler will outbale both the 5580 Hesston and the 605F Vermeer that we traded in. It makes a perfect, solid bale every time. We stack bales 3 high in poles sheds and the stacks don't settle, sag or tip over. "On the other hand, the converging wheels we put on weren't worth the bother. They run directly behind the tractor wheels but the rubber saw-type teeth won't pick up much of what the tractor's driven over. After a few hours of operation, the teeth stayed pointed backwards, making them even less effective."

Worst Buy
John Nelson, Brayton, Iowa · Vol. 11, No. 3 (1987), p. 14

Ferguson 285 tractor as "best buy". "It has 38-in. rear wheels for adequate ground clearance to cultivate 2-row tobacco. Starts easily in cold weather, has short turning radius, good weight distribution and excellent fuel economy. Also has good drawbar horsepower, roomy cab and good visibility under the tractor.” John Nelson, Brayton, Iowa: "I had 10 Vermeer balers before this one and had minimal problems with them. But my worst buy was a 605] Vermeer baler. The grease seal fell out of the gearbox, and the bottom broke off of the tailgate cylinder, I had problems with the tailgate coming unlocked while baling and problems getting it locked on sidchills. It also had a broken roller, problems with a roller moving on a shaft and rubbing on the baler, broken shaft in a roller, and numerous broken welds, including on the bar that holds the baler together. The twine arm would bend every time a little hay would stop on the pickup. One light on the monitor wouldn't work, the chain oiler used about 2-gal. of oil a day and the chain tightener wouldn't stay on. After many calls and a couple of trips to the factory, they finally agreed to take the baler back for a price."

Best Buy
Kenneth Burks, Comanche, Tex. · Vol. 11, No. 1 (1987), p. 13

Kenneth Burks, Comanche, Tex.: “T couldn’t keep enough bearings around here for my 605 F Vermeer baler. ran it three years and put countless bearings on it along with two drive sprockets and two drive chains.” He’s pleased with his Deere 503 round baler. “I ran the first one three years and put only two bearings on it. The second one is a year old and we haven't had any troubles.”

Worst Buy
Vern Martens, Ashton, lowa · Vol. 10, No. 6 (1986), p. 14

Vern Martens, Ashton, Iowa: ‘Our Massey Ferguson 530 spinner drum mower bought in 1984, and manufactured by Vermeer Co., is worst buy. Two of the drums were not made correctly. The cutting knives on one drum would hit the knife and other drum opposite. Masssey checked it out and made replacements through Vermeer. This mower will cut anything but it is costly to keep running. I've gone through 7 sets of knives on the drums in three seasons of use. I thought I'd get more for the money. ”

Best Buy
William Ondracek, Max, Minn. · Vol. 7, No. 6 (1983), p. 12

William Ondracek, Max, Minn.: He's pleased with the electric fencer he bought from Hol-Dem Fencers of Minneapolis, Minn. “The model 57 has good power, even with lots of weeds on the line or when the wire is shorted on a nail or post. The battery-powered model 55 can use either 6 or 12-V batteries, dry or wet, and has good power with good battery life before recharging. “Another best buy is my Vermeer 605C big round baler that I bought in 1979 from my Dad and which he bought in 1974. It's been a real good bajer. Dad replaced the belts once and we've both had to replace bearings but that’s normal. The only bad thing I can find is that when you have really light, short hay, it's sometimes hard to get a bale started. “My worst buy is my Versatile hydrostatic 400 swather, with a mounted crimper, that I use for cutting hay. The header is a piece of junk in hay. It’s built so light something is always breaking down, The only good thing about it is the crimper which does a real good job.”

Best Buy
Philip Wilson, Lewisburg, Tenn. · Vol. 7, No. 3 (1983), p. 11

Philip Wilson, Lewisburg, Tenn.: “My best buy would be my 2290 Case tractor. The tractor has more horsepower than its rating. The fuel economy is very good. The cab is comfortable and the hydraulics are superior to any tractor have ever had any experience with, ‘The dealer is also good. “Another good buy is my 605 Vermeer round baler. This machine has given six years of service with only modest repairs in key wear areas. The baler has paid for itself several times and hopefully has several more good vears left.”

Best Buy
Frank Stefka, Comstock, Neb. · Vol. 7, No. 2 (1983), p. 12

Frank Stefka, Comstock, Neb.: I'm glad I took out $500, 50,000-mile insurance. couldn't afford to drive without it," says Frank, unhappy with his 1980 Ford 4-wheel drive, % ton pickup. “It's on its third transmission in less than 40,000 miles and that's going bad, too. It has had five heater switches and you still have to kick it to start the blower. I also had “Tt’s on its third transmission in less than 40,000 miles.” trouble with the air conditioner and the front wheels often won't lock in when you need them. The dealer is good but the company didn’t have the farmer or rancher in mind when this pickup was built.” On the plus side, “I've had Vermeer balers since 1976, including ‘D’, ‘G’ and ‘F’ models. They've been the most trouble-free machines I've ever had on the ranch. I bale 2,500 to 3,000 bales a year and have found that the belts cause no problems and are much gentler with alfalfa than other types of balers. The Vermeer Company stands behind their products 100%. I was so pleased with the company that, when I had a chance to become a farmer dealer for them, I jumped at the opportunity.”

Best Buy
Jack Bonnette, Marietta, Ohio · Vol. 7, No. 1 (1983), p. 11

Jack Bonnette, Marietta, Ohio: “We looked closely at several round balers and were most impressed with the quality and ruggedness of this baler,” says Jack, about his Vermeer 504G baler. ‘‘When we first baled with the machine we found it was simple to handle and it operated as if we had used it before. Our hay is of excellent quality and our cows eat all of it. “Another good buy was our Deere 1207 mower-conditioner. We used it last summer and have only had to sharpen the sickle so far. Runs extremely quiet and is easily transported from one farm to another.” On the negative side, Jack's disappointed with replacement parts for his International tractor. “We spenta large sum of money and down time to install a new torque amplifier system in our International and it lasted approximately 50 hrs. before going out because of bad bearings.

Best Buy
Marvin Lackman, Denison, lowa · Vol. 6, No. 2 (1982), p. 13

Marvin Lackman, Denison, lowa: He likes his model F Vermeer big round baler, “It makes a much better bale and operates much easier than a baler I had of another brand.”

Best Buy
Robin Robinson, Lovelady, Tex · Vol. 5, No. 6 (1981), p. 10

Robin Robinson, Lovelady, Tex: Robin likes his 605 F Vermeer round baler. “This baler has been very dependable and easy to operate. I've had one bearing go out in more than 2,000 rolls of hay. It puts up a consistently tight bale.” Robin's disappointed, however, with his Caraway V-type front end rake. “We purchased the rake from a local dealer and were told it would work well on any tractor in any type of hay. We found thé rake caused all of our tractors to overheat, including a 100 hp John Deere. Secondly, it would not rake our thick hay because the hay built up in front of the tractor and made a great mounded windrow that our trailing baler could not begin to handle. ‘When we went to the rake dealer for some solutions to our problems, there were none. He told us that we were the only ones having the overheating problem, which was the problem we were most upset by. We tried to trade the rake in to the dealer where we purchased it. He wanted to charge us $700 for raking about 100 rolls of hay. None of the other dealers in town even wanted to consider a trade with us, including the Vicon dealer who supplies the basic rake to Caraway. They wanted $3,000 difference between our two-month-old rake and their $5,600 rake.”

Best Buy
Terry Frommelt, Guttenberg, Iowa · Vol. 5, No. 6 (1981), p. 11

Terry Frommelt, Guttenberg, Iowa: ‘This is a super baler,” reports Terry about his Vermeer 605F round baler. ‘Most new equipment requires a percentage of warranty work but the only repair work I've done after custom-baling 1,500 bales is on one sealed bearing, a couple bolts in the pickup bar and I replaced three belts. In the first 1,000 bales, I didn't have a single problem.” He's not satisfied, however, with his Duracraft 6-in. bench vise." When you putan item in one side of the vise it does not tighten evenly in the jaws. When the jaws are tightened by hand only, using no extra leverage on the handle, the screw in the vise will jump a thread when it is almost tight.” Gilles Dehoog, Jr., Lynden, Wash.: “My ‘best buy’ is a model 698 Weed Eater,” says Gilles. “The gas motor has lots of power for its size. With the nylon line you can trim around buildings, fence lines or just anywhere. With the brush blade I've cut trees two inches in diameter. “Il also like my John Deere 2640 tractor. It’s small enough to scrape around the barn lot and, putting out 80 horsepower, it’s just right for field work. “My brother and I work together and another good buy is the John Deere 4440 he bought this spring. It's twice as much tractor as the 3020 (1968) he traded in but cost five times the $8,000 price our dad paid for the 3020. Dad, at 73 years of age, grew up with horses and it usually takes hima year before he tries out a new piece of equipment, but not this one. We had the 4440 only one week when he had to try it out.”

Worst Buy
Curtis Wegner, Paynesville, Minn · Vol. 5, No. 4 (1981), p. 12

Curtis Wegner, Paynesville, Minn: He's happy with his Case 2290 and 990 tractors. ‘I’m having some hydraulic charge pump trouble on the 2290 but the dealer has given good service. The 990 has been good with no trouble except for a fuel leak in the return line which the dealer took care of right away. Real pleased with these tractors and the service." E. Scott Woodard, Jr., Ringgold, La.: ‘We've never had this kind of service on farm equipment or, for that matter, anything,’’ says Scott, pleased with the dealer followup on his Massey Ferguson 2705 tractor. “Other than an imperfection in the casting of the front axle, we're very satisfied.” His “worst buy’? nomination goes to his Gilmore-Tatge portable holding bin. “The cone sheets wouldn't fit together, Just a son of a gun to put together. It took three men four days to assemble the 9-ft. dia. 500 bushel portable bin.” Jim Jirava, Ogema, Minn,: ‘This baler has never baled 15 bales at any one time since it was new,"' Jim says about his Vermeer 605 Super C round baler. ‘The belts turn over every 4 to 5 bales, the slip clutch isn’t big enough for the machine, and any little gob of hay will plug it.” His ‘best buys" include an International 800 hinge plow and his 6-in. Vac-U-Vator pneumatic grain mover. “I've put just $12 into this plow in three years of plowing. Works well under any condition and follows varying ground contours. The Vac-UVator moves grain with ease and a minimum of trouble. Dealer service is good.”

Best Buy
Herbert Condalary, Mt. Hermon, La · Vol. 5, No. 3 (1981), p. 11

Herbert Condalary, Mt. Hermon, La: “I've had this truck about one year. The drive train leaks, the engine has no power, the material in the body is flimsy and so is the workmanship. The only good thing is that it rides and drives good, and the dealer gives good service,” says Herbert about his 1980 Ford F-250 4x4 3/4 ton pickup. He's pleased, though, with his Vermeer model E£ hay baler. “This is my third Vermeer baler and, while they've all given great service, this model is the best Vermeer has produced. It's the best baler I've ever used in rye grass hay in our humid southern springs, I've run this baler all afternoon without a single clog-up. After nearly 10 months and 1,000 bales, haven't had to replace a single part.’

Best Buy
Steven Hickenbottom, Fairfield, Iowa · Vol. 4, No. 6 (1980), p. 11

Steven Hickenbottom, Fairfield, Iowa: “You can mow anything with it as fast as you can drive and stay on “You can mow anything with it as fast as you can drive.” the tractor,"’ Steven told FARM SHOW about his Vicon disc mower. “You can even go to the field and mow at 6 a.m, in heavy dew, “Another good buy is our 504F Vermeer big round baler. Makes the best bale of hay I've ever seen. No problems. “The worst product I've bought lately is the Walsh fiberglass ‘skinny minny’ spray tank. I’ve had a pair of them three years and although the size works well on the tractor I've got them mounted on, one tank has just about cracked to pieces. They both leak and all 1 do when spraying in the spring is patch them up,” “Along with the tanks,’ he adds, “the Ace centrifugal pump that came with the outfit lasted about 100 acres. I went through three more pumps in about six hours. The Ace pump just kept throwing the belts off. We found out that the machining on the pump was off, but the company made no adjustment except on the first pump.”

Best Buy
L.D. Murphy, Plainville, Kan · Vol. 4, No. 6 (1980), p. 13

L.D. Murphy, Plainville, Kan: He's unhappy with his Vermeer 605-F baler. “I had a 605 Super C baler for three years and had no trouble but the 605-F had light bearings and shafts that went out. The pickup is a joke, with only four rows of teeth, Won't pick up light windrows; in heavy windrows, it breaks out teeth, bends teeth bars, and loosens bolts out of teeth bars. New balers now have five rows of teeth, but the dealer doesn't want to trade because no one wants this baler’s four rows of teeth.” Murphy's also had trouble with his Sunflower 15-ft. undercutter, ‘‘We have adjusted and readjusted and still the shanks won't go the same depth inthe ground. Won't stay inthe ground if it is only a little hard.”’ He's been pleased with his 2280 John Deere swather. ‘Have had no trouble with it, replacing very few sections. “A pair of 4240 Deere tractors, both equipped with Deere 158 loaders, have also been best buys. Good power for their size and the powershift works excellent. Have only had two hydraulic oil leaks and the dealer fixed them the day they happened. Deere loaders are built tough and are easy to take off and put back on.”

Best Buy
Thomas Pearson, Hudson, Iowa · Vol. 4, No. 4 (1980), p. 11

Thomas Pearson, Hudson, Iowa: “We had only one malfunction all season — a small valve in the diesel pump — and that was replaced quickly by the dealer after a call,” Thomas reports about his ‘‘best buy”’ Deere 8820 combine with 20-ft. platform and 8-row corn head. ‘A high capacity and efficient machine, both in soybeans and 170 bu. corn." He's not happy, however, with his Vermeer 900 3-pt. hitch backhoe. “Basically, it's a fine piece of equipment, but will not function using the tractor hydraulic system, as it is sold to do. It doesn't have any digging power, swinging too fast and jerking the tractor. We tried different tractors with the same results.”

Best Buy
John Nelson, Brayton, Iowa · Vol. 4, No. 3 (1980), p. 11

John Nelson, Brayton, Iowa: “‘Had virtually no maintenance in the first 3,000 bales. The only repairs were one bearing. two belt splices and some teeth in the pickup attachment. The combination hydraulic and spring tension makes making tight bales easy. Extremely well-built,” says John of his ‘‘best buy" Vermeer 605 F big round baler.

Best Buy
Charles T. Cleaver, Mt. Pleasant, Ohio · Vol. 4, No. 3 (1980), p. 11

Charles T. Cleaver, Mt. Pleasant, Ohio: “We ordered the machine in Dec. 1977 to be delivered in time for the 1978 hay season, but our dealer didn't receive it until mid-June, 1978," says Charles, about his Vermeer 504-F baler. ‘Service was good but it was a new model that still had bugs in it. Our main difficulty was getting bales out of the machine. We even had to try pulling them out with another tractor. It turned out that the frame of the machine was narrower at the back gate than in the center, where the bales were made, so they wouldn't fall out. Our dealer was told from the factory to put a big jack in the back and spread the back of the machine and this seemed to solve the problem. Two bearings went bad on an idler roller in the first 300 bales of operation. The 1979 season went real well after they worked on it." His nomination for “best buy” goes to Splice-It fence repair tool. “With rising fence wire costs this tool is a big help. You can use up short pieces of wire for patches where before we had to make loops in the wire ends. Makes tighter repairs easier.”’

Best Buy
Daniel H. Bender, Harrisonburg, Va · Vol. 4, No. 3 (1980), p. 12

Daniel H. Bender, Harrisonburg, Va: ‘Most of their ‘name brand’ products can be bought from local sources for less dollars,"’ says Daniel who's disappointed with Farmers Purchasing Group, Topeka, Kan. He's also disappointed with his “Flo-mor bottom grain unloader. It's a good idea but the manufacturing was lousy. Had to re-drill holes, weld collars that didn’t line up, and the chain brackets were incorrectly attached. Their distributor in Pennsyl“They had the operator in mind when they built this machine.” vania could have cared less. But it does work.” Heading his “best buy" list is his Vermeer model F baler. “Makes a beautiful, tight, weather resistant bale. Well-built and has required little maintenance through the first 2,000 bales.” He's also happy with his John Deere 6600 combine. ‘They had the operator in mind when they built this machine. Convenient to service, and easy to adjust. Overall, it's mechanically well-built and smooth running.”

Best Buy
John C. Carrington, Swansea, S.C · Vol. 4, No. 2 (1980), p. 14

John C. Carrington, Swansea, S.C: “This is the only piece of equipment] ever bought with only a brochure to go by,” reports John about his *‘best buy” Tyler LFS-S stainless steel lime and fertilizer spreader. “This is one spreader that is built for easy service and long life. Spreads two bushels of wheat or one ton of lime per acre equally well. looked at three other brands and the Tyler was the bestbuilt and least expensive of them all.” John's also happy with his “Vermeer 605F round baler. Only had about 3 hrs. of down time in baling 2500 tons of hay last year. It will bale any hay dry enough to safely bale. Starts the roll very well and makes uniform, tight bales. A great improvement over any previous round baler.”’ caicmapenenunwe Cio side, John is disappointed with the quality of American made tires. “'l believe that, since the government adopted load range standards, tire companies have used government minimum requirements as their maximum performance standards. Tire quality. as a result, has been reduced," says John, noting that he’s upset with all Américan-made . tires, and trailer tires in particular. “We bought a three axle gooseneck equipment trailer five years ago with vight ply Seiberling tires on it. Those tires have worn out over the past two years and have been replaced by Seiberling, Hercules and Farm Bureau 8-ply or load range “D" tires. I've had blowouts with all three brands.”

Best Buy
Mark Germann, Morganville, Kan · Vol. 3, No. 2 (1979), p. 10

Mark Germann, Morganville, Kan: He nominates Prowl herbicide as his worst buy. “We applied it according to directions and had plenty of moisture to activate it but itran out of power before the crop even got started. Weeds came through it like wildfire and we found Treflan worked better by far.’’ On the positive side, Mark nominates his Vermeer 605F Big Round Baler as a best buy. “It's the best baler I've ever had, even if itisa little tricky to learn to run and get uniform bales. Makes nice hard bales in most crops. Bearings are easy to get to and all one size. The hydraulics make it easy to change tension on the belts. Its faults are that it's hard to see the bale in the chamber, and the endgate opens too fast,””

Worst Buy
Bill Ogier, Alpena, Ark · Vol. 3, No. 1 (1979), p. 14

Bill Ogier, Alpena, Ark: ‘It never has run right. No power — kinda lopes down the road and feels like you're riding a horse. Just after the warranty was up, the front wheel bearings went out. About 1000 miles later, the rear spring broke. No dealer response,”’ says Bill of his ‘worst buy” Ford LTD car witha 400 engine. Bill adds that his Vermeer round baler (Model 504) “is one of the simpliest built and easiest to operate machines I've ever run".

Best Buy
Lee Phelphs, Schoolcraft, Mich · Vol. 1, No. 1 (1977), p. 27

Lee Phelphs, Schoolcraft, Mich: Lee Phelphs, Schoolcraft, Mich. ‘‘I bought the 44 in. system instead of 6% in. — much cheaper and it did the job.” Vermeer 504C big round baler: Works real good. It’s a very easy, convenient way to pul up hay for me, and ‘Holds more than the manufacturer rates it.”’ also easy to feed the way I'm set up,” says Danny Turner, Orangeville, Idaho, Dickey-john planter monitor: ‘In years past, we had trouble with skip rows which, in turn, lowered our production,”’ reports Gary Weaks, Silverton, Texas. He solved the problem with the new monitor. Weaks isn't happy, however, with a Nile 35 grain moisture tester which he purchased: “We made a test and, to our surprise, had corn that tested “Tt’s trouble free. Did the job they said it would.” 18%. So, happily we commenced harvest only to find, with the first return truck, that when our tester said 18% it might be 22%. Or, if it said 22%, it might be 18%. It would never be closer than 2 points. Moisture is

Vermeer 605 J round baler

7 Best Buys1 Worst Buy
Best Buy
Chris Kliment, Prague, Neb. · Vol. 45, No. 2 (2021), p. 15

Chris is the satisfied owner of an early 1990’s Vermeer 605 J round baler. “It does a really nice job for an old baler. A spring broke and a couple bearings were replaced, but that’s just routine maintenance.”

Worst Buy
Dean McDaniel, Beaver, Okla. · Vol. 25, No. 2 (2001), p. 15

“My New Holland 688 round baler does a great job of starting bales and makes them nice and tight. It also does a good job ejecting bales.

“My Vermeer 605J round baler is my worst buy. I bought it to put net wrap on my bales but found that it did a poor job. I could put one good wrap on, but then the next bale would have too much wrap on one side and not enough on the other. I finally traded it in for a New Holland.”

Best Buy
John D. Bata, Adams, N. Dak. · Vol. 20, No. 4 (1996), p. 14

John says his 1991 Vermeer 605J baler makes big, tight bales with few problems and is his “best buy”. “We’ve owned two other Vermeer balers, a 605C and a 605G, but this is the best one yet.”

Best Buy
David J. Leiker, Hays, Kan. · Vol. 17, No. 3 (1993), p. 16

David J. Leiker, Hays, Kan.: David’s had good luck with his 1990 Vermeer 605J baler. “We owned a 605C model for 13 years before we updated to this model. It has made 8,000 bales with virtually no downtime. “Our 1991 Ford TW25 front wheel assist tractor is a best buy. It’s dependable, easy to operate, and comfortable. “Our 1992 Westendorf TA 46 loader is our worst buy. We couldn't use the loader without modifying the mounting brackets. Our dealer helped us every step of the way. However, when we called the factory we got the runaround. The first time we used it oil leaked all over the hood because the hoses weren’t tight. After using it one year, the bucket is bent up on the bottom due to frozen manure because it’s built too light. One plus is that it’s a snap to mount and dismount.”

Best Buy
Dave Anderson, Postville, Iowa · Vol. 16, No. 3 (1992), p. 14

Dave Anderson, Postville, Iowa: “My best buy is my 1989 Vermeer 605 J round baler, I do custom work and have used it to make more than 10,000 bales. I also use it to make cornstalk bales every year. The only repairs have been fora few bearings, chains, and sprockets, and last spring I replaced aboutadozen of the rubber-mounted pickup teeth.”

Best Buy
Oliver Oswald, Eureka, S.Dak. · Vol. 12, No. 5 (1988), p. 12

Oliver Oswald, Eureka, S.Dak.: “It’s the best swather I've ever used,” says Oliver, happy with his new 6000 Case-IH 21ft. grain swather equipped with a double swath mechanism. “We’ ve puton 300 hours with few problems. However, the swath shifting mechanism should shift faster. A bigger hydraulic cylinder would alleviate the problem.” He also likes his Vermeer 605J Auto Weave baler. “If we had to replace it, we’d buy the same model again. It’s a well built machine, as is our Case-IH 1460 combine which has needed little maintenance.”

Best Buy
Steve Ogden, Lexington, Kty. · Vol. 11, No. 3 (1987), p. 12

Steve Ogden, Lexington, Kty.: "I nominate my Vermeer 605J round baler with VCS-3 monitor and autoweave system as best buy. After baling 550 bales with it in 1986, it still amazes me and everyone who watches it in operation. Its electro-hydraulic steering system and monitor is far ahead of all other brands, There's no need to constantly look back or watch the monitor. The bales are virtually perfect every time and rolled tighter than bales from other makes I considered. It consistently beats the Deere 530 baler by 200-Ibs per bale. The standard haysaver wheels work great and lifts with the pick-up when it's raised to the transport position.”

Best Buy
Louis Riou, Arborfield, Sask. · Vol. 11, No. 3 (1987), p. 12

"I nominate my Vermeer 605J round baler with VCS-3 monitor and autoweave system as best buy. After baling 550 bales with it in 1986, it still amazes me and everyone who watches it in operation. Its electro-hydraulic steering system and monitor is far ahead of all other brands, There's no need to constantly look back or watch the monitor. The bales are virtually perfect every time and rolled tighter than bales from other makes I considered. It consistently beats the Deere 530 baler by 200-Ibs per bale. The standard haysaver wheels work great and lifts with the pick-up when it's raised to the transport position.” Louis Riou, Arborfield, Sask.: "Last year I bought a new 8-hp. TroyBilt rotary tiller with which I'm very pleased. It's ruggedly built and has a good warranty. The only drawback is that it doesn't have a differential which makes it hard tuming comers."

Vermeer 504 round baler

3 Best Buys1 Worst Buy
Best Buy
John H. Ruehter, Pleasant Hill, Mo. · Vol. 30, No. 3 (2006), p. 13

“My 2003 Case IH MX tractor has been trouble-free. It has a lot of power and is comfortable to operate. The cab is nice and quiet with good controls.

“My Vermeer 504 round baler makes a nice, tight bale. Bale density is the same from start to finish, so you get more hay per bale.”

Worst Buy
John K. Kilian, Norlina, N.C. · Vol. 26, No. 6 (2002), p. 14

“I haven’t had any problems with my Vermeer 504 round baler or my Krone disc mower.

“My Deere 6400 tractor is powered by a 4-cyl. engine that’s very powerful. This tractor has 1,500 hours on it with no problems.

“The engine on my Deere 4020 tractor has about 9,000 hours on it but has never been overhauled. It’s a great loader tractor.

“My Isuzu Lil Pup pickup is tough as nails. It has 150,000 miles on it but has required no major repairs.”

Best Buy
W. Gene Davis, Broadway, Va. · Vol. 21, No. 1 (1997), p. 15

“My 1996Vermeer 504 I round baler makes nice, tight bales that are easy to load and haul on the highway. I’ve used it to make about 1,000 bales with only minor problems that were easily corrected.”

Best Buy
Ed Obert, Palmyra, Mo. · Vol. 18, No. 1 (1994), p. 16

Ed Obert, Palmyra, Mo.: Ed’s the satisfied owner of a 1993 Vermeer 504 silage baler. “It really saved us last summer because of all the rain we had. I was able to cut my hay and bale it two hours later. Otherwise, I’d have had a lot of spoiled hay. We baled for several local farmers, saving their crops.”

Vermeer 605-G round baler

4 Best Buys0 Worst Buys
Best Buy
Loren Cumming, Mapleton, Minn. · Vol. 14, No. 5 (1990), p. 13

Loren Cumming, Mapleton, Minn.: Loren says his Vermeer 605-G round baler is a “best buy”, “It's built to stand up to many years of use under all conditions.”

Best Buy
James Rocheleau, Barton, N.D. · Vol. 11, No. 5 (1987), p. 13

James Rocheleau, Barton, N.D.: “My Wilrich 8-18 hinge frame plow plows beautifully and is strong, but it’s next to impossible to change depth after changing lays. Also, when I get into mud, I can’t raise it slightly to get through without wrecking the rear furrow. Thus the next furrow is also thrown out of whack. The furrow wheel rubs sideways against the furrow wall constantly. We can't seem to adjust it so the wheel will run straight.” James names his 1985 Dual 3100 Quick Tach loader as “best buy”. “It’s a strong loader with cylinders that don’t loosen up too bad on the ends. Overall, it’s a well designed product built to last. But, I didn't like their flimsy grapple fork, so I built my own. Also, their mounts stick the loader out too far, so I built some that mount it tighter to the tractor front end,” Victor Jim Dubbert, Laddonia, Mo.: “Our best buy in the last year has been asetof skid plates from Poly Tech Industries, Monticello, Ga. for under the combine header They help keep dirt or mud from getting in with your grain, Wealso like our 2594 Case tractor. It’s trouble-free and has plenty of power.” Patrick Matthews, White Oak, S. Car.: “A 1986 Vermeer 605-G hay baler is our best buy. It’s much improved over previous balers we’ ve used, It starts making bales quickly and gives more even distribu)/- <7 FARM SHOW « 13 Best And Wors (Continued from preceding page, tion of hay because of the ‘open throat’ — design. It's far easier to unclog damp hay out of than earlier Vermeers, However, the method of wrapping twine around the bale should be improved.”

Best Buy
Ron Kramer, Earling, Iowa · Vol. 10, No. 6 (1986), p. 13

Ron Kramer, Earling, Iowa: ‘The Thunder Gun power washer was advertised to hook up to your own air compressor and water hydrant to give you a cheap power washer with lots of pressure. It was only a plastic pipe that you could blow water through. “My best buy is a 1984 Vermeer 605-G round baler. It’s baled over 5,000 bales in the last three years with only normal maintenance, Very dependable and easy to operate.’ Best And Wo (Continued from preceding page) $6,000 price of the hitch. Too bad they discontinued making this hitch.” James F. Slater, Jeromesville, Ohio: He's happy with his 385 International tractor. ‘It works great. Does the job just the way it should.”

Best Buy
Richard Alexander, Washington, Ohio · Vol. 9, No. 2 (1985), p. 13

Richard Alexander, Washington, Ohio: 'My best buy was a subscrip- tion to FARM SHOW. | look forward to each issue and then give it to my neighbor." Jerome Delvo, Langdon, N. Dak.: "Baling hay with my Vermeer 605G is a pleasure. It seems to work well with any type of hay. We baled 735 big bales of hay and straw without any problems or breakdowns." Arthur Harms, Pine Bluffs, Wyo.: Arthur nominates his Homelite 240 chainsaw as "best buy". "I cut a lot of wood with it last fall and didn't have any problems. Starts easy in any kind of weather." Fred Welch, Wallaceburg, Ont.: "It has lots of power, gets 25 mpg and starts well in cold weather," says Fred, pleased with his Ford 250 HD diesel pickup. "Another one of my best buys is my 2-85 White tractor. | bought it nine years ago and it's still in super work- ing condition."

Vermeer 605H round baler

4 Best Buys0 Worst Buys
Best Buy
Marcus A. Evers, Eugene, Mo. · Vol. 27, No. 3 (2003), p. 13

Over the years Marcus has had a lot of success with Allis Chalmers equipment. “We’re still using our 1936 Allis Chalmers WC tractor equipped with 12-ply road grader tires for bush hogging and raking hay. We use our 1951 Allis Chalmers WD tractor for mowing and also for making hay with our 1968 Allis Chalmers 303 square baler. We use our 1974 Allis Chalmers 200 tractor for heavy work and for making hay with our Vermeer 605H round baler. We use our 1968 Allis Chalmers I600 backhoe for handling big bales and dirt work.”

Best Buy
Russell Parris, Pleasant Hill, Mo. · Vol. 17, No. 5 (1993), p. 16

Russell Parris, Pleasant Hill, Mo.: “My Vermeer 605-H round baler is my best buy. It's very reliable. However, it should have a double drive chain instead ofa single one so the chain and sprockets would last longer. Also, the baler does a poor job in wet hay.”

Best Buy
Doug Allison, Corning, Iowa · Vol. 17, No. 5 (1993), p. 16

Doug Allison, Corning, Iowa: Doug's the satisfied owner of a 1983 Vermeer 605H round baler. “It makes nice solid bales. The six-bar pickup is equipped with rubbermounted teeth and does a good job picking up hay. I don’t know how they could improve this baler. It bales tough hay with no problems. The only limitation is thatin light hay or straw I sometimes have trouble starting the bale.”

Best Buy
Elton Zimmerman, Buffalo, Mo. · Vol. 8, No. 4 (1984), p. 11

Elton Zimmerman, Buffalo, Mo.: He likes his Vermeer 605H round baler. ‘It makes tight, square-edged bales up to 2,000 Ibs. with much less spoilage than other balers.”

Vermeer 504-I round baler

3 Best Buys0 Worst Buys
Best Buy
Doyal Wynn, Rutledge, Tenn. · Vol. 25, No. 2 (2001), p. 16

“My 1999 Vermeer 504-I round baler makes good, tight bales that are easy to start.”

Best Buy
David Rudy, Warwick, N.Y. · Vol. 22, No. 5 (1998), p. 15

“I’m well pleased with my 1997 Vermeer 504I round baler. It does a good job of baling all types of hay, from wet silage bales to thick, fluffy dry hay. It’s a remarkable baler. I’d recommend it to anyone.”

Best Buy
Dan Haberer, Russell, Kan. · Vol. 21, No. 4 (1997), p. 16

“My Westfield electric/hydraulic drill fill auger is well made and an excellent product.

“My 1992 Deere 4255 is a super tractor. Why anyone would want more in a tractor is a mystery to me.

“My 1993 Vermeer 504I round baler is easy to operate and virtually trouble-free. It does an excellent job.”

Vermeer 504 Super round baler

3 Best Buys0 Worst Buys
Best Buy
Rex Hollar, Scranton, Kan. · Vol. 34, No. 2 (2010), p. 14

Rex is pleased with his 2007 Vermeer TM 700 disc mower and 2008 Vermeer WR 22 wheel rake. “We had to make some changes to our hay operation so I turned to my Vermeer dealer. After using the disc mower for a month I wished we had bought it sooner. Then getting the wheel rake just made it a sweeter deal for our big baler. These machines have been reliable and are real time savers.

“Over the years we’ve used our Vermeer 504 Super I round baler to make several thousand bales, and it has required only routine maintenance. We take the baler back to the dealer every winter to have it checked over, which lets us keep going without having to stop for repairs during the busy hay season.”

Best Buy
Tim Schultz, Clintonville, Wis. · Vol. 16, No. 3 (1992), p. 13

Tim Schultz, Clintonville, Wis.: “My best buy of all time is my silage bagging equipment. ( /y/ .2?. FARM CHOW - 42 Best & W ( I started with a Silopress XPIII (Silopress, 1915 Floyd Blvd., Box 988, Sioux City, Iowa 51102) and now also use a Uni-press. Both systems make it easy to make excellent quality feed for my 65 dairy cows. They’ve allowed me to increase production and profit per acre from forage while reducing the amount! spend on purchased feed. I had been using cement top-unloading silos and Harvestores, but now they stand empty and unused - I can’t afford to use them. “My 1990 KnightReel Augie 2375 TMR pull-type mixer is also a best buy. It lets me feed all my milk cows once a day in about 45 min, and has allowed me to maintain a 20,000-Ib. herd average while cutting purchased feed costs by 40 to 50%. The TMR mixer and silage bagging systems together have greatly increased my profitability. I'll never go back to my old system. “My 1991 Vermeer 504 Super I baler performed just like I expected and makes nice tight bales. The dealer spent plenty of time with me to make sure I knew how to use it I'm completely satisfied. “My Landoll Tilloll implement provides true one-pass spring tillage. Really saves time and fuel. “My Deere 1460 disc mower-conditioner is a best buy. My wife can use it to cut hay at 7 to 8 mph without plugging it up. I’ve tried my hardest to plug it up, but I can’t. If it lasts as long as it’s supposed to, it'll eam ‘best buy’ status. “My worst buy was a 1990 Case-IH Maxxum 5120 tractor. It caused me lots of grief before I traded it in on a Deere. In “If it lasts as long as it's supposed to, it'll earn 'best buy' status.” fairness to Case-IH, it was one of the first models built and I understand that most of my problems have been corrected in later models or by recalls. However, I still feel it has too much electronic equipment for a farm tractor. The 3-pt. took too long to lower for a job like cultivating and trim pieces kept falling off. In cold weather the engine would start fine, but the tractor wouldn't move. The clutch works off electric switches somehow. The dealer bent over backwards to solve the problem but had no luck. I’d recommend the dealer to anyone, but a Maxxum only to my enemies,”

Best Buy
Robert Francis, Pearisburg, Va. · Vol. 15, No. 3 (1991), p. 13

Robert Francis, Pearisburg, Va.: “This is truly the Cadillac of round balers,” says Robert, pleased with his 1990 Vermeer 504 Super round baler. “The soft start springs eliminate any problems whatsoever with “This is truly the Cadillac of round balers.” getting the bale core to start rolling. The double arm twine wrap system cuts tying time almost in half.”

Vermeer 605

2 Best Buys1 Worst Buy
Best Buy
Orlin Diesen, Wannaska, Minn. · Vol. 10, No. 3 (1986), p. 13

Orlin Diesen, Wannaska, Minn.: He's disappointed with his Vermeer 605 G baler. “It wouldn't bale dry hay or long timothy hay. Pulled twice as hard as the same size Hesston. “In three years my ‘best buy’ Hesston 1500 baler has never been down for more than normal maintenance, and to put on pickup teeth and relace the belts. “Another good buy is our 1980 Chevrolet Citation. We bought it with 80,000 miles on it. It has now 140,000 miles on it and all we've spent is about $275 for repairs.”

Worst Buy
David C. Prause, China Spring, Tex. · Vol. 9, No. 5 (1985), p. 14

David C. Prause, China Spring, Tex.: "I bought a 13-shank Mohawk chisel plow 21 years ago. It's a very good machine. I also like my Vermeer 605 Super F round baler. Never a problem — not even broken teeth." He lists his 1977 150 Ford Super Cab as "worst buy". "It had 70,000 miles before I got it completely re- built and running. Good dealer, just a junk truck."

Best Buy
Jim Brixey, Casa, Ariz. · Vol. 8, No. 2 (1984), p. 10

Jim Brixey, Casa, Ariz.: He likes his Vermeer 605 round baler. “It’s American-made and produces a tight uniform bale. Also like the fact that it has standard-size bolts. It's been trouble-free.”

Vermeer 605M round baler may

2 Best Buys1 Worst Buy
Worst Buy
James Konechne, Kimball, S. Dak. · Vol. 36, No. 3 (2012), p. 14

“I’ve used several different disks in my life but this is the best ever,” says James about his Case IH RXM 340 tandem disk. “Depth adjustment is a simple matter of turning a crank. The implement works at the same depth all across the field.

“My Silencer hydraulic chute with overhead scale makes working cattle a much easier job (ph 308 536-2369; www.silencerchutes.com).

“My 2008 Vermeer 605M round baler may be the heaviest baler ever built, but the bearings on it were junk. We could hardly go to the field without a bearing going out. We finally traded it for a different model.”

Best Buy
Harold David Rupard, Winchester, Ky. · Vol. 35, No. 3 (2011), p. 13

Harold nominates his 2008 Massey Ferguson 5465 4-WD 100 hp tractor with cab as his “best buy”. “It has plenty of power and the 4-WD works great. I’ve put about 2,000 hours on it with no problems. I use it to pull a Vermeer 605M round baler, which is also a best buy.”

Best Buy
Donald B. Hanko, Cazenovia, Wis. · Vol. 30, No. 6 (2006), p. 12

Donald’s the satisfied owner of a 2005 Vermeer 605M round baler. “This baler is built stronger than any baler I’ve ever used. The drum platform that the bale rolls on does more to turn the bale than the rollers in other balers, which relieves stress on the belts and results in less leaf loss. It’s equipped with a unique net wrap system that gets more bales wrapped per roll than other balers. The company used bigger shafts and bearings in critical areas. The baler has a big intake capacity and can make a 2,400-lb. bale. It makes baling hay a much faster job.”

Vermeer Rebel 5500 round baler

3 Best Buys0 Worst Buys
Best Buy
Wayne Tankersley, Bardwell, Ky. · Vol. 29, No. 1 (2005), p. 14

“I’m very happy with our Vermeer Rebel 5500 round baler. I use a 1976 IH 574 52 hp tractor to pull it. It’s also a best buy.”

Best Buy
Marvin Edevold, Bagley, Minn. · Vol. 27, No. 4 (2003), p. 15

“Our Vermeer Rebel 5500 baler works great and is reasonably priced.”

Best Buy
Barduell, Ky. · Vol. 25, No. 4 (2001), p. 15

“We’re well pleased with our new Vermeer Rebel 5500 round baler. We bought it after using a Gehl model for 23 years. We also bought a new Vermeer wheel rake. Both machines do a great job.

“Our 1992 Chevrolet Caprice car equipped with a small V-8-liter engine is a best buy. It gets more than 30 miles per gallon on trips and drives great.

“The worst buy we ever made was a Howse 7-ft. pull-type mower. The blade broke the first year while we were mowing clean, light weeds. Then the second year the whole bottom section that holds the blades broke. The company wouldn’t do anything to help.”

Vermeer round baler

3 Best Buys0 Worst Buys
Best Buy
Donald Miller, Dongola, Ill. · Vol. 31, No. 6 (2007), p. 15

“My 2006 Vermeer round baler has been trouble-free.

“My New Holland disc mower has also been trouble-free. This is my second New Holland disc mower. I used the other one for 15 years and it required only routine maintenance.”

Best Buy
Ray Johnson, Trail City, S. Dak. · Vol. 26, No. 2 (2002), p. 16

“My Vermeer baler is a best buy. This is my second one and both of them have worked great. A bearing goes out once in a while, but I haven’t had any major problems with it.”

Best Buy
Don Scharff, Hartney, Manitoba · Vol. 22, No. 2 (1998), p. 15

“My 1975 Vermeer round baler is my best buy. It was almost trouble-free and is still being used by another owner. I used it to make about 2,000 bales a year when I had it. “My 1996 worst buy is my Cannon BJC 4100 printer. It quit working last June after it had printed only about 80 pages. It has a defective print head which the company won’t replace.”

Vermeer 504G round baler

2 Best Buys0 Worst Buys
Best Buy
Carlton P. Christopher, Hopewell, Penn. · Vol. 35, No. 6 (2011), p. 15

“Several years ago we bought a used Vermeer 504G round baler. From the get-go this baler required too much power, and the bale would jam in the starting chamber. We finally solved the problem by modifying the drive sprocket to slow it down. Now the baler works fine.”

Best Buy
Gerald R. Keith, Leesville, Tex. · Vol. 8, No. 6 (1984), p. 12

Gerald R. Keith, Leesville, Tex.: ‘I only used this grinder a few minutes at a time but, after the second job, it started slinging grease from the gearbox. Before the first grinding disc was one-fourth worn, the motor suddenly sputtered and quit,’’ says Gerald, upset with his “worst buy" Wen 1501 7-in. portable grinder. On the positive side, he names his 1984 Deutz tractor as ‘‘best buy”. “I looked at most other makes and this tractor has the quietest cab in the 4-cyl. range and seems to do more with fewer automatic ‘‘gadgets” than others. I’m continually amazed at the power and traction it has for an 84 hp. tractor. No problems after the initial break-in period. “Also on the best buy side, nominate my Vermeer 504G round baler. It makes a tight, good-looking round bale that keeps its shape very well, operating at 540 or 1,000 rpm’s, I especially like the efficient electric twine tie and its clean job picking up hay. The only drawback is the picker teeth. Balers should not be allowed to leave the factory without rubber mounted picker teeth. The baler breaks regular teeth like crazy and the new teeth used for replacement won't stay tight. However, once we replaced them with rubber-mounted teeth we’ve never broken one. “Another best buy is our Farmhand wheel rake, Since buying it new in 1979, we've never broken a single rubber-mounted rake tooth. It picks up well, has good flotation, and especially like the hydraulic lift. Its only weak spot is where the pole attaches to the rake frame. Older models had a solid block of steel with a 1¥%-in. hole in it and a bolt and piece of hollow tubing fora bushing. But on new models, they decided to substitute the steel block with a %-in. thick piece of 1%4-in. pipe welded between two pieces of flat iron. This, of course, broke shortly after we bought the rake. The company claims it was caused by abuse so we had to pay to “We had to pay to fix it ourselves.” fix it ourselves. Otherwise it’s a good rake.”

Vermeer 604

2 Best Buys0 Worst Buys
Best Buy
Brad Becker, Alta Vista, Kan. · Vol. 18, No. 6 (1994), p. 14

Brad Becker, Alta Vista, Kan.: A 1994 Vermeer 604 Super J round baler rates as Brad's “best buy". “It’s a quiet, smooth running baler that makes a heavier bale than the 605F model that I traded in, I really like the ‘equal-fill’ electronic control system. It’s very dependable.” On the negative side, Brad lists his 1992 Case-IH 5140 front wheel drive Maxxum tractor, “Overall, I've been well pleased with it except for an electrical short in the powershift transmission that the dealer can’t seem to find. You almost need an electrical engineer to repair this tractor.”

Best Buy
Duane Metheral, Glen Huron, Ontario · Vol. 12, No. 6 (1988), p. 12

Duane Metheral, Glen Huron, Ontario: “Our Versatile 160 tractor is alemon. Every time I start it I’m afraid I'll lose money,” says Duane. “First the brakes failed after the tractor jumped outof gear, causing a rollover that cost $18,000 in repairs. After 800 hours we had to totally rebuild the engine for $8,900. We've had trouble with fuel injectors, universals, the drive shaft, three pto clutches and windows falling out. Also, the company’s 10-ft, hay header takes three hours to install and remove, and works only 50% of the time.” Duane likes his Vermeer 604 J Auto Weave Baler. “It’s as maintenance-free as all the other Vermeer balers I’ve owned during the last LO years, and produces solid bales.”

Vermeer 605C round baler

1 Best Buy1 Worst Buy
Worst Buy
Randy Brooks, Peterstown, W. Va. · Vol. 28, No. 6 (2004), p. 15

“It works fast and does a great job,” says Randy, pleased with his 1980 New Holland 1495 self-propelled haybine equipped with a 12-ft. head. “I’m able to cut 15 acres with it in only two hours.

“My New Holland L775 skid steer loader is a best buy.

“My Vermeer 605C round baler is my worst buy. If the hay is a little green or wet, it clogs up in the baler’s front corners.”

Best Buy
David Swango, Bedford, Ind. · Vol. 12, No. 1 (1988), p. 12

David Swango, Bedford, Ind.: He's happy with his Vermeer 605C round baler. “Starts bales easily and bales as fast as I can drive. The only downtime it’s had is one broken spring and one bearing in over 500 bales. It's a much better baler than my previous 241 IH baler which burned up in the field due to a hot bearing.” David’s “worst buy” is his 1976 White 8800 combine. “This combine clogs up inside so easily you can’t run clean soybeans any faster than 2 to 2 1/2 mph, Theair cleaner and radiator plug up continuously, causing it to overheatall the time. Itdoesn’t even perform as well as my old 403 IH combine which never has clogged up on me.”

Vermeer 1250 BC wood chipper

1 Best Buy0 Worst Buys
Best Buy
Driskel Bros., Nevada, Mo. · Vol. 31, No. 3 (2007), p. 12

“I bought my 1999 Vermeer 1250 BC wood chipper used with about 1,000 hours on it. It’s my best buy. No problems with the motor or grinder. It’s a good machine.

“My 1980 Ford F-350 pickup is a real lemon. Instead of riding in comfort, you get the daylights shaken out of you. The doors rattle like a lumber wagon. It’s not like back in the 1973 to 1979 era, when the Ford F-250 XLTs and F-350’s had class and a comfortable ride.”

Vermeer 2460

1 Best Buy0 Worst Buys
Best Buy
Olin Rairdon, Indianpolis, Ind. · Vol. 18, No. 5 (1994), p. 15

Olin Rairdon, Indianpolis, Ind.: Olin operates a stump cutting business using a Vermeer 2460 stump cutter and a smaller Can Do self-propelled model for grinding stumps that the Vermeer unit can’t reach. He uses a 1964 Deere 3020 tractor equipped with a Westendorf front-end loader to pull the Vermeer and hauls both stump cutters as well as the tractor on a 30-ft. gooseneck trailer between jobs. “The Vermeer stump cutter was originally powered by a Wisconsin 65 hp 4-cyl. gas engine. It kept failing every six or seven months because dirt got through the air cleaner filter. I replaced the engine with a Deutz 950 diesel equipped with an oil bath air cleaner and also mounted an in-line fuel filter in front of the fuel pump. I had the same problem with the 20 hp Kohler engine on the Can Do cutter so I replaced it with a Ruggerini MD 151-D 15 hp diesel engine equipped with an oil bath air cleaner. The engine is made in Italy and sold in the U.S. by Deutz. It developed an oil leak after the warranty expired. My dealer's mechanic found that the problem was caused by a crack in the block. He explained the problem to a Deutz representative who replaced the engine at no cost except for installation. “Engines used in dusty conditions shouldn't have dry-type air cleaner filters. My 1964 Deere 3020 tractor has an oil bath air cleaner and has been overhauled only once.”

Vermeer 3-pt mounted 7-rotor

1 Best Buy0 Worst Buys
Best Buy
Bernard Nash, Indianola, Iowa · Vol. 31, No. 2 (2007), p. 14

“Three years ago I bought a new Vermeer 3-pt. mounted 9-ft., 7-rotor disc mower and it’s my best buy. I use it to mow all kinds of hay ground and also to mow pasture and road banks. I use my International Harvester 656 diesel tractor to pull it. This machine takes only about half as much fuel as my 9-ft. sickle conditioner did to mow the same area and works at least twice as fast. It runs smooth and never plugs up, even on ant hills or in multiflora rose bushes. It’ll mow the heaviest crop of matted-down alfalfa without plugging up.

“There are several people in this area who have large lots of perhaps 20 acres who let me mow their grass twice each summer. I then bale it with my Vermeer 605C baler in June or July which results in a good yield of a grass and clover mixture. Then I cut again in late August or September for a much smaller yield. My mower leaves these lots looking as if they were mowed with a finish mower, and the landowners are quite pleased with how they look.

“This disc mower also runs quiet, because it uses a single shaft drive running out through the bar to individually drive each rotor, which eliminates the need for idler gears.

“This mower has been a pure joy to operate. I doubt that I’ll ever use a sickle mower again.”

Vermeer 404 Pro round baler

1 Best Buy0 Worst Buys
Best Buy
Jim Gore, Ulster, Penn. · Vol. 38, No. 1 (2014), p. 13

“Our 2010 Vermeer 404 Pro round baler is quiet and easy to operate and makes firm, consistent bales. It’s equipped with net wrap so we can use it to make wrapped round bale silage. We’ve made about 3,000 bales so far with no problems.”

Vermeer 503

1 Best Buy0 Worst Buys
Best Buy
Quentin B. Hess, Edgar, Wis. · Vol. 18, No. 5 (1994), p. 15

Quentin B. Hess, Edgar, Wis.: “My 1987 Vermeer 503] round baler is ideal for small farmers. It makes 3-ft. bales which can unroll in the manger in my tie stall barn. “My Vicon 7-wheel H10S0 hay rake works fast and does an excellent job. “Luse a Speedrite 5800 fence energizer to charge an electric fence around our 80acre farm. Our cows have a lot of respect for it.”

Vermeer 5041

1 Best Buy0 Worst Buys
Best Buy
James T. Gray, Prince Albert, Sask. · Vol. 18, No. 1 (1994), p. 15

James T. Gray, Prince Albert, Sask.: “My best buy is my 1992 Vermeer 5041 (5 by 4-ft) solid core baler equipped with all available options including automatic chain oiler, automatic bale kicker, closed circuit hydraulic tension, and automatic electric dual feed tie controlled by an electric monitor (manual override for ticing small bales at the end of the field). It has a 5-bar, small diameter pickup equipped with curved teeth and a spiral start roller that makes it quick and easy to start bales even in dry, chopped straw or short hay. “I've made 1,632 bales with it so far, and it looks like the 2-ply belt lacings will last well over 2,500 bales. The belts are very forgiving in realigning themselves, even in long, swathed green wheal. I really like the hydraulic bale tension adjustment that uses a simple hand valve and lock. No tools are required. It lets me switch from making hay bales at 180 Ibs. pressure to straw bales at over 250 Ibs. pressure. Mostair cylinders on other balers have a maximum pressure of only 80 Ibs. “The baler makes solid bales thatare easy to unroll by hand. The electronic monitor can easily be set to increase or reduce the amount of twine on center and end wraps. When set on automatic wrap, the monitor wars when the bale is nearly full, both visually and audibly. It also indicates when the needles start out from their home position and when it’s time to eject the bale. A flashing light on the screen shows when the end gate is open. The automatic bale field count is accurate because a bale has to be tied in order to be counted. There should be a warning in the operator's manual, ‘Make certain your tractor seat is comfortable because you'll have no real reason to leave it except to add more twine.””

Vermeer 504C round baler

1 Best Buy0 Worst Buys
Best Buy
Bobby J. Hardy, Jr., Hull, Ga. · Vol. 20, No. 3 (1996), p. 15

“In 1978 we bought a Vermeer 504C round baler. We used it for 11 years in all kinds of conditions and all we replaced were two bearings in the belt rollers and a couple of slip clutches. We had the belts re-laced twice and when it left our farm in 1989 it still had the original belts. We traded it in for a Vermeer 504I round baler which is also a best buy. Vermeer balers are simple to work on and parts are easy to get. “My two 1978 Ford trucks are both best buys. I think 1978 and 1979 Ford trucks were some of the best trucks Ford ever made. Both of mine still run great. I’d like to hear from other readers who own these trucks.”

Vermeer 504F

1 Best Buy0 Worst Buys
Best Buy
Sam McConnell, Bogata, Tex. · Vol. 12, No. 2 (1988), p. 12

Sam McConnell, Bogata, Tex.: He’s had trouble with his Vermeer 504F round baler. “I bought this baler new and have always had trouble with hay going to the top of both outside belts and hanging on the top belt guides. Vermeer has been no help except to suggest that we remove one 4-in, belt, which didn’t help. Have any FARM SHOW readers solved this problem?” Sam's happy with his 5-year-old Farmhand 235 front-end loader, “It does every job the way it’s supposed to. I can put it on or take it off in 5 min.” Garfield Gillis, Point Prim, Prince Edward Island: “Our Deere 2755 4-WD tractor has lots of power and front-wheel tilt when turning, wiich makes it easy to maneuver around feedlots. The only complaint 1 have about the tractor is that they moved the gear shift forward on the 55 Serics to make it easier to get on and off. The problem is that it’s more difficult to shift.”

Vermeer 504 Pro silage baler late

1 Best Buy0 Worst Buys
Best Buy
Roman Yoder, Hutchinson, Kansas. · Vol. 42, No. 6 (2018), p. 15

“I bought a used 2016 Vermeer 504 Pro silage baler late in 2017 and used it this year to bale triticale, alfalfa, sudan balage, dry alfalfa, grass, and millet hay. It does a good job in wet or dry hay and makes a nice, dense bale. It has a huge appetite, and it’s easy to service.

“My 2003 Supreme 300 vertical feed mixer does a good job and has been trouble-free (www.supremeinternational.com; ph 800 563-2038).”

Vermeer 504R Signature round baler

0 Best Buys1 Worst Buy
Worst Buy
Andrew R. Pope, Chatham, Va. · Vol. 44, No. 6 (2020), p. 15

Andrew’s impressed with his 2015 Kubota RTV-X1120 utility vehicle equipped with a diesel engine. “It has plenty of power, and a hydrostatic transmission that’s smooth and provides engine braking whenever I release the throttle. When you consider the high payload capacity, I think this is the best utility vehicle out there.”

On the negative side, he lists his 2019 Vermeer 504R Signature round baler. “The dealer reviewed everything on this baler with me after the purchase. Once I got home, I noticed the sprocket that drives the rotor and pickup had excessive runout. The sprocket is bolted to a hex shaft on one end of the stripper roll. I used a dial indicator to measure the runout of the shaft and found that it had 0.035 in. runout. Also, the bearing mounting plate was flexing 0.010 in.

“The dealer ordered a new stripper roll and sent a mechanic to help me install it. The hex shaft on the new stripper roll measured 0.015, which was still more than I would like but better than before.

“The stripper roll was replaced under warranty. The Vermeer rep told the dealer that I was the only one with this problem, which I find hard to believe. If your Vermeer 504R baler is wearing out bearings on the right side of the stripper roll, you might have the same problem.

“The next problem I had to tackle was the design of the windguard on the crop pickup. Under certain conditions, such as when the pickup drops into a low spot while baling thick hay, the windguard gets pushed into the stripper roll. I was sent a set of check chains to keep this from happening, but it didn’t help. Then, I removed 5 in. from the end of each finger on the windguard and the problem was solved.

“This baler is well built, but I shouldn’t have to fix new equipment like I did.”

Vermeer 505

1 Best Buy0 Worst Buys
Best Buy
Dwain W. Case, Wesson, Miss · Vol. 19, No. 4 (1995), p. 14

Dwain W. Case, Wesson, Miss.: “My 1992 Vermeer 505 round baler is the best and simplest baler on the market. It makes nice bales and is easy to operate. “My 1991 Fella 8-ft. mower is my worst buy. A bearing in the sicklebar went out, four oil seals in the gearbox failed, the lift arm pins broke off, and numerous welds broke, All of this happened during one hay season, The following year I bought a New Holland mower, love it.”

Vermeer 5051

1 Best Buy0 Worst Buys
Best Buy
Jeffrey Rash, Bristol, Va. · Vol. 13, No. 3 (1989), p. 14

install, "It warms air outside the house, then blows it into the home through a windowmounted duct. We use it to heat our entire house. It sets outside so there’s no mess in the house and we don’t have to pack wood into the house as it’s piled near the stove. The outside temperature can be below zero and our house will be 76°.” Jeffrey Rash, Bristol, Va.: Jeffrey-says his “best buy” is his 1988 Vermeer 5051 round baler. “Vermeer makes the best round baler on the market and it produces the lightest and best looking bales. I've used a New Holland round baler and there’s no comparison.”

Vermeer 505 Rebel round baler

1 Best Buy0 Worst Buys
Best Buy
Donald R. Miller, Dongola, Ill. · Vol. 32, No. 6 (2008), p. 13

“My 2006 Vermeer 505 Rebel round baler is as near perfect as any machine I’ve ever owned.

“I own five Allis Chalmers D17 tractors and they’re all still in great shape. We bale a lot of hay and these tractors are all used in our haying operation.”

Vermeer 505 Super baler

1 Best Buy0 Worst Buys
Best Buy
C.E. Kimble, Adrian, Mo. · Vol. 22, No. 2 (1998), p. 15

“My 1997 Vermeer 505 Super baler works great. The only difficulty I experienced with it last year involved the twine, and it wasn’t the baler’s fault. “My 1997 Troy-Bilt 16 hp lawn tractor equipped with a 2-cyl. Briggs & Stratton gas engine is a pleasure to operate.”

Vermeer 530

1 Best Buy0 Worst Buys
Best Buy
Charles Graham, Quaker City, Ohio · Vol. 18, No. 1 (1994), p. 16

Charles Graham, Quaker City, Ohio: A Vermeer 530 pull-type rotary mower/ conditioner rates as Charles’ “best buy”. “It reduces mowing time, does a great job of cutting hay, and speeds up hay drying time.”

Vermeer 554XL round baler

1 Best Buy0 Worst Buys
Best Buy
Doug Dewing, Grantsburg, Wis. · Vol. 33, No. 1 (2009), p. 13

“My 2002 Vermeer 554XL round baler makes 4 by 5 1/2-ft. bales and is easy to operate. No problems. The bale size works well for us, as we sell a lot of horse hay and the bales fit comfortably in back of a 1/2-ton shortbed pickup. With a 4-ft. wide bale I can haul several on a trailer without being overwidth.”

Vermeer 604 Super J round baler

1 Best Buy0 Worst Buys
Best Buy
Richard Dunlap, Cedar Falls, Iowa · Vol. 16, No. 4 (1992), p. 12

Richard Dunlap, Cedar Falls, Iowa: Richard's impressed with his 1991 Vermeer 604 Super J round baler. “I do custom baling and have bought four new Vermeer balers in the last four years, with no breakdowns or repairs on any of them.”

Vermeer 605E

0 Best Buys1 Worst Buy
Worst Buy
Vic Stratman, Argyle, Mo. · Vol. 18, No. 2 (1994), p. 16

Vic Stratman, Argyle, Mo.: Vic says his “best buy” is his 1990 Chevrolet Astro Van equipped with a 6-cyl. engine. “It had a lot of problems at first but the dealer solved them. Now it works great.” On the negative side, “My Lincoln pistol grip grease gun costa fortune and I couldn't keep air out of it.” “My 1992 Vermeer 605E round baler is also a worst buy. I thought the Vermeer name meant quality. However, I found out that the 605E wasan experimental baler that had had a lot of problems, That’s.an understatement. It wasn’ ttoo bad the first year but last year everything on it broke that could. Finally the gearbox went out. That was it. Anyone need parts for a 605E? I’m junking this one.”

Vermeer 605-L baler

1 Best Buy0 Worst Buys
Best Buy
Ross McGehee, Natchez, Miss. · Vol. 25, No. 3 (2001), p. 16

“Our Vermeer 605-L baler is our best buy. We replace balers every three years to keep current with warranties and new technology. The company always fixes the little things that you hardly even notice when they update their machines. We’re continually impressed with their design improvements and are looking forward to operating a new 605 XL model that we recently purchased.”

Vermeer 605 Super J round baler

1 Best Buy0 Worst Buys
Best Buy
Mark Danielson, Rothsay, Minn. · Vol. 16, No. 6 (1992), p. 12

Mark Danielson, Rothsay, Minn.: “It has performed well under a variety of conditions, including rotary combined straw,” says Mark, pleased with his 1991 Vermeer 605 Super J round baler, “It’s easy to operate and service. An outstanding product.”

Vermeer 605 Super M round baler

1 Best Buy0 Worst Buys
Best Buy
Wayne Eltiste, Tecumseh, Neb. · Vol. 38, No. 4 (2014), p. 13

“I’ve used my 2012 Vermeer 605 Super M round baler to make more than 3,000 bales, yet the pickup has only plugged up once, and that was probably due to ‘pilot error’. The net wrap has pulled off just one bale. This machine really speeds up baling.”

Vermeer 605XL baler

1 Best Buy0 Worst Buys
Best Buy
Greg Kropf, Westphalia, Kansas · Vol. 30, No. 3 (2006), p. 14

“My 1999 Deere 925 mower conditioner is my best buy. I especially like the flail conditioner, which can pass objects through without damaging the machine. This machine just mows and mows without problems. It has held up well over thousands of acres.

“My 1966 Deere 4020 tractor is a best buy. It rarely has problems and is worth exactly what I paid for it six years ago.

“My 1999 Deere 6310 tractor is comfortable, quiet, and does a good job of handling our mower and round baler. The power quad transmission lets us work fast in the field. It lets me mow our field 30 minutes quicker than with my 4020, just because of its ability to easily and constantly change gears.

“My 2003 Vermeer 605XL baler makes a good bale and the pickup gets all the hay. However, it has had a lot of problems.

“My 2004 Vermeer WRX rake does a good job and is easy to adjust. However, it’s four real tires, a good paint job, and some better-grade bolts away from being a best buy.

“My Deere 1600 hydraswing mower conditioner never made it through a field without breaking down. The final blow came when we couldn’t get it unhooked from the tractor’s pto shaft, and we ended up having to take the pto shaft out of the tractor.”

Vermeer 6S0F

1 Best Buy0 Worst Buys
Best Buy
Laurence Sanderson, McLouth, Kan · Vol. 19, No. 3 (1995), p. 15

Laurence Sanderson, McLouth, Kan.: A 1993 Case-IH 5220 tractor and a 1980 Vermeer 6S0F round baler are two of Laurence’s “best buys”. “The Case starts at low temperatures with no problems. The 3-pt. has tremendous lift capacity, so much that I’ve already bent two mounted implements. The Cummins diesel engine is very fuel efficient. The Vermeer baler is built like a tank. I've had to replace only two bearings and the drive chain in 15 years. In my opinion it makes a tighter wrapped bale than any other baler on the market,”

Vermeer 8040 rotary mower

1 Best Buy0 Worst Buys
Best Buy
Martin Heller, Berthold, N.D. · Vol. 46, No. 5 (2022), p. 14

“My Vermeer 8040 rotary mower is well-built and performs well. But it’s a real pain in the rear to hook up or unhook from the tractor. For some unknown reason, instead of the 3-pt. hitch attaching in a normal way, the sick, twisted engineer who designed it decided it should be slid in from one side. This means that instead of spreading the 3-pt. arms and backing up to the machine, I have to back up to the machine a bit off center and then use my skid steer to move the mower over to fit onto the pins as they both have to attach from the same direction. I believe the engineer was dropped on his head as a child since this procedure is almost impossible to perform alone. It sometimes literally takes hours to attach/detach from the tractor when working alone. Once attached, the machine performs flawlessly.”

Vermeer 830 discbine

1 Best Buy0 Worst Buys
Best Buy
Vic Stratman, Argyle, Mo. · Vol. 40, No. 5 (2016), p. 15

“A few years ago I bought a used Deere 6400 MFWD loader tractor with about 3,200 hrs. on it. It now has more than 9,000 hrs. It’s an amazing tractor. I don’t know how it could be improved.

“My Vermeer 830 discbine is an amazing machine.

“I’m not impressed with my H&S 8-wheel V-rake.”

Vermeer G baler

0 Best Buys1 Worst Buy
Worst Buy
Joe Rupnicki, Soldier, Kansas · Vol. 29, No. 6 (2005), p. 12

“I traded an old broken down Vermeer G baler for a new Vermeer Rebel 5400 baler. It has trouble starting bales and plugs up all the time. Also, the electric tie won’t go all the way to the middle and instead would tie only about a foot on each end. The company people came out and made excuses. They told me either the windrow was too narrow, or the hay too heavy, or that I was going too fast. No matter what I did to try to solve the problem, nothing worked. I sent photos to the company but never heard back from them.

“This year I used it to make only 40 bales, yet the baler plugged up seven times. My dealer said the problem was that the hay was harder to bale this year. This is the worst machine I’ve ever bought. I had to buy hay in 2003 and 2004 and now I’ll have to buy hay again this year. The amount of hay that I’ve had to buy would have made three baler payments. If I knew then what I know now, I would never have traded my broken G model for this machine.”

Vermeer L big round baler

1 Best Buy0 Worst Buys
Best Buy
Donald R. Nutt, Center, Mo. · Vol. 23, No. 2 (1999), p. 15

“I had virtually no problems making 1,200 bales last season,” says Donald, pleased owner of a 1998 Vermeer L big round baler. “I traded a 1993 Super J for it. The Super J was a good baler but the L makes heavier bales with less stress on the operator. That’s important to me because I do custom baling and my baler has to run.”

Donald’s worst buy is a 1987 FordRanger pickup equipped with a 4-cyl. 2-liter engine and 5-speed transmission. The first year, mileage was a fair 20 to 24 mpg. Then it dropped to 16 to 18 and had no power. I ran it to 113,000 miles and traded it for a 1980 Chevy 1/2-ton Scottsdale just to be rid of it.”

Vermeer MC3300 mower conditioner

1 Best Buy0 Worst Buys
Best Buy
Loyal Fulton, Selma, Iowa · Vol. 42, No. 4 (2018), p. 13

“Last year I bought a new Vermeer MC3300 mower conditioner. I have a rough farm but the hydraulic suspension on this machine follows the ground closely, with no scalping. Also, the knives on the machine stay sharp much longer than on mower conditioners equipped with a spring suspension system.”

Vermeer Model J baler

0 Best Buys1 Worst Buy
Worst Buy
Herman Daugherty, Bogard, Mo. · Vol. 15, No. 5 (1991), p. 12

Herman Daugherty, Bogard, Mo.: Herman's had trouble with two Morton buildings, “We put the first one up 10 years ago and it always leaked, The company came out a couple of times but never repaired it, We hired a carpenter and he fixed it. Last year we bought another Morton building and paid the company extra money to bird-proof it. The birds can’t get in, but they do build nests in the door track. When we open the sliding doors the nesting material falls inside the building, “Our 1990 Vermeer Model J baler is also a worst buy. When my son he comes in at night after a day of baling, the first thing his wile asks is ‘How many shear pins did you use today?’ We also had to replace a bearing before we had even made 900 bales.”

Vermeer R-23

1 Best Buy0 Worst Buys
Best Buy
Scott Jay Claussen, Denison, Iowa · Vol. 19, No. 5 (1995), p. 15

Scott Jay Claussen, Denison, Lowa: “My 1992 Vermeer R-23 twin hay rake is a real time saver and handles hay gently. In thick hay it makes baling almost too easy because I can make windrows that cover the width of the baler. There's no need to weave back and forth with the baler. I can roll two 14-ft. windrows together and save a lot of driving time with the baler. “My 1991 Chevrolet 2500 4-WD pickup is my worst buy. I’ve had to replace the rear end, transmission, starter, and alternator. There also were electrical problems. The warranty took care of the rear end, transmission, and electrical problems. Also, it isn’t very fuel efficient. It gets only 8 to

Vermeer Rebel round baler

1 Best Buy0 Worst Buys
Best Buy
James J. Countryman, Ontonagon, Mich. · Vol. 35, No. 2 (2011), p. 15

“My 2008 Montana 5740 C tractor starts and runs well and has controls that are easy to operate. I use this tractor to plow, plant, cut and bale hay, and to load and feed round bales. I also plow snow with it using an oversized snow bucket.

“I’ve put more than 800 hours on my 2007 Kubota RTV 900 utility vehicle with only routine maintenance. I use it to pull a water wagon and to haul wood and hay, and to do numerous other hauling chores around our farm and garden. It works great with a front hitch for backing 4-wheel wagons into place.

“My 2008 Vermeer Rebel round baler has performed as advertised. No problems.”

Vermeer Rebel 5400 baler

0 Best Buys1 Worst Buy
Worst Buy
Joe Rupnick, Soldier, Kansas · Vol. 32, No. 6 (2008), p. 15

“The Vermeer Rebel 5400 baler that I bought new a few years ago is a worst buy. The company won’t do anything to fix it. I wrote a letter to the Kansas attorney general, who contacted the company. The company told them they had solved the problem, yet no one from the company ever came out to look at it. It plugs up nine or ten times for every 50 bales.”

Vermeer Signature Series 4

1 Best Buy0 Worst Buys
Best Buy
Ken Gilbertson, Ada, Minn. · Vol. 46, No. 1 (2022), p. 15

Ken’s “best buy” is a 2020 Vermeer Signature Series 4 by 5 round baler. “There have been no problems in 2 years of use. I really like the camless pickup. Starting a bale is fast and easy.”

Vermeer Super 605 J baler

1 Best Buy0 Worst Buys
Best Buy
George Brown, Devils Lake, N.D. · Vol. 16, No. 1 (1992), p. 14

George Brown, Devils Lake, N.D.: “It makes good uniform bales and outworks any baler I've seen. Very few problems,” reports George, owner of a “best buy” 1991 Vermeer Super 605 J baler.

Vermeer Super F baler

1 Best Buy0 Worst Buys
Best Buy
Robert Eastwood, Underwood, Minn. · Vol. 15, No. 5 (1991), p. 14

Robert Eastwood, Underwood, Minn.: Robert bought a Jonserud 2051 chain saw last winter, “It handles good and cuts fast.” He does custom work with his 1982 Vermeer Super F baler and says it’s a “best buy”. “After 15,000 bales it still works good. All I've replaced is one belt and bearings on the main drive. New rubbermounted pickup teeth were put in 6,000 bales ago and still show no wear. “My 1980 Vermeer twin rake is also a “best buy”.

Vermeer Super J round baler equipped

1 Best Buy0 Worst Buys
Best Buy
Herschel Carriger, Chapin, Ill. · Vol. 21, No. 3 (1997), p. 15

“I’m impressed with my 1993 Vicon mower conditioner. It does a good job of mowing any crop at 9 mph. I can mow all day long without having to look back to make sure it’s not plugging up. When I’m ready to mow I just go to the field - no need to make repairs first like on a sicklebar. The driveline design is ‘chatter-free’ even on corners, and it’s equipped with adjustable wings that let me narrow the 10 1/2 ft. cut to any width I want. The only problem is that there aren’t many dealers in our area. “Combined with my 8-wheel V rake and Vermeer Super J round baler equipped with a bale kicker, I have a great baling team.”

Vermeer Super K baler

1 Best Buy0 Worst Buys
Best Buy
Donald Hutson, Paris, Ky. · Vol. 23, No. 3 (1999), p. 16

“It tows six 1,800 to 2,000-lb. round bales with ease,” says Donald, pleased owner of a 1999 Ford F-250 Super Duty 4-WD pickup equipped with 5.4-liter engine, automatic transmission, and 4:10 axles. “The truck handles extremely well and has ample power. We like the style of the new Louisville Line. We also like the straight axle and lock in and out manual front hubs.”

He also likes his 1996 Vermeer Super K baler. “We’ve made over 3,000 bales with it, no problems.”

Vermeer TE1710 4-star tedder

1 Best Buy0 Worst Buys
Best Buy
Nelson N. Burkholder, New Holland, Penn. · Vol. 50, No. 5 (2026), p. 15

Nelson is pleased with his 2023 Vermeer TE1710 4-star tedder. “It spreads heavy spring forage with…”

This listing is from the current issue of FARM SHOW. Subscribe to read it all or get a free issue.

Vermeer TM1410 trailed mower

1 Best Buy0 Worst Buys
Best Buy
Rex Coulter, Tyler, Texas · Vol. 45, No. 4 (2021), p. 15

Rex nominates his Vermeer TM1410 trailed 20-ft. mower as his “best buy”. “It’s easy to operate, hook up to, and maintain, and changing blades on it is an easy job. How fast we can go and how much we can cut in a day depends on the hay, ground condition, and tractor size. We can usually cut 12 to 13 acres per hour when using our 110 hp. tractor, but with a 120 hp. tractor it cuts even better. This is our third Vermeer mower. The first two worked great, but the 1410 cuts 2 1/2 ft. wider and is easier to service. If you ever use one of these, I doubt you will run anything else.”

On the negative side, “Our 3-pt. mounted Junior Burrow Builder comes with a hopper that holds 5 gal. of poison bait for pocket gopher control. It has a big depth control wheel on back. It seems to be well-built but it won’t operate as advertised. When we tried using it on a 100 plus hp. tractor, the poison only dropped about 70 percent of the time.

“We switched to an 85 hp. tractor and it built the burrows fine, but it dropped poison only about 10 percent of the time. We adjusted the wheel as low as it would go, but it didn’t help. We also added more than 200 lbs. of weight, which helped a little. Then we drilled holes and moved the wheel down 1 1/2 in., which resulted in about an 85 percent poison drop in sandy soil. We plan to wrap part of a 4-wheeler tire on top of the press wheel so it’ll work better. I hate to buy anything that I have to work on the first time I use it.”

Vermeer TM 700 disc mower

1 Best Buy0 Worst Buys
Best Buy
Rex Hollar, Scranton, Kan. · Vol. 34, No. 2 (2010), p. 14

Rex is pleased with his 2007 Vermeer TM 700 disc mower and 2008 Vermeer WR 22 wheel rake. “We had to make some changes to our hay operation so I turned to my Vermeer dealer. After using the disc mower for a month I wished we had bought it sooner. Then getting the wheel rake just made it a sweeter deal for our big baler. These machines have been reliable and are real time savers.

“Over the years we’ve used our Vermeer 504 Super I round baler to make several thousand bales, and it has required only routine maintenance. We take the baler back to the dealer every winter to have it checked over, which lets us keep going without having to stop for repairs during the busy hay season.”

Vermeer TM800 disc mower

1 Best Buy0 Worst Buys
Best Buy
Morley Hamilton, Hillsboro, Ky. · Vol. 43, No. 4 (2019), p. 15

“The Vermeer TM800 10-ft. disc mower I use with my 60 hp. tractor does an excellent job. My Vermeer 544XL round baler also works good.”

Vermeer WRX rake

1 Best Buy0 Worst Buys
Best Buy
Greg Kropf, Westphalia, Kansas · Vol. 30, No. 3 (2006), p. 14

“My 1999 Deere 925 mower conditioner is my best buy. I especially like the flail conditioner, which can pass objects through without damaging the machine. This machine just mows and mows without problems. It has held up well over thousands of acres.

“My 1966 Deere 4020 tractor is a best buy. It rarely has problems and is worth exactly what I paid for it six years ago.

“My 1999 Deere 6310 tractor is comfortable, quiet, and does a good job of handling our mower and round baler. The power quad transmission lets us work fast in the field. It lets me mow our field 30 minutes quicker than with my 4020, just because of its ability to easily and constantly change gears.

“My 2003 Vermeer 605XL baler makes a good bale and the pickup gets all the hay. However, it has had a lot of problems.

“My 2004 Vermeer WRX rake does a good job and is easy to adjust. However, it’s four real tires, a good paint job, and some better-grade bolts away from being a best buy.

“My Deere 1600 hydraswing mower conditioner never made it through a field without breaking down. The final blow came when we couldn’t get it unhooked from the tractor’s pto shaft, and we ended up having to take the pto shaft out of the tractor.”

Vermeer bale carrier

1 Best Buy0 Worst Buys
Best Buy
Hubert Hegtvedt, Mabel, Minn. · Vol. 14, No. 1 (1990), p. 13

Hubert Hegtvedt, Mabel, Minn.: “My Vermeer bale carrier and unroller is a best buy. It's foolproof and simple to use.”

Vermeer haying equipment

1 Best Buy0 Worst Buys
Best Buy
Gary Nonamaker, Cedar, Kansas · Vol. 32, No. 3 (2008), p. 13

Gary’s impressed with his Vermeer haying equipment. “I bought a new Vermeer 605F baler in 1979 and used it every year through 2006 with very few problems. It still had the original belts when I traded for a new 605M model. When I decided to update I didn’t even look at any other brand. I made about 1,300 bales with the 605M model last year. It’s an awesome piece of equipment and can bale double windrows of alfalfa at 10 mph and huge windrows of cane at 8 mph. When baling cane there were times that it would make a bale and wrap it in only 50 seconds.

“When I took delivery of the 605M in January, 2007 my dealer informed me of a recall because of a change made in the bearings used in the rollers. The company sent two men out to my farm who worked for several hours to change seven different rollers. The machine probably would have lasted until the warranty on it expired and they could have gotten by. To me this showed the integrity of this company.”

Vermeer model

1 Best Buy0 Worst Buys
Best Buy
Eldon Williams, Dansville, Mich. · Vol. 14, No. 3 (1990), p. 13

Eldon Williams, Dansville, Mich.: A 1986 Vermeer model LS 150A log splitter heads Eldon’s “best buy” list. “Ithas its own hydraulic system and 5 hp engine mounted ona trailer. It splits logs with the bar in the vertical position sol don’t have to lift blocks upon the bar, One person can easily operate it. “My Polaris Trail Boss 250 ATV is another best buy. I use it to check fence, herd cattle, spray fence rows and crops, and to haul a small trailer.” On the negative side, “The fuel pump on my 1988 White 37 tractor failed after about 10 hours. The dealer couldn’t locate the same fuel pump so he temporarily installed an electric fuel pump. This tractor has a higher horsepower rating than my 1953 Ford NAA, but it can’t do as much work, I traded it for the next larger size, model 43, but it didn’t work any better because couldn't keep it in gear. The dealer tried to repair the transmission, but was told that it had to be replaced. By this time White had introduced its American-made 60 and 80 models so I traded model 43 for model 60. However, after one hour of use a seal in the power take off failed and it started throwing oil. By now I was almost ready to give up, but the dealer and company replaced the seal and made other changes. The tractor now has about 175 hours with no more problems.”

Read every report in full

FARM SHOW has run reader Best & Worst Buys since the beginning.

Subscribe to FARM SHOW