Real farmers rate what they bought, from FARM SHOW MagazineSubscribe  ·  Free issue  ·  Send us your Best or Worst Buy
Subscribe to FARM SHOW
Home › Issues › Vol. 5, No. 6 (1981)

Best & Worst Buys: FARM SHOW Vol. 5, No. 6 (1981)

41 reports from pages 10–12 · 35 Best Buys7 Worst Buys · See everything in this issue at FARM SHOW →

Best Buy

Randy Jacobs, Alden, Minn · Vol. 5, No. 6 (1981), p. 10

Randy Jacobs, Alden, Minn: “Our Badger feed wagon has been a lemon since we got it. In less than a year, the axle tore loose from the frame, which we've rebuilt. There are no bearings, just loose fitting bushings. The drive system is so light that we are always reinforcing the framework around all the shafts. It's just plain built cheap and too light. The service needs improving.” Randy says his ‘best buy” has been his 1980 Mazda GLC. “For a small car, it has an extremely smooth ride and many convenience items. The gas mileage is great, as high as 38 miles per gallon on trips, loaded with luggage. That's with an automatic transmission. Absolutely no problems and service is super. “Two other good buys are our Johnson Energy Converter wood burner and our Fence Tight fence crimper. The wood burner has really been a money saver when it comes to heating our big house. The fence crimper tightens all kinds of fences inate quickly without any harm to the wire,”

See this page at FARM SHOW →
Best Buy

Bauer + 1 more

E.K. Habersetzer, Raymond, Wash · Vol. 5, No. 6 (1981), p. 10

E.K. Habersetzer, Raymond, Wash: He's happy with his Bauer F111 RD manure pump. “We'd used an older model Bauer pump since the mid 60's and were well satisfied with it. Then, we bought the new F111 series and wow! It puts out more with the tractor at half throttle than the old one did wide open.” On the minus side, he's disappointed with his new Allis Chalmers 185 tractor. “We've been with AC for years, We have a WD 45 that is a great old workhorse and a D17 that can handle a 16-in. three bottom plow ata trot, and now Allis Chalmers puts out a 75 horsepower 185 that won't do any more than the D17 at 55 horsepower.”

See this page at FARM SHOW →
Best Buy

Ram

G.W. Carroll, East Ely, Nev · Vol. 5, No. 6 (1981), p. 10

G.W. Carroll, East Ely, Nev: He's had problems with his 1980 Dodge 150 4x4 pickup. ‘‘The brakes were too small and kept breaking. It had a slant six engine and, with the motor mounts set right under the fuel pump, the pump kept breaking off. The factory installed the wrong front end gear ratio against the rear end. The bed was just caulked, not welded. The pickup was cheaply made.”

See this page at FARM SHOW →
Worst Buy

Marlyn Hefti, Marshall, Minn · Vol. 5, No. 6 (1981), p. 10

Marlyn Hefti, Marshall, Minn: ‘My ‘worst buy’ is a County Atlas from Midland Atlas Company in Mil bank, S.D. They came to check if information about our place was correct, but when got my copy they had everything wrong. It cost me $49.40."

See this page at FARM SHOW →
Best Buy

Vermeer + 1 more

Robin Robinson, Lovelady, Tex · Vol. 5, No. 6 (1981), p. 10

Robin Robinson, Lovelady, Tex: Robin likes his 605 F Vermeer round baler. “This baler has been very dependable and easy to operate. I've had one bearing go out in more than 2,000 rolls of hay. It puts up a consistently tight bale.” Robin's disappointed, however, with his Caraway V-type front end rake. “We purchased the rake from a local dealer and were told it would work well on any tractor in any type of hay. We found thé rake caused all of our tractors to overheat, including a 100 hp John Deere. Secondly, it would not rake our thick hay because the hay built up in front of the tractor and made a great mounded windrow that our trailing baler could not begin to handle. ‘When we went to the rake dealer for some solutions to our problems, there were none. He told us that we were the only ones having the overheating problem, which was the problem we were most upset by. We tried to trade the rake in to the dealer where we purchased it. He wanted to charge us $700 for raking about 100 rolls of hay. None of the other dealers in town even wanted to consider a trade with us, including the Vicon dealer who supplies the basic rake to Caraway. They wanted $3,000 difference between our two-month-old rake and their $5,600 rake.”

See this page at FARM SHOW →
Best Buy

International Harvester + 1 more

Ernest Hayl, Shandon, Calif · Vol. 5, No. 6 (1981), p. 10

Ernest Hayl, Shandon, Calif: “Our 453 hillside IH combine was so poorly put together that we were broken down most of the time. The dealer and International people tried to blame all the breakdowns on operator neglect. Finally, we showed them that it had been assembled with poor alignment, which put the combine in a continuous strain. They made it better but it certainly cost us in downtime. “The International dealer in our area quit so we have had a hard time getting service and parts for our IH equipment. It shows that they don't seem to care for their customers. We have purchased IH equipment for over 40 years. We have three [H combines, four crawler tractors and a 4366 wheel tractor.” On the plus side, Ernest says he's pleased with his 30-ft. Marvin cultivator and 4890 Case tractor. ‘“The cultivator is lifted like a sulky rake so you can clean out the trash rapidly by dumping it. The construction is good so there's no problems breaking the frames, and so on. Our Case tractor does a super job. The dealer gives the best service possible.”

See this page at FARM SHOW →
Worst Buy

Wells Raben, Torrington, Wyo · Vol. 5, No. 6 (1981), p. 10

Wells Raben, Torrington, Wyo: He's had good luck with his ‘‘Skuttle grain moisture tester. It's easy to use, gives accurate readings and is cheaper than competitive models we looked at,"’ he reports. “IT don't have a specific ‘worst buy’, Wells adds, “but I think most agricultural people will agree that the service and treatment you receive for most anything you have done in town just isn’t as good as it should be. It seems most town people don’t care whether they help you or not, just as long as they get you out of their hair. Not all of them, but a good:proportion of them.”

See this page at FARM SHOW →
Best Buy

Case

Real Deslauriers, Napierville, Quebec · Vol. 5, No. 6 (1981), p. 11

Real Deslauriers, Napierville, Quebec: “This tractor has power to spare,”’ says Real, happy with his Case 2090 tractor. ‘‘Handy controls, excellent cab, fuel economy, power shift transmission and it gets the best possible service from my local dealer.”

See this page at FARM SHOW →
Best Buy

White

Bruce B. Anderson, Waconia, Minn · Vol. 5, No. 6 (1981), p. 11

Bruce B. Anderson, Waconia, Minn: “In the fall of 1978, I bought a Natural Curing brand drying/storage bin at a time when corn was around 20% moisture. We found out that we do not have enough heat units per day to dry the corn and it took till the following spring and summer to dry the 13,000 bu. completely. In 1979, the fall was wetter with corn at about 28 to 30% moisture and higher. We ended up with a lot of damaged corn. I did dry 4,000 bu. of beans with it from 19% to 1242% moisture in three days of running during daylight hours only. But, to spend over $20,000 for a galvanized garbage can that doesn’t dry in the fall is questionable, I can't contract new crop corn unless I dry a couple thousand bushels at a time. “I'm pleased with my new White 4-row 378 corn cultivator, It has the Danish spring teeth.”

See this page at FARM SHOW →
Best Buy

Wesley Larrabee, Shoreham, Vt · Vol. 5, No. 6 (1981), p. 11

Wesley Larrabee, Shoreham, Vt: “We've found that our 3002 Agtec orchard sprayer has done an exceptional job keeping our orchard covered this 1981 growing year,"’ says Wesley.

See this page at FARM SHOW →
Best Buy

International Harvester

Lloyd Kuchta, Yankton, S. Dak · Vol. 5, No. 6 (1981), p. 11

Lloyd Kuchta, Yankton, S. Dak: “A real lemon and no service is what got when I bought my International 1086 tractor,’ Lloyd told FARM SHOW. "The tractor used one gallon of oil a day while it was still under warranty. They said it would stop but, when it got worse, they overhauled it and gave me the bill, Thanks to Farmer's Coop and the warranty I got for using their oil inthe engine, they paid for the overhaul, ‘ also had trouble with the torque shifting down at idle while it was under International warranty and they told me it wasn't anything to worry about. Later, after the warranty was out, I learned from a different dealer that it shouldn't shift down at “The tractor rides rough, steers hard and the front wheels stand at an angle. Truly a lemon.” idle. told my dealer and he then admitted the information was correct but that the warranty was out and he couldn't do a thing about it. “The tractor shifts hard, rides rough, steers hard, a person can't see the drawbar from the seat, the front wheels stand at an angle so the tires wear out on the outside. It is truly a real lemon,” he concludes. “My ‘best buy’ would have to be Farmers Coop Oil.”

See this page at FARM SHOW →
Best Buy

Jon W. Brower, Claremont, Minn · Vol. 5, No. 6 (1981), p. 11

Jon W. Brower, Claremont, Minn: Jon was pleased by the results of Sutan-Plus by Stauffer Chemical Co. “Thad excellent control of grass in my corn by incorporating Sutan. I applied three quarts per acre and incorporated twice with a field cultivator,”’ he says. “On the other hand, I applied Treflan on my soybean fields and double incorporated it with a field cultivator and had poor soybean emergence on sloping land and poor foxtail control on heavy level land. I used Treflan two years earlier on the same ground incorporated with a disk and had excellent results."

See this page at FARM SHOW →
Worst Buy

Ford

Evan J. Brown, Richfield, Idaho · Vol. 5, No. 6 (1981), p. 11

Evan J. Brown, Richfield, Idaho: “We bought our first three-wheeler two years ago and were so pleased with it we bought a second one this year,’ says Evan, happy with his Honda ATC. “It's the least cost piece of equipment on the farm. Two people can fide it and you can haul everything from a sack of salt to 40 ft. of gated irrigation pipe. “Although this isn’t really a ‘worst buy’. we had a bad experience with our 9700 Ford tractor. The tractor has worked out fine, but before it was even unloaded we noticed one bad tire and also that both rear axles were leaking oil. Both the driver of the truck and the dealer assured us the problems would be taken care of but so far we have not been reimbursed as promised.”

See this page at FARM SHOW →
Best Buy

International Harvester

R.J. Kraft, New Braunfels, Tex · Vol. 5, No. 6 (1981), p. 11

R.J. Kraft, New Braunfels, Tex: He likes: his IH 1086 tractor. ‘“‘Our 1086 came equipped with radial tires, giving the tractor better than normal traction and, when we were given a chance to try duals, we were pleased with even more complete traction and less compaction. We were disappointed with the electronic instrument panel on the tractor, though. It gave incorrect readings and could not be adjusted. The dealer finally obtained a new panel for us.”

See this page at FARM SHOW →
Best Buy

Vermeer + 1 more

Terry Frommelt, Guttenberg, Iowa · Vol. 5, No. 6 (1981), p. 11

Terry Frommelt, Guttenberg, Iowa: ‘This is a super baler,” reports Terry about his Vermeer 605F round baler. ‘Most new equipment requires a percentage of warranty work but the only repair work I've done after custom-baling 1,500 bales is on one sealed bearing, a couple bolts in the pickup bar and I replaced three belts. In the first 1,000 bales, I didn't have a single problem.” He's not satisfied, however, with his Duracraft 6-in. bench vise." When you putan item in one side of the vise it does not tighten evenly in the jaws. When the jaws are tightened by hand only, using no extra leverage on the handle, the screw in the vise will jump a thread when it is almost tight.” Gilles Dehoog, Jr., Lynden, Wash.: “My ‘best buy’ is a model 698 Weed Eater,” says Gilles. “The gas motor has lots of power for its size. With the nylon line you can trim around buildings, fence lines or just anywhere. With the brush blade I've cut trees two inches in diameter. “Il also like my John Deere 2640 tractor. It’s small enough to scrape around the barn lot and, putting out 80 horsepower, it’s just right for field work. “My brother and I work together and another good buy is the John Deere 4440 he bought this spring. It's twice as much tractor as the 3020 (1968) he traded in but cost five times the $8,000 price our dad paid for the 3020. Dad, at 73 years of age, grew up with horses and it usually takes hima year before he tries out a new piece of equipment, but not this one. We had the 4440 only one week when he had to try it out.”

See this page at FARM SHOW →
Best Buy

John A. Grady, Downey, Idaho · Vol. 5, No. 6 (1981), p. 11

John A. Grady, Downey, Idaho: John likes his Wade Rain wheel line irrigation system. “It's built very sturdy with 5-in. aluminum pipe and easily moves across the hilly terrain on my farm. The dealer replaced at no charge all of the Rainbird heads, which were found to be defective a year after the purchase.” John reports some problems with his 1980 Ford F-100 pickup. ‘The steering pulled severely to the right. I had it examined, and supposedly corrected, three times. The third time was charged for an alignment and axle bending by the dealer who said the warranty did not cover steering defects. Since that, the truck now pulls left, although not as badly. Also, fuel economy is much less than the EPA estimate.”

See this page at FARM SHOW →
Best Buy

Michael Woodland, Paul, Idaho · Vol. 5, No. 6 (1981), p. 11

Michael Woodland, Paul, Idaho: His Miller portable welder and Alloway 12-row cultivator, are ‘best buys". “The Miller has been very dependable. It has enough capacity even for demanding jobs and makes a great backup generator when the power goes off. The Alloway has allowed me to get the cultivating done faster and do a better job than ever before. I really like the tunnel shields, even in our rocky conditions.”

See this page at FARM SHOW →
Best Buy

Honda

David Osbeck, Claremont, Minn · Vol. 5, No. 6 (1981), p. 11

David Osbeck, Claremont, Minn: “T bought my 750 Honda in 1975 and it now has 32,000 miles. I'm sure it has another 32,000 miles left to go,” says David, about his ‘best buy”. “I change oil and filter every 2,000 miles, It never sits in the winter with dirty oil in it, The only problem is that gas mileage could be better. I feel that 36 miles per gallon is rather low. But, having had no repair costs, it will be easy to choose my next cycle.”

See this page at FARM SHOW →
Worst Buy

John Deere

Ted A. Pekar, Granger, Tex · Vol. 5, No. 6 (1981), p. 11

Ted A. Pekar, Granger, Tex: Ted likes his John Deere cotton stripper. “We had our 30-in, row header and stripper delivered to us just before last year’s harvest. Now, after two seasons, only one bearing has needed replacing. Hardly any adjusting is ever necessary.” As ‘worst buy”, Ted nominates his ‘‘Wood's Brothers 320 Bat Wing shredder. After a lot of trouble, the company service people haven't shown up for 18 months, First the gear teeth and gear box fell apart for a cost of $1,200. After only one year, all the drive lines had to be replaced for another cost of several hundred. Truly a pile of junk.”

See this page at FARM SHOW →
Best Buy

Case + 1 more

Carrol Wrinkle, Ontario, Ore · Vol. 5, No. 6 (1981), p. 11

Carrol Wrinkle, Ontario, Ore: His two “best buys’ are his Ace Cultipacker and Case offset disk. ‘‘l bought the culti-packer from our local Ford dealer. It’s a good buy and works well in our heavy clay soil. Does well in clods and crust. Pulls either way — one side is regular and the other side grinds harder on clods. The Case disk really cuts, especially in straw and ground cover. It covers well, cuts deep and leaves little grooving in the field.”

See this page at FARM SHOW →
Best Buy

Robert Caissie, Moncton, New Brunswick · Vol. 5, No. 6 (1981), p. 11

Robert Caissie, Moncton, New Brunswick: ‘‘My new Belarus 420 “My Belarus 420 is one of the best buys I ever made. But I get poor service.” tractor is one of the best buys I ever made, but I get poor service around this part of the country. I'd like to know if all Belarus dealers are the same.” On the minus side, Robert notes that, ‘My 550 Cockshutt tractor is no good. In every way it is too costly, including fuel and parts.”

See this page at FARM SHOW →
Worst Buy

Donald Brotzman, Jasper, N.Y · Vol. 5, No. 6 (1981), p. 11

Donald Brotzman, Jasper, N.Y: Donald's best and worst buy are the same machine — his 1978 Chevrolet Impala. “It was good on gas and gave a very quiet ride but there were problems. The plastic parts cracked, the heater switch broke, and edge moldings were poor. It needed a new starter at 30,000 miles and a new radiator core at 35,000 miles, The anti-freeze from the factory turned acidic and ate up the core.”

See this page at FARM SHOW →
Best BuyWorst Buy

Massey Ferguson + 1 more

Gene C. Deckard, Sadler, Tex · Vol. 5, No. 6 (1981), p. 11

Gene C. Deckard, Sadler, Tex: Gene nominates his pair of Massey Ferguson model 33 grain drills as best buys. “I drilled 800 acres with only one stop —a broken roller chain. The drills are simple and have ample strength. “Another good buy was Dual herbicide, which did a great job controlling nutsedge and prickly sida, The 2% gallon plastic jugs are much easier to destroy than five gallon cans.” Gene adds that he's had some problems with his 750 Massey Ferguson combine. “It ran 1,000 plus acres the first season with only one stop. During wheat harvest this year it had 18 stops, including broken bell cranks, two bearings, four broken hydraulic lines alternator, voltage regulators and air conditioner problems. To be fair though, it cut 300 acres of milo without a stop. The capacity and grain sample is great and the machine is easy to set and operate.” (Continued on next page.) Best And Worst 1980 4-row International 87 black land (peat) planter is one of my ‘best buys’. The planter spaces the seed evenly and the seed plates and other adjustments on this planter were very easy to adjust to the desired setting’ Even though the planter is primarily for black land it works well in all types of soil. I did have a minor breakdown but the dealer had the parts on hand which were replaced free of charge with little lost time. “Another good buy was a 1980 4-row Dunham cultivator. liked the way it penetrates even the hardest ground, and its vibrating action to eliminate weeds. “One of my worst buys ever was a Bush Hog heavy duty offset disk. The scrapers did not do the job. The frame on the disk had a bow in it, right from the factory. This caused other problems because it wasn't made very durable. In the first week of use, the tongue pulled out and was rewelded by the dealer. The tongue pulled outa second time within one hour's use. This time, I welded the tongue back in place myself and put braces where they were needed. The tongue has held up ever since, The disc spacings were too close together and after using approximately $500 worth of parts to rework the spacings between the discs, now have a good piece of machinery.”

See this page at FARM SHOW →
Best Buy

Case + 1 more

D.H. Alexander, Brandon, Man · Vol. 5, No. 6 (1981), p. 12

D.H. Alexander, Brandon, Man: He likes his Wen electric chain saw. “ haven't used it much yet, but have had no trouble at all. It's very handy for cutting up firewood for the shop. Indoors it’s convenient as there are no exhaust fumes. “Also on the plus side, converted an old Case combine into a selfpropelled sprayer. It works quite well with two 200-gal. tanks and booms on it. Covers approximately 70 ft. with end nozzles. “I'm also pleased with my 18-ft. C.G.L.L. model 550 swather, Lays a real good swath and causes no trouble at all. The 200 Ford motor runs well and is easier on gas than the older model with the Wisconsin engine. The table is on a center pivot, does a good job of floating over stones and gullies, and is easy to control.”

See this page at FARM SHOW →
Best Buy

Chevrolet

Allan Lee, Hanska, Minn · Vol. 5, No. 6 (1981), p. 12

Allan Lee, Hanska, Minn: “After owning a foreign made compact pickup, I bought an ‘81 Chevrolet 1% ton 4-wheel drive with a 305 cu. in. engine. It gets 17 or 18 miles per gallon on trips and I really appreciate being able to carry three people in the cab, pull a trailer, haul moderate loads, and to ride in comfort again.”

See this page at FARM SHOW →
Best Buy

Greg Van Zanten, Colton, S. Dak · Vol. 5, No. 6 (1981), p. 12

Greg Van Zanten, Colton, S. Dak: Heading Greg’s ‘best buy” list is his “Knight LA-9 Litthe Auggie mixerblender-bunk feeder wagon, We use this mixer wagon 4 or 5 times a day, every day of the year. Breakdown time has been near zero. This is especially important with hungry cattle to feed, Mixes rations well and, with the scale, you know exactly what's going into the cattle. Well-built with heavy roller chains, pillow block bearings, page) and pintle chain throughout.” On the negative side, Greg notes that he's disappointed with his Koyker 85B 52-ft. pto grain auger “The auger worked beautifully for the first 10,000 bu. that went through it. Then, the pins that held the auger sections together dropped out, causing the flighting to bend and shearpins to break. Repairing meant disassembling the entire auger, fixing the pins and reassembling, which was an 8-hour job for two men. Koyker later changed the model to 85 “C" but wouldn't help me out on this one. traded it for a Feterl aneer.”

See this page at FARM SHOW →
Best Buy

Ford + 1 more

Joyce W. Miller, Independence, Kan · Vol. 5, No. 6 (1981), p. 12

Joyce W. Miller, Independence, Kan: “In 1979 I bought a Ford 2600 3-cylinder diesel tractor. in two ‘*A mechanic told me to turn the steering wheel when turning the key. It worked.” years, it has been beyond my expectations in dependability, amount of warranty work needed, fuel economy and its snappy engine. “In 1979 Lalso bought a 2640 John Deere tractor. It starts good when cold, has plenty of power but is the most frustrating tractor in my 42 years of owning tractors. First, the quick couplers on the cylinder hose popped out several times, shooting about one gallon of oil on the ground. [had to wire it together for 11 months before John Deere replaced the unit. “Then, the hose on the oil surge tank above the radiator split and, when oil hit the fan, it gave me an oil bath, Deere made a heavier hose but it took 15 months to get it. Another problem is that for the last year, after using the tractor fora few minutes, if] shut it off the starter would not turn the engine over. A mechanic told me to turn the steering wheel when turning the key. It works. “The final problem is that the hydraulic cylinder drops its load when cold but raises when warmed up, requiring constant adjustment on the lever,” explains Joyce.

See this page at FARM SHOW →
Best Buy

Earl Schoenhals, Shattuck, Okla · Vol. 5, No. 6 (1981), p. 12

Earl Schoenhals, Shattuck, Okla: “The ‘best buy’ I've made was my Owatonna Manufacturing Company 595 round baler which uses rollers instead of chains or belts to form bales. believe this is the most trouble-free baler on the market and also the fastest in the field,” says Earl.

See this page at FARM SHOW →
Best Buy

Allis-Chalmers

William E. Hinricks, Meridian, Idaho · Vol. 5, No. 6 (1981), p. 12

William E. Hinricks, Meridian, Idaho: William is disappointed with his electronic mouse control. “Its a Sonitron Cand is supposed to createa high pitch noise to discourage mice, Rather than chase them away, they nest right by it," he says. He's also displeased with “the new improved milker inflations from DeLaval, They cut everytime a cow kicks them on the floor. They were much better before they ‘improved’ thern.”’ On the plus side, Willam's happy with his Lincoln AC/DC welder, ‘We bought the welder because it has a 6,000 watt power plant as well as a welder. We use it to run the electric knife sharpener on our Fox forage harvester when we are away from any other power source. We're also happy with our Allis Chalmers 2550 15-ft, disk that has given us no trouble in 1% years. Our Kverneland 4-bottom, 2-way plow is also a good buy and has gone through rocks with no damage in 200 acres.”

See this page at FARM SHOW →
Worst Buy

Alan Aprill, Ann Arbor, Mich · Vol. 5, No. 6 (1981), p. 12

Alan Aprill, Ann Arbor, Mich: “My International 1420 Axial Flow combine is a real workhorse and performs better than I could imagine. It's a real asset to my operation.” About his “worst buy’, Alan says, “My experience with Mariner seed oats was far from good. They grow too tall and then lodge, making them hard to combine. Another bad buy isa 1470 Bush Hog disk. The transport wheels are too close to the front disc and it plugs in heavy corn stalks.”

See this page at FARM SHOW →
Best Buy

Oliver

Joseph Lee Winslow, Belvidere, S.C · Vol. 5, No. 6 (1981), p. 12

Joseph Lee Winslow, Belvidere, S.C: ‘I've had two sets of B.F. Goodrich tires on my tractor and have had trouble with both sets,’’ reports Joseph. The sidewalls on the first set broke after two years. The dealer paid half price on another set. After four years, am experiencing the same trouble with the sidewalls breaking. This time the dealer won't do anything about them. Both sets still had about % worth of tread left on them. “I'd have to nominate my 1755 Oliver tractor and my 1580 Lilliston peanut picker as ‘best buys’,” Joseph continues, ‘‘The 1755 is a good working tractor for the 86 horsepower range and, coupled with the 1580 peanut picker, does an excellent job picking peanuts. The over and under hydraulic shift works great to give a good range of speeds for varying conditions."

See this page at FARM SHOW →
Best Buy

Donald W. Parker, Apple Springs, Tex · Vol. 5, No. 6 (1981), p. 12

Donald W. Parker, Apple Springs, Tex: ‘An economical way to control hornflies,” says Donald, pleased with Extrin ear tags for livestock. ‘They really worked great for me this year. I only used them on 30 head this year but will put the tags on all my cows next year.” Donald's had trouble with his Vicon 7-ft,, 10-in, mower, ‘The gearbox went out after only about 100 acres of mowing. The dealer traded me another new Vicon. It did the same thing. The dealer was great, but this cost money and down time.”

See this page at FARM SHOW →
Best Buy

Alvin Goetz, Bluffton, Alberta · Vol. 5, No. 6 (1981), p. 12

Alvin Goetz, Bluffton, Alberta: “My most disappointing experience with farm machinery is just trying to repair farm machinery in general,” says Alvin. “Designing equipment for ease of repair seems to be too complicated for the so-called experts.”

See this page at FARM SHOW →
Best Buy

J. Allison Toner, Grand Falls, New Brunswick · Vol. 5, No. 6 (1981), p. 12

J. Allison Toner, Grand Falls, New Brunswick: He likes his Woods 990 grader. ‘This equipment has its own hydraulic cylinders and attaches to the 3-pt. with a float wheel behind it. » Ona 100 hp tractor it's more versatile than a small commercial road grader.”’ Tom Terwilliger, Eaton Rapids, Mich,; Tom's pleased with Impro health care products. ‘‘We use them for dairy herd health. We're pleased with their performance and appreciate not having to use withdrawal medications that cattle become immune to,”

See this page at FARM SHOW →
Best Buy

Bill Grier, Woodmore, Manitoba · Vol. 5, No. 6 (1981), p. 12

Bill Grier, Woodmore, Manitoba: “It's the cheapest tractor on the market and it’s easy on fuel,” says Bill, happy with his Belarus 610. “You just bring this tractor home and put it to work.”

See this page at FARM SHOW →
Best Buy

John Deere

Dale Berden, Snover, Mich · Vol. 5, No. 6 (1981), p. 12

Dale Berden, Snover, Mich: Dale's unhappy with his Glencoe W34DD field cultivator. “When we first got it, it wouldn't raise level. We had to put in new axles but it still is not perfect. Also, the frame has broken several times. The dealer and the company have been good in getting new parts but it should have been built better in the first place.” Dale's had good luck with his John Deere 4640 powershift tractor. ‘It has about 700 hours on it and the only time it's been in the shop was for a 100 hour check-up. I like the power shift very much for the sugarbeet harvester and our 16-row planter.”

See this page at FARM SHOW →
Best Buy

International Harvester + 1 more

Burl Eastman, Scio, Ore · Vol. 5, No. 6 (1981), p. 12

Burl Eastman, Scio, Ore: ‘We had trouble from the beginning with the scrapers,”’ says Burl, unhappy with his 315 International Culti-Mulcher. “They wouldn't stay adjusted and we had to completely redesign the scraper set-up, The smal] pins on the hydraulics which set the depth on the spring teeth are constantly breaking. The arbor bolt broke in two and we had a terrible time finding a replacement. It took three weeks and we probably still wouldn't have it if it wasn't for the diligence of one employee at our dealership.” On the plus side, Burl's happy with his International 1486 tractor and John Deere 3600 land plow. “The plow pulls easily, is easy to adjust, built sturdy and has good clearance. It is definitely one of my better buys. Once we rectified minor irritations on the tractor, we are well-satisfied. Has good fuel economy and the brake system is excellent.”

See this page at FARM SHOW →
Best Buy

White

Jerry Richter, Newell, lowa · Vol. 5, No. 6 (1981), p. 12

Jerry Richter, Newell, lowa: “‘If this planter was green, the others wouldn't have a chance," says Jerry, confident that the White 5100 planter he bought after planting last spring will turn into a ‘best buy’. ‘What sold me on it was the near perfect planting job I saw it do on several neighboring fields of corn and soybeans. Outstanding features include folding wings, very fast change from corn to soybeans, and very few moving parts.”

See this page at FARM SHOW →
Best Buy

Bert Feuz, Cokeville, Wy · Vol. 5, No. 6 (1981), p. 12

Bert Feuz, Cokeville, Wy: He's happy with his 450B Case Crawler equipped with a 6-way hydraulic dozer and ripper. ‘This is a super fast and highly versatile machine to operate and an extremely well-designed and built piece of equipment.”

See this page at FARM SHOW →