Real farmers rate what they bought, from FARM SHOW MagazineSubscribe  ·  Free issue  ·  Send us your Best or Worst Buy
Subscribe to FARM SHOW
Home › Issues › Vol. 19, No. 4 (1995)

Best & Worst Buys: FARM SHOW Vol. 19, No. 4 (1995)

65 reports from pages 14–16 · 60 Best Buys9 Worst Buys · See everything in this issue at FARM SHOW →

Best Buy

Daniel Krenzel, Cullman, Ala

Daniel Krenzel, Cullman, Ala · Vol. 19, No. 4 (1995), p. 14

Daniel Krenzel, Cullman, Ala.: “I bought my 197] Plymouth Duster with 318 cu, in, V-8 engine new, I installed an Allison electronic ignition system in 1976 and it has been in operation ever since with just two plug changes in 120,000 miles. I use Conklin metal base oil 10/30. At 106,000 miles, I replaced the head gaskets and the valves were good. The sleeves didn’t even have a ring groove. I closed up the engine and have continued to drive it until today, Runs great.”

See this page at FARM SHOW →
Best Buy

Case S-128 + 1 more

Robert Himmerich, Pena Blanca, N.M. · Vol. 19, No. 4 (1995), p. 14

Robert Himmerich, Pena Blanca, N.M.: Robert's “best buy” is a tillage tool he made out of a 1950's Case S-128 disk. 1ys “We replaced the rear disk gangs with a pair of 2 1/2-in. sq. toolbars which we fitted with 11 Allis-Chalmers field cultivator spring tines with twisted chisel points. They throw soil back toward the center of the disk. The center ridge is broken up by a straight chisel point. For less than $400 we now have an excellent piece of conservation tillage equipment. “My Vac-A-Way seed and grain cleaner/ grader is my worst buy. It doesn’t develop enough vacuum power to remove light material from the grain. To get acceptably clean seed we have to run grain through it at least three times. We had to reinforce the bagger-elevator in order to keep the sheet metal from collapsing onto the elevator belts and jamming them. For a little more money we could have bought a much better rig.”

See this page at FARM SHOW →
Best Buy

Bill DeRemer, Conneautville, Penn

Bill DeRemer, Conneautville, Penn · Vol. 19, No. 4 (1995), p. 14

Bill DeRemer, Conneautville, Penn.: “I'm disgusted with my Land Pride 3-pt. pto-driven tiller. looked at a dozen different 3-pt. pto-driven tillers before I bought it. I broke two blades and couldn't find replacements anywhere. Finally, a local dealer ordered four left hand and fourright hand blades, They're made in Italy and are nothing like the original ones that came with the machine. The only thing common to the two blades is the bolt hole pattern, Now [have to buy 10 more blades to match the eight I’ve already bought.”

See this page at FARM SHOW →
Best Buy

Ronald H

Ronald H. Schultz, Truman, Minn · Vol. 19, No. 4 (1995), p. 14

Ronald H. Schultz, Truman, Minn.: “My best buy is my 1993 Caterpillar Challenger 75C tractor equipped with 35-in, wide rubber tracks. The tracks reduce soil compaction, cause the tractor to ride smooth, and steer easily, resulting in much less fatigue at the end of a long day.” On the “worst buy” side, Ronald’s unhappy with his 1993 Hobart Beta Mig 250amp wire welder, “I’ve had problems with it ever since I bought it, It‘s rated to work on a 50-amp breaker, but it kicked out the 60-amp breaker I was using. I had to use an 80-amp breaker to make it work. I sent it back to the company under warranty on three occasions, but they couldn’ t find anything wrong with it. I also don’t like how the welder arcs - it fluctuates and is erratic. I’ve used several different brands of welders over the past 15 years. This is one of the worst.”

See this page at FARM SHOW →
Best Buy

Vermeer 505

Dwain W. Case, Wesson, Miss · Vol. 19, No. 4 (1995), p. 14

Dwain W. Case, Wesson, Miss.: “My 1992 Vermeer 505 round baler is the best and simplest baler on the market. It makes nice bales and is easy to operate. “My 1991 Fella 8-ft. mower is my worst buy. A bearing in the sicklebar went out, four oil seals in the gearbox failed, the lift arm pins broke off, and numerous welds broke, All of this happened during one hay season, The following year I bought a New Holland mower, love it.”

See this page at FARM SHOW →
Best Buy

Case

Thomas N. Johnson, Rossville, Tenn · Vol. 19, No. 4 (1995), p. 14

Thomas N. Johnson, Rossville, Tenn.: “It’s the best mower I’ve ever had,” says Thomas, owner of a Taylor Way 1500 15ft. hydraulic batwing rotary mower. “My new Case-TH 900 no-till planter is one of the best planters ever built. It does a good job planting under almost any conditions and doesn’t even need no-till coulters. It’s truly a fine row crop planter.”

See this page at FARM SHOW →
Worst Buy

Warren Stevenson, Lewis, Ind

Warren Stevenson, Lewis, Ind · Vol. 19, No. 4 (1995), p. 14

Warren Stevenson, Lewis, Ind.: “My Husky 18 hp 45-in. riding mower is my worst buy. The 7-in. blade on the left side of the mower is a joke. It doesn’t cut right. I think it was added to the 38-in. deck just to use up the available horsepower. I'll never buy another mower that has different size blades. I think three 15-in, blades would have worked much better.”

See this page at FARM SHOW →
Worst Buy

Earl Black, Vonore, Tenn

Earl Black, Vonore, Tenn · Vol. 19, No. 4 (1995), p. 14

Earl Black, Vonore, Tenn.: “My New Holland 411 discbine is my worst buy, A bearing went out which tore the blade apart. I had to replace the complete cutterbar at a cost of about $3,300. I did all the labor myself. Also, the rubber cover on the crimping rolls came apart and the dealer wouldn't pay for any of the repair cost.”

See this page at FARM SHOW →
Best BuyWorst Buy

John Deere + 1 more

Joseph Warren, Maple City, Kan · Vol. 19, No. 4 (1995), p. 14

Joseph Warren, Maple City, Kan.: “It drives like a dream,” says Joseph, pleased owner of a 1985 Pontiac Grand Prix. “It turns corners without skidding and the 6 cyl., 4.2-liter engine runs smooth, It has a lot of power and doesn't require much maintenance, I tuned it up at 45,000 miles and it still runs good even though it has 132,000 miles. It gets 24 mpg on the highway. “My worst buy is my Deere field cultivator. It's equipped with 6-in. sweeps and spring shanks with coil springs that break easily, The springs cost quite a bit and don’t last long. The arms on the wheels are held in place by copper bushings which wear out, “My New Holland 275 baler has trouble tying bales in dry, springy hay which pushes the strings off the knotter so it won't tie. The baler should come with gears so that the knotter can be speeded up to tie the knot before the plunger returns in those conditions, However, in normal hay conditions it ties good.”

See this page at FARM SHOW →
Best BuyWorst Buy

DeWalt 3/8in + 1 more

Richard D. Nemec, Midland, 8. Dak · Vol. 19, No. 4 (1995), p. 15

Richard D. Nemec, Midland, 8. Dak.: Richard's impressed with his DeWalt 3/8in. 110-volt electric drill. “It has a lot of torque and the chuck is made better than on most drills. Also, it has a double level that reads horizontally or vertically. “My Makita 12-volt 3/8-in. cordless drill is my worst buy. I couldn't keep it operating for more than a half hour without having to replace the battery. I sent it back to the service center but they said there was nothing wrong with it, I returned it and gota full refund.”

See this page at FARM SHOW →
Best Buy

John Deere 7200

Lloyd Jark, Stratford, S. Dak · Vol. 19, No. 4 (1995), p. 15

Lloyd Jark, Stratford, S. Dak.: A 1995 Deere 7200 tractor rates as Lloyd's “best buy”. “It handles easy and drives comfort“I couldn't keep it operating for more than a half hour without having to replace the battery.” ably, and the cab has excellent visibility. really like the 16-speed Power-Quad trans mission. It has clutch-free shifting from forward to reverse and offers the right speeds for my farming operation. It’s a real comfort to drive this tractor.”

See this page at FARM SHOW →
Best Buy

Karl Wangen, Soldiers Grove, Wis

Karl Wangen, Soldiers Grove, Wis · Vol. 19, No. 4 (1995), p. 15

Karl Wangen, Soldiers Grove, Wis.: Karl nominates his 1991 Claas Rollant 66 round baler as “best buy”. “It’s easy to operate and dependable. I’ ve used it to make over 1,600 bales with no problems other than replacing a few sets of pickup teeth. My only problem is that when I wanted to buy some extra splicer links to have on hand, I couldn't get them right away because the dealer had to order them.”

See this page at FARM SHOW →
Best Buy

Jack W

Jack W. Griffith, Arlington, Texas · Vol. 19, No. 4 (1995), p. 15

Jack W. Griffith, Arlington, Texas: “My best buy is my Belarus 400 tractor equipped with a 57 hp air-cooled engine. It uses 20-year-old technology but has a 20year-old price. My only complaint is that I wish the shuttle shift transmission was more convenient to use.”

See this page at FARM SHOW →
Best Buy

David John Egge, Ulster, Penn

David John Egge, Ulster, Penn · Vol. 19, No. 4 (1995), p. 15

David John Egge, Ulster, Penn.: David says Rohn steel cattle gates and panels head his “best buy” list. “They're absolutely the best gates on the market. They're made from heavy gauge steel pipe with excellent welding and fit. Each weld joint has its own weep hole which allows water to drain out in foul weather, The gates are hot dip galvanized after assembly is completed. They're built super strong in all areas including the hinge, latch, and the gate itself. Livestock can’t damage them. I don’t think I'll ever have to buy another gate again.” “My 1993 Diller round bale feeder wagons are also best buys. They're made from heavy gauge steel and have great workmanship. Up to three ,000-Ib. bales are placed in a bale basket over two troughs that catch loose hay below. The wagons have a low profile with slant bar cattle entries. Cattle don’t move around when they eat hay but instead pull it down from the basket, thereby preventing hay waste. Also, the wagon can be moved to prevent mud holes and manure build-up.”

See this page at FARM SHOW →
Best Buy

John Deere 4450

Jim Engel, Beatrice, Neb · Vol. 19, No. 4 (1995), p. 15

Jim Engel, Beatrice, Neb.: Jim describes his 1985 Deere 4450 tractor as “a lemon that’s painted green”. “It’s the most undependable tractor we have on our farm. The first year we had it one of the rear wheel rims cracked at the bead form line. It doesn't come close in quality to the 4010, 4020, 4430, or 4440 models that we've used in the past. Our 4020 equipped with a front-end loader has 8,900 hours on it with only normal maintenance, and our 4440 has 5,400 hours on it and is a real gem. The list of other repairs is endless.”

See this page at FARM SHOW →
Best BuyWorst Buy

Ford F-150 + 1 more

Rick Wallace, Shelburne, Ontario · Vol. 19, No. 4 (1995), p. 15

Rick Wallace, Shelburne, Ontario: “My Posi Lock gear puller is an excellent product. It's well made and is a must for any farm or business. “Pederson vise grips are a time-tested, superior tool. They work better than any copy cat model and deserve an award. (Peterson Mfg., 108 S, Pear, DeWitt, Neb. 68341 ph 402 683-2325). “On the worst buy side nominate my 199] Ford F-150 pickup. The paint is falling off it and the dealer won't help. I've written directly to the company with no results. [even sent them a copy of the story FARM SHOW published regarding paint peeling off Ford pickups. I'll never buy another Ford again.”

See this page at FARM SHOW →
Best Buy

John Deere 8960 + 1 more

Joel Lust, Marion, Ohio · Vol. 19, No. 4 (1995), p. 15

Joel Lust, Marion, Ohio: Joe! likes his 1991 Deere 8960 4-WD tractor. “We haven't had any real problems with it after 1,300 hours. It has a lot of power and drives comfortably. Maintenance is simple and quick, It replaced an International 4586 4-WD tractor and is superior in every measurable way. It was like going from a Subaru to a Cadillac. “My 1990 Sunflower 5331 36-ft. field cultivator is my worst buy. The biggest problem is that we've never been able to get it to work evenly in the ground over the entire width of the implement. One side of the center section sucks down which pulls the other side up. We’ ve tried everything we could think of, including cylinder stop combinations, measurements, adjustments, etc., with no luck. Our dealer gave us a kit to solve the problem but it didn’t help. It must be a design flaw because a neighbor had the same problem, It’s a shame that it won't pull evenly because it’s built heavy.”

See this page at FARM SHOW →
Best Buy

International Harvester

Dan Wasson, Selden, Kan · Vol. 19, No. 4 (1995), p. 15

Dan Wasson, Selden, Kan.: Dan’s “best buy of all time” is his 1979 International “It's big enough to handle all my hay raking, yet compact enough for routine chores around the farm.” 1086 tractor equipped with a Farmhand 235 front-end loader. “The tractor and loader work great together. We've used it practically every day and it has never refused to start. It has 7,800 hours. We've installed several new clutches and a torque amplifier, and at 6,000 hours we had to replace the oil pump and a rod and main bearing. The left hand gearshift makes it a perfect loader-tractor,”

See this page at FARM SHOW →
Worst Buy

Mark C

Mark C. Alberts, Gothenburg, Neb · Vol. 19, No. 4 (1995), p. 15

Mark C. Alberts, Gothenburg, Neb.: “Our 1989 A & L 556 grain cart speeds up haryest and also reduces wear and tear on trucks and our combine. We can harvest 30 percent more corn per day with it. New models have the auger at the corner for better visibility. I think it’s an improvement.” On the negative side, Mark had problems with DeKalb DK 554 seed corn. “Even though the bags were labeled for 95 percent germination, we had only about a half or 2/3 stand. Other corn planted on either side of this hybrid had perfect stands so the problem wasn’t anything mechanical. should have replanted it, but it was getting late in the season. If this wasn’t bad enough, the attitude of the company stunk. They came out to our farm and agreed there was a problem with the seed and that they would make it right after we were able to measure yields. Well, that fall the district man came out with the dealer, Yields fell way short. However, the company said there was nothing they could do about it. My landlord wasn't too impressed.”

See this page at FARM SHOW →
Best Buy

International Harvester

Carl Van Zee, Russellville, Kent · Vol. 19, No. 4 (1995), p. 15

Carl Van Zee, Russellville, Kent.: “We're pleased with our International *‘Captivator’ electric fence controllers (American Farm Works, Rochester, Minn.). It’s nearly impossible to short them out even when they're completely covered with weeds or grass, We've even had tree limbs holding the wire down to the ground and they still worked. We use only one light barbed wire on our electric fences. Once cattle get a shock they leave the fence alone. Saves hours that would otherwise be spent keeping fence rows clean.”

See this page at FARM SHOW →
Best Buy

Tim Rott, Ashley, N

Tim Rott, Ashley, N. Dak · Vol. 19, No. 4 (1995), p. 15

Tim Rott, Ashley, N. Dak.: Tim likes Andersen low-energy argon-filled windows. “I bought seven windows as well as a patio door for an addition we made to our house last year. They're so efficient that the sun is able to heat the room during the day, even on cold days. No drafts at all.”

See this page at FARM SHOW →
Worst Buy

Chevrolet S-10

Steve Hoke, Walkersville, Md · Vol. 19, No. 4 (1995), p. 15

Steve Hoke, Walkersville, Md.: “My worst buy is my Chevrolet S-10 Blazer. The dealer-installed 5-speed manual transmission lasted only about 9,000 miles. When I tried to find out why it went out with so few miles on it, all I got from the company was lip service. My Blazer is now on its second engine and third transmission. Why can’t we buy quality-made products in this country? If I'd have bought a Landrover I'd have spent about the same money, but I'd have paid it up front instead of being nickeled and dimed to death because of inferior parts.”

See this page at FARM SHOW →
Best Buy

Honda

David Miller, Red Lake Falls, Minn · Vol. 19, No. 4 (1995), p. 15

David Miller, Red Lake Falls, Minn.: David's impressed with his 1995 Honda Foreman 400ce 4-WD ATY. “It has excellent traction and low-end torque and shifts much easier than previous ATV’s I've owned, It has a shorter turning radius and steers easier than 2-WD ATV's. It’s a joy to drive and reduces operator fatigue.”

See this page at FARM SHOW →
Best Buy

Bobcat 440B

Glenn F. Speer, Franklin, Penn · Vol. 19, No. 4 (1995), p. 15

Glenn F. Speer, Franklin, Penn.: “My best buy is my Bobcat 440B skid steer loader that I bought used two years ago. It has a lot of hydraulic lift for a small loader, I use it for cleaning hog pens, removing rocks from plowed fields, and plowing snow. also use it to move hogs with my own shop-built hog loading crate. One side of the crate has attachments to fit the loader arms on the skid steer loader. Tthe other side has fittings to fit the 3-pt. hitch on our tractor. Each side of the crate has a sliding end board for loading and unloading hogs. I used angle iron to make the frame and welded hog wire panels to the sides and top of it. I used 5/8-in. plywood to make the floor and end boards. Roscoe Speer and Chris Weber of Dempseytown, Penn., helped me build it.”

See this page at FARM SHOW →
Best Buy

Chevrolet 4-WD + 1 more

Donald Ballagh, North Rose, N.Y · Vol. 19, No. 4 (1995), p. 16

Donald Ballagh, North Rose, N.Y. Donald liked his 1991 Chevrolet 4-WD Silverado with 350 cu. in diesel and extended cab so much, he ordered a “95 with the same options. “My 1991 Silverado has 120,000 miles on it and all it has ever needed was routine maintenance. It has the most leg room in both the front and rear seats of any pickup I've ever been in. It’s got a gross vehicle weight of 6,600 Ibs., but easily hauls 4,000 Ibs, in the bed withouta lot of sagging. Mileage is good - about 16 mpg - and she’s a good looker as well.” “It has the most leg room in both the front and rear seats of any pickup I've ever been in.” Michael Burke, Dover Centre, Ontario: Michael's generally well satisfied with the Toyota extended cab pickup he purchased new in 1991. He’s had no problems with it in over 60,000 miles, he reports. However, he says two things need improving. “Fuel economy needs to be improved drastically. Also, it needs a slightly larger engine, at least up to a 2.8 liter.”

See this page at FARM SHOW →
Best Buy

Ram + 2 more

Duane E. Haney, Chenoa, Ill. · Vol. 19, No. 4 (1995), p. 16

Duane E. Haney, Chenoa, IIl.: “My 1994 Dodge Ram 2500 4-WD rides and drives better than my Mercury station wagon, It has ample power to pull a 31-ft. Sth wheel camper weighing over 5 tons empty, My only criticism is that when I down-shift out of cruise control, it jumps down two gears, then quickly up one. Chrysler should just leave the cruise control off altogether.”

See this page at FARM SHOW →
Best Buy

GMC 3500 + 4 more

Joseph Swennen, Bedford, Quebec · Vol. 19, No. 4 (1995), p. 16

Joseph Swennen, Bedford, Quebec: Joseph likes his 1993 GMC 3500 1-ton 4WD pickup equipped with a 6.5 liter turbo diesel engine. “Neither Ford nor Dodge could offer me a I-ton pickup that rides as smooth as my GMC.” Robert D. Campbell, Eagle Grove, Iowa; “My 1992 Chevrolet K-10 with 6,2 liter diesel engine gets up to 24 mpg and gives an excellent ride. I've got 33,000 trouble-free miles on it. It uses no oil.”

See this page at FARM SHOW →
Best Buy

Ram

Eric E. Elvin, Readfield, Maine · Vol. 19, No. 4 (1995), p. 16

Eric E. Elvin, Readfield, Maine: Eric tr] ners Nominate wants Dodge to take back his 1991 Dodge Dakota pickup, “They should melt it down and start all over, I'm only getting 13 mpg, even after a $325 dealer tune-up. The power windows don’t work and a tall person can’t see out of the tinted glass.”

See this page at FARM SHOW →
Best Buy

Ford F-350

John Wayne Nagy, Hempstead, Texas · Vol. 19, No. 4 (1995), p. 16

John Wayne Nagy, Hempstead, Texas: The “most perfect truck ever built,” John says, is the 199] Ford F-350 dually pickup equipped with 7.3 liter diesel engine and automatic transmission with overdrive. “T've put 100,000 miles on it and have only had to replace one power door lock. I got 70,000 miles out of the first set of tires. I can get 10 mpg pulling 12,000 to 15,000 Ibs. and 20 mpg on the highway.”

See this page at FARM SHOW →
Best Buy

Ram

Reno Warkentin, Blossom, Texas · Vol. 19, No. 4 (1995), p. 16

Reno Warkentin, Blossom, Texas: Reno’s 1994 3/4-ton Dodge diesel gives him an exceptional ride, but there are a few creature inconveniences, too, “Every time you try to belt yourself in, you push the other seat belt under the seat. It's impossible to buckle up with one hand. Also, the power door locks are located poorly, I'm constantly locking myself out of my truck by accidentally brushing against the lock as I get out.”

See this page at FARM SHOW →
Best Buy

Chevrolet

Dwight R. Robinson, Kansas, Hll · Vol. 19, No. 4 (1995), p. 16

Dwight R. Robinson, Kansas, Hll.: “I love my 1993 Chevrolet Silverado 2500 HD 4-WD pickup with 5.7 liter engine and 5-speed transmission. It averages about 14 mpg and rides like a 1/2-ton pickup, I pull 375-bu. wagons with it all fall and ammonia and seed wagons with it all spring because I don’t have a 2-ton truck on my 1,000-acre grain farm. I just bought a gooseneck trailer to pull with this truck.”

See this page at FARM SHOW →
Best Buy

Ram + 2 more

Anthony Ivey, Scott City, Kan · Vol. 19, No. 4 (1995), p. 16

Anthony Ivey, Scott City, Kan.; Anthony traded his 1988 Dodge Ram 50 with 116,000 trouble-free miles for a new 1993 Dodge D250 with Cummins diesel engine and club cab, He's equally as pleased with the 1993 Dodge as he was with the ‘88 he had before. “It’s got 17,000 miles on it with no trouble yet. It gets 28 mpg and has all the power I could ever hope for. It starts great on even the coldest winter mornings. The only fault I can find is with a poorquality paint job. The paint chips too easily.”

See this page at FARM SHOW →
Best Buy

Ford 1/2-ton

Chris Shauer, Ottawa, Kan · Vol. 19, No. 4 (1995), p. 16

Chris Shauer, Ottawa, Kan.: “Our best all-time pickup was a 1966 Ford 1/2-ton F-100 with 352 cu. in. V8 engine and club cab. My father purchased it in 1972 with 40,000 miles on it. He overhauled the engine at 100,000 miles after years of hauling up everything on the farm, We've gotten 23 years of service out of this pickup. It looks as great today as the day dad bought it. It’s now got 270,000 miles on it and I suspect it'll run many more before we retire it.”

See this page at FARM SHOW →
Best Buy

Ford

Don Rich, Oxford, Conn · Vol. 19, No. 4 (1995), p. 16

Don Rich, Oxford, Conn.; Don's favorite pickup is his 1994 Ford Super Duty 4 Best, Worst P WD equipped with a 460 cu. in, engine and 5-speed transmission with 2-speed auxiliary transmission. “It's more powerful than any other pickup I've ever driven, It's fuel efficient with the auxiliary transmission, which helps make it the best vehicle I’ve ever used for towing. My only complaint is that wish Ford would offer a black interior.”

See this page at FARM SHOW →
Best Buy

Ford + 1 more

Barbara Gattis, Cedar Creek, Texas · Vol. 19, No. 4 (1995), p. 16

Barbara Gattis, Cedar Creek, Texas: “We've gotten 23 years of service out of this pickup. It looks as great today as the day my dad bought it.” “My 1993 -ton Ford pickup equipped with a 7.3 liter diesel engine has been nothing but trouble. The steering system is a problem and it has no pulling power. I'm dissatisfied with almost everything about it. On the other hand, my 9-year-old Chevrolet pickup has tons of miles on it and I’ve never had one major problem with it.”

See this page at FARM SHOW →
Best BuyWorst Buy

Ford F-350 + 1 more

Gary Bruning, Ellsworth, Kan · Vol. 19, No. 4 (1995), p. 16

Gary Bruning, Ellsworth, Kan.: Gary's disappointed with his 1991 Ford F-350 4WD equipped with 7.3 liter diesel engine as compared with the 1984 Ford F-250 4WD. “Mileage isn’t nearly as good as with my ‘84, which had a 6.9 liter diesel. It's doggy and doesn’t start as easily when it's cold either,” Al Plumleg, Crown Point, Ind. “I'm absolutely 100 percent satisfied with my 1994 GM Sierra Z-71 4-WD with extended cab. It's roomy, powerful enough to haul big loads, and looks great. Plus, the dealer has been pretty good about service. I bought it 13 months ago and have put 42,000 miles on it. It hasn't missed a day of work.”

See this page at FARM SHOW →
Best Buy

GMC

K.M. Wise, Rockyford, Alberta · Vol. 19, No. 4 (1995), p. 16

K.M. Wise, Rockyford, Alberta: “I’m well satisfied with my 1992 GM Yukon, except for their ‘chip guard’ paint which doesn’t guard.- it chips. GMC, Canada, didn’t have the courtesy to respond to my letter of complaint. My dealer was told by the company it wasn’t covered by warranty. I've been a GM owner for over 30 years and have never had a problem as frustrating as this before.”

See this page at FARM SHOW →
Best Buy

Ram 250

Clarence J. Wiebe, Rush Lake, Sask. · Vol. 19, No. 4 (1995), p. 16

Clarence J. Wiebe, Rush Lake, Sask.: “My all-time best pickup is a 1952 THC L120 my father bought new and I’ve now used for about 15 years. It delivers consistently excellent performance - starting, ‘ickups power, handling, and fuel efficiency. The body is still a lot more solid than a lot of trucks that are 40 years newer. Even the doors still work great “As for newer trucks, I like my 1992 Dodge 250 LE 4-WD equipped with turbocharged diesel engine and 3-speed transmission. It’s exceptionally fuel efficient, has great power, and great interior and exterior design. It also starts excellentin cold weather. I've heard a lot of people say they have trouble with paint, but so far I’ve had no problems.”

See this page at FARM SHOW →
Best Buy

Ford F-350 + 1 more

C. Sherman Allen, Conneaut Lake, Pa. · Vol. 19, No. 4 (1995), p. 16

C. Sherman Allen, Conneaut Lake, Pa.: He’s had a problem with the 1993 Ford F-350 equipped with 7.3 liter diesel “Tt was only two years old when the paint peeled off the top and one fender.” engine and 5-speed transmission he bought new - and the extended service plan he bought for $1,545. He's contacted the Ford Motor Company of Ohio, his local Better Business Bureau, and the Pennsylvania attorney general's office about it. “The problem was that last May, a rod that fastens to the clutch pedal broke. I soon discovered that the part could not be purchased separately, but only with the clutch hydraulic sleeve cylinder and reservoir. And the repair was not covered by my extended service plan, “First, this is utterly ridiculous to have to pay $65.48 or more when all I need is this rod. Also, the part did not wear out, it suddenly broke into three pieces, which could be a safety concern for Ford since owners might not be able to stop their trucks in time if this rod breaks. Why isn’t . this repair covered under my extended war) ranty program?”

See this page at FARM SHOW →
Best Buy

Ram

Lawrence Kupchinski, Buchanan, Sask · Vol. 19, No. 4 (1995), p. 16

Lawrence Kupchinski, Buchanan, Sask.: “My 1993 Dodge Dakota 4-WD is what it is because of torsion bar front suspension, That must be good if GM copied it the year after Dodge came out with it. This is my second Dakota and I never looked at another make when I bought it. Fuel economy could be better, though.”

See this page at FARM SHOW →