Warren E. Jones, Woodston, Kan.: “There were no results. I honestly believe that if a dog had urinated on the field it would have done as much good,"’ says Warren, disappointed with Agri Spon soil innoculant.
Best & Worst Buys: FARM SHOW Vol. 7, No. 1 (1983)
61 reports from pages 10–13 · 54 Best Buys14 Worst Buys · See everything in this issue at FARM SHOW →
Ford
Norris Lawson, Yorktown, Tex.: “It's disgraceful to put Henry Ford's name on such junk," says Norris, upset with his 1982 Ford pickup. ‘‘T was told it would get up to 15 mpg, but I've never been able to get more than 13% mpg after 12,500 miles. Pulling atrailer, 1 get about 64% mpg."
John J. Beitel, Stayton, Ore.: Heading his ‘‘worst buy” list are his Micro-Max rotary spray nozzles. “These rotary nozzles haven't lived up to expectations. We used them with Roundup and Basagran. They seem to be more affected by wind than conventional nozzles and, when there is much growth atall, they don't provide the necessary penetration.”
Ford + 2 more
Oland McCain, Laurel Hill, Fla.: “We've had very disappointing experiences with Ford hay equipment. It's built lighter and not as well as Deere or New Holland. Would not recommend it to anyone," says Oland. On the plus side, he’s had good luck with his Kuhn disc mower and Butler Agri-building. “The mower cuts very clean through even thick coastal Bermuda grass, even when the grass is wet. Appears to be well engineered and built.”’
Case
Leo Bottoms, Dumas, Ark.: “My Hustler rice levee sprayer would be my worst buy,” says Leo. “The engine failed, we had repeated clutchvariable speed pulley failures and wheel drive chain breakage within the first year. The steering clutches are oversensitive to the point that you can't operate them smoothly enough to prevent overstress to the machine and operator alike. A hydrostatic drive system would make it a much nicer operating machine.” Heading his “best buy" list is his 4890 Case 4-wheel drive tractor. “Plenty of power, easy to handle, comfortable, and has plenty of hydraulic capacity to handle my 12 and 14 cu. yd. scrapers.”
Case
John Eisses, Stroud, Ont.: ‘This all happened with less than 500 hours on the tractor,’ says John, disap pointed with his 'tworst buy’ Case 2090 tractor, “It’s nice to handle but the pto clutch went out twice. Then the transmission had to be taken apart, it needed a new battery and the electrical system wouldn't work right. The dealer did give us a tractor to use when ours was in for repairs.” John likes his Honda ATC 110 allterrain bike and his 3,000 gal. Husky manure tank. ‘Even our 6-year-old can start itand driveit,” he says about the bike. “It’s handy to check fences, chase cows and check crops. The manure tank pulls easy and the orbit motor on the fan makes it real nice to spread with.”
International Harvester
Kenneth F. Stuhr, Petersburg, Neb: He's pleased with his International 605 cu. in. irrigation motor and a Reinke Alumigator III center pivot. “ hooked the 605 motor up to natural gas, started it and in two years have had no problems. It's never failed to start. The Alumigator, after initial startup problems, has performed great. It's equipped with Senninger 6° nozzles at 60 psi, which give even distribution with little drift. “Another best buy is our 371 Melroe Bobcat bought in 1975. It has over 900 hours with just regular maintenance. It has done everything from loading manure and construction work, to digging underground plenums for Behlen bins, A really well-built machine.”
Ford
Glenn Wollweber, Ford, Wash.: “Our next tractors will be Fords, too," says Glenn, pleased with his Ford 5000 and 3000 tractors. ‘‘We have had no trouble with either one and they use 20% less fuel than other makes. My neighbors can’t believe how easy our Fords start in cold weather. They haven't needed any repairs.”’
White + 1 more
Lorne Fuller, Calgary, Alta.: ‘I had just started to combine with my ptodriven pull-type combine when an internal shaft broke on the tractor. Exactly five weeks later, the dealer got the tractor fixed,” says Lorne, disappointed with his White 135 tractor. “The company representative, the dealer and service people all had different excuses for the delay. never brought the tractor home but traded it off for a Case 2390, which is my best buy. “It's a bitrough riding at times due to the short wheel base but the cab is quiet. Visibility is good except that it’s hard to see the drawbar for hookups. Has performed every job well.”
International Harvester
W. Lee Smith, Parker, Kan.: “My 1086 International tractor was delivered with no hydraulics and a bad noise in the back end. The dealer came and took it to his shop and separated it into three sections. They brought it back with the same noise and no hydraulics. Took it back to the shop and called the field serviceman in Kansas City. He came to the dealer’s shop and found 2 loose bolts, an O-ring out, and metal ina reiief valve in the back end! Then the throw-out bearing went out. [In replacing it, they lost the freon out of the air conditioner and charged me $50 to recharge it. Most of the work was under warranty but, since bought the tractor, ithas been in the shop 54 days with $800 of expenses in less than 800 hours. Now that the bugs are out, the tractor runs very good, Mos! trou bles were factory «vrors.”
Massey Ferguson
Douglas J. Johnson, Sidne,. Mont.: “The harrow sections start jumping when working fields on an angle, and sometimes on feve! ground, and won't quit until stop or slow way down. I've made all adjustments suggested by the factory but it hasn't helped,” says Douglas, about his Herman 67-ft. Culti-Harrow. On the plus side, he’s happy with his 1981 4880 Massey Ferguson 4wheel drive tractor, “The 3-speed on the go shifting of the Powershift transmission allows me to tackle the toughest hills without stopping. It has excellent traction and is very quiet.”
Chevrolet
Doyle D. Thomas, Corydon, lowa: “It cuts and windrows hay in one pass at 6 to 8 mph. Trouble free and very few moving parts. We bale hay after curing and never have to rake, which saves quite a bit of time,” Doyle reports about his MC 12-ft. rotary scythe. He had trouble with his new ¥2-ton Chevy 4-wheel drive 305 V-8 pickup. “First, it had to have a new set of shocks in less than 1,000 miles so it would handle right. The pickup didn't have any power and ran so rough that it changed gears at the least little exertion. It had a faulty oil pump so I had to replace the rod bearings and put new rings on one cylinder that was pumping oil, adding one quart every 300 miles. It took four or five trips to the service department and 20,000 miles before I finally got the truck to run like it should. It listed new for $10,700 — I should havea right to expect more for this price.”
Carroll Cabelka, Yale, Iowa: ‘1 used it on all my cornstalk ground last spring with excellent results. [t's built rugged, rocks don’t hurt it although it needs some scraper changes," says Carroll, pleased with his older model Deere TW 14-fv. plowing disk.
International Harvester
Loren Krause, Bemis, S. Dak.: On the “best buy” side, Loren nominates his International 1066 tractor bought used. “It has lots of power, and I find it will do a lot of work for the fuel it uses. It takes 5 gal. fuel per hour pulling a 2-row chopper and about 6 gal. per hour pulling an 18% ft. digger at 5% mph.”
John Deere
Paul W. Humphrey, Boonville, Mo: “Your magazine doesn't have enough space to list all the problems we've had with this car. If Chrysler builds all their products like this one, it’s little wonder they are nearly out of business,’’ says Paul, about his “worst buy’’ 1980 Chrysler New Yorker, On the plus side, he adds that, “We're pleased with our 8300 Deere grain/soybean drill. On the 900 acres of beans and wheat we planted last year, we had perfect stands. Depth control and metering capabilities are great.” Benton M. Trundle, Jr., Sevierville, Tenn.: His ‘‘best buy” is a 1981 GMC C6P heavy duty % ton pickup, “This truck has performed very well for me. It rides as comfortably as a car and drives well on long trips. I purchased a lifting tailgate for it that also performs well. It sure saves a lot of lifting of drums and equipment.” “Another good buy is a liquid fertilizer applicator from R.M. Distributors of Vail, lowa, for my 4-row corn planter. At under $300, it adapts to any planter and can apply as little as 2 gal. on up per acre. My Deere Backpack Blower was also a good buy.”
Francis Schaefers, Garnavillo, Iowa: “One of my best buys is my Porta Scale which first read about in from WBF Industries, Box 207, Elkader, Iowa. It's well-built and, at $225, it’s reasonably priced. By knowing when our hogs are at the proper weight, this scale pays for itself,” says Francis.
Emil A. Miller, Stafford Springs, Conn: ‘‘There should be a law against shipping them into the country.” says Emil, upset with his Jonsereds chainsaw. ‘This saw’s muffler is up front above the chain and bar, causing the motor to heat up. From “There should be a law against shipping them into the country.” the day purchased it, it never ran right. The dealer didn't try to straighten out the problem but said the saw was no good and offered me $150 for it when I'd paid $319, A call to the distributor was of no help. My saw was taken to four repair shops and the result was always the same. It works good at the shop but when it is put to work, it will not run more than 15 min. without cutting out. I changed the location of the gas vent from over the chain sprocket to the left of the gas trigger. This helped in that I can now use the saw. However, with the muffler in front over the chain and bars, the saw heats up and cuts out. One can only use this saw al the North Pole.”
Philip Muri, Central Butte, Sask.: He names his 1982 Lada Niva 1600 full-time 4 by 4 Russian import as “best buy". ‘It’s comfortable, economical at 30 mpg, and will go almost anywhere with Positraction on the rear wheels. The metal is about twice the gauge of Japanese cars. It’s sort of a back to the basics vehicle with nothing electronic. Comes with tire irons, metric tools, crank and manual choke.” His ‘worst buy" is his Lady Kenmore Corning top electric stove. “If anything overflows it runs between the two glasses on the oven door. The oven thermostat is unpredictable. If the oven is on, it interferes with radio and TV. The oven seal has been replaced twice. The meat probe worked for a very short time. Dealer will not make house calls."
Massey Ferguson
Russell Carter, Evening Shade, Ark: My “best buy" would have to be my 1440 Massey Ferguson hay baler. It bales a good tight bale and will bale about anything you would put in it. I have baled chunks and rocks with it and it starts a bale very easily."
Vermeer + 2 more
Jack Bonnette, Marietta, Ohio: “We looked closely at several round balers and were most impressed with the quality and ruggedness of this baler,” says Jack, about his Vermeer 504G baler. ‘‘When we first baled with the machine we found it was simple to handle and it operated as if we had used it before. Our hay is of excellent quality and our cows eat all of it. “Another good buy was our Deere 1207 mower-conditioner. We used it last summer and have only had to sharpen the sickle so far. Runs extremely quiet and is easily transported from one farm to another.” On the negative side, Jack's disappointed with replacement parts for his International tractor. “We spenta large sum of money and down time to install a new torque amplifier system in our International and it lasted approximately 50 hrs. before going out because of bad bearings.
Carl Wade, Washington, Ind.: “This grain cart is a new model but the company obviously tested it well before putting it on the market,"’ reports Carl, pleased with his ‘‘best buy” Killbros 600-bu. grain cart. “It's handled with ease by 24.5 - 32 tires. The unloading auger is tall enough to reach any truck any modern combine will dump into and the flow control gates unload any moisture grain at maximum speed, After running 1,000 acres through it last fall, we have not found one stress crack in the frame. We are very pleased and would not trade it for any cart on the market.”
Duane Filbert, Brownell, Kan.: One of his “best buys ever’’ is his 1979 Ford Courier pickup. “It’s the best put together pickup I’ve ever had. It has 66,000 miles now and only $12.50 in repairs. Excellent gas mileage and has good power with a “It’s the best put together pickup I’ve ever had.” 2.3 liter motor. We use it on the farm to feed cattle and chase after parts.”
GMC
Mark Tomazin, Valley Grove, W. Va: “This is a definite lemon,” says Mark, unhappy with a 1979 Jeep Cherokee S. “It was towed to the dealer 30 days after purchase with a cracked flywheel. It’s been downhill ever since. We spent $800 to keep it running last year. A weld on the front fender broke yesterday and the front fender and door were dented, resulting in another $200 plus bill. It’s junk,” On the positive side, he’s happy with his 1979 GMC % ton pickup. “It's smooth riding and has a very comfortable interior. In 4 years, it's only needed routine maintenance.
John Ploehn, Antwerp, N.Y.: He's had problems with his De Laval automatic washer. ‘‘The unit has problem solenoids. They are not moisture proof and, as there is a lot of moisture in the immediate area, they short out every 4 or 5 months. They are not cheap to replace, either."
Phyllis Howell, Bradford, N.Y.: “We get more and more dissatisfied with the 1979 Oldsmobile Cutlass diesel automobile that we bought new," says Phyllis. ‘‘While it was still under warranty, it developed a prob lem with the injector so it wouldn't always start. The dealer took off that pump and put ona rebuilt old pump. Since then, the car has rarely started well. We're always wearing down batteries, trying to get mechanics to fix it, and so on. We've put a fortune into that pump alone — about $1,200."
Allis-Chalmers + 1 more
Bill Short, Hamilton, Mo.: “Our worst buy has been our new Allis Chalmers disc as it seems to require an eternal supply of bearings all over the disc. Our all-time best buy has been our Farmall “H” which is easily serviced. We added a 3-pt. hitch and two-way hydraulic controls. If International would continue to build tractors as they built them then, they wouldn't be in their financial troubles now."
John Deere
LeRoy Fulk, Assumption, IIL: “We've had good luck with two John Deere 7720 combines purchased in 1981. Plenty of capacity and the cabs are quiet. Other than daily maintenance and adjusting we have had very little down time. This is our second pair of Deere combines. We have a good John Deere dealer for parts and service. No comparison to the service and parts on previous makes of combines.”
Doug Pevestorf, Coon Rapids, lowa: “Our best buy is our Bryan Furnace from Bryan Furnace Works, Bryan, Texas that I read about in 60,000 btu residential woodfired furnace goes outside the home and requires no modification to the house. A very well-engineered product. We can finally get our house warm without a lot of fuel. The only bad part is going outside to load it in 80° below zero weather.”
Yamaha + 1 more
Marv Andrijeski, McCook, Neb.: “Couldn't farm without one,” says Marv, happy with his Yamaha 200 3-wheeler. “It's especially handy for checking irrigation. We're also pleased with our 4400 Deere combine and our 4430 Deere tractor, We bought them both used and haven't had any major trouble with either one.”
Marcel Lambert, St. Claude, Manitoba: “It has 92,000 miles and all I've done, besides replacing the water pump and shocks, is general maintenance. It still runs like new and that's country driving at its best,”’ says Marcel, pleased with his 1974 Mercury Montego MX.
Allis-Chalmers
Herbert Eichman, Rush Colo.: ‘My worst buy is a 7020 Allis Chalmers tractor with power shift transmission. It will hardly pull itself in reverse and it is hard to shift between ranges. It will not start in cold weather even when it is plugged in, unless I put it inside and cover the engine with a blanket. It uses much more fuel than my old XT 190, I have no complaint with the dealer. He has tried everything to fix it, even putting different pistons in it.”
Ford
Sam Kleinsasser, Moose Jaw, Sask: “If you don’t spend 1 hour doing maintenance on it three times a day, it won't perform," says Sam, disappointed with his 36-ft. Anderson rod weeder. "We still have it and it ‘“Best’”’ and ‘‘' gives nothing but trouble. Drive chains come off, then it plugs up or you have to change bushings on the rods." Sam says a 1975 Ford 1-ton pickup with a crew cab was one of his “‘best buys” ever, “When we traded it in, we had 240,000 miles on it. We replaced the rings and main bearings at 120,000 miles but after that it seemed to get better with age. It has lots of power in its 460 cu. in. engine. It also got 14 to 15 mpg at 70 to 75 mph and we always had a camper on it. “We're also pleased with Del Air heat exchangers that mix cold air from outside with warm air exhausted from the building. When — it’s 40° below outside, the incoming air is at 48 to 50° above zero. We have 8 of these units in our hog operation and we are so well satisfied with them that we took our boilers out and sold them."
Ford
Wally Redfield, Morris, Minn.: ‘‘It now has 1,700 hours on it and has performed fantastically,” says Wally, pleased with his 1977 Ford 642 combine. ‘The first two years of operation, our only downtime was one broken fan belt. Since then, we have had only a few small problems. It’s easy on fuel, easy to adjust, has good capacity and is a real joy to operate.
C.S. Parks, Bangor, Penn.: ‘Since started using this disk I haven't had to pick rocks," says Parks, pleased with his Taylorway 12¥2-ft. offset extra heavy disk. ‘I farm in an area where rocks seem to grow and plowing always turns them up. This disk is heavy enough to stand up to the abuse of real rocky ground, and does a good job.”
John Deere + 1 more
John M. Gabriel, Belle Plaine, Sask: ‘A tractor is only as gocd as the service you get with it and the dealer we bought this tractor from was only interested in selling,” says John, about his ‘“‘worst buy" Steiger ST 450 tractor, “In the 14% years that we had this tractor we never had everything working at one time. We did all the warranty work ourselves and had to wait up to 6 weeks for parts.”’ He nominates his John Deere 8850 tractor as “‘best buy”. “The tractor is easy to service, a pleasure to operate and fuel economy is good. We are a little disappointed in the ground speed selection between 5 and 6% mph, but this Deere is a definite step up from our Steiger. Dealer service has been good.” Alan F, Turner, Cupar, Sask.: ‘Our worst buy was a Massey Ferguson 751 pto combine bought new in 1980. “This combine had bearings all over it that were dry and hard to get at. The flanges are all on the inside of the machine, making them difficult to change. The transport on the hitch could have been designed better by a 2-year-old and some farmer could get injured or killed with it. The only good thing about the combine was dealer service.”
New Holland + 1 more
Fred Adrian, Binford, N. Dak.: ‘We have only broken a half dozen Worst’’ Buys previous page) sickle sections on 1,500 acres of quite rocky ground,” says Fred, pleased with his 1981 114 New Holland swinger Haybine, “It has a very good floating head.” Louis F, Major, Newberry, Mich.: “This baler is a whopper!"’ says Louis, pleased with his New Holland 847 round baler. ‘We bought this baler brand new and baled 500 acres without a second of trouble or a single misbale.” On the negative side, he had trouble with his “medium size Gehl baler. We had nothing but trouble with it. The baler would not start bales and we spent more time pulling hay out of the front of the machine than we did baling.”
John Deere
Danny L. Young, Wolcottville, Ind: He's happy with his Deere 8640 and 4640 tractors. ‘Both tractors have done everything I expected and more. I've had no problems with either. Deere has an excellent warranty program, especially to update their 4wheel drives. They have taken care of previous 4-wheel drives I've owned, too.”
John Deere + 1 more
Edmund F. Marek, Penelope, Tex.: “This is one of the best tractors have owned in my 33 years of farming,” says Edmund about his Deere 4640. “This is one of the best tractors I have owned in my 33 years of farming.” ‘Handles real good, does not use any oil, has more power than the factory says and starts perfect in real cold weather. Plenty of weight for the power, too. “Our worst buy was our 1076 Ben Pearson cotton stripper from the Ben Pearson Co., Pine Bluff, Ark. There are no dealers to get parts from, and no one knows how to fix the stripper. Ben Pearson did not stand behind the warranty. I called them over and over again but they never sent anyone who could fix the power steering.” Howard E, Stidam, Medora, Ind.: He had a bad experience with a new International 425 baler. ‘When my old baler wore out, no one seemed to have a good used one so our local IH dealer said he'd make me a deal couldn't refuse on a new one. He said there was a cash rebate on the model plus a special marked down price. never did get the cash rebate. When asked why, the dealer denied he had offered one saying it wasn't in writing. This wasn't the worst of it, however, as the baler wouldn't work. It kept shearing pins on the flywheel because the needles would drop before they were supposed: to. This happened so many times that the stop dogs finally wore through the ram and took the needles out. They keep' trying to fix it but can’t. I hired more hay baled last year than I baled myself and I still have a new baler that won't work. In addition, have to pay for it as though it were perfect.”
Ford + 1 more
Norman Mairs, Nestleton, Ont.: “Driving our 1977 Ford 150 ¥ ton pickup was like trying to steer a jack rabbit. On some roads you needed two hands on the steering wheel. We had it checked several times but it made no difference. It was also heavy on gas, getting only about 12 to 14 miles per Canadian gallon." Norman's happy, though, with his 1980 GMC ¥2 ton Grande Sierra diesel pickup. “A dream to drive and steer and I'm very pleased with it although it does not give the mileage of 23 to 24 miles per Canadian gallon that it was supposed to get.”
Delbert Butts, Browntown, Wis.: “You can go right into freshly picked corn without chopping stalks and never have a plug up. Does a really good job of tilling,’’ says Delbert about his “best buy’ Glencoe Soil Saver.
John Deere
Scott Peacock, Alliance, Alb.: “Our Case 4-wheel drive tractor was a real headache. Most of the problems were related to steering yokes located at the end of each axle. Each wheel is able to turn, giving it a crab-like steering which may be good for pto implements but isn’t necessary for most types of field work. When a universal joint went out, the drive shaft cleaned house. Even the hitch busted off. Every time we had a problem, the dealer had an answer. But the only satisfaction we got was when we traded it off on a Versatile 895." Scott lists two “best buys”. “Our 8820 Deere combine and a 70-ft. by 10-in, Farm King auger are both good products. The 8820 gobbles up a 44-ft. double swath of chest-high wheat straw. A tremendous performer with capacity to match. Very few problems and the reversible feederhouse is a real back saver, not to mention safety. The Farm King auger has high capacity and couples directly behind a pto tractor so you don't have to unhook it. A hydraulic driven 10-ft. cross-auger feeds the main auger so even semi-trucks can be easily unloaded. A hydraulic scissor action undercarriage lifts the auger, empty or full, with ease.”
John Deere
Kurt Ewald, Unionville, Mich.: “Our best buys have all been Deere tractors with power shift transmissions. We've logged close to 20,000 hours without one transmission or clutch failure, including a 1968 4020 with close to 7,000 hrs. Our latest best buy was Deere’s new 4850 with MFWD. The 15-speed power shift is smooth as silk. Efficiency with the front-wheel drive is excellent.” Donald M. Hoggarth, Sexsmith, Alb. “The worst new product I have bought is a new Gilmore Tatge 580 Tox-O-Wik grain dryer. have had trouble starting the burner and keeping it lit ever since it came on the farm. The serviceman has been out five or six times but it still has the same problems. There is an air switch which lights the burner and an air line that brings air from the fan to activate the switch. The least bit of dirt from the fan will plug this air line and the burner will go out. I have had to remove this line from the dryer and clean it three times with one batch of grain to keep the burner going, which is an awful nuisance. There is also quite a bit of vibration in the drive.”
William DeYoung, Hazel Green, Wis: His “best buys” are his Duralon all-season radial tires and his Rockwell 1-in. belt sander and grinder. “The tires are the best I have ever used in the winter. And, since I purchased the 1-in. belt sander, I haven't used my wheel grinder. It does a great job on knives, drill bits and lawn mower blades.”
Garry Barton, Dix., Ill: Heading his ‘‘worst buy” list is his 1982 Reliant K car by Plymouth. “The car leaked on the front and back floor and also in the trunk. The first 6 months we owned it, it spent 28 days in the shop. The carpet had to be replaced. The dealer gave us little satisfaction and the trunk still leaks. We also wrote the company but with no results,”
International Harvester
Sidney Ebersole, Pioneer, Ohio: “International Harvester’s 645 Vibra Chisel isn’t strong enough to chisel bean stubble and it is impossible to “It is impossible to control depth— it is just plain junk!” control depth because the frame will flex. It is just plain junk!” On the positive side, Sidney's pleased with his Glencoe Soil Saver. ‘We have had no trouble, depth control is good and al! adjustments are easy to make. Our White 378 Danish tine cultivator is also a good solid machine."
John Deere
Lon E. Moen, Ortonville, Minn.: “I'm well-pleased with my 8-row Max Emerge 7000 John Deere planter. It has good seed placement and causes no problems at all. My Feterl augers are also a big plus in my farming operation,”
Ronald Hohl, Donnellison, Iowa: “One of my best purchases in the past year is an 8-in. 55-ft. bottom drive Mayrath grain auger. The auger really handles a lot of grain. It's equipped with a winch that raises and lowers it quickly, easily and safely. Despite its size, it's highly maneuverable and easy to move. It lowers fairly flat for storage. Service is excellent.”
John Deere
Deane W. Meinhardt, Kahoka, Mo: ‘‘I learned about both of my best Deane. “In 1978 I adapted a John Deere 653 row head to my M Gleaner combine, using the Bish head changer. They both have worked satisfactory and beyond my expectations. In 1980, purchased a set of Clarence Trimpe’s reworked cylinder bars (Junction U.S. 31 and 50, Seymour, Ind. 47274) and they have done everything that he said they would do and more.” Another good buy is Deane'’s Dickey John spray monitor and radar gun. ‘Very little maintenance, accurate in speed range and the amount of spray applied.”
International Harvester
Orville Rohner, Baker, Ore.: ‘‘It's heavier than most choppers but it takes less horsepower to run it,” says Orville, happy with his 7160 Hesston field chopper. ‘The blower is a direct throw. It has only four roller chains on it and it’s easy to work on, really like the hydraulic knife sharpener, although the machine only has 6 knives. Does a good job of cutting the hay.” Don Koopsma, Hudson, S, Dak.: “You couldn't grind your fingernails with it. The machine has absolutely no power.! wouldn'trecommend it to anyone,” sayd Don about his “worst buy” 6-in. ¥2 hp. KT bench grinder. He's pleased, though, with his 18%2-ft. International vibrashank cultivator coupled with a 3-bar Kovar harrow. “I like this machine because it leaves a nice level seedbed and works especially well on bean ground. Once over and you're ready to plant.”
International Harvester
Nate Reilly, Spokane, Wash.: He nominates his Ideal automatic cattle waterer as ‘worst buy”. ‘When installed the waterer the electric heating unit didn't work. The dealer wouldn't replace the unit so we bought another plastic heating unit from the dealer. It didn’t do a satisfactory job of keeping ice out of the trough sol went back to the dealer but he wouldn’t help me with the problem.” . On the plus side, he lists his International 784 tractor. “It’s a satisfactory tractor but service from the dealer is outstanding. The factory didn’t doa real good job of assembly but the dealer has taken care of everything without any questions.”
Roger Datisman, Sherrill, Iowa: “It has been invaluable in cutting, grinding and getting materials ready for welding,”’ says Roger, pleased with his Skill 3-hp, portable grinder with 9-in. blade.
Ray E. Braun, Rushmore, Minn.: “This company deserves a big thank you for the beautiful building they put up for us," says Ray, pleased with his Morton Farm building. “We have gotten many comments on the building. We weren't sure at the time of purchase as to what we wanted until the Morton sales manager took the time to explain everything in great detail and with no pressure. Also, their crew was so efficient, pleasant and resourceful that we have nothing but praise to express.”
James A. Imler, Barnett, Mo.: “'l cut 4-ft. tall weeds with it at 4 mph with ease,” says James, happy with his “best buy” Woods 10-ft. Bushhog mower, “I had a little clover that had gone to seed and the machine did a real good job spreading the seed evenly. The cutter stays at an even height so you don’t have to adjust to changing ground and crop conditions.”
John Deere
Samuel L. Keister, Bedford, Penn.: “Once they are half worn out the tread falls off, says Samuel, upset with BF Goodrich 7.50 x 16 10-ply tires. William O. Harris, Jr., Mineral, Va.: “Has a large capacity and han dles as easily as a toy. Requires little daily service, has convenient controls, good vision and a comfortable cab. Heads attach and detach very easily,"’ says William about his John Deere 6620 combine.
Bill Evans, Van Wert, Ohio: "When we received the cultivator there were parts missing and it took 2 or 3 weeks to get them. Service from the company is very slow,” says Bill about his Danish tine field cultivator from Koehn Manufacturing.
Ram
Albert L. Fries, Livingston, Mont.: “In 1973 [ bought a new 1-ton Dodge truck with the long frame. We put a 12-ft. box on it plus a hoist and you wouldn't believe the load we haul. Last fall, our last load of wheat wouldn't fit in the bin so we took it to the elevator. I had 12,750 Ibs. in it. Of course, that’s hard on tires and we don’t do that very often. Haven't had any trouble with it at all, though, In fact, it hasn't had a tuneup. We just put in new plugs and go.”
Massey Ferguson
Earl J. Peacock, Greenfield, Ind.: “I'm glad Massey Ferguson no longer makes planters!"' says Earl, about his “worst buy’? Massey 468 planter. “It wouldn't cover the seed and wouldn't plant over 1 in. deep. The way the drive chains were located, dirt would knock the chains off and it would slip. If you needed a part for it, you had to order it.”
Ford
Charlie E. Bennett, Gillsville, Ga.: “The battery was unbelievable. It lasted 9 years and 5 months,” says Charlie, about his 1973 Ford 3000. “I'm well-pleased with the tractor, too, but the battery was something else.”
International Harvester + 1 more
Ivan Gleeson, Lexington, Ill.: "I didn't think anything could be so badly manufactured as this,"’ says Ivan, disappointed with his “worst buy'’ New Idea corn picker, “I had two before and they were okay.” On his “best buy” list, he’s pleased with his International 830 chopper and forage harvester. “It outperforms the two we had before and does a super job. Our crops are heavy but the capacity of this machine is great. Also, we're happy with our International 3788 four wheel drive and Deere 4630.
John Deere
James Ferguson, Canby, Minn.: On the “best buy" side, he lists two John Deere products. ‘My John Deere 2800, on-land 6-bottom variable width spring reset plow works great and has lots of clearance. My 20-ft. Deere 9300 press drill is also a good product but I had a minor problem with the inside scrapers. Deere has changed the design and is replacing all the scrapers free of charge. It has a large grain hopper and is a pleasure to use.”
International Harvester + 1 more
Perry Black, Somers, lowa: ‘Our new International 5288 2-wheel drive tractor is so easy to operate that Itaught my new wife how to drive it. 1 wouldn't have even attempted to have her learn on our old 1466 as the clutch was impossible and the gears were extremely difficult to shift. A second best buy is our Deere 6000 Hi-Cycle sprayer. It's the most trouble-free machine I've ever owned for doing custom work and the Sound Gard cab makes it a joy to go to work in the morning.”