Real farmers rate what they bought, from FARM SHOW MagazineSubscribe  ·  Free issue  ·  Send us your Best or Worst Buy
Subscribe to FARM SHOW
Home › Issues › Vol. 6, No. 2 (1982)

Best & Worst Buys: FARM SHOW Vol. 6, No. 2 (1982)

61 reports from pages 10–13 · 53 Best Buys18 Worst Buys · See everything in this issue at FARM SHOW →

Best Buy

John Deere

Dave Aikman, Spencer, Ohio · Vol. 6, No. 2 (1982), p. 10

Dave Aikman, Spencer, Ohio: ‘The dealer misrepresented this plow. It has no trash clearance and continuously plugged in cornstalks, with coulters coming loose and breaking. Trash coverage was also very poor,” says Dave about his John Deere 3600 7-bottom plow. He likes his 52-ft. Hutchinson 8-in. grain auger. “It’s balanced perfectly and our dealer has all parts available when we need them.”

See this page at FARM SHOW →
Best Buy

George Panasuk, Bainville, Mont · Vol. 6, No. 2 (1982), p. 10

George Panasuk, Bainville, Mont: “This is supposedly Hesston's quick-tach head but, when we took the hay head off, we couldn't figure it out,”’ says George, upset with the 21-ft. grain head for his 1981 Hesston 6550 swather. ‘It took a Hesston serviceman all day to get it on. The grain head is absolutely no good. The worst machine ever owned.” On the other hand, George likes his 875 Versatile 4-wheel drive. ‘With its hinged hood, hinged radiator screen, battery swing-out and oil and filter checks at ground level, it's easy to service. Good fuel economy.” linate

See this page at FARM SHOW →
Best BuyWorst Buy

John Deere + 1 more

Dan Merkwan, Geddes, S. Dak · Vol. 6, No. 2 (1982), p. 10

Dan Merkwan, Geddes, S. Dak: “My ‘best buy’ would have to be my WL42 Westendorf loader,” says Dan. “I've got it mounted on a 4030 John Deere tractor with approximately 90 hp and it performs beautifully. In the three years I've had the loader, we've never had to repair it. It loads feed for cattle, hauls manure, and even digs rocks. The thing that sold me on the loader was the quick-tach two minute on/off feature and the good luck my neighbors had with theirs." One the ‘tworst buy" side, Dan nominates his Massey Ferguson 1100 tractor. “The tractor was supposed to have 90 to 100 hp but it can't pull alongside a 75 hp tractor. In the last few years, we've put money in the rear-end, the hydraulic system, tires, the 3 pt. hitch, and the motor twice. The air conditioner never worked properly and it only has a little over 3,000 hours on it.”

See this page at FARM SHOW →
Best Buy

Alfred Koekenhoff, Graettinger, lowa · Vol. 6, No. 2 (1982), p. 10

Alfred Koekenhoff, Graettinger, lowa: “Performs just like the company says,” reports Alfred about his Owatonna 595 round baler. “Those steel rollers make the outside of the bale really solid, leaves the bale with a soft core so the bale can breathe. had 14-ft. windrows of hay that were rained on for several days. One afternoon, I started tipping them and my son started baling one hour behind me. The hay was quite tough, but it cured well in the bale. The bales went through several more inches of rain in the fall and the hay is still very nice.”

See this page at FARM SHOW →
Best Buy

John Deere

Bill Wendlandt, Garden City, Minn · Vol. 6, No. 2 (1982), p. 10

Bill Wendlandt, Garden City, Minn: “My ‘best buy’ is the promotion and marketing I get with a one cent check-off per bushel of soybeans. The dollars sent to the Minnesota Soybean Research & Promotion Council have been a good investment. If we grow it, we should promote it,”’ says Bill. Dewaine, Rayston, Elbert, Colo.: He’s pleased with his 1981 4440 John Deere tractor. “Like the way it handles in the field and the good vision from inside the cab. The hydraulic seat is extremely comfortable.”

See this page at FARM SHOW →
Best Buy

Keith Davidson, Chickasha, Okla · Vol. 6, No. 2 (1982), p. 10

Keith Davidson, Chickasha, Okla: He's disatisfied with his Subaru “Brat” pickup. “Runs good but gets just 21 to 25 mpg, compared to the 27 to 31 mpg my old one got.” On the plus side, ‘‘My Ford 7700 tractor is easy on fuel, burning just 2.5 gal. per hour for light hay work up to 4 gal. per hour on heavy disking. Have had little trouble and the dealer gives good service.”

See this page at FARM SHOW →
Best BuyWorst Buy

Honda + 1 more

Jody Travis, Shepherd, Mich · Vol. 6, No. 2 (1982), p. 10

Jody Travis, Shepherd, Mich: “My ‘best buy’ is my Honda 185 threewheeler. It’s great for checking cattle fences and chasing after tools. Starts quick with just one pull in the winter and gets good gas mileage. The only trouble I had was with the clutch and the dealer fixed that with no charge. “Our ‘worst buy’ is our Chevrolet 1978 Blazer. When we bought it there were wheel bearings missing out of the front wheel. It gets about 7 mpg, starts hard in winter and rusted out after the second year. And now it uses oil!”

See this page at FARM SHOW →
Best Buy

Vernon Hokanson, Dundurn, Sask · Vol. 6, No. 2 (1982), p. 10

Vernon Hokanson, Dundurn, Sask: "I traded in my duals for a pair of Goodyear radials, expecting to have a more comfortable ride. Unfortunately, they made the tractor almost impossible to ride on and were certainly no improvement," says Vernon.

See this page at FARM SHOW →
Best Buy

John Deere

Ronald Day, Hammond, Ill · Vol. 6, No. 2 (1982), p. 10

Ronald Day, Hammond, Ill: Ronald had trouble with Lexone herbicide from Dupont. “It didn't control what it is supposed to. The company came out and looked at all the fields but we haven't heard anything yet from them. Our dealer is still trying to get answers for us and other farmers in this area.” Ronald rates his John Deere 4640 as a “best buy”. ‘The seat in the 4640 is the best I've ever ridden in. The tractor has plenty of power and the quad range transmission has just the right speed for our tillage equipment. After 550 hours, we haven't had a breakdown. “Another ‘best buy’ is a 13-ft. mulchtiller from John Deere. It does a wonderful job in cornstalks. Our John Deere dealer has been great on service.”

See this page at FARM SHOW →
Worst Buy

Allis-Chalmers

S. Ridgely Morison, Delmar, Delaware · Vol. 6, No. 2 (1982), p. 10

S. Ridgely Morison, Delmar, Delaware: “When was looking for a grader blade for my 40 horsepower Allis Chalmers, it seemed that the grader blades for that size tractor were all flimsy and cheaply made. The more ruggedly built blades were too heavy, requiring a 75 to 80 horsepower tractor. My dealer told me about the York 407 blade and I have not been sorry. It has the same design as the larger blades but is light enough for the smaller tractor to handle, Takes every job I give it,” On the “worst buy" side, he has a complaint about oil spouts. ‘I would good, durable spout. I don’t understand why it’s impossible to buy a spout opener for a quart can of oil that will not leak or allow the can to fall off. I've purchased spouts that leaked as much oil onto the engine as was poured inside. One spout let the can fall off, making a lovely mess.”’

See this page at FARM SHOW →
Best BuyWorst Buy

John Deere + 1 more

A.P. Vaught, Centertown, Ky · Vol. 6, No. 2 (1982), p. 11

A.P. Vaught, Centertown, Ky: “Our ‘best buy’ has been our 7720 John Deere combine. After one season of 600 acres of soybeans and 400 acres of corn, we haven't broken down for even one minute. This combine seems to have plenty of power and capacity. Its cab is comfortable and quiet. Also, dealer service is excellent. “Our ‘worst buy’ was our 510 Massey Ferguson combine. It’s never cleaned grain to our satisfaction, The screening system is obsolete. We can't seem to produce enough air to “It’s never cleaned grain to our satisfaction.” blow the fines out of soybeans or the husks out of corn. It lacks power in mud. One year, because of muddy conditions, we had to have a neighbor harvest our corn crop."

See this page at FARM SHOW →
Best Buy

Massey Ferguson + 1 more

L.R. Ward, Lecompte, La · Vol. 6, No. 2 (1982), p. 11

L.R. Ward, Lecompte, La: ‘Heading his ‘‘best buy” list is his Massey Ferguson 275 tractor. ‘'It's an economical, sturdy and well-built tractor. Dealer service has been excellent. We've also been pleased with our Stihl chain saw. The only problem was a failure of the chain oiler which was replaced at no cost to me. One other outstanding buy is our Campbell Hausfield airless sprayer. It sprays right from the paint can at the rate of about one gallon in 5 to 15 minutes.”

See this page at FARM SHOW →
Best Buy

International Harvester

Allen Littell, Rolla, Kan · Vol. 6, No. 2 (1982), p. 11

Allen Littell, Rolla, Kan: He likes his International 490 disk. “The 7% in. disc spacing takes care of weeds at a shallower depth and pulls easier. Also like the flexibility of the disk on uneven fields.” Samuel E, Hershberger, Millersburg, Ohio: Samuel likes his “Miller Blue Star 200 amp welder. It has good power and amazing output for its size, producing 120-V AC current at idle speed. Some of the best money I have spent in a long time."

See this page at FARM SHOW →
Best Buy

Larry E. Hummel, Monticello, Wis · Vol. 6, No. 2 (1982), p. 11

Larry E. Hummel, Monticello, Wis: Larry has two “best buys". ‘We bought a Madison Silo Grain-OMatic sealed storage unit six years ago and have always had top quality feed with no spoilage. Have had no service problems and Madison Silo has been -out periodically to check performance. This company is a pleasure to deal with. “Surge Orbit Mini-Breaker cups are my second ‘best buy’. They are definitely the best milker on the market. I previously had four large breaker cups with belts. I eliminated one person with the new units and still milk 50 cows in less time. Cows are much more contented with these machines, too.”

See this page at FARM SHOW →
Best Buy

Massey Ferguson

Ronald N. Hill, Sedley, Sask · Vol. 6, No. 2 (1982), p. 11

Ronald N. Hill, Sedley, Sask: ‘I've had good success and no downtime with my Versatile 835 tractor and my Gleaner L-2 combine,” says Ron about his “best buys”. On the negative side, “I bought two 18-ft. Massey Ferguson discers and had trouble with the hitch breaking on the back discer when turning corners. It would not penetrate properly. The bottom plates on the fertilizer boxes fall off constantly, Service from the dealer was fair but the company was not helpful. “Talso bought a self-propelled Versatile 4400 swather and have had lots of steering problems and variablespeed problems that affect the canvas and ground speed. Dealer service was good but the company response was poor.”

See this page at FARM SHOW →
Worst Buy

John Deere

Stan Hensley, Baldwin, Wis · Vol. 6, No. 2 (1982), p. 11

Stan Hensley, Baldwin, Wis: He's happy with his reconditioned 6-ton fertilizer spreader from Simonsen Mfg., in Quimby, Iowa. “I was getting tired of waiting to use fertilizer’ spreaders in the spring rush. Half the time, when I finally got a loaner spreader to use, it did a poor job of spreading or was broken. I thought of buying my own spreader but the prices for new ones were high for my limited use, and all the used spreaders which companies wanted to get rid of looked terrible. Finally, an uncle of mine in the fertilizer business told me about Simonsen’s. They take used fertilizer spreaders in trade on new ones, and then completely recondition the used ones. They doa good job and the spreader has been trouble free. And yes, the price was right, too.” Stan says his ‘worst buy’’ is the Cozy Cab he bought for his Deere 4020. “Why don’t companies stand behind their product? When I bought factory representative about air conditioning. He assured me there would be no problem. My local Deere dealer put the cab on with air conditioning and did a fine job. I really like the cab, but when I went to use it, the air conditioner broke with just two days use. My local dealer did all he could to help fix it. Cozy Cab said they would send a representative to fix it but he never did show up.”

See this page at FARM SHOW →
Worst Buy

Dan Stravers, Prairie City, lowa · Vol. 6, No. 2 (1982), p. 11

Dan Stravers, Prairie City, lowa: “You name it and we had it,’ says Dan about his ‘worst buy’ 1979 Chev rolet 3 ton 400 cu. in. 4-wheel drive pickup. ‘We had problems with the radiator, the water pump, starter, exhaust, and the timing chains and gears. It used one quart of oil every 300 miles when new." On the plus side, Dan's happy with his 1980 Subaru Brat pickup, “I bought it new and have over 25,000 miles with absolutely no trouble. I get 25 miles per gallon around the farm and 35 on the highway. Excellent mileage for a 4-wheel drive pickup. I sold my soybeans to Japan so! don't feel bad about buying their pickups.”

See this page at FARM SHOW →
Best Buy

Wayne Zimmer, Elkhart, lowa · Vol. 6, No. 2 (1982), p. 11

Wayne Zimmer, Elkhart, lowa: “After 45,000 bushels of drying, we still haven't got all the problems worked out,” says Wayne about his 475 M-C grain dryer, ‘““The company stood behind their product. They replaced a fan and some bearings without cost to me, The problem may be poor workmanship while it was being put together.” Wayne adds that ‘We like our International No. 14 V-chisel. The unit came equipped with automatic reset shanks that eliminate the shear pin aggravation of other makes. After more than 600 acres of trouble-free operation, this well-built chisel appears ready to serve our needs for many years.”

See this page at FARM SHOW →
Best Buy

Ron Niebruegge, Valmeyer, IIL · Vol. 6, No. 2 (1982), p. 11

Ron Niebruegge, Valmeyer, IIL: Ron's Noble 39-ft. Culti-Matic field conditioner heads his ‘best buy” list. “The tool does an excellent job of opening up and leveling off our fallplowed gumbo soil in the spring without digging too deep and pulling out mud lumps from deeper below the surface. Easily handled with a 180 hp 2-wheel drive tractor and does a surprisingly good job on weeds up to 3 to 6 in. tall, considering that it is a light tillage tool."

See this page at FARM SHOW →
Best BuyWorst Buy

Glenn Thurow, Saxon, Wis · Vol. 6, No. 2 (1982), p. 11

Glenn Thurow, Saxon, Wis: ‘We bought the windmill in July of 1980 and it was delivered by August 1980 but it wasn’t put up until May of 1981," says Glenn about his “worst buy” windmill, a Mehrkam 40 kw model. “They didn't come with the control panel until June 1981, It ‘All I’ve had is $30,000 worth of grief.” worked until September 1981. They didn't come to repair it until November, when it worked a few days and had more trouble. They haven't been back yet. All I have had is $30,000 worth of grief.” His “best buy” is his Pasquali 4wheel drive 988 tractor. “This 4-ft. wide, 38 hp tractor goes anywhere — woods, ditches, rough fields, and so on. It's only 4 feet wide.”

See this page at FARM SHOW →
Best BuyWorst Buy

John Deere

Lawrence Burkholder, Markham, Ontario · Vol. 6, No. 2 (1982), p. 11

Lawrence Burkholder, Markham, Ontario: ‘‘My ‘worst buy’ Interna tional 1440 Axial Flow combine was not disastrous. I liked it enough to trade for a 1460. However, the 1440 was underpowered for the 6-row header use. It lacked engineering ‘finish’ and durability in areas like jackshafts, the feeterhouse shaft and the cleaning fan. The International axial design needs a better stone trap design, too. They tell me one is coming for future models. On the positive side, the dealer always gave excellent service during our downtime.” “My ‘best buy’ is my John Deere Max-Emerge 6-row corn planter. “Along with liquid pop-up fertilizer, applied at low rates, this planter makes 70 acre days realistic, even in our small and awkward shaped fields next to suburbia. We routinely plant at 74% miles per hour.”

See this page at FARM SHOW →
Best BuyWorst Buy

Massey Ferguson + 1 more

Aldrich Kovar, Chatham, Ontario · Vol. 6, No. 2 (1982), p. 11

Aldrich Kovar, Chatham, Ontario: “I bought this tractor four years ago and got rid of it this year with only 400 hours on it,’ reports Aldrich about his Massey Ferguson 225 high arch tractor. “The vibration on it was so bad between 1,600 and 1,800 rpm's that it drove me nuts. Couldn’t keep lights in it and it had poor hydraulics. The hydrostatic power steering was so erratic you had to concentrate on steering it full time. Truly the worst tractor ever owned." On the other hand, he likes his Kubota 6100 tractor. ‘I use this tractor with a mid-mounted mower to cut grass. It's a good, sturdy, well built and smooth riding machine. Its 3 cylinder diesel engine is very efficient. Good service from my Kubota dealer,” Gerald L, Austin, Fairbanks, Alaska: “'! have put it through trees, brush and everything well beyond what it was really meant to cut and am really pleased with its strength and ruggedness,” says Gerald about his ‘‘best buy’’ Bush-Hog rotary cutter. ‘I have replaced one seal on the blade spindle and replaced the blades once, primarily due to my improper maintenance of the first set. The company did have some poor quality control as I have one new-type axle and one old-type axle on the same machine. can’t order a pair of wheel seals since each side is different. I also placed the bracket for the parking stand where it should have been in the first place. Even so, I would definitely buy another 405 or 406 Bush-Hog.” Gerald's had trouble, however, with another Bush-Hog product. “When I went shopping recently for a blade, I wanted a Rhino blade but there was no dealer closer than 400 miles, so I bought a Bush-Hog, My main gripe is with the options I ordered. The holes for attaching bolts for the extensions didn’t match up and the $30 skid shoes were worthless and completely unusable. They couldn't be set low enough to touch the ground. Really poor design. I had so many other things to do that I never got around to trying to return the shoes to the company. I finally made my own that are easily adjustable, removable, and they slide nice and swivel on turns,”

See this page at FARM SHOW →
Best BuyWorst Buy

John Deere

Norman Siems, Melvin, Ill · Vol. 6, No. 2 (1982), p. 12

Norman Siems, Melvin, Ill: “My ‘best buy’ was to install a twin cylinder electric hoist from Stone Hydraulic Industries, of Rockford, Ill. on my pickup. It turns a ¥%4 ton pickup into a true small truck. I have used if to haul so many different things in so many ways it would be futile to try to list them all. Iteven works as a handy portable ladder in isolated spots. The only drawback is that the amount you pull is limited unless a rigid hitch is installed. Because of the location of the fuel tanks on new models, one may have to use the type of hoist that slips into the existing bed. 1 would be concerned about the added weight for year around driving. “The Schultz planter tiller from Waterloo, lowa, is also a ‘best buy’,” Norman continues. ‘‘They suggest that you work the ground once and then plant. It works beautifully. Fits on my Deere 7000 planter. Pulls easy. No problems after two years and is still ready to go. had anticipated there would be problems in muddy pot holes that you could not ride up high enough to get out of, but was wrong.” Norman has no ‘worst buys" to nominate but says he's reconsidering the benefits of drilled soybeans. “I have had three years experience with narrow beans and my yields have, in most cases, been greater than 38 in. rows. But weeds were a problem the first year and, although that problem seems to be resolved, I have been plagued by wet fields at harvest due to the heavy canopy that doesn't let the field dry as fast as rowed beans. The anxiety and problems make it a doubtful practice.”

See this page at FARM SHOW →
Best Buy

GMC

Robert S. Postans, Heath, Alberta · Vol. 6, No. 2 (1982), p. 12

Robert S. Postans, Heath, Alberta: “My problems were minor because both companies stood behind their warranties,’ Robert told FARM SHOW, pleased with his GMC 7000 series truck with a Vermillion Manufacturing and Machine grain box. “We purhcased it almost a year ago, A hose coupler on the box broke and ‘My problems were minor because both companies stood behind their products.” Vermillion gave us a new hose, hose coupler and replaced the hydraulic oil. The truck came with a faulty power steering hose clamp and no tank gauge in one of the saddle tanks. Both were fixed at no cost, including replacement power steering oil. The dealer also extended GMC’s original 3-month warranty an extra 8 months.” Another good buy for Robert was his Versatile 45-ft., 8-in, dia, ptopowered grain auger. “It works extremely well with no vibration, -low noise and high capacity. Pulls easy on the road, lifts and lowers safely but slowly. The bad part is that it overcenters very easily and can quite easily lift man off the ground when the bottom end is lifted too high and the fellow doesn't let go. The safety cage is useless as it doesn't fit grain auger hoppers, or under trucks or anything else. To top it off, no one person can move it, except perhaps on pavement. However, we've put well over 65.000 bushels of cereal grains through it with no maintenance except greasing and tightening belts.”

See this page at FARM SHOW →
Best BuyWorst Buy

John Deere + 1 more

Lester Wissmann, Lesburg, Mo · Vol. 6, No. 2 (1982), p. 12

Lester Wissmann, Lesburg, Mo: “My John Deere 36 square baler is my ‘best buy’. I've never had a serious breakdown, and it continues to operate without any tying problems. use regular or plastic twine, both of which work fine. Good dealer service. “My ‘worst buy’ was an Allis Chalmers 942 square baler. It wouldn't take the hay. I had to bale with a single windrow so the feeder wouldn't shear pins. Field representatives checked it but didn’t think there was too much wrong. After baling 4,500 bales, I took a loss and traded it off.”

See this page at FARM SHOW →
Best BuyWorst Buy

John Deere

Raymond Gibbs, Dodge Center, Minn · Vol. 6, No. 2 (1982), p. 12

Raymond Gibbs, Dodge Center, Minn: He says his “worst buy" is “my Dry Mor Bluebird corn dryer. We used it for two years and are replacing it this year. I've never owned any machine with as many problems as it had. It would overdry and under-dry batches, and shut down many times a day. It was supposed to save 30% on fuel and increase capacity over our old AB-12 Farm Fan dryer but it didn't do either.” Raymond adds that his John Deere 4440 tractors are “best buys”. “We have two of them and they seem to be the right size for many jobs. They are very trouble free. Everybody likes to drive them.”

See this page at FARM SHOW →
Best Buy

Edwin H. Bredemeier, Steinauer, Neb · Vol. 6, No. 2 (1982), p. 12

Edwin H. Bredemeier, Steinauer, Neb: ‘‘For ‘best buy’ nominate my Foster Bunchmaster that trails behind my combine catching stalks, cobs and chaff to use as winterfeed for my cow-calf operation. The company representative stayed and showed me how to adjust it. The feed had enough protein in it that I didn’t have to buy any. got enough feed from two acres of 100 bu. milo to keep a cow 4'% months with no other feed. I only lost about 5% of my cutting ability during harvest and got about 18 tons of feed a day.”

See this page at FARM SHOW →
Best Buy

John Deere

Bill McClurdy, Truro, Nova Scotia · Vol. 6, No. 2 (1982), p. 12

Bill McClurdy, Truro, Nova Scotia: ‘This mower will cut at speeds up to 12 mph and is exceptionally good in dense crops,” says Bill, pleased with his John Deere 1320 rotary mower conditioner. “The machine is also excellent for close cutting of fine crops. It has a trouble-free conditioning system that doesn’t vibrate the whole machine as do some other models. Maintenance time is almost nil since the knives are self-sharpening. A real plus machine for John Deere.”

See this page at FARM SHOW →
Best Buy

Oregon + 1 more

Tom Schuffenecker, Oregon, Ohio · Vol. 6, No. 2 (1982), p. 12

Tom Schuffenecker, Oregon, Ohio: ‘In six months, I had all 1 wanted of Massey Ferguson tractors,’ reports Tom, upset with his Massey 180D tractor, “It started poor, had poor hydraulics, and a differential lock not worth having. gave this tractor a try but there was no way it could compare to the four John Deeres already own,” On the ‘‘best buy" side, ‘Tom's pleased with his New Idea 177 elevator. “I went through three used elevators before buying this one. It really takes the ear corn. Just open the door and let it go. “My biggest gripe with most farm equipment is that it’s poorly painted, The paint peels and there is often no primer. The paint on my Killbros gravity box and New Idea silage blower peeled the first year.” On the positive side, Loren likes his 130 hp. Deutz tractor and Calumet “T love the way it shifts.” pump and 3250 gal. tank spreader. “We bought our 130-06 Deutz tractor used with 1300 hrs. It really does a job hauling the 3250 gal. tank on the road and in the field. love the way itshifts gears. The Galumet pump really stirs the manure pond well and the spreader does an excellent job spreading it.”

See this page at FARM SHOW →
Worst Buy

Douglas Shefelbine, Holmen, Wis · Vol. 6, No. 2 (1982), p. 12

Douglas Shefelbine, Holmen, Wis: “Over the past 30 years, we've transformed our hilly dairy farm into 50 acres of apple orchards, 10 acres of strawberries and one acre of raspberries. Our ‘worst buy’ concerns the failure of the state of Wisconsin to compensate landowners for the extensive damage to farmer's crops by wildlife, especially by the overpopulation of White-Tail deer. We are currently working with state legislators and farm groups on this problem and would be interested in the experiences of others with this problem,” says Douglas.

See this page at FARM SHOW →
Best Buy

John Deere

Gene Schmidt, Smith Center, Kan · Vol. 6, No. 2 (1982), p. 12

Gene Schmidt, Smith Center, Kan: “My bad experience was with a 1980 Volkswagen Rabbit diesel. The guarantee is one year or 20,000 miles. This Rabbit was 15 months old and had just turned over 20,344 miles when a valve broke, breaking the piston head, and bending the rod. The mechanic said a flaw in the valve caused it and that the company would probably stand for the parts. That was a big joke! It cost $1,013 to get the car back and the company said it might have been a problem in service. In reality the car had actually been serviced more than required because I have always thought oil and filters were cheaper than repair work. - ['m getting rid of this car and will never own another Volkswagen.” On the plus side, Gene says his “best buy” is his new John Deere 8440. “The best John Deere have owned yet. So far no trouble and it handles great."

See this page at FARM SHOW →
Best Buy

Ford

Nancy Pease, Shelburne, Ontario · Vol. 6, No. 2 (1982), p. 12

Nancy Pease, Shelburne, Ontario: “This rototiller is belt driven and slight amounts of dust cause the belt to slip,” reports Nancy about her “Ford rototiller. We had troubles starting it and troubles getting the supplier out to service it. The combination of a slipping belt and general weakness resulted in no drive power even on slight upward inclines.”

See this page at FARM SHOW →
Best Buy

Toyota

Al Rod, Sublette, IL · Vol. 6, No. 2 (1982), p. 12

Al Rod, Sublette, IL: “I drove it hard and there isn’t one rattle. You just can’t believe it!” says Al, pleased with his 1979 Toyota Corona, “I've put on 90,000 miles, replacing the front brakes twice and two sets of tires and tuning it up when needed, The compression after all those miles was still 150 in all four cylinders. use gasohol and Baldwin filters and she runs like a sewing machine, getting 24 to 32 mpg. liked it so well bought a Toyota pickup, too,”

See this page at FARM SHOW →
Best Buy

Dana Gruetzmacher, Kewaunee, Wis · Vol. 6, No. 2 (1982), p. 12

Dana Gruetzmacher, Kewaunee, Wis: ‘My Better Bilt manure pump works very good but the company’s service is something else. They promised me October 1 delivery when ordered it August 18. It was delivered November 23rd. had ordered a 1,000 rpm pump and-stressed that part of my order in two phone calls to the company. It was delivered with a 1,000 rpm shaft, but with 540 rpm gear box. Better Bilt promised to have a 1,000 rpm pump flown in to replace it in three days. After another phone call, it was finally replaced December 20."

See this page at FARM SHOW →
Best Buy

Ralph Jones, Midland, S. Dak · Vol. 6, No. 2 (1982), p. 12

Ralph Jones, Midland, S. Dak: “This fall our custom grinder remarked on the high quality of our hay compared to other big round bales he ground in our area,’’ says Ralph, pleased with his Owatonna 595 round baler. ‘The sudan-sorghum in our area had too much moisture for conventional hard center round bales. OMC’s soft center made the difference. Easy to operate, too.”

See this page at FARM SHOW →
Best Buy

International Harvester

Paul McKie, North Augusta, S.C · Vol. 6, No. 2 (1982), p. 12

Paul McKie, North Augusta, S.C: “This planter comes closer to meeting manufacturer's claims than any other piece of equipment I have ever owned,” reports Paul, pleased with his International “Early Riser’? 800 series planter. “Easily adjusted and maintains extremely uniform seed depth, even under varying soil conditions. Service has also been excellent. “Another ‘best buy’ has been our ‘Disk Mulcher’ from Noble Manufacturing. It does an outstanding job, even under adverse conditions.”

See this page at FARM SHOW →
Worst Buy

Ford + 1 more

Harry VanderPol, Alton, Iowa · Vol. 6, No. 2 (1982), p. 12

Harry VanderPol, Alton, Iowa: “I'm not very proud of the transmission in my Ford F150 pickup,” says Harry about his “worst buy’, “I've always liked Ford pickups but I've just recently had to pay over $400 tc rebuild the transmission. The mechanic told me himself that this particular transmission was too ligh duty to be in a pickup. I guess nex time I'll get a % ton but then I'll be sacrificing ride and comfort.” Harry's had good luck with his 580-B Case backhoe tractor. ‘Have had no engine, converter, transmission, or rear end problems whatsoever in 3,000 hours,”’ says Harry. “Undoubtedly this is the best hoe in its class. Also, the dealership is tops in providing parts, service and leased equipment rentals.”

See this page at FARM SHOW →
Best Buy

John Deere + 1 more

Gene Hofbauer, Rankin, Ill · Vol. 6, No. 2 (1982), p. 13

Gene Hofbauer, Rankin, Ill: ‘Positively the best piece of engineering I've seen,” says Gene, pleased with his John Deere 12-row front folding 7000 planter. “It places the seed where it is supposed to be, even over sandhills, and has no down time. “Also on the plus side is my International 490 28-ft. disk. Performed beautifully, even in muddy conditions,” Gene's disappointed, though, with his International 500 12-row planter with end transport. “Seed placement was poor and it had no depth control, even after purchasing gauge wheels. The person who designed the transport wheel must have been 7 feet tall with 300 lbs. of muscle.”

See this page at FARM SHOW →
Best Buy

Massey Ferguson

Mark Troyer, Fredericksburg, Ohio · Vol. 6, No. 2 (1982), p. 13

Mark Troyer, Fredericksburg, Ohio: “One of my worst purchases was my Calan feeding system for dairy cows. The circuit boards blew frequently, The system just isn't a sensible approach to the feeding of high-producing dairy cows. “One of my ‘best buys’ was a Posi Lock gear and bearing puller. It grips the part to be pulled and won't let go until you want it to. Well designed. I'm also real pleased with a Massey Ferguson 285 tractor. It’s a smaller tractor with real good power and handles well. The fuel tank is a little on the small side, however."’

See this page at FARM SHOW →
Best Buy

Raymond Makovicka, York, Neb · Vol. 6, No. 2 (1982), p. 13

Raymond Makovicka, York, Neb: He's pleased with his Midland 70-335 VHF business band radios, “They're outfitted with a slide-on mount so they can be changed from truck to tractor very easily, Additional mounting brackets cost only about $10. We can get by with fewer radios and at over $400 each; it saves a lot of money.”

See this page at FARM SHOW →
Best BuyWorst Buy

John Deere

Burt Loitz, Colona, Ill · Vol. 6, No. 2 (1982), p. 13

Burt Loitz, Colona, Ill: ‘1 have never had a major breakdown with my four John Deere tractors,” says Burt about his “best buy” Deere 4020, 2940 and two 4640's. “They handle easily, ride well and have ample power. The two 4640's are hard on fuel but make up for it with comfort, handling and a ‘Cadillac’ ride.” On the other hand, Burt lists his Ford F-250 4-wheel drive pickup as “worst buy”. ‘Although it drives and rides well, the 302 V-8 engine performs terribly. It has no power and is always at the gas barrel. I’ve had the carburetor worked on three times, but to no avail. It still gets only 6 to 8 mpg. Would appreciate any advice on how to get better gas mileage.”

See this page at FARM SHOW →
Best Buy

Ben Byler, Mill Creek, Penn · Vol. 6, No. 2 (1982), p. 13

Ben Byler, Mill Creek, Penn: “We're very pleased with our two Harvestores. They can't be beat when you use them as they are intended to be used and make haymaking a breeze. Nothing magic about them. Just good common sense. Service is excellent.”

See this page at FARM SHOW →
Best Buy

John Deere + 1 more

Marvin Parmer, Wyoming, Iowa · Vol. 6, No. 2 (1982), p. 13

Marvin Parmer, Wyoming, Iowa: “The paint was so thick on this tool that it wouldn't work. It seemed like the whole unit must have been painted by dipping rather than spraying. Now that got the excess paint off, the unit works satisfactorily,” says Marvin about his Golden Rod fence stretcher.” He's also pleased with his Chevrolet LUV diesel 2-wheel drive pickup. ‘It has exceeded my expectations in every way. In over 9,000 miles of driving, it’s averaged more “It has exceeded my expectations in every way.” than 35 mpg. Fun to drive and starts without being plugged in when temperatures are below zero.” Also on the ‘best buy” side is his Montgomery Ward 3-pt. hitch adapter kit for a John Deere 60 tractor made by Worksaver, Inc. “The kit is well-built and has given me 3-pt, hitch convenience on my Deere 60 at a cost of $75 less than I could find anywhere else." Robert Strnad, Jr., Moosomin, Sask.: ‘I'm on my second 350 diesel motor for my 1979 GMC pickup. The first went out at 36,300 miles, or 300 miles over the extended warranty. After two weeks of fighting, GM paid for the parts but I was still out $700 for labor, $200 for the tow, $100 airfare to get home, plus the cost of another vehicle to get to my appointment. should mention that the number one main bearing was laying in the oil pan along with the part of the block it bolts to. The crankshaft also broke. “My Dad has a 1981 GMC diesel and three weeks ago the number three main bearing was laying in the pan of his pickup. How many motors like this are out there? I'd like to hear from others with similar problems.”

See this page at FARM SHOW →
Best Buy

Dr. John Waters, Boydton, Va · Vol. 6, No. 2 (1982), p. 13

Dr. John Waters, Boydton, Va: ‘ would not recommend the Sargom Fire extinguisher, which read about the small model and used it all on a one-foot square paper box fire, which I purposely set, to try it out. In spite of advertisements, it did not extinguish the fire.”’

See this page at FARM SHOW →
Best Buy

Massey Ferguson + 1 more

Jack Sills, Warren Ind · Vol. 6, No. 2 (1982), p. 13

Jack Sills, Warren Ind: Jack's “best buy” is his Auscherman combine cylinder bars. “I put them in my Gleaner M combine and they increased the efficiency of the machine considerably. A friend purchased them for a Massey and picked up a rock, breaking four bars. The com pany replaced them promptly.” Jack's had trouble, though, with his International 1066 diesel tractor. “In a matter of 18 months the tractor has had torque, transmission, and rearend problems on six different occasions. It should have been painted lemon yellow from the factory."

See this page at FARM SHOW →
Best Buy

International Harvester + 1 more

Melvin Aderman, Malinta, Ohio · Vol. 6, No. 2 (1982), p. 13

Melvin Aderman, Malinta, Ohio: Melvin’s “best buys” are his International 1086 tractor and his “used” John Deere 6600 combine. “The 1086 has been very dependable, with good lugging ability, and is economical and comfortable to drive. The 6600 is also very dependable and give us little downtime."

See this page at FARM SHOW →
Worst Buy

Massey Ferguson + 2 more

James Creighton, Cannington, Ontario · Vol. 6, No. 2 (1982), p. 13

James Creighton, Cannington, Ontario: James lists his Massey Ferguson 510 combine as ‘‘worst buy”. “We had nothing but trouble with this machine. It worked fine in small grains but seemed to fall apart when we got into corn. Cost us a fortune in parts and repairs the four years we ran it,”’ he says. On the positive side, he’s pleased with his Case 1370 tractor and his New Holland 892 forage harvester. “We've driven this tractor 1400 hours and it’s never been in the shop. A pleasure to operate and it's easy on fuel. The harvester is a dream to work with. Has loads of capacity. Like the flip-up feed rolls and the newstyle corn head is a great improvement over our old machine.”

See this page at FARM SHOW →
Best Buy

John Deere

Daniel Schroeder, Leipsic, Ohio · Vol. 6, No. 2 (1982), p. 13

Daniel Schroeder, Leipsic, Ohio: “One of our “best buys” ever has to be We have discovered several products in it that make money for us on every acre we farm. One is reworked cylinder bars from Clarence Trimpe, (Junction U.S. 31 and 50, Seymour, Ind. 47274). They help our two combines perform at least 20% better. Better in terms of quality, whether in wheat, soybeans, corn or sunflowers. On the minus side, Daniel is dissatisfied with his Demco spray marker. ‘‘We put it on our John Deere 335 sprayer. The marker has plastic nozzles that fit on the end of the booms and are supposed to spray a silver solution every so often. You can dial the length of mark and time between each mark, but when you are spraying at 10 mph, the mark isn't dark enough or spaced close enough for the driver to see,

See this page at FARM SHOW →
Best Buy

Glen Moretz, Joice, lowa · Vol. 6, No. 2 (1982), p. 13

Glen Moretz, Joice, lowa: “After shopping around and comparing several different brands of grain carts, we bought Kinze.”' says Glen, pleased with his “best buy'’ 400 bu. wagon from Kinze Manufacturing, Williamsburg, lowa. ‘The Kinze cart was built with much heavier material, designed better, and the price was much less than competitive models. We had no problems with it last fall.”

See this page at FARM SHOW →
Worst Buy

Oregon

John Horton, Dairy, Oregon · Vol. 6, No. 2 (1982), p. 13

John Horton, Dairy, Oregon: Both his best and worst buys are chemicals. ‘‘Hoelon herbicide did an excellent job of killing wild oats for us. We applied it by air at the three leaf stage and got an excellent kill in barley,” he says. ‘As for Avenge herbicide, not only did it not kill the wild oats, it set the barley back. Due to this lack of results, we had a bumper crop of wild oats for Hoelon to work on and it dida good job.”

See this page at FARM SHOW →
Best Buy

International Harvester

Thomas Gariety, Versailles, Ohio · Vol. 6, No. 2 (1982), p. 13

Thomas Gariety, Versailles, Ohio: Thomas likes his International 5100 grain drill. “This is the best tool we ever bought,” he says. ‘It has the best press wheel attachment on the market. The drill holds 33 bu., which lets you do a lot of acres without stopping. We had the worst wet weather that we've ever had last year, yet the drilled beans came up better than 30-in. row beans. That tells you what kind of drill it is.” Thomas adds that, ‘‘Thanks to we have never bought anything that gave us problems or resulted in failure. [know that’s a big statement, but it's the truth. We keep a tight maintenance schedule and try to be be very knowledgeable in buying.”

See this page at FARM SHOW →
Worst Buy

International Harvester

Albert Smith, Overbrook, Kan · Vol. 6, No. 2 (1982), p. 13

Albert Smith, Overbrook, Kan: Heading his ‘worst buy” list is his International 1086 tractor. ‘I had trouble with this tractor jumping out of low range and had nothing but trouble with the hydraulic system. It had broken lines, a blown cylinder, blown hydraulic hoses, and then a sheared bolt in the pump shut it down completely. One hundred hours later there were problems with the T.A. and 10 hours after that with the rear end. This tractor has been in the shop 75% of the last six months. “I got no help from the dealer so appealed my case to IH, A district representative came out to see me and said that if the tractor fell apart at 1,500 hours the company could take no responsibility or pay any damages. In other words, he told me that the tractor was no darn good and neither is the company if they can’t build a tractor that won't stand up any longer than 1,500 hours.”

See this page at FARM SHOW →
Best Buy

International Harvester

John Blaska, Marshall, Wis · Vol. 6, No. 2 (1982), p. 13

John Blaska, Marshall, Wis: John names as “best buy” his Herdex dairy records system from Raytec Manufacturing, Rt. 3, Ephrata, Pa. “It takes only seconds a day to keep the breeding and health records for our 75 cow dairy. The color coded records tell you at a glance the reproductive performance of a particular cow. Anyone on an AI program should not be without this system. “We're also well-pleased with our 5100 International soybean special drill. It places the seed at a uniform depth in both ideal conditions or trashy, cloddy fields. The metering system is also very accurate. We use this drill for oats, wheat and soybeans. The press wheels do an excellent job of controlling depth.”

See this page at FARM SHOW →
Best Buy

Pete Vanderploeg, Hickory Corners, Mich · Vol. 6, No. 2 (1982), p. 13

Pete Vanderploeg, Hickory Corners, Mich: ‘‘We'’re extremely pleased with the seedbed prepared by this machine in a wide variety of soil conditions,” says Pete about his “best buy" Glencoe 203 Soil Finisher.

See this page at FARM SHOW →