Case-IH 9280 tractor
“I’m well satisfied with my 1992 Case-IH 9280 tractor. This is the third one I’ve owned. These tractors run and run and run without any breakdowns. I put about 8,000 hours on a previous one without ever putting a wrench to it.”
78 reports from pages 12–15 · 70 Best Buys20 Worst Buys · See everything in this issue at FARM SHOW →
“I’m well satisfied with my 1992 Case-IH 9280 tractor. This is the third one I’ve owned. These tractors run and run and run without any breakdowns. I put about 8,000 hours on a previous one without ever putting a wrench to it.”
“I like my Massey Ferguson 8780 combine. It works as well or better than other combine makes in all crops and conditions. And, it has only about half as many moving parts.”
Jack’s impressed with his 2000 New Holland 8770 tractor. “It has a lot of power and is easy to handle. It has a super steering system that lets me make sharp turns. My only complaint is with the temperature control system on the air conditioner and heater. The blower always stays on, even though there are times when I don’t want it on.”
A 2001 Chevrolet Silverado Duramax 3/4-ton ton pickup equipped with a diesel engine rates as Duane’s “best buy.” “It’s a durable pickup and is reasonably fuel efficient. It gets 20.4 mpg on the highway and 18 1/2 mpg when towing a horse trailer. It’s comfortable and a pleasure to drive. I raved about it long enough that my friend ordered a 1-ton Chevy 3500 for his farm.”
On the negative side, he lists his 2003 North Star corn stove which he bought from Northern Tool. “This stove never worked efficiently from the start, and I’ve gone through two auger motors in just a little over a year. I paid about $1,000 for it. What it needs is a stirrer on the firepot. It’s hard to start and even harder to keep it going. Even using dried corn and pellets in combination didn’t work very well.”
Duane nominates his 1995 Dodge Dakota pickup equipped with a 318 cu. in., V-8 engine and 4-speed automatic transmission as his “best buy.” “With only a few parts and very little maintenance other than regular normal service, it has provided us with a comfortable ride, pulling a trailer with a classic car or tractor many, many miles - including one trip from Tennessee to Colorado. We haul firewood and hay, and bounce around our pasture checking cattle and fixing fences. It has about 145,000 miles on it but we think it’s barely broken in.”
“It’s one of the most comfortable vehicles we’ve ever owned,” says Wesley about his 1997 Ford Expedition equipped with a 4.6-liter, V-8 engine. “We bought it used with about 70,000 miles on it and have had no problems with it. It now has more than 140,000 miles. It gets 20 to 21 mpg. We’ve been using Ford pickups for 30 years and have had great service from all of them.”
“Our Deere LX 255 riding mower is one of the best mowers that we’ve ever owned. We mow six yards with it every week, and the only parts that we’ve had to replace are belts and pulleys.”
“I have three 2001 Case MX110 tractors and they’re all best buys. I use them for commercial ditch mowing. Last year we cut more than 14,000 acre of ditches and only had two days of down time with one tractor. I really like the 5.9-liter Cummins engine. It’s very economical.”
“My 1977 Dodge 3/4-ton, 4-WD pickup is a powerful pickup with a 525 hp, 440 cu. in. Chrysler engine. It will pull a tremendous load. I use it to pull a couple of loader tractors and a backhoe on a trailer - a load weighing 16,000 to 18,000 lbs. - with no problem. This pickup was specially built for Chrysler’s racing division and was used as a chase truck for an off-road racing team in Baja California. It came from the factory with Hedmond headers on the engine. I bought it used with 300 miles and paid $7,500, which at the time was half as much as I had just paid for my house.
“This pickup has full-time 4-WD and is equipped with 4:30 low-ratio axles instead of the normal 4:10. As a result, it gets only 8 mpg no matter how hard or how easy I drive it. It has a big 45-gal. fuel tank that barely clears the pickup’s spare tire. It also has a specially designed 4-tube radiator core that’s 2 in. taller and 4 in. wider than a regular truck core. When the radiator rusted out I had to have it recored at a cost of $400.”
Earl isn’t happy with Gensco aircraft tires. The company sells recycled aircraft tires and ready-to-bolt-on wheel assemblies for use on agricultural equipment such as tractors, mowers, cutters and shredders, grain carts and wagons, etc. The tires are said to be virtually flat-free.
He bought four tires for a total of $388. Two of the tires were 14-in., 4-bolt-hole models that went on his Bush Hog mower and worked out fine - he still uses them. However, the other two were supposed to go on front of his Allis Chalmers WD45 tractor. They never made it onto the tractor.
“The front tires on this tractor have a 5-hole bolt pattern. The problem was that I couldn’t get the company to make the wheels right. I removed one of the wheels and put a cardboard up against the back side and drew in all of the holes. I sent the drawing to the company so they could custom make the wheels. However, the wheels they sent didn’t fit. I told the company about the problem and they told me to send them back. They sent out a truck to pick the tires up. That was the last time I ever saw them. I contacted the company repeatedly but always got the runaround. Finally I got disgusted and gave up. I never got any money back.”
Gene’s 2003 Stihl MS 290 chain saw rates as his “worst buy.” “It replaced a 20-year-old Stihl 029 model that was dependable and solid and always started. However, when it finally wore out I bought the new model a year ago, and it has spent three months of that time in the dealer’s shop. It’s extremely difficult to start, and some days I can’t get it started at all. It’s an unreliable machine. I wasted $300 on it.”
Donald says his 1946 Cockshutt 30 tractor equipped with a loader is his “best buy.” “It has live power and live hydraulics. I bought it new and paid $700 on top of a trade-in. It’s a good, economical tractor. I used it to pull a 3-bottom plow. It has a creeper gear and a high-low range, which gives it six forward and two reverse gears.”
He likes his 1999 Ford F-150 extended cab pickup equipped with a 4.6-liter, V-8 gas engine and automatic overdrive transmission. “It’s roomy enough to carry four adults and gets a respectable 22 to 25 mpg.
“I bought an International Harvester 1466 tractor from a friend for $4,500 and use it every day. I haven’t had any major problems except I had to buy a new set of Taper-Loc spindles.
“I bought a Case 2470 4-WD tractor at an estate sale for $4,500 and it’s a best buy. It lets me work the ground a little sooner and also use bigger equipment. It’s now my main tractor. It works great in mud.
“My 1986 Honda 3-wheel ATV is a best buy. I put about 600 miles a year on it. Other than gas, oil and filters, and a set of 6-ply mud tires I haven’t spent a dime on it since it was new.”
On the negative side, “The 12-speed drill press I bought from Harbor Freight is a piece of junk. You have to watch what you buy from them. From now on I’ll buy only brand names.”
“I like my 1969 International Harvester 656 tractor. It’s big enough to handle round bales, yet it also works great for small loader chores.”
They like their two 2003 Kubota 4800 SU tractors. “These tractors are easy to operate and user friendly. They contain many big tractor features not found on other brands. We can’t say enough good things about them. They’re built simple and are a pleasure to use.”
“My 1974 International Harvester 1066 tractor is a best buy. Over the years I’ve spent only about $2,600 on repairs. About $1,000 of that was to tighten the front end and another $1,000 to put a 50-cent O-ring in the transmission. And, I spent $600 to fix the parking brake. This tractor always starts and doesn’t use any oil. It still has the original clutch, brakes and transmission.”
“The Snap-per weed trimmer I bought last year is my best buy. It starts easy and does a good job even in big weeds. It’s also easy on the cutting string. I really like it.”
“Thirty years ago I bought a used Farmall 560 diesel tractor. I rebuilt the engine 20 years ago and have used it ever since as my baling tractor. I haven’t had any major problems with it.
“My 1992 Ford Explorer is my worst buy. Before it had 100,000 miles on it I had to replace the rear pinion bearing, transmission, engine, and air conditioning condenser.”
Glen says he’s “generally satisfied” with his 1968 Ford 4000 flat deck row crop tractor. “It has power steering and a smooth shifting 4-speed standard transmission with high and low ranges.“
John and Peggy Milliman, I can also buzz around the neighborhood to check on things and stop to chat with many folks. It’s like riding around on your porch -people always stop us to talk.”
A 2000 Deere 6 by 4 Gator equipped with a diesel engine rates as their “best buy.” “It’s absolutely the ‘most valuable player’ on our farm,” says Peggy. “We use it for everything from daily cleaning of our commercial boarding stable to maintenance of a 90-home upscale housing development, to taking care of our draft horses and a 17-acre commercial Christmas tree farm. The one constant to our success and sanity is our Gator.
“I’ve been a paraplegic for 21 years. Until we bought the Gator, I mostly did paperwork. Now I can get out to the fields and see all the places where my husband and daughter ride.
“My Drill Doctor is my best buy (Dakota Sales, Wyndmere, N. Dak. ph 800 260-9944). It lets us pull all our old dull drill bits back into like-new condition. It comes with good instructions so anyone use it.”
“I’m generally satisfied with my 1994 Deere 8760 tractor.
“My 1974 Deere 4230 tractor has more than 11,000 hours on it but still works great. It has never needed a major repair.”
A Ursus 2812 tractor equipped with a Bush Hog front-end loader rates as Vern’s “best buy.” I just fuel it and use it. No problems of any kind.”
“My Hole Deal post hole digger is my best buy (Jeff Vaughter, Stevens Point, Wisconsin ph 715 341-4315). It’s easy to use and makes neat straight-sided holes. When you use it you don’t have to crack your knuckles together. Also, poles and posts set quicker because less dirt is disturbed.”
“My Rodenator Pro, which I bought last April, is my best buy (Meyer Industries, Midvale, Idaho ph 800 750-4553; www.rodenator.com). It’s designed to destroy gophers and other destructive burrowing animals and consists of a 4 1/2-ft. long wand that mixes oxygen with propane. It uses an electronic solid state ignition system powered by two 9-volt batteries to develop a large controlled spark at the end of the wand, which ignites the gases in the tunnel system.
“I use it to kill gophers in alfalfa fields. One thing I wasn’t as impressed with was the company’s 2-wheeled cart that’s designed to carry the wand and all the accessories. It’s solution is to replace the spark plugs every four to six hours. The tractor has unresponsive steering, and there’s not enough weight on the front end to assist in traction. The traction problem is even worse if there’s any load on back. My other Gator - a 4 by 2 - runs fine.”
“I like my Amaizablaze 4100 corn stove fireplace insert (Snively Alternative Energy, McComb, Ohio 45858 ph 888 764-8359 or 419 293-2465). It’s located in our basement and has reduced the heating bill in our log home from $300 to $600 per month down to less than $100 per month. The company offers several different models.”
“We recently bought a new Flexicoil 6000 disk seeder and 340-bu. air tank as well as 120-ft., 1,200-gal. sprayer. We had to spend three days on each machine adjusting and replacing parts in order to get the machines out into the field. The sprayer caused the most problems because the solenoid valves were hooked up wrong. Five shut-off valves were broken and had to be replaced before we could even start using it.
“We met with the company and told them about the problems, but they insisted everything had been checked out prior to the sprayer leaving the factory. It cost us more than $1,500 per year just to keep the machine running. The dealer who sold the machine to us is no longer in business. We’d have to look really hard before we’d buy another Flexicoil machine. We finally traded the sprayer in for a Melroe 4640 Spra Coupe. It’s simple to operate and doesn’t have as many electronics to malfunction.
“It’s sad that after spending so much money on equipment the company gave such poor service and had such a poor attitude toward a customer. Our farm is located only 120 miles from their factory, so they could have come out and corrected the problems. This company needs to change their attitude regarding customer service.
“Our Deere 9300 tractor is an awesome piece of machinery. It has super hydraulics and is very user friendly. Deere equipment is well-tested and proven. It keeps its value well.”
“My Deere Gator 6 by 4 equipped with a gas engine is my worst buy. The back cylinder keeps ‘loading up’, causing it to run on only one cylinder. The dealer supposedly followed the factory’s repair suggestions and charged me more than $250, but it wasn’t long before the problem reoccured. We’ve found that the only
A 1/2-in. drill from Harbor Freight rates as David’s “best buy.” “I’ve tried my best to break the darn thing but I can’t. I’ve used it to build my log house and countless other projects.
“A creeper that I bought from Harbor Freight is my worst buy. The wheels broke off after only about a week of use.”
“My 1960 Minneapolis Moline M5 tractor is my best buy. It has a lot of features that you wouldn’t expect to find on an older model, and it has a great hydraulic system. However, the power steering system could be better. I use a Farmhand F-11 front-end loader on it, which works great for stacking round bales four high. I’ve been looking at new tractors but haven’t found one as dependable as this one. Also, I haven’t found a tractor with a pressure down 3-pt. hitch like the one on this tractor. It works great with a post hole auger.”
William’s happy with his 1981 Ford 6700 tractor. “It just sips fuel compared to our other tractor. It has about 6,500 hours on it and is a pleasure to operate.
“My 1980 Ford F-150 XLT pickup has about 185,000 miles on it but still runs good and doesn’t use any oil.
“My 1984 Honda 200 4-wheel ATV is a best buy. We use it to spray, seed crops, and check and feed our cattle. This machine is easy on fuel.”
“My son has a Snap-On wire welder which is a worst buy. He can’t get parts for it and the dealer is no help. It will be the last Snap-On tool on this farm.”
“My Walker zero turn riding mower is my best buy (Walker Mfg., Fort Collins, Colo). I bought it used about two years ago, but I know it’s at least five years old. It’s a fabulous mower. My wife, who is well up into her 70’s, likes small and built too light. So I paid $1,000 to have a friend of mine build a trailer for me.
“The trailer measures 5 ft. wide by 7 ft. long and rides on 16-in. wheels. It has a steel floor with metal brackets on front and back to contain the oxygen and acetylene tanks. Rubber and nylon straps hold the tanks down. A bracket on one side of the trailer supports the wand, which rests inside styrofoam holders to keep it from getting scratched up. An automatic hose reel bolts to the floor on back, as well as a shovel-holding bracket.
“I pull the trailer behind either my ATV or pickup and have a different hitch for each vehicle.” it so well that if a blade of grass dares to grow, you’ll find her out on the machine mowing it down. We have a large yard filled with trees, but it’s no problem for this zero turn mower.”
“It’s a good and faithful tractor,” says Dorothy about her Deere 4020. “We also have a Deere 3020 as well as two International Harvesters. However, we like the 4020 best for general farming. The 3020 works best for feeding cattle but I wish it was easier for older people to get on and off.”
“I received a General Electric 22-channel basic GMRS/Vox two-way radio as a gift and I’m not impressed with it. My wife bought it for me because I’m disabled. However, they didn’t work right from day one. The send button was stuck, and the company wouldn’t honor the warranty because I didn’t have an original bill of sale.”
Roy nominates his 2001 Stihl chain saw as his “worst buy.” “I’ve never been able to cold start this saw without having to remove the filter first and squirt starter fluid into the open throat of the carburetor, then pull to start the machine with the filter off the saw. The starting instructions say to place your right foot into the rear handle and press down. However, I wear a size 10 1/2 shoe and can’t get any part of my shoe into the handle to hold it down due to the size of the handle. My 20-year-old Pioneer chain saw starts a lot easier than this one.”
“It’s easy to operate, runs quiet, and is fuel efficient,” say Anthony and Phillip about their 1986 White 2-65 tractor. “It has only a 15-gal. fuel tank, but when we use it to bale hay we can go all day long and and still have the tank one fourth full at the end of the day. It’s easy to shift gears on this tractor. However, there should be more gears between 1 and 6 mph. Another problem is that almost all the silver paint has worn off the tractor.”
A 2004 Toyota Tundra longbed pickup equipped with a 200 hp V-6 engine and manual transmission rates as Bill’s “best buy.” “It’s priced low in the $15,000 range, is easy on fuel, and has a lot of hauling capacity. It came with air conditioning, power brakes, and power steering. It’s a fun pickup to drive.”
“My Mantis rototiller is an excellent value. It’s relatively inexpensive and works every time. It’s got enough power to level the berm in the middle of our dirt road.”
Gerald says his 1964 and 1969 Deere 4020 tractors are both “best buys”, as well as his 1962 Deere 3020. They’re all equipped with power shift transmissions. “When my children were home they helped with field work, fencing, rock picking, and feeding bales to cattle. I had to change the 24-volt system and harness on the 3020 because the generator was inadequate. An alternator has more output. We also put in a 12-volt starter.”
“My worst buy of all time was a 2270 White 2-wheel drive tractor. It has a quiet, low rpm engine and a good, roomy cab. But oil leaks were everywhere on the engine, transmission and rear end. I always kept lots of O-rings on hand. All my problems were finally solved when this quiet engine blew an 8-in. hole out the side of the block. Now, thank goodness, it sits unused out in the back yard.”
“My best buy is my FARM SHOW CD-Rom, which contains 28 years of FARM SHOW articles. In some ways, it’s also my worst buy since I’m now so busy building a number of projects that I read about that I no longer have spare time for fishing.
“My worst buy is my 1997 Ford Windstar. I was interested in your articles last year about problems with the Windstar. Mine also had a bad head gasket. I caught it quick with a radiator sealer. It now has 103,000 miles on it and I don’t want to spend any money on it. Do Ford engineers ever drive and work on their own vehicles?”
“I needed two hub bolts for an old IHC 706 tractor. As far as I know, you can’t get them anywhere except through Case-IH and you have to pay $47.10. It’s very costly but I couldn’t get along without them so what can you do?”
“My 1984 Deere 2950 tractor, which was made in Germany, is my best buy. We use it during the winter to haul bales to our cattle. It never fails to start. It has about 7,500 hours but still uses very little oil. The only negative is that my son Don services the tractor and says some things are harder to get at than they are on an American-built tractor. For example, the fuel and oil filters. Also, the hood has to be removed in order to get at the air conditioning unit.”
“I’m well satisfied with my 1983 Deere 4450 tractor. It has more than 15,000 hours on it, but neither the valve cover nor the oil pan have ever been removed. However, it could have used a better job paint job. Here in south Texas we farm all year long so the sun and weather conditions are hard on a tractor’s paint.”
Stephan likes the pole saw attachment he uses on his Homelite gas-engine powered weed trimmer. “This tool lets me easily and safely trim trees and limbs up to 6 in. in diameter, up to a height of 12 ft. or so. It’s just amazing the number of tree limbs I can cut at the edges of fields. I have to use safety glasses and a hard hat because of all the falling wood.”
William’s impressed with his 1989 GM Sierra 1500 pickup equipped with a gas engine. “It has more than 264,000 miles on it but still runs strong. It has needed only minor repairs over the years, although I did have to repaint it. I love this pickup and don’t ever want to give it up.”
“It still cranks easy and runs great,” says Dick about his “best buy” 1939 Allis Chalmers B tractor.
Otis is disappointed with his 1985 Ford 6710 tractor. “I bought it new and have changed the oil regularly every 50 hours. At 2,638 hours, the crankshaft and three rods went bad, even though I had never worked the tractor hard. I sent a letter to the company but they never even acknowledged receiving it. However, I know they got it because in the letter I praised our local dealer who had put in a new engine in the tractor - at a cost to me of $7,000 - and a New Holland rep showed them my letter. Another problem is the front axle spindle is built too light. I’ve broken three spindles so far, and the last time one broke the tractor rolled over. It’s not easy to get out of a tractor cab when the tractor is lying on its side.
“I needed bearings for the tractor one Saturday but the dealer didn’t have any. He said I should go to a Napa auto parts store because they have the same bearings this tractor uses. Does it make sense for a tractor axle to use the same bearings as a car? Talk about cutting corners.”
“I like my 1974 Bobcat 371 and 1976 Bobcat 825 skid steer loaders. Both machines have been used hard in construction work but have required little maintenance.”
“My 1999 Chevrolet S-10 pickup is my worst buy. The tailgate cables on it broke and our dealer wouldn’t replace them. Neither would the company. The dealer said it was a maintenance problem. “
Rollie’s impressed with his 1981 Massey 2745 tractor. “I can’t afford a new tractor with all the modern comforts so I bought this one. It rides great and is comfortable to drive. It’s a dependable tractor. “
“It has more than 190,000 trouble-free miles on it,” says Michael, pleased with his 2001 Dodge 4-WD extended cab pickup equipped with a 5.7-liter Cummins diesel engine and 6-speed manual transmission. “I use it to pull trailers in the mountains and one time I burned out the front brake discs, which had to be turned. No other problems. I like this pickup so much that I just bought another one like it.”
“The Michelin 650/75 R32 radial tires we bought for our Versatile 895 tractor are our
“I have five Ford vehicles and all but one have more than 100,000 miles on them. The accumulated mileage on them is more than 766,000 miles. The oldest is our 1980 Ford F-150 4-WD pickup equipped with a straight 6-cylinder engine and 4-speed transmission. It has more than 130,000 miles on it. I use it for fencing and general repair work. I also have a 1996 F-250 4-WD pickup equipped with a 5.0-liter engine and 5-speed transmission. It has more than 78,000 miles on it. We use it to haul cattle and large loads.
“I have two Ford Escorts. The oldest is a 1992 model with more than 210,000 miles on it and it’s still running strong. My son drives it every day to work. My 1998 Escort has more than 148,000 miles on it. I drive it every day and average more than 38 mpg. My wife drives our 1993 4-WD Explorer every day. It’s equipped with a 4.0-liter engine and 5-speed transmission, and it just passed the 200,000 mile mark. Recently I’ve had to spend some money on repairs to the transmission. I also had to have the electronic 4 by 4 motor and the clutch and pressure plate replaced. It also needed other minor repairs.
“I do most of my own maintenance such as oil changes, tire rotation, and minor repairs. I use only Motorcraft oil and filters on all my vehicles.
“I have a Ford 1710 4-WD tractor equipped with a Westendorf T 110 front-end loader which I really like. This tractor has more than 650 hours on it. I use it every day on my farm to haul bales and wood, rake hay, plant crops, and cut brush. We use two other Ford tractors on our farm. Both are diesel powered and have more than 3,000 hours on them.”
Mike’s impressed with the customer service offered by grease to remedy the over greasing. This synthetic spray grease is very neat and easy to apply. It leaves behind a thin tenacious film that will not wash off or be pushed off the way grease can be. One can of the 5th wheel grease will last 2 to 4 applications, depending on how liberal it is applied.
In my work, I’ve found that these two products applied to a 5th wheel hitch greatly reduce problems hooking and unhooking. I also use the Amsoil MPHD as a chain lube, on door hinges, grain trailer door slides, etc. Because it locks out oxygen and won’t wash off, it also helps prevent corrosion. They work so well I have become an Amsoil dealer and can help anyone who wants to try these products.
Contact: FARM SHOW Followup, Don Smith, Smith Repair, 2865 Union Ave., Fredericksburg, Iowa 50630 (ph 877 237-6536 or 563-237-6536). Master Lock. He bought one of the company’s resettable combination padlocks. “If the lock hangs outside it can become hard to open. I sent the lock back to the company and they replaced it promptly, no questions asked. They even sent a check to cover my cost to send the lock back to them.”
He’s unhappy with his General Electric 15 cu. ft. chest freezer with lock and defrost warning. “The freezer died under warranty, and when I called the company I was informed the full parts and labor warranty applied only if you lived in a big city service area.”
“I like my 2000 Kubota M9000 84 hp 2-WD special utility tractor equipped with a synchro-mesh transmission. It cost $20,000 less than a comparable American made model. It doesn’t have a cab but it has good hydraulics and nice, large 18-in. front wheels. It starts good in cold weather. I like the tractor’s electric engage pto. I also like the synchromesh transmission because it allows me to shift gears while moving. One problem is that the brake pedals are too small and too close together for my size 14 shoes. The tractor came with a 300-lb. weight permanently mounted on front. I wish there was a front weight bracket. I also wish the tractor came with rear working lights.”
“I like my 1972 Massey Ferguson 135 tractor equipped with a 3-cyl. engine. No major problems. I put a hydrogen kit on it.”
Scott’s impressed with his Ingersoll Rand 60 upright air compressor. “I bought it used from a garage sale and it has worked flawlessly for five years. My wife criticized my decision to buy such a large unit. However, after I used the compressor to remodel several rooms with retexturing and new trim she’s okay with it now.”
On the negative side, he lists the Egg Wa-ver egg cooker designed to be used in microwave ovens. “When I first saw this product on TV, I knew I had to have it. I usually eat my breakfasts on the run and the idea of instant scrambled eggs sounded great. The This pickup has tremendous torque, handles well, and is a pleasure to drive. Without pulling a trailer it gets 20 mpg on the highway.”
David nominates his 2000 Ford F-250 4-WD pickup as his “best buy.” “It leaks absolutely no lubricants of any kind and doesn’t even collect dust on any seals or gaskets. It has a lot of power and excellent brakes, heater, air conditioning, doors, tailgate, etc. I can’t find anything that needs to be improved on it. No problems.
“My 2002 Chevrolet Duramax 3500 pickup equipped with an Allison transmission is my worst buy. The doors on it sagged and can’t be adjusted. The front pump on the transmission leaks. It doesn’t have enough power, though the fuel economy is okay. I wouldn’t want my worst enemy to buy one.”
“My 1976 Deutz D130-06 tractor, which I bought used in 1989, is my best buy. I’ve had virtually no problems with it. The engine has 7,900 hours.”
He likes his Rat Zapper trap (Professional Pest Control Products, Pensacola, Fla. 32526 ph 800 434-4555; www.pestproducts.com). It operates on four AA alkaline batteries. To set it, you place a small amount of dry pet food at the rear of the trap. When you turn on the unit, the red light will first blink and then stay on letting you know the trap is set and ready for action. Place the trap on a flat surface against a wall. Once the rodent enters the Rat Zapper, the trap senses the presence of the animal and gives it a lethal electric jolt. The trap’s red light will now blink, letting you know you have a dead rodent in the trap. You can empty the trap by turning it upside down, allowing the dead rat or mouse to slide out.
“I was skeptical of this product when I bought it, but it worked so amazingly well that I bought another one for our barn. It’s quick, effective and humane. It gives rats a ‘shocking’ dining experience,” he says.
“My 2002 Land Rover Discovery SUV is my worst buy. My wife liked these vehicles so we purchased one. In my opinion they’re extremely overrated and lack some very basic functions found in other vehicles. The engine is underpowered and just slugs along. The real problem, though, is customer service at the dealer level. They overpromise and underdeliver, and they’re rude. Next time I’ll buy a Ford.”
“My 1982 Deere 4640 tractor is my best buy. It has a great cab and more power than my Deere 4320.”
Randy nominates his 2002 Ford F-250 Super Duty 4-WD extended cab pickup equipped with a 7.3-liter Power Stroke diesel engine as his “best buy.” “I’ve used it a lot to pull a 36-ft. tandem axle, 20,000-lb. rated gooseneck trailer on which I haul a Ford 555 backhoe.
“I like my 1986 Deere 950 4-WD tractor equipped with a front-end loader. Our neighbors all had big tractors and at first they laughed at my little 31 hp tractor. However, over the last 20 years I’ve used it several times to pull their tractors out of swamps and I’ve dragged a lot of stuck trucks and trailers out to the road. I have had clutch problems with it and am now on my third clutch.”
“My Toyota Tacoma 4-WD pickup and Toyota Echo car are both best buys. They’re trouble-free and have never been back to the dealer. They’re also fuel efficient. The Tacoma has the best gearing of any pickup I’ve ever owned.”
“Clint’s the satisfied owner of a 2003 Echo extendable chain saw. “With this extendable saw I can trim trees from the ground as high as I could if I stood in a Caterpillar loader bucket - and it’s much safer this way.”
On the “worst buy” side, he lists his 2002 Sears Craftsman cordless drill. “I hadn’t used it much when the battery charger quit working. Unfortunately, the company wouldn’t honor the warranty. I bought another charger for about $65 but it, too, quit working within a month. The company refused to either replace or repair it.”
“It’s a simple, reliable tractor that’s also easy to maintain,” says Roger about his 1993 Ford Versatile 876.
“My 2000 Ford Power Stroke diesel crew cab 4-WD pickup has performed flawlessly with only normal maintenance. When you pull a tractor you can’t even feel it back there. I’ve driven it twice to the Atlantic Coast and once to the Pacific. It’s my best buy.”
“I like my 1970 Long DT 445 4-WD tractor. It’s easy to work on and has a positive traction rear end which provides great traction.”
A 1996 Mercedes 300 D car equipped with a diesel engine rates as Henry’s “worst buy.” “I had a lot of trouble starting this car. I took it to the dealer twice - once for four weeks and again for five weeks. When I went to pick up the car, they had washed it and I couldn’t start it. Finally, out of desperation, I bought another car off the lot. I noticed that there were five or six Mercedes cars there with the same problem, and they were all diesel models.”
“I operate but don’t own a 2002 Kubota M110 tractor equipped with an Alo Quicke front-end loader. This tractor handles well. However, I don’t like the powershift transmission on it because it doesn’t always engage when I push the button in. This tractor is built too light for the power it has. Also, the drive train is built too light. The loader is also built way too light which caused the arms to bend.”
“I like my 2003 GM Sierra pickup. It’s equipped with all the bells and whistles and has superb fuel efficiency.”
“My 2002 Kubota M 9000 tractor does everything I ask it to. It handles my cutter-baler nicely and uses about two gallons of fuel per hour. I paid $24,000 for it which I think was a good buy.”
“I like my 2003 Mahindra 3510 4-WD tractor equipped with a front-end loader and 6-ft. bucket. I’ve always tried to buy American-made products but the price difference on this package deal was so sweet that I couldn’t turn it down. This tractor has been stuck once, buried below the axle. That’s because it’s fitted with short, wide industrial tires that don’t work well in mud. However, the wide tires don’t makes deep ruts in my lawn while I’m mowing, which I like.”
“Although I like electronic assistance for row guidance, mapping soil profiles with yields, chemicals applications, record keeping or what have you, I haven’t found a single company that can do it all. And often the electronics from one company don’t interface with those of another’s.
“It can get expensive. I can pay out $2,000 for a receiver then learn I need to put up the same amount for an additional receiver. Then the cables won’t plug into another receiver and need adapters.
“Last spring, it took about three weeks and a lot of phone calls to get it all together. And, we still can’t do all that I’d like such as integrating with our record keeping.
“Another problem developed when my accounting package supplier, Farmworks, collaborated with another supplier, Ravens, to develop a guidance system called Guidemate.
“I already owned a Trimble receiver with a lightbar and an Agco receiver without a light bar so I thought I could equip the Agco with the new guidance system. This would allow me to use the Farmworks package to integrate with my accounting system.
“Yet, when I tried connecting the various components, they didn’t work even though I gave the vendor the specifications.
“What we need basically – and maybe we are slowly coming to it – is a center where information is shared by manufacturers so they can integrate their systems.”
“A while back, in your Best/Worst Buys, someone said how much they liked “Torx” screws. I wondered at the time how the guy managed to get his pants on in the morning. The “Torx” screw must have been invented by a politician or a bureaucrat because it has to be among the stupidest ideas of the 20th Century.
“The efficiency of any moment of rotation is proportional to the distance from the center of the item being rotated to the means of applying the necessary rotational pressure, so that the best efficiency on a screw, for instance, is a thumb screw or wing screw followed by a square head followed by a hex head followed by a slotted head followed by the recessed heads like the Phillips, Allen, and the Square Drive. The Torx head is the least efficient because the recess is the smallest relative to the size of the screw, added to the problem of the many contacts with the driver.
“I just finished drilling out six screws that refused to come out. They were Torx head screws and I used up my entire vocabulary of cuss words. It is quite difficult drilling out small diameter screws without mucking up the threads of the holes.”
Glenn’s the satisfied owner of a 2001 White LT 2150 Hydro-lawn tractor equipped with a 46-in. mower deck. “It has more than 220 hours on it with no problems. My only expense has been for oil and filters.”
“My 1979 New Holland 4630 tractor is highly maneuverable and just the right size for everything I do.”