Chrysler: what farmers say
50 reports in FARM SHOW · 46 Best Buys5 Worst Buys
Chrysler (general)
32 Best Buys2 Worst Buys“My 1990Chrysler New Yorker car was my worst buy. I had to have the heads on the engine changed four times in the first 60,000 miles. The repair costs were covered by the warranty but it was still a nuisance.
“My best buy is my 1982 Case 2390 tractor. It has 2,800 hours on it with no problems and just keeps on running.”
Norbert Hogbin, Joice, lowa: “My best buy is my 1991 Dodge Dynasty which I bought as 4 program car with 15,000 miles on it, It now has 102,000 miles. The only repairs have been to a thermostat oil pressure sending unit and a speed sensor. The car still has the original exhaust system, shocks, and brakes and all its original belts and hoses. The original tires went 72,000 miles and were never rotated, and the front wheels have never needed alignment. change the oil and filter about every 3,000 to 4,000 miles and have never had to add oil between changes. This is my fifth Chrysler vehicle and they’ ve all gone over 100.000 miles with no major problems.”
Duane E. Haney, Chenoa, IIl.: “My 1994 Dodge Ram 2500 4-WD rides and drives better than my Mercury station wagon, It has ample power to pull a 31-ft. Sth wheel camper weighing over 5 tons empty, My only criticism is that when I down-shift out of cruise control, it jumps down two gears, then quickly up one. Chrysler should just leave the cruise control off altogether.”
Elbert Proctor, Catlett, Va.: “One of my worst buys was a 1985 Buick Century, It was a lemon from the start. After overhauling the engine three times, I sold it. P've since had much better luck with Chrysler products. “I'm also disappointed with a Tri-H mower blade that ordered last August after reading about them in FARM SHOW, waited two months to get them. Then I called the company and was told they would get the blades right out to me, waited another six weeks, then called again. That time I was told they'd get the blades out to me first thing Monday morning. Well, now it's spring, and 'm cutting grass with an old blade because still haven't gotten my Tri-H blades. Am I the only one in this situation?” Editor’s note: Tri-H president Joseph Hladik says the company had production problems early on due to tremendous demand for the innovative new mower blade, but that they're getting caught up. “We appreciate the patience of thousands of FARM SHOW readers who've sent orders,” says Hladik, adding that the company is catching up on back orders, “Everyone who ordered a blade will receive it.” Contact: Tri-H Corp., Rt. 1, Box 145-A, Hennessey, Okla, 73742 (ph 405 853-4563 or 4561).
Henry Nelson, Towanda, Kan.: “In 50 years of driving my 1993 Dodge Intrepid is the worst car I've ever owned. When driving down a fresh-graded gravel road, dust comes in everywhere. After about 50 miles, you can write your name on the rear armrests in dirt so thick you can’t tell what color they are. Chrysler told me it was the car’s design and there was nothing the company could do. In trying to diagnose the problem, we drove other Intrepids, Concords and Eagles and the same thing happened, so I traded it off after owning it for just a year and a half.”
Derrell Jones, East Prairie, Mo.: Derrell nominates one Chrysler vehicle as his best buy and another as his worst. “My 1988 Dodge Ram 50 pickup gets 25 mpg, has 170,000 miles on it, and uses no oil, It still has the original exhaust system. I’ve only spent $29 on repairs in six years. “My 1994 Plymouth Voyager van is another story. It uses a qt. of oil every 800 miles with just over 21,000 miles on it. Neither the company nor dealer will do anything about it.”
Donald Borton, Delavan, Ill.: “My 1991 Chrysler New Yorker is just a good all around car backed by a long warranty. We had a problem with the fuel pump at 90,000 miles. It was replaced right away at no cost to us. The car gets good gas mileage and has a lot of standard extras.”
Herman Stovall, Kemp, Texas: Herman's best buy is his new Massey Ferguson 396 tractor equipped with a 1000 series 6-cyl. engine. “No bells and whistles here. Just a 12-speed forward, 4-speed reverse transmission, 4-WD, and comfortable cab. Hydraulics have adequate power and speed. It cost $4,500, a lot less expensive than a Deere 85 hp tractor with a 4-cyl. engine.” R. Leigh Catchpaugh, Sherwood Park, Alberta: “My all-time worst buy was the Dodge Dakota pickup I purchased in 1990. Everything went fine until my wife and were visiting in the States about a year ago. The engine began to cut out, so we changed the fuel filter which helped until that evening. When the problem recurred, we began taking it to dealers all over Washington state since the truck had less than 49,000 miles on it and was still under warranty. That began nearly a year-long series of visits to dealers in the U.S, and Canada without any luck. The problem - whatever it was - created a safety hazard on the road so Leventually sold it, What's most disgusting is that the Canadian Chrysler Corp. officials contacted didn’t seem in the least bit interested in helping us with our dilemma. The whole ordeal cost my wife and me great anxiety, loss of vacation time and money.”
Murray Woods, Linden, Alberta: A 1985 Nissan Kingcab truck equipped with a powershift transmission heads Murray's “best buy” list. “It has over 150,000 miles with only normal maintenance. The only modification made was to install a carburetor kit. It still runs great. “My 1986 Deere 4650 tractor is reliable and hasn't had any problems. It has a quiet cab with a comfortable operator platform.” On the “worst buy” side, “One year ago we bought a new Chrysler mini-van, The van works great but the Goodyear tires on itarea joke. Within 2,500 miles the sidewall blew outon one tire and within 12,000 miles the other three tires wore out, Chrysler said the tires weren't their responsibility and sent me to Goodyear. Goodyear indicated these were ‘cheap’ tires and wouldn’t back them. I'm disappointed that Chrysler and Goodyear would endanger their reputation and the safety of customers by putting such poor tires on a new vehicle.”
John Thorn, Bigfork, Mont.: “My sister-in-law bought a new Chrysler New Yorker in 1987 and shortly afterward the dealership was sold. When she took the car back for repairs under warranty, the new owners told her that they aren't responsible for the car because they didn't sell it to her. The car has had problems with the heater and air conditioner ever since it was almost new. They replaced a sensing unit twice at a cost of about $100 each time. It still doesn't work right. Also if the car sits for a few days, the battery loses power - even a new battery.”
Larry T. Denton, El Campo, Texas: Larry's “worst buy” is his 1990 Dodge pickup equipped with a Cummins engine. “I drive about 5,000 miles a month, but for the first five months after bought this pickup I drove a total of only about 8,000 miles because it was in the shop most of the time, It had problems with the speedometer, air conditioner, transmission, and rearend, and the tires vibrated a lot. I replaced the speedometer, The transmission wouldn't go into reverse without being forced so I also replaced it. When the airconditioner wouldn't cool properly, the dealer suggested that I tint the windows. I had to change four wheel rims and ‘shave’ the tires three times, but the tires still vibrate. The rear end burned up and took two weeks to repair because the dealer couldn't get parts. Chrysler has paid for most of the repairs so far. The engine works great when I get to drive it.”
Edward Huppert Jr.,Salem, Neb.: “It's one of the best buys I've made in a long time,” says Edward, pleased owner of a Case-IH 1660 combine. “It’s a wonderful machine to set and to operate. I’d never buy anything else. I had been a New Holland combine owner.” Ear! Hanson, Newfolden, Minn.: Earl's 1985 Chrysler New Yorker car has more than 100,000 miles. “It still runs and looks like new, making ita best buy. It’s equipped with a 2.2 liter turbocharged engine. “My 1982 Case 2390 tractor is also a best buy. I bought it used in 1986 with 875 hours. Now it has 1,875 hours with no problems.”
Norbert Hogbin, Joice, Iowa: “My 1988 Dodge Dynasty is bothabestand worst buy. On the plus side, the performance of the V6 Mitsubishi engine is excellent. Fuel economy is satisfactory at 22 to 26 mpg. Rides and handles very well. On the negative side, there’s a problem with the fuel injection system that causes extreme hesitation when starting out with a warm engine. The dealer says that’s normal, but I don’t believe it, At 30,000 miles the fuel pump failed. At42,000 milesan oil seal failed causing loss of all the oil in about 10 miles. I’ve driven Chrysler products for many years and was always pleased with them, but the quality control has really fallen off.”
Ralph Arnold, Keosauqua, Iowa: His 1989 Dodge Arics automobile heads his “best buy” list. “It isn't a Chrysler New Yorker, but it’sa good little vehicle that gets 25 to over 30 mpg depending on length of drive.” e Robert's “worst buy” is his 1982 GMC 350 diesel pickup. “The brakes failed after 4 months and the engine, rear end, and transmission went out with less than 40,000 miles, have a lawsuit against the company.” His “best buy” is his 1986 Ford F-250 diesel pickup equipped with a4-speed transmission which he uses to pull a 26 by 7 1/2ft. gooseneck trailer. “It’s economical to run and has been trouble free in 142,000 miles.”
Frank Ward, Vici, Okla.: “My 1989 Dodge diesel 3/4-ton pickup equipped with a Cummins engine is a best buy. It gets 20 mpg and is by far the best diesel engine offered in a pickup. Pulls loads super well. Thanks, Dodge-Chrysler.”
Alfred Rod, Sublette, [ll.: Carl is happy with his Iveco truck but he has received poor service. “This truck has a Chrysler automatic transmission, and the transmission cooler is run by an electric motor. When the wiring harness shorted out, they couldn't get parts and didn’t know how to wire it back up. We had more problems when the transmission started to act up.”
C.C. Schramm, Payson, Utah: “We like our 1987 Kelly Ryan 9 to 10-ft. silage big bagger. “There’s no tunnel to clean and it bags silage faster, tighter and smoother than any bagger I have ever used. like the bagger I bought so much I now sell them.” Also on the positive side, “My 1982 Chrysler Lebaron is as good a car today as when we bought itafter over 150,000 miles of wavel. It just refuses to wear out.” Schramm’s “worst buy” is the grass catcher on his Deere riding lawn mower. “Lf grass is shortand bone dry, itmight work butif the grass is 3 to4 in. long and growing, forget it. It'll plug in the tube. All lever got from the dealer was a laugh anda smile. It's a worthless piece of junk,”
Jerry Barnes, Danville, Ill: “In 1985 I bought a new Chrysler LeBaron witha 2.6 liter, 4 cyl. engine. The engine on this car never ran right. Although it would start good and run down the road fine, you never knew if it would accelerate at a stop light or cough and die. After many return trips to the dealer and near misses at 4-way stops, I traded it fora 1987 Chevrolet Celebrity with a 2.8 liter V-6 engine which is a nice car with a good engine. “Talso like my 19874WD Chevrolet 1ton pickup with 454 engine. I'd owned a 1983 Chevy 1/2-ton with a 305 engine but it was always short on power. With the new truck we have plenty of power and load “I've had it for 9 years and it's still a reliable machine," capacity. Can pull heavy loads with no problems. “Another best buy has been an International 1460 combine. I've had it 9 years and it’s still a reliable machine that’s relalively easy to work on. It may not have all the advanced gadgets as the new ones, but it doesn’t have a payment book in the cab either.” Jim Sherman, Andrews, N.C.; “The money I've spent trying to solve adaptor plate, heat and engine problems has cost more than any fuel savings | might have received had I got any,” says Jim, disappointed with M3 and MS5 Fish carburetors. “The manifold adaptor plates warped, allowing loss of vacuum. Also, the lines, aa t Buys ) pump and float bowl are so heat sensitive that fuel tends to vaporize in the line before it’s in the carburetor bowl, even when wrapped in insulating tubing.” George Stewart, Fayetteville, Tenn.: “My 1987 Case 885 tractor with 2250 loader has its plusses and minuses. It has plenty of power and works well to clean out low barns. Minuses are the hydraulic control location, drawbar height, and case of filter change and oil addition with the bucket on. Also, the steering radius is more than | like. Loader is excellent for moving round bales and manure handling. [ also like the ease of mounting.” As “worst buy” he nominates his 1987 Isco hi-lift bale mover. “The bolts were grade two inthe third arm. They broke while picking up the first bale. The lift crimped 2 hydraulic lines on the tractor and the hinge points are built too weak. It works alright after replacing the grade 2 bolts with grade 8. ! “I do like my 10-20 Grain-O-Vator with hydraulic controls. It’s worked well with no major breakdowns. My New Holland equipment, including a 315 baler with model 80 thrower, 512 manure spreader and 478 haybine all work well. They've been trouble-free and the haybine, bought new in 1976, cuts 300 acres a year and still does a good job of cutting and conditioning hay. The only problem has been the chains that drive the rollers.” George also likes his 1982 International 800 4-row plate planter and Lifetime hydraulic hog trailer. “Planter’s seed placement and no-tilling ability have been excellent. The only problem has been the fertilizer drive chain and that the disk openers wear too fast. We've used the trailer almostevery day for six years with no problems.”
Alan Sloan, New Boston, Ill.: He names his 1985 Chrysler Fifth Ave. as "best buy". "Gets 23 to 24 mpg. and I've had few problems with it. I would like to see them put electronic fuel injection on their cars instead of carburetors."
Don Burgess, St. Thomas, Ont.: “Buying gas for this truck almost broke me, When got in touch with Chrysler consumer relations they told me it was normal. Therefore, sold it after having it for only two years,” says Don, disappointed witha “Buying gas for this truck almost broke me.” 1984 Dodge 200 pickup with 318 engine. He likes his 1987 Nissan with King Cab and automatic overdrive transmission. “This truck is perfect. There aren't any rattles and it gets good mileage. Transmission makes it easy to drive.”
Russ Twedt, Rudyard, Mont.: He nominates his 1985 Dodge Caravan with 2.2L engine as “worst buy” “Although this mini-van is a very good vehicle in most respects, it’s a deathtrap when there's any substantial amount of snow lying on the road. “It’s a deathtrap when there’s snow on the road.” Airflow buries the motor in snow and the air intake also fills up with snow, stalling the engine. Also, the throttle linkage has frozen twice on the highway. Although the dealer's service manager has tried everything he can to remedy this situation, Chrysler Corporation will not let him re-route the air intake or build a splash pan underneath, Numerous complaints to Chrysler have so far yielded no results."
Don Hermes, Oxford, Neb.: “So much for the new Chrysler Corp." says Don, upset with his 1984 Dodge D-150 pickup. “Gear shift lever had to be bent to get it in reverse and the transmission had a scraping noise and too much backlash. No vent in rear axle housing caused leaks and pinched wires caused electrical trouble in cold weather. The 318 engine takes more gas and has less power than 1972 model.”
Chris Williams, Comox, B.C.: ‘My worst buy is a 1981 Dodge Ram 250 pickup. Within days of purchase the 6-cyl. engine acted up so that it barely had enough power to pull itself along level ground, This condition changed from day to day depending on air temperature and humidity. Other problems were weak motor mounts and a hard-shifting 4-speed transmission. The dealer and company could not fix the truck so I sold it with only 15,000 miles on it. When I traded it I found that Dodge trucks were discounted by at least $1,000 even by Chrysler dealers.”
John W. Ward, Trobisher, Sask.: “' have a 1980 Chrysler Newport which runs great but has a very poor paint job and parts that get dull and can't be shined up. I have an older 1968 that still has a better paint job and looks better than this newer model. “TL also have a 1975 Steiger Bearcat Il. Its 3208 Caterpillar motor went out at 800 hrs. caused by a rubber hose on top of the tappet cover that got a hole in it. Now I replace this hose every year regardless of its condition. Also, the gears in the wheels went out last summer and it took 43 days to get replacement parts up to us here in Canada. Can't afford this kind of service.” Wayne Hofer, Dolton, S. Dak.: Wayne's happy with his television satellite receiver dish from Automation Techniques, a model GLR 560 with a 10%-ft. Hastings aluminum dish and a Hytek programmable antennae control, “I bought this system last spring and have been very pleased with it. It gets more than 80 channels plus many radio stations."
Dave Akerberg, New Lisbon, Wis.: “My ‘best buy’ ever is an 806 International that bought new in 1969, It has almost 8,000 hours on it and has never been overhauled. Another good buy is my International 2 + 2 3588 tractor. It's easy on fuel, has plenty of power, lots of traction and a comfortable cab. My wife and son like it too. “Another good purchase was a 1983 Chevy K-30, 4-WD diesel pickup. I've only replaced 3 glow plugs. It’s a real workhorse. Gets 22 mpg on the highway and 17-18 mpg pulling 350 bu, wagons.” Dave nominates his model LD Liquid Brush power washer (550 Ibs. pressure) as his worst buy. “It will not prime properly and the hoses won't stay on the wand or the washer. The pressure pops them off. The soap holder cracked and broke and the trigger sticks on. Recently, I read where there’s an electrical hazard. We still haven’t had anyone contact us as to where we get the kit to remedy this," pleased with his International SP 4000 swather. ‘We've used this machine for three seasons cutting hay with the hay header, then changing to the grain header and swathing grain. No breakdowns and it handles well. Vision is also good.” Terry Fischer, Glen Ullin, N. Dak.: “T know one thing — if we ever buy another combine, it will be a Deere. Our pull-type 6601 Deere has covered 10,000 acres and we've only had to replace a couple of bearings besides putting in new cylinder bars, feeder chain and picker belts. In the last couple of years, we haven't had any breakdowns or plugging problems. “All the rest of our ‘best buys’ are also Deere equipment. We have a 4440 tractor that's been super. It has 2,900 hours on it and the engine's never been touched other than a tune up last fall. It has plenty of power, is quiet and hardly uses any fuel. We're also happy with our 4240 tractor and our 9000 series grain drills. Plus, we think our 2320 swather is really state-of-the-art technology. We especially like the floating header and the large and roomy cab. In 1,500 acres, we never had a breakdown. Although the Chrysler engine leaked oil for awhile, they were able to fix it.”
Victor Koop, Dundurn, Sask.: He's pleased with his International SP 4000 swather. ‘We've used this machine for three seasons cutting hay with the hay header, then changing to the grain header and swathing grain. No breakdowns and it handles well. Vision is also good.” Terry Fischer, Glen Ullin, N. Dak.: “T know one thing — if we ever buy another combine, it will be a Deere. Our pull-type 6601 Deere has covered 10,000 acres and we've only had to replace a couple of bearings besides putting in new cylinder bars, feeder chain and picker belts. In the last couple of years, we haven't had any breakdowns or plugging problems. “All the rest of our ‘best buys’ are also Deere equipment. We have a 4440 tractor that's been super. It has 2,900 hours on it and the engine's never been touched other than a tune up last fall. It has plenty of power, is quiet and hardly uses any fuel. We're also happy with our 4240 tractor and our 9000 series grain drills. Plus, we think our 2320 swather is really state-of-the-art technology. We especially like the floating header and the large and roomy cab. In 1,500 acres, we never had a breakdown. Although the Chrysler engine leaked oil for awhile, they were able to fix it.”
Gene S. Peters, Little Rock, lowa: “Our 1981 Case 2290 tractor has been as trouble-free as you could expect and is priced in a range that we can easily justify. Dealer support is great. We own two other Case tractors and have had similar good experience.” Albert Patterson, Sussex, New Brunswick: He's pleased with his Miller electric welder bought in 1978. “Works great and ‘it's the best money-maker on the farm because we make much of our own equipment,” Levon Schlenz, «Brockton, Mont.: Levon’s pleased with his Chrysler Sth Avenue. “It handles well, gets good gas mileage and has excellent workmanship.”
Roger Lee, Franklin, Minn.: ‘‘My best buys are my 10 Schweiss elevated calf stalls with Tenderfoot pads which I purchased from Schweiss Manufacturing, Fairfax, Minn,,”’ reports Roger. “Our calves are kept in the stalls from birth to 30 days of age, at which time they're weaned, We freshen 100-plus Holsteins annually and, in the two years we've had the stalls, our death loss has been at zero, and the number of calves we'd had to treat can be counted on one hand. “Also a best buy is our Chrysler cars. We bought our 1969 Dodge station wagon with a 383 cu. in. engine and it’s still running strong after 167,000 mi. of service with no major repairs. In fact, the valve covers have never been removed. Our 1975 Chrysler Cordoba has 114,000 miles with the same results, and our son's 1970 Plymouth Barracuda has more than 80,000 miles. “My worst buy is a 1978 Honda ATC 90, It was next to impossible to keep the engine and transmission operational at the same time. Dealer service was a rip-off which would result in a several hundred dollar repair bill annually. Needless to say, the ATC has been gathering dust. The dealer must have run out of suckers because he was forced to close recently.”
James R. Urch, Drumheller, Alberta: James has had good luck with his Butler 48 by 96-ft. Farmstead I metal building. “It is much stronger and better designed than other steel buildings and the local dealer helps out in every way,” he reports. ‘We're also very pleased with our RCA portable video camera and recorder, It lets us control the TV during the busy seasons and watch programs and movies when it rains or such. It brings us city benefits in rural areas, Steve Vaadi, Jr., Lafargeville, N.Y.: ‘“‘T have an old Massey Harris Super 101 Twin Power with a 6 cyl. Chrysler engine that I believe cannot be beat,"’ says Steve. “It has been a tough reliable tractor. It has thousands of hours on it without any major breakdowns.” Steve is also pleased with his Homelite Super XL chainsaw. ‘‘l traded in my older Super XL for it. I've logged for quite a few years and cut wood for my own use, too. I'm pleased with the handling of my Homelite saw and its dependability. It starts easily and has no maintenance problems, also have an older XP 1000 Homelite saw that has never given me problems.”
Bruce Lovdahl, McGregor, N. Dak.: ‘My best-liked product has to be the Chrysler slant six engine,” says Bruce. “I've got three vehicles with the engine. One, a 1964 Dodge Dart, has 190,000 mi. and the engine has never been touched, including the original pumps. The others area 1973 Dodge pickup with 65,000 miles, and a 1972 Plymouth Duster. Neither has ever had the valve cover off. Mileage on the cars has been as high as 27 mpg.”
Norman Heitstuman, Uniontown, Wash: “I have very little Deere equipment because of the high initial cost, plus the high cost of maintenance after the sale,"" Norman told FARM SHOW. “Deere and International are constantly figuring ways to build more of their own parts so they havea. captive customer and can charge most any price they want for parts. “T have a Gleaner MH combine and am really happy with it. A good performer that's easy to work on and cheap to maintain since can buy many parts at my local NAPA parts store, or bearing and power transmission store. “T have been reading with interest the FARM SHOW stories and letters concerning Ray Stueckle’s combine modifications,’ Norman continued. “I've known Ray personally for years and support him 100%, After all, many of his ideas boil down to putting combines in order the way design engineers intended them to be built. The problem starts when production engineers and accountants have other ideas to cut costs. “I know fora fact this goes on since had a Massey-Ferguson 655 windrower that caused lots of trouble. In talking with the factory engineers, and after two years of recalls, I finally traded it for a Hesston 6400, the “Rolls Royce” in haying. It's built like a fine watch, and burns about half as much fuel as the MF 655 did even though both have the Chrysler 255 6-cyl. engine. Many shortline companies have machines and service as good as the big ones, like Deere and IH."
Clarence Folkerts, Carleton, Neb: Clarence Folkerts, Carleton, Neb., in nominating the ‘‘best buy" he’s made this year. His nomination: A “hybrid” planter, consisting of an Orthman folding toolbar, bed shaper and two six-row International Harvester Cyclo blower modules. “It’s a magnificent piece of equipment for getting a lot of corn planted quickly without trouble,’ Clarence noted, adding that “the excellent cooperation from the IH dealer in Lexington made it possible.” Another “hybrid” earned a “best buy" vote from Murray Peterson, of Stromsburg, Neb. He built a homemade crop drier using a combination of Behlen and Neco products; “We put up a 34 ft. Behlen bin three rings high and without a roof. It has a false bottom floor with a pit underneath for even air flow and a 48 in. Behlen fan powered by a 440 Chrysler engine. We put in a Neco ‘dry flow’ dryer system. It will dry 600 to 700 bu. per hour and we only have to run it during picking hours.” Here’s what other randomlyinate sUYS selected FARM SHOW readers responding to our latest buying survey had to say about the “best” and “worst new products they've purchased recently: “['m very happy with your magazine,’ reports
Murray Peterson, Stromsburg, Neb: Murray Peterson, of Stromsburg, Neb. He built a homemade crop drier using a combination of Behlen and Neco products; “We put up a 34 ft. Behlen bin three rings high and without a roof. It has a false bottom floor with a pit underneath for even air flow and a 48 in. Behlen fan powered by a 440 Chrysler engine. We put in a Neco ‘dry flow’ dryer system. It will dry 600 to 700 bu. per hour and we only have to run it during picking hours.” Here’s what other randomlyinate sUYS selected FARM SHOW readers responding to our latest buying survey had to say about the “best” and “worst new products they've purchased recently: “['m very happy with your magazine,’
Chrysler Town
3 Best Buys1 Worst Buy“I inadvertently damaged the rotor when installing a Pertronix electronic points and condenser eliminator kit on my 1953 Deere 40C tractor (www.pertronix.com; ph 909 599-5955). After calling the company’s technical support personnel and explaining the problem, they sent a new rotor at no charge. Now the tractor has never started better. I wish I had bought this kit 10 years ago.
“We’ve put more than 261,000 miles on our 2006 Chrysler Town and Country van, and the only major repair we’ve had was to replace the alternator at about 230,000 miles.”
“My worst buy was my wife’s 2005 Chrysler Town and Country van. At 24,000 miles, when the 3-year warranty had already expired, the driver’s side window motor had to be replaced at a cost of more than $400. The rack and pinion gear started leaking at about 35,000 miles and the repair would have cost more than $600, but fortunately the shop replaced it at no charge. At 39,000 miles the water pump started leaking, and that cost more than $200 to resolve. Now the van has just over 40,000 miles on it and the remote door locks don’t work.”
“My 2006 Chrysler Town and Country van rides nice and is fuel efficient. This is the third one I’ve owned over the years.
“My 1976 Allis Chalmers 185 tractor is economical to operate and has never had a complete overhaul. No problems.”
“It has a lot of towing power, is dependable and is a pleasure to use,” says Ken about his 2008 Polaris Ranger 700 utility vehicle. “I’ve always used 4-wheelers in the past, but with a utility vehicle I don’t have to strap things down. I use this machine to spread grass seed, spray weeds, haul trash, drag small trees and limbs, haul firewood, etc.
“My 2006 Chrysler Town and Country van has been nothing but trouble. The speedometer is off by 10 percent, the battery loses its charge if we don’t drive it for a few days, the back-up sensors aren’t dependable, and so forth. Dealers haven’t been able to resolve the problems.”
Chrysler Concorde car
2 Best Buys1 Worst Buy“My 2006 Deere 6420 4-WD tractor equipped with a 640 front-end loader has been trouble-free. The loader bucket and the bale spear change easily. The tractor has a small turning radius so it’s easy to maneuver in tight areas. The 4-WD lets it go through deep snow to get round bales to my cattle. I did have some problems with the cab door gaskets freezing to the door frames, but I solved that problem by wiping anti-freeze on the gaskets and frames. A small amount is all it takes.
“My 2006 Chevrolet Impala SS has had a lot of minor mechanical problems. The V-8 engine has a lot of power, but the fuel economy is just okay at 22 to 24 mpg. The 4 to 8-cyl. switching option seems to make very little difference in fuel economy. The engine uses oil, and with about 125,000 miles on the car I’m already on the fourth set of tires. I’ve been told this is a problem with all the SS models. I wish this car worked as good as my 1996 Chrysler Concorde, which has more than 200,000 miles on it.”
“I’m well pleased with my 1993 Chrysler Concorde car. It’s not rated very high by Consumer Report magazine, but my total cost for repairs so far is less than $500 (Canadian) which I think is pretty good.”
“My worst buy in an automobile in 65 years has to be our 1994 Chrysler Concorde. The excessive wind noise around the doors and windows, as well as the road noise, is very tiring. We’ve taken it back to the dealer four times and contacted Chrysler Corp. but nothing has been done about it. My brother bought one at the same time and has had the same problem.”
Chrysler 300-C
1 Best Buy0 Worst Buys“I purchased a new Massey Ferguson 1429 tractor/loader in 2003. I have 3,500 hr on it…”
Chrysler Aspen SUV
1 Best Buy0 Worst Buys“My best buy is my 2007 Chrysler Aspen SUV. It’s equipped with a 5.7-liter V-8 Hemi engine. I bought it used with 75,000 miles on it and it now has around 165,000 miles. It pulls my stock trailer easily. Trouble-free. Great vehicle.”
Chrysler Dynasty
1 Best Buy0 Worst BuysBob Otto, Mapleton, Iowa: “We use our 1991 Honda 300 4-wheel ATV for lots of jobs such as herding cattle, mending fence, checking crops, carrying newborn calves, and spraying for weed control in pastures and around the yard. With 4-WD it can cover any terrain, wetor dry. Very reliable.” Paul Bertrand, Ileda Grand Calument, Quebec: “My 1991 Chrysler Dynasty is a comfortable car that’s good for both county and city driving. Handles rough gravel roads very well. The warranty is longer and covers a lot more than warranties offered by most other companies.”
Chrysler Intrepid full-sized car equipped
1 Best Buy0 Worst BuysDoug nominates his son’s 2001 Chrysler Intrepid full-sized car equipped with a 2.7-liter, V-6 engine as his “best buy”. “He bought this car used one year ago with about 100,000 miles on it for only $3,500. Since then he has put another 20,000 miles or so on it with no problems. It gets 35 mpg on the highway, which I think is good for a full-sized vehicle. This is the only Chrysler car we’ve owned in more than 65 years, but it’s by far the best. My son bought it because he drives 32 miles to work and needs economical transportation.”
Chrysler Pacifica 4-WD car equipped
0 Best Buys1 Worst Buy“My 2007 Chrysler Pacifica 4-WD car equipped with a 4.0-liter engine has room for six passengers. The company quit making this car in 2008, which was a mistake because it has a lot of power and is a joy to drive.”
Chrysler Pacifica Touring
1 Best Buy0 Worst BuysHe’s happy with his 2018 Chrysler Pacifica Touring Plus minivan. “The Pacifica van has many improvements over the company’s Town & Country models. It’s more fuel efficient, is quieter, and is roomier with more storage area. It also has a very comfortable ride. My wife loves it.
“My 2000 Jeep Cherokee Sport has about 230,000 miles on it but still runs great and doesn’t use any oil. I use it to plow snow and with a trailer to haul snowmobiles, and it also makes a great hunting vehicle. Too bad they quit making this model.”
Chrysler Reliant k-car
1 Best Buy0 Worst BuysTom Probst, West Liberty, Iowa: Tom says a 1990 Case-IH 7110 Magnum tractor heads his “best buy” list. “I’m extremely pleased with it. It casily pulls a 22-ft. diskchisel plow without lugging down and regains rpm’s very quickly, The powershift transmission is smooth and has speeds where I need them. It’s a pleasure to operate. The cab is quiet and well designed with great visibility. “J uaded a Massey Ferguson 2745 tractor for the Magnum. I wish I had never seen that tractor. I could afford it when I bought it, but in the end the down time and repair costs made it too expensive to keep.” Marcel J. Dufault, Haywood, Manitoba: “I’m a crop adjuster so I travel a lot over rough fields and country roads. I find thatmy 1989 Chrysler Reliant K-car is abest buy. The 2.5-liter engine has plenty of power and is fuel efficient. It drives comfortably and handles well on unpaved country roads. The 5-speed manual transmission makes it nice for driving over fields. It has over 35,000 miles with no problems,”
Chrysler Town Country mini van
1 Best Buy0 Worst Buys“My 1999 Chrysler Town & Country mini van is a reliable, dependable vehicle. It has about 365,000 miles on it, and I’ve only spent about $4,500 on repairs. The 3.8-liter, V-6 engine has never been worked on. I change the oil and filter every 10,000 miles and add STP oil treatment to protect against engine wear. I use regular 5-20W oil.”
Chrysler minivan
1 Best Buy0 Worst Buys“I’m 79 years old and losing power, but my 1952 Ferguson T0-30 tractor isn’t.
“My 2005 Chrysler minivan still looks and runs like new.”
Chrysler vehicles
1 Best Buy0 Worst Buys“Since 1967 I’ve owned 12 Chrysler vehicles including 4 cars, 4 vans, and 4 trucks and have had good luck with all of them. I can’t say that for the GM vehicles I’ve owned.”
Read every report in full
FARM SHOW has run reader Best & Worst Buys since the beginning.