New Holland 855 round baler
What FARM SHOW readers say · 4 Best Buys3 Worst Buys · Tractors
New Holland 855 round baler
4 Best Buys3 Worst BuysWendell Suelter, Lincoln, Kan.: “My 1979 Allis Chalmers 7045 tractor has performed well above expectations. Excellent lugging ability and handles well. “Lcan’tsay enough good things aboutmy 1991 Dew Eze flatbed. We use it to haul round bales and doa lotof other jobs. It's the most valuable tool on our farm, “My 1991 New Holland 855 round baler is the most underated baler on the market. A 10-year-old child could operate it.” On the minus side, Wendell lists his 1989 Hesston 5585 round baler. “It spent as much time in the shop as it did in the field. The pickup attachment was a disaster, The bearing lock collars weren’tsettightenough at the factory and belts were poor quality. It wasn’t a dependable machine. “My 1989 Ford F-250 4-WD pickup equipped with a diesel engine has been a nightmare. Almost every part on it, except “Tt's one of the most underated balers on the market. A 10-year-old could operate it.” for the engine, failed before it even had 100,000 miles. I bought it used with no warranty coverage. I'll never buy another used pickup again, partly because I don’t want to go without a factory warranty.”
Orvis Byklum, Grygla, Minn.: “My 1974 Case 1175 tractor has over 3,000 EE aT aE “The dealer did a good job repairing it. But what will happen next?” ae. an hours. I had to replace one throwoutbearing at 300 hours, Since then it has requiredonly routine maintenance, “My worst buy is my New Holland 855 round baler. The maindrivebeltbrokedown Editor’s Note: We received a lot of response to last issue’s “worst buy” report from Emily Coffey, Arvada, Colo., about her 1990 Ford-New Holland 276 bi-directional tractor that burned up. Jimmy Byers, Brinkley, Ark., sent us the photo above that shows a blown-out battery (on right in photo) in his 1992 Ford New Holland 946 340 hp. 4-WD, Byers thinks the battery hold-down brackets caused the blow-out. “If Emily had the same hold-down system on her tractor, and the batteries blew out, that could have caused her fire. The problem is that the brackets are positioned too close to the battery posts. They corroded and then shorted out. The end blew out of one battery. We had battery acid all over. Our dealer didn’t wantto repair the damage but after I threatened to sue, he did.” Ed Swanson at the Minnesota Department of Transportation, St. Paul, Minn., says one of the department's 1992 Ford New Holland 276’s burned up this fall. “Tt went up so fast, the operator barely had time to get off. We’re concerned because we own a number of these tractors. We don’t want anyone to get hurt and we don’t want to lose equipment.” Swanson says he thinks the fire started in the articulation area and may have been caused by an electrical problem, but no investigation has yet been carried out. Galen Travis, Burlington, Colo., who once had a fire beneath the cab on his 1985 Versatile 276, is convinced the fire problem is caused by friction between a drive shaft and crop residue that packs tightly into the area between the bottom of the cab and the frame of the tractor. “Trash packs in there so tight it’s difficult to get it out,” says Travis, who came up witha modification kit that raises the cab up a few inches (see story on page 29 in this issue).
Deborah McCollum, Lockport, N.Y.: “Our New Holland 855 round baler has a lot of capacity which, combined with autowrap, makes baling hay quick and casy even in a bad year. “Our worst buy is our 1992 Chevrolet S10 pickup equipped with a 2.5-liter 4-cyl. engine. Ithas had hesitation problems from the startand, when itrains, water comes into the cab through the vents.”
Otis Lee Berry, Cunningham, Kent.: “My 1990 New Holland 855 baler is a worst buy. I bought it in May of 1990 and the first time I used it the pickup teeth bent inside the guards. My dealer didn’t have enough new teeth on hand so I had to drive 200 miles to find some. Later I lost 75 acres of rented hay because the baler was at the shop for three months even though I called the company service manager three times. They finally brought it back last January.”
John Penner, Morden, Manitoba: John has had trouble with his 1986 New Holland 855 round baler. “Its pickup is poorly constructed and the shear pin set up is a pain. It would be a lot better if you could replace shear pins on the pickup’s belt drive rather than have to repair the chain drive. Also, the drum is too large for smooth feeding and the pickup teeth are poor quality.”
Jimmy Neuby, Ardmore, Tenn.: “Our New Holland 855 baler will not have the life expectancy of our old New Holland 850 baler. The auto-tie and twine cutter is not too good and they’ve cheapened up the baler by lightening up the pickup and eliminating the slip clutch, The gauge wheels on the pickup are not well-supported and, in general, everything is built lighter and cheaper.” On the “best buy” side, “Our Deere 4840 tractor has performed perfectly with little down time and expense. At 5,000 hrs., I’m very pleased.”
Keith Davidson, Chickasha, OkL.: “My 1985 Ford 7710 with front wheel assist had several problems that the dealer took care of but a new tractor shouldn't have this many things go wrong. The engine had oversize valves in standard guides, the load monitor had to be replaced and both rear wheel seals and one front seal leaked.” As “best buy” Keith nominates his New Holland 855 round baler. “There's never any problem starting a bale. Makes a good, solid bale.”
Own a New Holland? Tell FARM SHOW how it’s held up.
Your report could appear in a future issue.