Briggs & Stratton: what farmers say
22 reports in FARM SHOW · 14 Best Buys8 Worst Buys
Briggs & Stratton engines
7 Best Buys4 Worst Buys“I like my Homelite chainsaws and string trimmers, and my Black & Decker hand tools which include a circular saw, drill, sabre saw, and sawzall. Some of these tools are 40 years old but all of them are still going strong.
“I like Briggs & Stratton engines, and the 100-amp stick welder I purchased from Fingerhut about 40 years ago still works great.”
“I like my 2012 Graveley Z34 zero turn riding mower equipped with a Briggs & Stratton engine. Black & Decker hand tools are the best I’ve used. I’ve had good luck with Homelite chainsaws and trimmers and their outdoor power equipment. I’ve had to make minor repairs to Briggs & Stratton engines, but I still think they’re the best all around engine.”
“I never buy a lawn mower, garden tiller or any other small equipment unless it’s equipped with a Briggs & Stratton engine. I’ve always found these engines to be reliable. I have a 1985 riding mower equipped with a Briggs & Stratton that never fails to start and has required very few repairs. I did have to install a new switch on it recently, but parts are readily available and reasonably priced. Wal-Mart even sells some Briggs & Stratton parts.”
“Several issues ago you published a report about someone who was unhappy with his Howse bush hog. He said that every time he used the machine, something would break and he would have to weld it.
“As near as I can figure out, he must have bought a light duty model and tried to cut 3-in. dia. trees with it. Despite his ‘worst buy’ report, I purchased a new 6-ft. wide Howse 6100T mower, which I really like (ph 601 428-0841; www.howseimplement.com). It does an excellent job and is built tough.
“Also on the positive side, I’ve had good luck buying from the Surplus Center (ph 800 488-3407 ; www.surpluscenter.com). They offer ‘take-offs’, which means they sell brand new equipment that has been taken off a machine and is sold as parts. They sell engines, hydraulic hoses, pumps and motors, air hydraulics, tires, belts, gearboxes, wheels, and much more.
“I was able to buy some hydraulic hoses from them for only half as much as I’d have paid locally. I also replaced all the connections on my 1960 Case 310B backhoe with 3/4-in. quick disconnect couplers. I paid $22.95 for a complete set of male and female couplers. Locally, the same couplers would have cost more than twice that much.
“More recently, I purchased a 17 1/2 hp Briggs and Stratton vertical engine for my Murray lawn tractor for $439.95 plus $36 shipping UPS. I bought it on a Tuesday and it was delivered on Friday. Now, that’s service.”
Gary likes the Briggs & Stratton engine on his 2004 push mower. “The engine still starts and runs great, and even at full power it’s easy on gas and oil. I wouldn’t trade it for a new model.
“I used a new Murray Centura garden tractor to rototill a garden. Unfortunately, the oil seal on the tractor’s Tecumseh 4 1/2 hp engine failed after one use. I’m a small engine repairman but I won’t work on Tecumseh engines. They can’t take a beating like Briggs & Stratton engines can.”
“My father bought a Massey Ferguson 135 tractor new in 1965 and is still using it. This tractor has been used every year with very few problems. We use it with a Davis loader and a Bradco 802 backhoe. Both pieces of equipment have been on this tractor since 1984 and are used every year.
“My Black & Decker belt sander and Mouse orbital corner sander are worst buys. In my opinion both products, especially the Mouse corner sander, were made to be thrown away after very little use.
“Another cheaply made product is the starter motor gear on Briggs & Stratton 2-cyl. commercial engines. It’s made of plastic.”
“I’ve always liked Briggs & Stratton engines and have a lot of them working on my farm. Recently I found a use for an old engine that was laying around our barn for about 25 years. It was a 1965 2 hp model. I checked to see if the engine still had a spark and it did, so I added gas and to my surprise it started on the second pull. Not bad for a 44-year-old engine. I swear by the Briggs & Stratton brand.”
“The company wouldn’t stand behind the warranty,” says Terry, unhappy with the Briggs & Stratton gas engine on his lawn mower. “In June 2001 I bought a Swisher 60-in. trailing mower equipped with a Briggs & Stratton gas engine. I pull the mower behind a lawn tractor equipped with a 42-in. deck and use it to cut 4 1/2 acres of grass. From the beginning, this engine used 2 to 4 oz. of 30W Valvoline oil every time I cut the lawn, even though I followed the maintenance schedules and instructions in the owner’s manual.
“At the beginning of this year the engine started to use more oil and smoke was coming out of the exhaust. Then it started blowing oil up into the air cleaner. After replacing the air cleaner several times and trying 40W oil for a couple of mowing jobs, I made a wet and dry compression check. I found the pressure was a lot higher when the engine was hot than when it was dry. So I contacted Wisconsin Magneto, the warranty representative for Briggs & Stratton. The engine has a two-year warranty and was worn out in less than a year. Yet they said they wouldn’t honor the warranty because of lack of proper maintenance.
“I was given a phone number to call at Briggs & Stratton so that I could appeal the warranty rejection. Meanwhile, I had to buy a new engine so I could keep up with my yard.”
“My worst buy ever was a 1998 Sears Craftsman garden tractor equipped with a 42-in. mower deck and powered by a 15 1/2 hp Briggs & Stratton single cylinder gas engine. Two weeks after I bought it all the tires started losing air. Rather than traveling 45 miles one way to take the mower back to Sears, I installed tubes in all the tires. Then three weeks later the bracket that holds the bagger started to bend backward, which caused the bags to fall off the rear. I had to weld on a triangulated brace to fix it.
“The carburetor slowly leaked gas past the float valve and into the combustion chamber, which caused a hydrostatic lock. I had to remove the spark plug to drain the gas out so I could start it again. I also had to change the oil often because it was diluted with gas. I solved this problem by installing a fuel shutoff valve in the line.
“As for Briggs & Stratton engines, they’re among my worst buys, too. They used to be pretty good but not any more. I have a pressure washer equipped with an 11 hp Briggs & Stratton engine and a generator with an 8 hp Briggs & Stratton engine. On both machines, after the engines run for a few minutes the recoil starters lock up and rip the ropes right out of the housings.”
“My 1998 Remington 870 Express 12-gauge shotgun is my best buy. It works well, didn’t cost much, and has never had a malfunction of any kind. Disassembling and cleaning it is a simple job. My family and friends have used this gun as much as I have. I added an aftermarket sling to make it easier to carry on long treks.”
On the negative side, he lists the Briggs & Stratton vertical shaft engine on his Murray riding mower. “I bought this mower to cut a small yard. It soon developed an engine miss that got progressively worse. I took it to the nearest authorized Briggs & Stratton repair center. They made the repair but charged $50 to the retailer I bought the mower from. I was told the problem was that there was trash in the fuel. I have several small engines that use this same fuel with ‘trash’, and they all run well. To prevent the problem from happening again, I bought a new gas container and made sure the fuel was impeccably clean. However, the next time I used the mower the same problem happened again. I returned the mower to the authorized Briggs & Stratton warranty center. They charged me $50 this time, saying the problem was my fault.
“Before I left the dealer I tried to start the mower, but it wouldn’t start. The dealer kept the mower so that a factory representative could check it out. The rep said that the diaphragm in the carburetor had been damaged by dirt in the fuel. Then I took the mower home but couldn’t keep it running for even an hour. I finally junked the mower. I’ll continue to use the other Briggs & Stratton engines that I already have, but I don’t plan to purchase any more new ones. Factory support is poor at best.”
ADR trimmer mower (Country Home Products, Ferry Road, Box 89, Charlotte, Vt. 05445) rates as Duane’s “best buy”. “It has big wheels so it rolls easily and the 5 hp Briggs & Stratton engine starts easy and runs quiet. Lets me trim around anything with ease.”
Briggs & Stratton 18 hp engine
1 Best Buy1 Worst BuyA 1985 Subaru Brat ranks as Thelma’s “best buy”. “When I was an Army recruiter in West Memphis, Arkansas, I called a Subaru dealer in Memphis and the salesman described the ‘Brat’ over the phone and I bought it sight unseen. Now 25 years later it has more than 350,000 miles on it yet still runs like new, although it does need a new paint job. My husband, who I ‘found’ 10 years ago, is a Subaru technician, which helps!
The Briggs & Stratton 18 ½ hp engine on my 2007 riding mower is my worst buy. With less than 100 hours it threw a rod through the engine case. And at 25 hours the Sears mechanic had to service the valves.”
“It does an accurate job of planting in a minimum amount of time,” says Dale, pleased with his Deere 7000 4-row corn planter. “It’s also very reliable. “MyBriggs & Stratton 18 hp twin cylinder engine is my worst buy. The starter gear is made out of plastic and breaks about every three months. The engine doesn’t work well because it has a fixed jet carburetor. I drilled out the jet and added my own adjusting needle. Now it runs okay but only after I went through a lot of grief.”
Briggs & Stratton small engine gas
1 Best Buy1 Worst Buy“Our Toreq 12-yard push-off scraper is our best buy (Toreq Inc., 803 S. Barzen, Thief River Falls, Minn. 56701 ph 218 964-5272). It’s one of the only pieces of equipment I’ve ever bought that I’ve been able to hook onto and use without making any adjustments. It works beautifully. I couldn’t be happier with it.
“Another great product is Briggs & Stratton small engine gas treatment. It helps keep gas tanks and carburetors clean and even helps engines start easier.”
Bob nominates his 1993 Case-IH 5130 front wheel assist tractor equipped with a Case-IH front-end loader as his “best buy”. “It’s easy to start in cold weather, simple to operate, and has controls that are easy to reach. It also has a lot of hydraulic capacity. I’ve put about 4,000 hours on it in only four years.” On the “worst buy” side, he lists Briggs & Stratton single cylinder gas engines. “They require three or four times as much maintenance as other brands that I use, including Honda and Tecumseh.”
Briggs & Stratton (general)
1 Best Buy0 Worst Buys“I do repowers, and sometimes the customer comes up with stuff I don’t know about. I needed a new clutch, and a customer suggested I try one from Xtreme Outdoor Power Equipment. They make a billet- machined, heavy-duty clutch. It is a very nice unit.
“I agree with Dan Lien’s worst buy (Vol. 42, No. 1) that doing a repower on a garden tractor can be frustrating. Unlike Dan, I still do them, but I start out by telling customers that unless they have thousands of dollars to put into it, I won’t even start the job. If the tractor doesn’t have sentimental value and they’re not willing to pay, I won’t do it.
“I’m an aircraft and/or power plant certified mechanic, and I can’t estimate a price. I don’t know what I’ll have to modify outside of normal repairs. It takes extra time to design and engineer fixes to kits. Then there is the time needed to chase down parts.
“I had one customer who paid me $3,200 to replace a 17 1/2 hp. Kawasaki engine with a 20 hp. Briggs & Stratton on a John Deere 325. The shaft size was right, it bolted to the frame fine and the clutch went on with a new belt, pulleys and hydraulic hoses.
“However, the new engine kit came with a fuel pump, but not a voltage regulator. The Kawasaki regulator didn’t work with it. Luckily I had a Husqavarna in the scrap heap with the same type of plug, and it charged the battery fine. If not, I would have had to research model and part numbers and eaten up a lot of time chasing parts. How do you charge for that?
“If you buy the engine kit, you have to know what you are doing and have the skill level to install it. I’ve upgraded clutches and starter solenoids and swapped automotive-type fuse links for fuse blocks. I’ve also had to develop methods to lengthen choke and throttle cables.
“With the Briggs & Stratton, I also had to split out the throttle and choke cable. They came on one control, and you had to go to full throttle to get the choke. That means very high rpm’s, which isn’t good for a cold engine. I split the choke out with a separate knob so it could be on while the engine loafed along.
“Replacing cables can be tricky. On older machines the throttle cable often goes across the top of the battery, and acid fumes can rust and corrode it. I slide new throttle cables inside a plastic sleeve when they cross over a battery, which is a good idea for anyone to do.
“Fuel lines are a special problem, as they can be 20 years old and brittle. I’ve found I need to replace the entire line, not just patch it. I start at the tank and go all the way to the engine.
“Exhaust systems are another challenge. You have to know how to weld and fabricate tubing to make the exhaust fit where it needs to go.”
Briggs & Stratton 10kw auto standby
1 Best Buy0 Worst Buys“We love our 2010 Briggs & Stratton 10kw auto standby, propane-powered generator. We lose power quite often and have used this generator 16 different times to provide our home with full power. It has performed flawlessly. We bought the unit from our propane company, which took care of everything involved with installation.”
Briggs & Stratton 5 500-watt generator
1 Best Buy0 Worst Buys“Our 2006 Briggs & Stratton 5,500-watt generator is our best buy. Being without power is no picnic, as our parents found out when they lost their power. We bought this generator and avoided the trauma.”
Briggs & Stratton Elite
0 Best Buys1 Worst Buy“My 1995 DeWalt 14.4-volt cordless drill is my all-time best buy. It’s eight years old but will still drill 1/2-in. dia. holes in 1/4-in. thick plate steel. The only maintenance it ever required was a new chuck about five years ago. With just one spare battery pack, I’m ready for any drilling task on our place.
“My all-time worst buy is the Briggs & Stratton Elite series electric generator I bought last February. The first time I tried to use it, the carburetor iced up so bad the engine wouldn’t even run. When I called the toll-free help line, I was told to put the unit back inside the box and use it that way, cutting out a hole for the muffler. While this did work, it seems a strange solution. After using the unit for four months, it stopped working. I again called the help line and was given the name of the nearest warranty center. The generator sat there for two months without being repaired.
“I recently hauled the engine to another warranty center about 30 miles away and am curious how long it will be there. After several calls to the help line, I was given several excuses as to why no one will fix this generator, give me another one, or refund my money.”
Briggs & Stratton Intek Series small gas engines
1 Best Buy0 Worst Buys“Over the last two years, I’ve had excellent results with a pair of Briggs & Stratton Intek Series small gas engines. I use a 5 1/2 hp on my Oscar 28 sawmill and an 8 hp model on a Brave log splitter. I use both the sawmill and the log splitter intermittently, sometimes going three or four months without starting them. These engines always start easy and run smooth.”
Briggs & Stratton Storm Responder generator
0 Best Buys1 Worst Buy“My Woods 84-in. grading scraper is the best implement I’ve ever owned for driveway maintenance. It removes the washboard ripple very well.”
Myron isn’t happy with his Briggs & Stratton Storm Responder generator. “After about 20 hours of non-continuous operation, the motor seized up. I’m now looking at whole house generators and I won’t consider Briggs.”
Briggs & Stratton electric generator
1 Best Buy0 Worst Buys“I bought a Briggs & Stratton electric generator in 2019 for $1,300 to get us through the many power outages we live with on the eastern shore of Nova Scotia. After just 40 hrs. on the clock, it died. I called a B&S service center 1 1/2 hrs. away and he said the repair would be $400 to $500 and that he knew exactly what was wrong. In fact, he was working on one at the time that had just 7 hrs. on it. He said they have very poor electrical components and that I’d be better off buying a Generac or Honda, both of which he does not sell. Pretty sad day when a B&S service guy tells you not to buy their product. The motor itself still runs great so I’m selling that to recoup a few bucks.”
Read every report in full
FARM SHOW has run reader Best & Worst Buys since the beginning.