Hobart: what farmers say
14 reports in FARM SHOW · 12 Best Buys2 Worst Buys
Hobart stick welder
2 Best Buys0 Worst Buys“My 1966 Deere 3020 is a joy. I like the narrow front. It starts easily and is easy on fuel. I use it to mow, rake and bale.
“In 2020, I bought a Hobart stick welder at Rural King. I only did 1 lb. of small rod and melted the circuit board. Rural King wouldn’t refund, repair or replace it. I couldn’t get ahold of Hobart - their phone service is bad.”
“My best buy is a Hobart welder I bought five or six years ago. I’m really a beginning welder but have built and repaired several things. It’s worked really well.”
Hobart 135 Mig welder
1 Best Buy0 Worst Buys“I’m well pleased with my 2003 Hobart 135 Mig welder. It operates on 115 volts and is easy to operate. I use it for light steel fabrication and for doing exhaust repairs in my shop. I build hot rods and it’s very handy for this type of work. It has four settings, with one of those being an open circuit so I get full amps. I use .030 wire and 75/25 argus-carbon dioxide mix for less splatter and cleaner welds.
“My worst buy is anything electrical from
Hobart 210 wire welder
1 Best Buy0 Worst Buys“My 2003 Skag Turf Tiger zero turn riding mower, equipped with a 27 hp Kawasaki engine, is a best buy. It’s comparable in quality to Exmark mowers, which I’ve also owned. I did have one problem with the Skag a couple weeks after I bought it. I was mowing next to a heavy rubber mat, which accidentally got sucked up into the deck. The machine stopped dead in its tracks. The engine was running at top speed, and I was sure I had broken the crankshaft. But luckily all that broke was a lower pulley on the mower deck, and it was covered by the warranty. The dealer sent a replacement pulley to my house so I could fix it myself. I love this machine.
“Last December I bought a Hobart 210 wire welder. I haven’t yet tapped into the full potential of this machine, even though I’ve already used it to weld thick metals. It’s a good welder.”
Hobart 250 amp
1 Best Buy0 Worst Buys“Our 1996 Husqvarna 55 chain saw is a best buy. It starts easy and performs flawlessly. We had some problems with it at first but the dealer went out of his way to solve them.
“Our Hobart 250 amp MIG welder hasn’t needed any service at all in 10 years. It does a great job on everything from sheet metal to heavy repair work.
“I’ve learned never to buy any bargain priced tools. You get what you pay for. When it’s Sunday afternoon and you’ve got a breakdown, a tool that doesn’t break is worth every penny.”
Hobart Champion welder equipped
0 Best Buys1 Worst BuyCharles owns a 2000 Chevrolet Silverado 1/2-ton, 2-WD pickup that recently got to 333,333 trouble-free miles. “This is the toughest truck I’ve ever owned. I use it to pull big trailers and to haul big loads. I change the oil only about every 12,000 to 15,000 miles, yet the engine still runs great.
“My worst buy is my Hobart Champion welder equipped with a Kohler engine and 10,000-watt generator. I store this welder in an enclosed trailer and take good care of it, yet at 56 hrs. the engine valves and push rods failed. Neither Kohler nor the welder dealer would help.”
Hobart Handler 125 welder
1 Best Buy0 Worst Buys“My 2002 Hobart Handler 125 welder is my best buy (www.northerntool.com). This welder has saved me a lot of money by allowing me to fix all sorts of equipment by myself. The only negative is the welding wire costs too much.”
Hobart Handler 140 wire feed welder
1 Best Buy0 Worst Buys“My Hobart Handler 140 wire feed welder does an outstanding job, even with flux core wire. It’s a much better machine than my old ‘red’ one.”
Hobart Handler 15 Mig welder
1 Best Buy0 Worst Buys“My 2001 Hobart Handler 15 Mig welder is my best buy. It’s easy to use, especially for someone without a lot of experience. It works great on light material. Overall it performs beautifully and comes with an excellent instruction booklet. I’ve never had a single problem with it. It runs equally well on electrical power or on my 6,000-watt generator.”
Hobart Handler 190 230-volt wire
1 Best Buy0 Worst Buys“I love my Hobart Handler 190, 230-volt wire feed welder which I bought with a spool gun kit. Works great for gas welding, gasless, and welding aluminum. It’s very easy to adjust for each type of welding. I should get a cut from the company because many people have tried mine out and then bought one.”
Hobart Handler 190 Mig welder
1 Best Buy0 Worst Buys“I like my 2018 Hobart Handler 190 Mig welder, which I use with an H10054-10 Mig welder gun and a Hobart SpoolRunner 100 aluminum spool gun. I bought this welder to restore an IH Scout pickup from the frame on up.
“It’s really surprising how many different kinds of welds you can make with this small welder. I’ve never pushed the duty cycle, but it always hangs in there on normal welds. It can weld everything from 3/8-in. mild steel to 14 ga. metal with ease and also works great on aluminum.”
Hobart Handler 210 welder
1 Best Buy0 Worst Buys“I bought a Hobart Handler 210 welder several years ago from Northern Tool. It cost just under $900 shipped to my door. I’ve run a few 11-lb. spools of wire through it with no problems. It’s a versatile, rugged, dependable welder that’s easy to use. I’ve used it to weld everything from 20-ga. sheet metal to 3/4-in. thick steel plate. I know I’ve exceeded the duty cycle on a few 90 plus degree days but have yet to kick in the thermal overload circuit breaker.
“My friend bought a Miller 212 welder (without the spool gun) for quite a bit more than I paid for the Hobart, yet he likes my Hobart better. We took the outer cases off both units and found they’re virtually identical inside since Hobart uses Miller components. Hobart’s customer service is excellent as well. Consumables can be purchased at TSC or any welding supply shop, which is very convenient. The spool gun works well for aluminum, too.
“My Harbor Freight milling cross vise is useless. I don’t expect much from Harbor Freight tools, but this tool is bad even by their standards.”
Hobart IronMan 230 wire feed welder
1 Best Buy0 Worst Buys“My Hobart IronMan 230 wire feed welder works great (www.hobartwelders.com). It offers infinite wire feed speed control and welds like a dream. It costs much less than other comparable welders.
“My Hypertherm Powermax 30 XP plasma cutter plugs into any 120 or 240-volt power outlet. It’s lightweight and can be operated by a small pancake compressor if need be (www.hypertherm.com).”
Hobart plasma cutters
0 Best Buys1 Worst BuyRichard has had a poor experience with Hobart plasma cutters. “I bought a 2025 model; it cut only 3 ft. and quit. I also had a 2021 model that I bought at auction, but it didn’t work at all. I threw them both away.”
Read every report in full
FARM SHOW has run reader Best & Worst Buys since the beginning.