Makita power miter saw
What FARM SHOW readers say · 4 Best Buys2 Worst Buys · Chainsaws & Saws
Makita power miter saw
4 Best Buys2 Worst Buys“My Harbor Freight 5-drawer tool cart has a rated capacity of 750 lbs. Fully loaded, the large caster wheels make the cart easy to move around, even on a rough or cracked floor. This tool cart was a bargain at $169, which is only about a third the cost of other, lesser-quality products.
“Two years ago we installed eight 12-volt Trojan batteries in our solar power system and they’ve been trouble-free (www.trojanbattery.com; ph 800 423-6569). Other batteries we’ve tried have failed in as little as 6 mo.
“We built our house using a Makita 10-in. power miter saw. It cuts square every time, even after being reset to cut angles. The angles are perfect and repeatable. It’s equipped with a Freud blade, so every cut is perfectly smooth with no splintering. I highly recommend both the Makita saw and the Freud blade (www.freudtools.com; ph 800 334-4107).
“My 1994 Husqvarna 66 chainsaw has performed flawlessly with no repairs and still has the original spark plug. When the fuel hose collapsed a couple of years ago, I discovered the only available replacement hose was too short. (It’s a special molded hose with one end larger than the other and an integral grommet to seal where it goes into the tank). The dealer and company rep argued that the new, shorter fuel hose was correct, but the hose can’t reach the fuel once the tank goes below half-full. The arrogance and unhelpful attitude of this company was disappointing.”
“My 2004 Makita chop saw is my best buy. It gets used at least three days a week, and sometimes eight or ten times a day, but it just keeps on going.”
“My best buy is my 1998 Deere 7810 tractor. It has more power than a 7800 and is easier on fuel. It’s been trouble-free.
“My 1998 Case-IH 2366 combine is a dependable machine that has a lot of capacity and is a pleasure to operate. However, I wish it had a hydraulic feeder reverser on it.
“My Makita reciprocating saw is my worst buy. After the warranty expired, the saw did, too.”
“Two years ago I bought a new Makita chop saw which is my best buy. I’ve used it hard and it has done a very good job.
“We bought a plastic bottom for the un-derfeed auger on our Deere 6620 combine. After only one year of use it wouldn’t stay in place. The dealer wouldn’t do anything about it.”
Monty nominates his Barrett 32 by 8-ft. aluminum gooseneck trailer with dual tandem wheels as his “best buy”. “This trailer is built for commercial haulers. I like the versatility it offers with the floating gate option in the front. It lets me haul commercial cattle or show cattle at the same time. The company stands behind its product and offers a 6-year warranty on the welds and other parts. We’ve already worn out one truck used to pull this trailer. The trailer looks as good today as the day we bought it.
“My Makita 14-in. chop saw is my worst buy. The first Makita I bought quit working after I made only six cuts through some 3/4-in. dia. pipe. I took it back to the dealer the next day and he gave me another saw to use. That one lasted only about five days before it quit, too. Both saws weren’t used enough to even burn the factory blade up. I still haven’t gotten the second saw fixed because of dealer problems.”
Coy Prokup, Porum, Okla.: Coy says his 1990 Sears Craftsman 3/4-in, electric drill is a “worst buy”. “The chuck cracked “T can't believe what this tractor can do.” the first time used itso I returned itand got my money back. Then bought a 3/8-in. Craftsman electric drill. The first ime used it the chuck froze up and I couldn't get the bit out. I returned it also. Sears used to put out the best material and workmanship. Today they put out junk.” On the “best buy” side, “My Makita 14in. cutoff saw cuts fast. No problems.”
Own a Makita? Tell FARM SHOW how it’s held up.
Your report could appear in a future issue.