Real farmers rate what they bought, from FARM SHOW MagazineSubscribe  ·  Free issue  ·  Send us your Best or Worst Buy
Subscribe to FARM SHOW
Home › Issues › Vol. 8, No. 1 (1984)

Best & Worst Buys: FARM SHOW Vol. 8, No. 1 (1984)

44 reports from pages 10–12 · 41 Best Buys14 Worst Buys · See everything in this issue at FARM SHOW →

Best BuyWorst Buy

Ford F350

Lynn S. Loos, Baylis, Ill · Vol. 8, No. 1 (1984), p. 10

Lynn S. Loos, Baylis, Ill: “I keep hoping a tree will fall on it,’’ says Lynn, upset with her “worst buy” 1980 Ford F350 one-ton 4-WD pickup with Pos-Trac rear-end and automatic transmission. ‘‘We have a 300 bu. gooseneck trailer that we used to pull easily with our 1979 Ford 250 % ton. This one-ton can hardly pull it empty. The truck is lighter by 25% than the 1979 model and gets awful gas mileage at 5.2 mpg.’ On the plus side, she’s happy with her Deere 653 row crop head. “We rented this bean head because we had 523 acres of beans to cutand our grain platform is getting old. Because of the drought, our beans were short but this head gets them all. It eats through weeds like they're not even there.” Charles Storm, Mt. NEROM, Ss. Dak.: ““My Mix Mill e : feed grinder is my best buy,” says sCharles ; “T bought it three years ago and since that time it has performed great. Other than replacing hammers and screens, it has never required repair and we use it almost every day. Once calibrated, it records the amount of feed used for each ration.” i nieces Ee linate Sse has any problems whatsoever. No rattles, no wind noise and get 22 to 24 mph on this magnificent fully-equipped luxury car,"’ says Joseph, pleased with his 1983 Mercury Grand Marquis.

Best Buy

White

Milton White, Hyde, Md. · Vol. 8, No. 1 (1984), p. 10

Milton White, Hyde, Md.: “This tractor has been a lemon from the start,"’ says Milton, unhappy with his Deere 2940. “The clutch became very hard to push in and, at 800 hrs., it wore out. We're also having electrical problems with the air conditioner and starter. Deere says they'll make it right and they've tried but, at 1,100 hours, the clutch problem started all over again.” Milton likes his Deere 430 round baler. “It makes a very tight bale and is easy to operate, My first bale was as neat as my 200th bale.”

Best BuyWorst Buy

New Holland 420

George Ehmke, Grover, Colo. · Vol. 8, No. 1 (1984), p. 10

George Ehmke, Grover, Colo.: “This baler was junk,” says George, about his “worst buy’ Hesston 4600 baler. “It wasn't set up right at the factory. The timing was all messed up, it missed a lot of ties, and it was hard on tractors. I don't think the flywheel was heavy enough. We also had a hard time getting parts replaced.” On the plus side, he’s pleased with his New Holland 420 baler. ‘‘We traded for the baler this spring and have had no trouble at all with it. The bales are all very uniform and the hydraulic tension is really good. We also have a New Holland 282 baler that has worked well.”

Best Buy

Joseph A

Joseph A. Becker, Laddonia, Mo. · Vol. 8, No. 1 (1984), p. 10

Joseph A. Becker, Laddonia, Mo.: “I bought this car in January and have driven it over 16,000 miles without any problems whatsoever. No rattles, no wind noise and get 22 to 24 mph on this magnificent fully-equipped luxury car,"’ says Joseph, pleased with his 1983 Mercury Grand Marquis.

Best Buy

Larry Eaton, Snohomish, Wash

Larry Eaton, Snohomish, Wash. · Vol. 8, No. 1 (1984), p. 10

Larry Eaton, Snohomish, Wash.: Larry's pleased with his Deere 24A skid steer loader. ‘“‘We didn’t realize how useful it would be until we purchased it. We had considered buying one before but could see no reason to justify it until we started using sand in our freestalls. After we purchased the machine, the versatility of it simply amazed us. We now use it for many more tasks than we originally intended."

Worst Buy

Chevrolet

Craig Egelund, Bonifax, Fla. · Vol. 8, No. 1 (1984), p. 10

Craig Egelund, Bonifax, Fla.: Craig names his 1984 Chevrolet Cavalier as “worst buy”. “I had it three days and the computer went out. After two weeks, our dealer still couldn't get the part from the factory. The dealer is bending over backwards to help and will take a part off another car if necessary."

Best Buy

New Holland 462

Glen Smith, Ferndale, Wash. · Vol. 8, No. 1 (1984), p. 10

Glen Smith, Ferndale, Wash.: Glen's had trouble with his ‘ArtsWay Dion Feeder wagon. The beaters on this box are so small that green feed wraps around them and you have to shut it down to clean them off. I don’t know why the company doesn't put beaters in these wagons that won’t wrap. Dealer service is rotten.” He's pleased with his “best buy" New Holland 462 disc mower. “The mower will cut the thickest tangled grass without plugging. I can cut 20 acres in 24% hours without stopping. It's extremely well-built and doesn't take more than 40 hp. to run. Dealer service is good,” to hook up, easy to operate and a pleasure to work with,” says Ralph.

Best BuyWorst Buy

Kawasaki 3-wheeler

Robert Vohland, Farmington, III · Vol. 8, No. 1 (1984), p. 10

Robert Vohland, Farmington, III: He's disappointed with his 1982 200 Kawasaki 3-wheeler. “It won't run, has no traction, the low gear is too high and it’s worthless for chasing cattle. We also have a Yanmar 240 tractor that hasn't worked out. It overheats (no thermostat), has no traction, went through two radiators, and all we use it for is running augers and mowing weeds.”

Best Buy

Wilfred Berchimisry, Watson, Sask

Wilfred Berchimisry, Watson, Sask. · Vol. 8, No. 1 (1984), p. 10

Wilfred Berchimisry, Watson, Sask.: "We're pleased with the re- sults we've gotten with Poast," re- ports Wilfred about the new post- emergence chemical. 'We got a 99% kill on wild oats in rapeseed this spring. The crop didn't burn as with some other chemicals we've used."

Best BuyWorst Buy

Honda

Pat Connelly, Genda, Neb. · Vol. 8, No. 1 (1984), p. 10

Pat Connelly, Genda, Neb.; "It's probably the handiest farm tool I've ever purchased for livestock and grain farm use," sa,s Pat, happy with his Honda ATC 185. "It runs real well and starts on the first pull almost every time." On the negative side, he had bad luck with "Pest Gard sonic sound pest repeller. In my opinion it at- tracted birds and bugs instead of re- pelling them. It was supposed to rid the premises of rodents, bugs, birds, flys and many other pests."

Best Buy

Ralph Giffen, Barrie, Ont

Ralph Giffen, Barrie, Ont. · Vol. 8, No. 1 (1984), p. 10

Ralph Giffen, Barrie, Ont.; His "best buy" is his Deere 1209 haybine. "After cutting our first 100 acres, we only had to replace one guard and two knife sections. The 1209 is easy to hook up, easy to operate and a pleasure to work with,” says Ralph.

Best Buy

George Knebel, Ft

George Knebel, Ft. Jennings, Ohio · Vol. 8, No. 1 (1984), p. 11

George Knebel, Ft. Jennings, Ohio: “My best buy is my Saylor-Beall 5-hp. air compressor, put it in my shop, hooked it up, and it has needed nothing but normal maintenance even though it's used every day.”

Best Buy

Stephen Harris, Charlotte, N

Stephen Harris, Charlotte, N.C. · Vol. 8, No. 1 (1984), p. 11

Stephen Harris, Charlotte, N.C.: He's unhappy with the "EZY Kow lift for lifting down cows. If you tighten the lift tight enough to lift a cow, believe you would crush the cow's hip bones. My opinion is that the grips are too narrow with too much curve in them."

Best Buy

Rudy Budin, Sterling, Colo

Rudy Budin, Sterling, Colo. · Vol. 8, No. 1 (1984), p. 11

Rudy Budin, Sterling, Colo.: ‘We bought our 1979 Jeep pickup new and have had it to the dealer numerous times to have the carburetor and intake manifold worked on. The Jeep worked great the first year but after that it has really been a headache, It won't idle and dies whenever you stop to open a gate or at a stop sign. I've talked to mechanics who said Jeep's 258 cu. in. in-line 6 cyl. engine has been a real problem.” On the “best buy" side, Rudy's pleased with a Hauptner 40cc. pistol grip syringe. “It works very accurately at any setting from 1 cc to 5 ce. It’s made in Germany and is quality stuff. The American-made vaccine guns that I've had experience with are junk although the price is about the same.”

Best Buy

Chevrolet 4-WD + 1 more

David Branigan, Albin, Wyo. · Vol. 8, No. 1 (1984), p. 11

David Branigan, Albin, Wyo.: David has four ‘‘best buys’. ‘Our Case 2090 tractor has 900 trouble-free hours, Our 1086 International tractor was bought used and we've had no trouble with it. It's a pleasure to drive, very clean, and as quiet as the Case. Both our diesel vehicles — a 1983 C10 Chevrolet 4-WD pickup and our 1983 Oldsmobile Regency 98 diesel — have been best buys. We get 26 mph on the pickup and 30 mpg on the car. We had a 1978 C10 diesel and a 1978 Regency diesel before that were also best buys. I’m sold on diesels.”

Best Buy

Phil Brechbill, Auburn, Ind

Phil Brechbill, Auburn, Ind. · Vol. 8, No. 1 (1984), p. 11

Phil Brechbill, Auburn, Ind.; His "best buys" are his Allis Chalmers 6030 85 hp tractor with front wheel assist and his 14-ft. Marliss soybean drill. 'The tractor has worked perfectly. The front assist makes a real difference. You can actually feel the difference when you pull into a field without it. I pull a 6-row Deere 7000 planter 142 mph faster on slightly less fuel than I did with a 50-hp. Allis Chalmers D-17 diesel. In 450 hrs., I have changed oil per instructions but have not had to add a drop. "The drill has 6 2/3-in. spacing with 4-in. by 16-in, press wheels and an S-tine harrow-carrier pulling it. It's built heavy enough to run at 6 to 7 mph, Seed emergence has been good and yields have been excellent. We used the drill on ground where there had been only one disking of chiseled cornstalks and we still got good stands."

Worst Buy

Randy Renner, Stewardson, IIL: “We nominate our 500-gal

Randy Renner, Stewardson, III. · Vol. 8, No. 1 (1984), p. 11

Randy Renner, Stewardson, IIL: “We nominate our 500-gal. Century tandem axle trailer sprayer with 47-ft. booms as worst buy. It was purchased with a dye marker that was supposed to cover 150 acres on a quart of dye. When we got it to the field, it would only do 30 acres, It did a poor job and, at $17 a quart for the dye, is just too expensive to operate. It also has a chemical inductor designed to operate on the pressure side of the pump. This is a joke. We replumbed it to the suction side so it would work but it “A very poor job of engineering.” still works slow. The cables going to the electronic controls on the tractor are about 2 ft. short of reaching the control! box if you mount it in front of the steering wheel where it is the handiest. We have also had trouble with some of the plastic elbows and valves going bad, resulting in costly downtime. The suction hose to the pump had to be replaced because it kept collapsing. The worst problem with the sprayer is the pto shaft and pump set-up. It works fine when you drive straight, but when you turn, the pump and all connecting hoses start jumping, causing the mounting bolts for the pump to work loose, It also vibrates through the entire rear end of the tractor. We have adjusted everything possible and even tried a different pto shaft and a different tractor with no results at all. It's just a very poor job of engineering. The dealer gives us the run-around, On the positive side, the tandem axles do a very good job of crossing ditches and keeping the 47-ft. booms from bouncing. When everything is working correctly, it does a good job spraying.”

Best BuyWorst Buy

Makita + 1 more

Aaron Coe, Mt. Pleasant, Iowa · Vol. 8, No. 1 (1984), p. 11

Aaron Coe, Mt. Pleasant, Iowa: ‘'! own both a farm and a construction business. My little Ford 1900 4-WD diesel works great as a chore tractor, even hauling grain wagons in from the field. can use it all day and only consume 3.6 gal. of diesel while plowing all the gardens in town with a 2-bottom plow. In construction, I have used it to grade the job site as well as seed the lot, It brings praises from customers and neighbors on every job site. The light weight combined with the low center of gravity has allowed me to use this tractor in many back saving ways.” Aaron's “worst buy” is a Rockwell ¥-in. heavy duty hammer drill. “I use this drill primarily to drill concrete. I drilled three holes with it and the nylon gears simply wouldn't hold up. The company repaired the drill and I tried again. This time I drilled nine holes before it again broke down. To finish the job, I bought a Makita ¥2-in. hammer drill. The Makita is fantastic. It's such a pleasure to havea good and reliable tool, that I never even repaired the Rockwell drill."

Best Buy

Hughston Wooden, Shelbyville, Ind

Hughston Wooden, Shelbyville, Ind. · Vol. 8, No. 1 (1984), p. 11

Hughston Wooden, Shelbyville, Ind.: "It doesn't leave grass or brush in bunches or cut uneven swaths," says Hughston about his 'best buy" Deere 609 brush mower.

Best Buy

Ford

Gerard Laevens, Chatham, Ont. · Vol. 8, No. 1 (1984), p. 11

Gerard Laevens, Chatham, Ont.; “This plow performs very well. The dealer was helpful in setting up properly,” says Gerard, pleased with his “best buy” 151 Ford moldboard plow.

Best Buy

Melvin Reed, Cedar, Iowa: ‘‘Last year we installed an add-on wood burn

Melvin Reed, Cedar, Iowa · Vol. 8, No. 1 (1984), p. 11

Melvin Reed, Cedar, Iowa: ‘‘Last year we installed an add-on wood burning furnace on our gas furnace. After one year of splitting wood with a maul, wedges and an axe, we decided to purchase a Stotz Monster Maul from Stotz Mfg., Columbia Station, Ohio. Now we have no more flying wedges, The maul works as advertised and we sure like it,’’ says Melvin.

Best BuyWorst Buy

White + 1 more

Tony Farlow, Bahama, N.C. · Vol. 8, No. 1 (1984), p. 11

Tony Farlow, Bahama, N.C.: “FARM SHOW is my best buy. It has no bugs to be worked out. We look forward to each issue," says Tony. He says his ‘‘worst buy" is his “Green Machine weed eater. It's hard to start and the string doesn’t come out of the head when needed. You have to stop the engine and pull the string out by hand. The dealer wouldn't help. We purchased another from Echo, which is outstanding in every way.” John R. Osnes, Burke, S. Dak.: “This mower cuts lawn in half the time of any other mower.” says John, plegsed with his “best buy’’ Dixon 30-in, mower with an 8-hp. Briggs engine. “It has plenty of power and gets around real quick. My wife likes the electric start and the way it handles. “T haven't had any real wo loose, retarded the valves enough for the pistons to hit the valves. This cost me a complete major on the motor including injectors and motor blocks rebored to the tune of about $3,500. White Corp. would do nothing about the problem even though it is a manufacturing flaw because of the age of the machine. Now, 300 hours later. the same problem has occurred again, knocking out the injectors and the injector pumps as well. haven't received a bill as yet but it will be higher than the last one unless White Corp has realized it has a problem. In addition, the machine has hydraulic leaks that the dealer doesn’t seem able to resolve. The last time I got it back from the dealer for this problem, it lost over a gallon of hydraulic oil in six hours of use. This machine isn't painted yellow for nothing.”

Best Buy

Great Plains

Larry Breer, Salina, Kan. · Vol. 8, No. 1 (1984), p. 11

Larry Breer, Salina, Kan.: Larry's been pleased with his 30-ft. full press Great Plains grain drill. ‘I bought it new in September of 1982 and used it to seed 720 acres of wheat that fall. It produced a very even stand of wheat. I like the flexibility of this machine as it has three 10-ft. sections. The drill folds nicely for transport — all hydraulic. Very good workmanship and excellent service from the company.” He's also had good luck with his 11-shank Glencoe Soil Saver.’ It pulls very easily for a heavy-duty chisel. Does an excellent job of mixing trash and is practically plug proof, It’s built heavy enough to penetrate hard dry ground,” John Garnett, Callao, Mo. ‘'I’ve used this Yanmar tractor three years and have not spent a penny on it. Very economical on fuel,” says John, pleased with his 2-cyl. Yanmar diesel.

Worst Buy

White 1355D

Ivo Vogt, Carterville, Ill · Vol. 8, No. 1 (1984), p. 11

Ivo Vogt, Carterville, Ill: ‘'l would like to nominate as worst buy a 1974 White 1355D tractor. I bought this tractor atan auction with 510 hours of use in 1979. In 1982, at 1275 hrs., a gear on the crankshaft worked loose on the motor. This gear times the valves to the pistons and in working loose, retarded the valves enough for the pistons to hit the valves. This cost me a complete major on the motor including injectors and motor blocks rebored to the tune of about $3,500. White Corp. would do nothing about the problem even though it is a manufacturing flaw because of the age of the machine. Now, 300 hours later. the same problem has occurred again, knocking out the injectors and the injector pumps as well. haven't received a bill as yet but it will be higher than the last one unless White Corp has realized it has a problem. In addition, the machine has hydraulic leaks that the dealer doesn’t seem able to resolve. The last time I got it back from the dealer for this problem, it lost over a gallon of hydraulic oil in six hours of use. This machine isn't painted yellow for nothing.”

Best Buy

Bob Wegener, Lindsay, Neb

Bob Wegener, Lindsay, Neb. · Vol. 8, No. 1 (1984), p. 11

Bob Wegener, Lindsay, Neb.: ‘Our Almaco Bean Machine manufactured by Almaco in Nevada, lowa, is our best buy. Our only problem when we bought it was that it had 2-WD so we had trouble getting through ditches on our hilly ground. The company took it back and changed it to allwheel drive and now it goes anywhere. The 18-hp. Briggs motor is plenty big and it does 160 acres on 10 gal. of gas. We take eight 36-in. rows with three people and cover from 60 to 100 acres a day."

Best Buy

Larry Donham, Gardner, Kan

Larry Donham, Gardner, Kan. · Vol. 8, No. 1 (1984), p. 11

Larry Donham, Gardner, Kan.: He's happy with his More Store outside breather bag for his 32-ft. Harvestore silo, made by Thompson Enterprises, Courtland, Kan, ‘‘It allowed me to remove the breather bags from my silo so I could get an extra 1,000 bu. of storage in my silo. It cost less than ¥ the cost of adding five extra feet to the silo.” “TI get an extra 1,000 bu. of storage in my silo.”

Best BuyWorst Buy

White

Dale D. Grovek Troy, Ohio · Vol. 8, No. 1 (1984), p. 11

Dale D. Grovek Troy, Ohio: "I've been happy with how well the machine is made and the fact that it’s never been down a full day in five years use, It's not the largest machine by far but it gives you a good day's work,” says Dale about his ‘best buy"’ 7300 White combine. Glen Hassebroek, Bancroft, S. Dak.: Heading his list of ‘best buys” is his International 1460 Axial Flow combine. ‘Puts a nice grain sample in the tank and has good capacity. I had a lot of trouble with the rotor drive belt but the dealer and International really took care of the problem. “Talso have a 3788 International 2 + 2 tractor that performs well. I pulla 20-ft. vibrashank with a 20-ft. press (Continued on next page) ae ) — awn sao hanaes _. 4.2 Best, Worst Bu (Continued from prece drill behind it. Last year, 1 drilled 80 acres of barley and drove 10 miles down the road and it used just 60 gal. of fuel. The extra traction really cov- ers the ground.” Robert Radcliffe, Cardale, Man.; “No more searching for the chuck key on drills,’ says Robert, pleased with his Rohm hand-tightened keyless chuck that attaches to his ¥a-in. Black & Decker electric drill. ‘It doesn’t slip and ruin drill shanks and will outlast most electric drills. It’s expensive but well worth the convenience.”

Best Buy

Glenn Schultz, Richwood, Ohio: “Our best buy is an Allis Chalmers Glea

Glenn Schultz, Richwood, Ohio · Vol. 8, No. 1 (1984), p. 12

Glenn Schultz, Richwood, Ohio: “Our best buy is an Allis Chalmers Gleaner N-6 combine we bought in 1979. It has a 24-ft. grain head and an 8-row, 38-in. spaced row head. We put a Tiger Jaw knife, from the Herchel Corp., Indianola, lowa, on the grain head and really like it. The more we run this machine and compare it with others, the more it impresses us. It's extremely easy to handle, quiet, well-balanced, has a large grain bin, and the operator sits in the center. To unplug the cylinder is unbelievably easy so you're able to push it to full capacity. Just an awesome machine. We've put 3,700 acres through it and yet have only 425 hrs. on the separator.”

Best BuyWorst Buy

Bill Wilkins, Lucknow, Ont

Bill Wilkins, Lucknow, Ont. · Vol. 8, No. 1 (1984), p. 12

Bill Wilkins, Lucknow, Ont.: ‘‘My worst buy is a Nesseth manure pump. It worked for the first 5 or 6 months and then the pipe plugged. When we installed it, the sides of the hopper got pushed in by the cement. So, in order to get the cylinder out, I got the torch to cut the outside flange off. The torch touched off a pocket of methane gas and the explosion blew the cylinder, myself and about 2,000 gal. of liquid manure into the barn. I called a service man in from the distributor. He spent two days working on it, told me he couldn't make it work, and gave mea bill for $750. Finally I gota backhoe and dug up the pipe and shortened it from 200 ft. back to 30 ft. and it has worked fairly well since. ‘My best buy is our 26-ft. Wil-Rich cultivator. It's five years old and has covered over 4,000 acres. The only thing we've replaced besides sweeps are a couple wheel bearings. For the last three years it has been equipped with a Harlan anhydrous kit. Pulling the wagon and extra teeth doesn't seem to bother it at all. A fine piece of equipment."

Best Buy

Linus Holthaus, Ossian, lowa; He's happy with his 'best buy" Blu-Jet 2

Linus Holthaus, Ossian, lowa · Vol. 8, No. 1 (1984), p. 12

Linus Holthaus, Ossian, lowa; He's happy with his 'best buy" Blu-Jet 2100H folding NH3 3-pt. mounted toolbar made by Thurston Mfg. Co., Thurston, Neb. "A reasonably priced heavy-built and well-engineered piece of equipment. Very convenient to operate and move with hydraulic NH3 control valve and folding wings. Parts and service available locally. On the minus side, it's 16 ft. wide in the folded position so you can't get it through 16-ft. doors. It's also too wide for moving down narrow country roads. In-line transport is available, however."

Best BuyWorst Buy

Ralph Olson, Downey, Idaho: ‘‘My best buy in recent years is an Intern

Ralph Olson, Downey, Idaho · Vol. 8, No. 1 (1984), p. 12

Ralph Olson, Downey, Idaho: ‘‘My best buy in recent years is an International 435 hay baler. I've used this baler for four years now and have had a minimum amount of trouble or repairs on the unit. I especially like the knotter mechanism. Really trouble free. “My worst buy is Anchor brand cattle insecticide ear tags. After a short time they break off just below the attaching button. I have complained to my supplier with no results and am very disappointed with the product. Other cattlemen should beware.”

Best Buy

New Holland TR-85

Brad Haley, Earth, Tex. · Vol. 8, No. 1 (1984), p. 12

Brad Haley, Earth, Tex.: ‘Our New Holland TR-95 combine replaced our New Holland TR-85. The increase in capacity is amazing along with the excellent job of threshing and the clean grain sample. In my opinion it is superior to all other brands have tried. We're also pleased with our New Holland 852 baler. It makes an excellent sized bale that keeps well and feeds well.”’ the 6 gal. range,” says Gerald, happy with his Deere 4640 tractor.

Best Buy

Gerald Nakaerts, Clifton, III

Gerald Nakaerts, Clifton, III. · Vol. 8, No. 1 (1984), p. 12

Gerald Nakaerts, Clifton, III.: ‘'Excellent performance, uses little oil, has power enough to pull an 11%-ft. Soil Saver at 62 mph 8 to 10 in. in the ground, and fuel consumption is in the 6 gal. range,” says Gerald, happy with his Deere 4640 tractor.

Best Buy

Albert Van De Weert, Dryden, N

Albert Van De Weert, Dryden, N.Y. · Vol. 8, No. 1 (1984), p. 12

Albert Van De Weert, Dryden, N.Y.: 'Our Deere 2750 tractor, equipped with a 7-ft. bucket and cab, is our best buy," says Albert. 'We used it to fill our bunker silo this year and it did a fine job. Other years we had to hire a small bulldozer for the last 100 loads to top the silo off. But with the 4-WD, there was no problem. The price tag on the tractor was steep but if it performs as our other Deere equipment has in the past, it will be worth it."

Best Buy

Stihl

Fred Dale, Davis, Okla. · Vol. 8, No. 1 (1984), p. 12

Fred Dale, Davis, Okla.: “It does a better job cutting than any saw I've ever owned. Has plenty of power for any job and has been trouble-free. It always starts easy. Since buying it two years ago, all I’ve had to do is sharpen the chain and replace it when worn,” says Fred, pleased with his Stihl Farm Boss chain saw. He's had trouble with his half-ton Jeep 1979 pickup. “We bought it new and from the beginning it only got from 6 to 8 mpg on fuel. After 14 months and approximately 12,500 miles, it needed a valve job. This did not improve fuel consumption. Have also had the carburetor rebuilt two times with no improvement. I finally installed propane and now it’s even worse than when it ran on gasoline. At 38,138 miles, I've kept the body in like-new condition, but am unable to find any dealer interested in trading for it.”

Best Buy

Chevrolet S-10

Bob Fuhs, Ft. Branch, Ind. · Vol. 8, No. 1 (1984), p. 12

Bob Fuhs, Ft. Branch, Ind.: He likes his 1983 Chevrolet S-10 4-WD pickup. “I've had it for almost a year and drive it seven days a week. I haven't had a single problem with the truck nor have I taken it back to the dealer for any service. It rides good and drives excellent. The V-6 engine gets great mileage and has good power."

Best BuyWorst Buy

David Rietveld, Kouts, Ind

David Rietveld, Kouts, Ind. · Vol. 8, No. 1 (1984), p. 12

David Rietveld, Kouts, Ind.: He names his Howard Roto-Spike as both “best” and ‘‘worst buy”. “It does an excellent job of incorporation and bed shaping. It’s basically well-built and durable. However, we have been very disappointed with the com“For $3,000 extra, we expected a lot more.” pany’s warranty on the bed-shaping components used on the machine. When we wore out the supposedly durable parts after 100 acres in nonabrasive soil, the company deemed this “normal” and would not stand behind it. The bed-shaping part of this machine was not thoroughly field-tested as it should have been to anticipate such premature wear. For $3,000 extra, we expected a lot more. “Another worst buy is our Wick building that we bought 14 years ago. It continues to have a leaky roof that the manufacturer contends cannot be fixed. Also, the paint on the exterior steel siding has faded. They told us no one in the farm building industry can warrant the paint on their siding. We can show anyone a poor example of how a Wick building might function and look in the future.”

Best Buy

Kenneth L

Kenneth L. Smith, Waterlook Ind. · Vol. 8, No. 1 (1984), p. 12

Kenneth L. Smith, Waterlook Ind.: Two pieces of equipment head Kenneth’s “best buy” list. ‘The International 720 toggle plow does a real nice job plowing and pulls easily. It also goes through heavy cornstalks without plugging. I'm also wellpleased with my Pioneer model 1074 chain saw. It starts easy, and cuts well with no vibration. I have had no trouble with either product.”

Best BuyWorst Buy

International Harvester + 1 more

Bill Shumate, Urbana, Ill. · Vol. 8, No. 1 (1984), p. 12

Bill Shumate, Urbana, Ill.: “The cab and chassis are well-built, the workmanship is very good, and the engine, which is built by International Harvester for Ford, is a good performer for the 420 cu. in. size of the engine. My local Ford dealer is a dealer everyone would like to have, Very thorough and provides good service. This is my first Ford product.” On the negative side, Bill lists a set of replacement diesel injectors installed in his 1975 Allis Chalmers 7060 tractor. ‘‘In 75 hours, two injector tips went bad. My dealer replaced them quickly for me but it was a nuisance. The rest of the tractor has given good service but the older style injectors and pump aren't very good. “Another of my best buys is FARM SHOW. It's chock full of innovative ideas a farmer can use. The Worst and Best Buys section serves as a good guide when shopping for equipment.” Gary Newton, Belfield, N. Dak.: “My best buy is a rotary cutter made by Continental Belton Co., Belton, Texas. It isn’t the heaviest made or the most expensive but I cut weeds that are 5 and 6 ft. tall. I also cut road ditches with it.”

Best Buy

Wayne Fleming, Mattoon, III

Wayne Fleming, Mattoon, III. · Vol. 8, No. 1 (1984), p. 12

Wayne Fleming, Mattoon, III.: “This tractor almost broke my father and me. We each had one and it brought on my father’s early retirement. In two year’s time, we spent about $16,000 on repairs and had lots of down time,” says Wayne about his International 1466 tractor. On the positive side, Wayne's Deere 4840 is a ‘best buy”. “It’s been performing exactly as promised. Plenty of power and comfort. Can be used for any farming operation, including hoeing, cultivating, and so on.”

Best Buy

Chevrolet 1-ton + 1 more

Murray McIntyre, Burns Flat, Okla. · Vol. 8, No. 1 (1984), p. 12

Murray McIntyre, Burns Flat, Okla.: "I bought a Double Torque 2XT auxiliary transmission for my new Chevrolet 1-ton pickup from Power Torque Industries, Inc., Ar- lington, Tex. The unit is supposed to split the gears giving you an extra set of in-between gears. In a little over a year, it failed completely once, and was removed, repaired and replaced four additional times prior to com- plete failure. In addition, it was re- sponsible for the unnecessary re- placement of three heavy-duty Chev- rolet clutches due to failure caused by oil contamination from the Double Torque transmission. "This add-on has a very bad shrill scream and overheats even with the optional oil cooler and pump. The only parts I haven't replaced, in- cluding the transmission case itself due to bad factory machining, was the Eaton electric shift unit which comes with the transmission. "The Double Torque 2XT experi- ment cost me in excess of $4,000 but my Chevy pickup is once again per- fect. The unit has been removed. If anyone wants this kind of trouble, I'll send them my old burnt transmission free." ~