Dennis Esslinger, Bern, Kan: “When I went to buy a bagger machine, checked with two competing companies, Silo-Press and Ag-Bag. made my ‘worst buy’ when I leased a Silo-Press. It wouldn't run straight or feed even and, 30 bags later, it was shot. A short lifetime. ‘My ‘best buy’ is the Ag-Bag machine, made in Blair, Neb. This machine has twice the capacity of the Silo Press, runs smooth, straight and is a treat to operate, compared to my earlier experience. My Ag-Bag machine has had 20 bags through it and shows very little wear."
Best & Worst Buys: FARM SHOW Vol. 6, No. 6 (1982)
57 reports from pages 12–15 · 49 Best Buys14 Worst Buys · See everything in this issue at FARM SHOW →
John Deere + 2 more
Frank Stake, Amberson, Penn: “It’s the worst buy I ever made,” says Frank, disappointed with his Simplex Multitherm HF-120 add-on wood furnace. “The boiler is nothing but trouble. If the electricity goes off or any part of the oil burner malfunctions, the wood boiler overheats and all the controls on the boiler are damaged and have to be replaced. This furnace doesn't do the job the salesman said it would. “I'm pleased, though, with my John Deere 567 wheel rake. It rakes linate ES: See clean, even in rough fields. The purchase price was reasonable and it has few parts to wear out. I have only replaced a few rake teeth.” Charles, Blankenship, London, Kent.: “This truck has run 223,234 miles on the original engine, rear end and transmission. All I've replaced are the clutch and waterpump,” says Charles about his ‘‘best buy” 1978 6500 series GMC truck, noting that, “The 366 cu. in. engine is number one in my book.” On the negative side, Charles had a bad experience with another truck, “The ‘worst buy’ in my life was a 1976 600 Ford truck. In 19,000 miles and 13 months, the Ford dealer in Knoxville, Tenn,, installed 6 complete 361 cu. in. engines, each one costing a tow bill of $150 to $460 and a dealer charge of $300 to $700 per engine. don’t want any more Fords, not even as a gift."’
Massey Ferguson
William J. Davis, Sheridan, Ind: “High capacity, very maneuverable, easy to operate, and gives a good grain sample, especially in corn, with very little damage to kernels,” says William, pleased with his Massey Ferguson 750 combine, William has had some problems with his Omaha Standard truck bed. “It was nol installed properly so, that when a load was put on the truck, the tires rubbed against a cross member. Two almost new rear tires were ruined.”
Allis-Chalmers
Don Losure, Chester, lowa: ‘“The absolute worst product I've ever purchased is the ‘Big 6’ farrowing house built by Economy Housing of Wahoo, Neb.,"’ says Don. “In hot weather, sows get their heads stuck in the creeps and the building has to be disassembled to get them out. Little pigs get out and can't get back in. Sows crush too many pigs, and the hardware doesn't stand up to abuse. called the company twice about problems but they already had the money and had the problems. am presently using the buildings as nurseries for weaned pigs and they work alright but are not recommendable. These buildings combine most of the labor of a pasture system with most of the expense of confinement.” On the positive side, Don likes his Allis Chalmers D-15 tractor. ‘We added a hydraulic pump and three valves to make a great loader tractor out of it. Always starts, doesn’t use much gas and hardly ever needs to be worked on.”
International Harvester
Donald Thies, Randolph, Neb: ; “I'd like to nominate my 1969 International 756 diesel tractor as ‘best buy’,”’ says Donald. “It has 6,400 hrs. and we've picked corn with it for 10 years with an International 234 mounted picker, so it hasn't been babied. A real good running machine, “I would also like to mention a 1968 Pontiac Bonneville station wagon that has 183,000 miles on it with only a timing gear replaced and a transmission repair job,”
White
Victor G. Barrick, Carlisle, Penn: “My ‘worst buy’ is a Surge 1,500 gal, bulk milk tank with a heat exchanger, I bought the tank 3 years ago and it started rusting through the enamel surface in a few months, The company replaced the tank shell with a new one which also rusted within a few months. After a year of phone calls and arguing, Surge replaced the tank again, with a unit that didn't fit the milk house and also started blistering within a month, Finally traded the tank in on a Dari-Kool milk tank, which has been excellent.” On the plus side, Victor says he's happy with his White tractors, “Owning a 2-70, 2-85 and 2-135 is a pleasure. They're reliable and have excellent cab visibility, Our dealer is good,”
Norman Overland, Churchbridge, Sask: He likes his Allis Chalmer’s 7020 tractor. ‘The price was far lower than the competition, the tractor has good power, good fuel efficiency, a quiet cab and has been almost trouble-free in the first 800 hours I've used it. Dealer service is excellent.”
Chevrolet
Fred Schooley, Waterford, Ont: "My 1978 Ford Mustang is the worst car I have ever owned, It's equipped with a 2.4 liter 4-cyl. 4-speed engine. It provides disgusting performance, requires frequent maintenance, gets very poor mileage and makes lots of noise. “Another poor buy was a machine that had a 2-cyl., 17 hp. Wisconsin Robin engine made in Japan. It has no power under load and I have replaced countless plugs, along with the star ter, fuel pump, rectifier and battery in two years. Some parts take up to 11 months for delivery.” On the “best buy" side, Fred's pleased with his 1981 Chevrolet 1 ton truck. ‘‘I like its good performance, attractive design, reasonable mileage, comfort and excellent GM financing.”
Bill Ward, Castile, N.Y: ‘My Ford 5600 is able to do much more than ever expected from a small tractor. The loader works excellent, too,” says Bill. "We bought a Kasten 325 manure. spreader last spring that is also one of our ‘best buys’. It works well and service from the company is exceptional,”
John Deere + 1 more
Donald L. Miller, Bangor, Penn: “I've been no-tilling for 10 years and this was my most trouble-free year on our stoney ground,” says Donald, pleased with “best buy” Lippi coulters mounted on his John Deere 7000 Max-Emerge planter. He bought the coulters through his John Deere dealer, Chapman Equipment, in Allentown, Penn. ‘They take half the strain away from the planter unit and cut breakage of springs, while greatly reducing down time on my 700 acres of no-till corn. We had such a beautiful corn crop would recommend these units to anyone. I bought them for $325 apiece and they're worth every cent. understand Deere is coming out with a similar unit soon. “We are also very happy with our 1981 Sierra Grande 1500 GMC 4wheel drive pickup. We've had no problems at all after one year of use."
International Harvester + 2 more
Stuart Beckman, Menlo, Kan: Stuart's pleased with his 8-row, 30-in. spaced International 800 Early Riser planter. ‘‘We bought this planter in the spring of 1982 and planted over 1,500 acres of corn, soybeans, grain sorghum, and sunflowers. Plants with better accuracy and is more stable than the TH 500 planter we traded in. especially like the large, centrally located seed hopper, ease of depth adjustment and consistent depth control. It provides good seed-to-soil contact. We had excellent stands in conditions from too wet to too dry, Possibly the best thing about this or any of International's air planters is the ease of changing the planter over for different crops. I went from planting soybeans to sunflowers in less than 10 min. Anyone buying a planter ought to look these new Internationals over twice.” Also on Stuart's “best buy” list is his International 2 plus 2 3588 tractor bought in 1981. "Good power and traction and [ like not having to fight duals all the time, A good row crop and dry land tractor. “Our John Deere 4440 is the nicest tractor on the farm but it's also the biggest fuel hog. Good comfort, visibility and power. “My most memorable ‘worst buys’ were two 1976 LM 630 Allis Chalmers cornheads. With about one hour of service each morning they worked fairly well the first year, After that, neither one would run for 12 hours at a time due to constant roller bearing and roller drive problems. I traded them for John Deere 830 cornheads, which work excellent on our 1980 Allis Chalmers L2's.”
Gene J. Stout, Elizabethtown, Ind: This chain saw does a good job of cutting but has always been hard to start and backfires so hard it jerks the starter rope out of your hand, Caution is necessary to prevent arm injury,” says Gene about his Homelite XL-12. On the plus side, “My Ford TW-10 tractor has been trouble free. It has plenty of power, is easy to handle, not too hard on fuel and is a very reliable piece of equipment. Our Dodge Rampage pickup has front-wheel drive, is wn a pleasure to drive, economical to operate and overall performance is excellent. Unfortunately, dealer service is nol too good
John Deere
Alex & David MacKellar, Alvinston, Ont: ‘This plow was very disappointing.’ savs the MackKellars, unhappy with their 5-bottom, 16-in. semi-mounted, John Deere 13501450 plow. “It was hard to pull and subject to continual breakage. It was bent, busted and broke with no warranty. We had a scrap pile of broken “We also bent and broke frogs and spent more time fixing it than plowing in the field.” and bent points with hardly any wear onthem. Wealso bent and broke frogs and spent more time fixing it than plowing in the field. We have since traded it in ona Kongskilde plow and plowed 3,000 acres before replacing the original points or any other part.”’ The Mackellars had good luck with their Wil Rich 28-ft. field cultivator. “It's been maintenance free. We covered approximately 6,000 acres in three years and have had absolutely no breakage or down time. It shows no wear in the springs or shanks.”
John Deere
Leslie Johnson, Shell Rock, Iowa: “My John Deere 4640 tractor is comfortable to drive, quiet and has lots of power. Mechanically, it has been no problem whatsoever. Deere found out the water pump bearing wasn't heavy enough and fixed it at no charge to me.” On the “worst buy" side, Leslie had trouble with a “Stan Hoist 8-in. bottom drive grain auger. The sealed bearings have gone out at least once every year since I've had it. Shear pins break in the enclosed gear box instead of by the pto gear box where they're supposed to break.” John E. DeMoss, Jr., Moro, Or.: “The Positraction feature is great. My tractor should last twice as long as comparable competing models,” says John, happy with his 1981 Versatile 895 tractor. “I like to be able to lock up the front and rear differentials for hard pulls and hillside operation and then unlock them for road moving. I also like the quietness of it, the ability to vary rpm's for field speed, and to shift up and slow the rpm's for fuel economy."
Charles Duehmig, Avilla, Ind: “All it’s good for is highway travel or for some city guy to camp in,” says Charles, disappointed with his 1981 Ford F250 pickup. ‘The body is so thin that every time you load something it dents. The plastic underneath tears out in the corn fields. The motor and transmission are alright but gas mileage is not too great.”
David Elliott, Kittanning, Penn: His “best buy" is a Kuhn 452 hay tedder. ‘You can cut heavy first crop alfalfa in the late afternoon and evening with this machine, ted the following morning and bale in the afternoon. It's also good for use on hay that gets wet in the windrow. Easy to adjust and maintain.”
Allis-Chalmers
Walter Kropf, Woodstock, Ont: “It didn't roll the grain as well or as fast as it was supposed to,”’ he reports about his “worst buy” Farmatic 6 compartment roller mill. ‘‘They changed the rolls to try and improve the rolling. It helped but it’s still not the way it could be. Also, the cows didn't eat the feed as well as the company claimed they would." Walter's pleased with his 7010 Allis Chalmers tractor. ‘‘A real smooth running engine and nice quiet cab. We like it’s maneuverability and handling.”
John Harris, LaGrande, Or: “We're very satisfied with our Century Acucarb dual fuel propane and gasoline system. We haven't sacrificed any fuel economy and the difference in fuel price will pay for the system in about 20,000 miles. It's also nice to have the flexibility of running on gasoline when propane may not be readily available.”
International Harvester
Hollis Cummings, Pulaski, Tenn: “What happened to quality control in the U.S.A.?" asks Hollis, upset by a bad experience looking for a replacement throw-out bearing for his International tractor. “When we gota new one and putitin, it was as rough as the old one. We took it back and then had to go 50 miles to get one from another dealer. Out of six new ‘What happened to quality control in the U.S.A.?” bearings at this new dealer, we found just one good one.” He's happy, though, with his 1981 Datsun 510 hatchback with a 5-speed stick. “After 18 months and 18,000 miles we haven't had a bit of trouble. It gets 35 to 42 miles per gallon and one third of our travel is on county gravel roads."
Tom Zeng, Pittstown, N.J: "" When! get done plowing, I'm ready to start planting corn, even in heavy sod and rocky ground,” says Tom, pleased with his ‘best buy’? Buster Bar mounted on his moldboard plaw and manufactured by Midwest Industries, Ida Grove, lowa. “The soil is so loose afterwards that no water sits on the surface to rot the seed, even if we get a 4-in. downpour the day after planting. Soil tilth on my heavier soils was noticeably improved last spring after one season.” His ‘‘worst buy’’ was a Goodyear truck tarp. ‘This is one of the outfits ) which advertises low cost truck tarps in national magazines. The cost is low but the quality is lower. It’s very lightweight and not at all what the ; ads lead you to believe. Besides the quality, ordered a 16 by 8-ft, and ' they sent a 20 by 8-ft. When I called long distance to California to compJain, they told me they were out of my size. could have sent the other one back but harvest was upon us and had already waited 3 months for it to come.” )
Steve Drobot, St. Paul, Alberta: His New Holland 1037 automatic bale wagon has worked out well for him. “T bale all my cereal grain straw for feed. The dealer from Elk Point let me try the machine before I bought it. I'm well-pleased with its performance.” On the minus side, Steve's had trouble with his ‘‘Tox Micrometer adjustable torque wrench. do my own tractor engine overhauls and the rachet on this wrench stripped the first day of use. can’t obtain replacement parts from the dealer.” Norman Heatherington, Tallaposa, Ga.; “After rebuilding the weight racks to lower the center of gravity and weighting it heavily to secure more even penetration of coulters on sloping land, this machine is doing a good job in rather tough conditions,” says Norman, pleased with his Marliss 7-ft. no-till 12-row drill. His “worst buy” is ‘Impro dairy whey. This product is supposed to be added to drinking water at the rate of _1cc. per head per day by means of a proportioner to greatly reduce the occurrence of mastitis and uterine infections, improve breeding, health, and provide other beneficial effects. After 7 months of use in my herd it has failed to produce any positive results that I can detect.”
Harry C. Martin, Paw Paw, Mich: As director of his local Soil Conservation District, Harry bought a Lilliston No-Till grain drill. "We bought it to introduce no-till planting of small grains and hay seed to our area. The first use in alfalfa seeding was a 100% success, It was also very successful in wheat and rye. This drill is especially good in very rough and hilly ground.”
International Harvester
Bryan Kirkpatrick, Greentown, Ind: ‘We're well satisfied with the threshing capacities of our International 1460 and 1480 Axial Flow combines. They produce an excellent quality of grain both for storage or market. We did find it necessary to set the rotor cage veins in the slow position for exceptionally heavy corn. The Axial Flow has few moving parts and is virtually maintenance free. My father and I are well pleased with them."
John Deere
Larry Allbeck, Millville, Penn: “We've had a John Deere 8200 grain ‘drill for two seasons and it’s been maintenance free. Very easy to set and weare especially pleased with its Tru-Vee openers for their accurate seed depth, particularly in soybeans."
Massey Ferguson + 1 more
Mac Ragan, Bethany, Mo: “After 3¥ years and over 3,000 hours, this tractor has only been in the shop once Best And Wo — for a new clutch. It has a good power-to-weight ratio and is good for just about any chore,”’ says Mac, pleased with his Massey Ferguson 1130 tractor. “I'm also happy with my 1980 GMC 1/2 ton 4-wheel drive pickup. bought it new and it has 45,000 miles now, It has never been in the shop, even after pulling lots of trailers, fertilizer tanks, and other equipment. The 350 engine doesn’t use oil and has plenty of power, However, the 3.07 axle ratio is too high for farmers. I'd be happier if it had a 3.73 or better. “My ‘worst buy’ is the Caterpillar 3208 engine in our Massey Ferguson 4-wheel drive tractor. wish I hadn't traded off my beloved 1972 MF 1150 for this 1805. Why didn't the company use a 640 cu, in, Perkins engine, which is in the MF 2800 and 2805, rather than this short-lived Cat?"
Dean Glenney, Dunnville, Ontario: He says his worst purchase recently has been Micro Max rotary spray nozzles. ‘‘We have terrible drift problems in even the slightest wind, getting more spray on the tractor than the field. It's impossible to use with wettable powders. Every time the amount of chemical in the tank was changed, the output of the sprayer nozzle changed,” David A. Fedun, Andrew, A\lberta: He had warranty problems with a Goodrich 23.1 by 34 rear tractor tire, “The tire had a flat spot and was out of round. In repeated calls to the company, they said the tire was either underinflated or overinflated, and that tire circumference can never be true because of the size of the tire, and so on. The tire is now 1% years old and absolutely nothing has been done, No more Goodrich rubber on our farm.”
Sterling Sutton, Sargent, Neb: His Lilliston rolling cultivator heads his “best buy” list. “You can set it so many different ways. It can be set to get grass that's in the row and still travel 6 mph. With shields, you can cultivate real small corn, or just about any crop you want.” Carl Anderson, St, Peter, Minn.: He's had trouble with BF Goodrich flotation implement tires. ‘‘The Goodrich tires on our gravity running gear blew out the first year. The sidewalls on these tires are paper thin. A very poor product.”
Scott Johnson, Badger, Minn: “I've had nothing but good luck with this pickup. couldn't believe how easy on fuel it is. Really satisfied,” says Scott, happy with his 1980 Chevrolet Luv 4 by 4 pickup. He's not pleased, though, with his “KP pistol grip grease gun. This grease gun is the worst grease gun I've ever used. It just won't push the grease out. The gasket tears in notime and then the gun won't work at all.”’
John Deere
Louie W. McCoy, Albia, Iowa: “They weren't a big purchase but I'm very pleased with my Visegrip needle nosed plier. It’s a very handy tool that should be in each of our tool14) FARM SHOW (oo boxes. Another ‘best buy’ is our John Deere lawnmower. It's very powerful and makes yard maintenance a real pleasure."
Henry Kalke, Rockford, Iowa: ‘I have both a small and a large Deutz tractor and, compared to my two U.S.-made tractors, they are 50% better on fuel, have better cabs, a bet ter ride, are quieter, easier handling and in my opinion generally better built.”
Robert A. Clark, Southington, Ohio: “My Homelite 150 chain saw ran fine for the first year but then the gas tank began to leak. I had it repaired twice and soon it leaked again As it was also hard to start, I finally traded it.” He's happy. though, with his Ford C120 skid steer loader. “It's really handy and I've discovered so many uses for it. like the controls on the hand levers. The bucket and everything is controlled by hand. Does much more than I thought possible. Stingy on gas and service is tops.”
International Harvester + 1 more
Scott Ewalt, Harmony, Minn: He says his ‘‘worst buy" is a head adaptor from Brobst and Associates, of Lincoln, Neb. ‘My local International dealer ordered an adaptor from Brobst to mount an 863 IH corn head on my New Holland combine. It wouldn't fit and, after several phone calls to Brobst, we got no satisfaction and he wouldn't give us our money back. We finally got an adaptor from Harv's Farm Supply of Giltner, Neb., that I'm very pleased with. It fits well and I got excellent service when a sprocket wore out.” Scott's also happy with an Eagle grain loss monitor sold by “The grain loss monitor was easy to install on my TR75 and works “Tt paid for itself the first week.” good, It paid for itself the first week. I like the simplicity and accuracy of the 5100 planter.”
Elwood Ripstein, Cowlesville, N.Y: ‘‘We hated to buy a foreign product but we could not find another tractor to compare with this one,” says Elwood, pleased with his Same Tiger 105. ‘The fuel economy and the price of the tractor made it by far the best value.”
Dave Panther, Chehalis, Wash: He's had good luck with his Warn 8000 electric winch that mounts permanently on his pickup. “It has been invaluable on the farm for retrieving bogged down equipment, hauling wood logs, serving as a crane when rigged through blocks overhead, and freeing the pickup that it's mounted on when it gets stuck. No breakdowns and it's easily maintained.”
John Deere
Woody Bryant, Austin, Ark: “I've used my John Deere 510 round hay baler to bale several hundred bales and have never had trouble getting them started. It rolls a tight and neat bale that stands the weather well,” reports Woody.
International Harvester + 1 more
J. Russell Angell, Mocksville, N.C: He's disappointed with his International 830 forage chopper. “It pulls hard, much harder than a John Deere. The cornhead is a joke. You can't adjust the spout to direct silage from side to side, or to the rear of the wagon, from the tractor seat. Generally poor design and workmanship on the whole machine.”
Jerry Schneider, Seymour, Ind: “My ‘worst buy’ was a bird alarm from the Av-Alarm Corp., of Eugene, Or. This alarm is supposed to scare birds with a loud scream but it really attracted them instead, The company wouldn't stand behind their product. When returned it, they sent it right back to me, They were a terrible company to do business with. “My ‘best buy’ has to be my Banebridge Hog Nursery. It comes complete with a self-contained pit,” says Jerry.
International Harvester
Kevin B. Weeks, Elizabeth City, N.C: “This combine cleans corn, wheat and soybeans as well as any combine I've ever seen,” says Kevin, pleased with his International 1460 Axial Flow combine. ‘It handles our corn and bean headers well. Quietest cab ever. Well pleased after 574 hours, Hard to pay for with $2.50 corn and $6.00 beans but it’s worth the gamble.” Kevin's ‘“‘worst buy” is his International 1486 tractor. “Before the two-year warranty expired, the transmission and rear end went out four times. They put three rear end housings in this tractor. We traded for a 1586, which is trouble-free after 1750 hours, except for one bearing in the rear end.”
Denis Roy, Domremy, Sask: ‘Our Vertec grain drier is probably as good as any on the market. It's simple and quiet. Our White 9700 selfpropelled combine seems fantastic with lots of capacity and very low loss, thanks to adjustments suggested by Ray Stueckle.”
John Deere
Tommy Griggs, Kenton, Tenn: He's upset with his Tye grain drill. “The drill is poorly constructed and made of low quality materials. We have had to replace all springs and many other parts that have worn completely out, In less than two years of service it has worn 7 or 6 limes more than normal.” His “best buys” are his two John Deere tractors, a 4440 and a 4840. “We've had no major problems and only a few minor adjustments. They're very comfortable to operate and easily serviced. Dealer service is excellent.
John Deere
Don Wogen, Marshalltown, Iowa: Don has a “best buy" John Deere 6620 sidehill combine. “I have had very little trouble with it and, on rolling ground, you can harvest faster with it than with the larger 7700 John Deere combine it replaced.”
Massey Ferguson
Bruce Atkins, Warner, Alberta: ‘It was supposed to have hydrostatic drive but that never worked properly for more than two hours at a time,” says Bruce, disappointed with his Massey Ferguson 655 self-propelled swather. ‘It broke drive chains, sprockets, and needed constant adjusting. The dealer tried to help but couldn’t cure the problems. Poor basic design."
L.G. McLoughlin, Pinedale, Wyo: He had trouble with two electric fuel transfer pumps made by ‘“Tokheim Electric. The first one ran good for a “T never gota gallon of gas out of the second one.” while and then quit. It cost about $30 to repair and worked alright for about 6 months before it quit again, never got a gallon of gas out of the second one. The dealer and company both failed to stand behind their product.” Bruce I, Hartman, Dansville, N.Y.: “It'll do anything a ring drive will do at a fraction of the cost,” says Bruce, happy with his “best buy”’ Patz 98-B silo unloader. ‘The big wheels give positive drive in soft ensilage and the optional weight transfer kit prevents the unit from sinking in soft silage conditions. We can fill one day and use this unloader the next.” Bruce had trouble with his Lancaster 18440 NuRock silo. “We noticed a series of staves were cracked upon filling. The company came and inspected the unit and after some calls, came back last spring and added extra hoops so that the silo is now safe. However, feel the construction was faulty.”
Honda + 2 more
Jimmy Lester, Lascassas, Tenn: He likes his Honda 200F, Big Red three-wheeler. ‘‘We get super performance for farm use with an attached Gravely trailer. A very satisfactory purchase that hasn't caused problems. “We are also pleased with our new 2705 Massey Ferguson tractor. It's an ultimate pleasure to bale dusty hay in a cool, clean cab,"
Chevrolet
Wilbur Easter, Green Ridge, Mo: “The hay drys faster and is easy to bale. So far it has been trouble-free. It's made in France,”’ says Wilber about his Kuhn hay rake. On the negative side, Wilbur has a minor complaint about his Chevy Luv diesel pickup. “It is a great little truck but I can't get oil filters for it. They're made in Japan and Chevy dealers don't stock enough of them.”
Dick Cleaveland, Oakland, Iowa: “Our International 1440 Axial Flow combine is my ‘best buy’,”’ says Dick. “It does a good job cleaning the grain without damaging it. On the minus side, I'm very unhappy with the brakes. Unless you weigh 400 Ibs. and stand on them, they don't work.”’ “Sencor and Sutan were my ‘worst buys’ of the year,” he continues. ‘I have had little problem with velvet leaf in the past after using Sencor but this year it didn't work. And, wherev er I didn't double the rate with Sutan for shatter cane. the fields were very grassy.”
Case
Jerome H. Zeimet, Bode, Iowa: “I bought it new and it's been a reliable machine with almost no trouble and little expense. Excellent service from the dealer,"’ says Jerome, pleased with his ‘tbest buy" 1816 Case skid loader.
John Deere
Harold Landon, Greenwood, Neb: “This combine runs smoothly, does an excellent job separating the chaff from the grain with very little grain loss. We've used it in wheat, oats, milo and soybeans with good results all around. It’s a great improvement over the 915 we owned previously,” says Harold, happy with his International Axial Flow 1460 combine, Richard Schlipt, Gridley, UlL,; “We've had this dise for a few years and still can’t get it adjusted right,” says Richard about his ‘‘worst buy” Bush Hog disk. “We have problems with the wings plugging and the whole disk fish tails when disking cornstalks. We had a factory rep out to help, but he did very little good and gave us little encouragement. also had to rebuild the hydraulic cylinder bracket frame, which broke after very little use.” Richard likes his John Deere 4400 combine outfitted with a 213 soybean head. ‘‘We bought this combine used and, even though it is an early model, it runs very smooth and the bean platform works great. “Also, our new 111 John Deere lawn mower is a pleasure to drive with its hydrostatic drive and very short turning radius. It takes the chore out of mowing the lawn.”
International Harvester
J. Clifford Good, Whitesville, N.Y: He's pleased with his Hesston 1091 mower conditioner equipped with stub guards. “We've cul a couple hundred acres of hay with no plugging on the guards, even in wet, down hay.” He's also pleased with American Breeders Service. ‘Their genetic mating service may be the best we ever paid for. The first calves as a result of recommended matings look better than any calves we've had for the past 6 years.” Michael B, Roach, Coatesville, Ind.: He's disappointed with his Last-Perch sparrow trap ‘which read about in FARM SHOW, I followed the mounting instructions supplied with the unit but sparrows ignore it. It's been installed over a year and has only trapped a dozen birds. That's over $3 a bird! Good thing still have a few cats and a BB gun.” Michael's happy with his International 496, 22 ft. 2-in., hydraulic wing fold disc. “The screw jack on the tongue makes hookup easy. It's simple to adjust. Does an excellent job of leveling. One hydraulic cylinder went bad but the dealer replaced it
Fred Krebsbach, Rochester, Minn: “We cut fuel consumption by almost 2/3 and got better weed control with less herbicide,’ says Fred, pleased with his ‘best buy’ Buffalo no-till planter and cultivator. “Yield in corn was comparable to conventional planting. Soybean yields seemed higher in no-till. We'll never go back to conventional tillage.”
John Deere
Dean L. Clouse, Murdock, Kan: His 1981 Audi 5000 auto is his best buy. “The front-wheel drive handles real well in mud or on ice and for highway driving. The five cyl. engine is economical on gas, getting around 25 mpg. A real sturdy auto backed by a good dealer. “Another best buy is Deere’s 111 lawn mower. My wife does the lawn mowing and says it handles well, does nice work and is no trouble to start and operate. Another good buy is our 1380 John Deere hay conditioner. It does a real clean job cutting hay, laying it in a nice windrow for round baling. We had a small problem at first but the company took care of it.” ~
Merrill E. Woerner, Oxford, Ind: “l bought a Ride & Beautify selfpumping lawn sprayer manufactured by Western Manufacturing Corp, Marshalltown, Iowa, and it has worked as well as the salesman and the company said it would. We have had a nice looking lawn all summer at much less than the cost of a custom service. Very happy with this purchase.”
Adrien Bouffard, Kincaid, Sask: He's happy with his Steiger ST 325 tractor, ‘Very good handling and easy on fuel. The Caterpillar motor has a lot of power, yet the noise level in the cab is very low. Service is excellent. We also have a 4-year-old 270 ST Steiger that we're happy with.”
Daniel Huschka, Brodhead, Wis: Heading his “best buy’ list'is his Koehn tractor cab made by Koehn Manufacturing of Watertown, S. Dak. “Evervthing the company says about the cab is true.” he says. “It's warm in the winter. cool in the summer. It's the only cab know of that will fit older model tractors from the 1940's and 50’s with rear mount. A good cab at an affordable price.”
Gordon Obenour, Dunkirk, Ohio: “IT didn’t know tilling the garden could be so easy, It’s easy starting, usually with one pull. Well built and takes just one hand to operate, Well worth the money,"’ says Gordon, about his “best buy" 7 hp. Troy-Bilt garden tiller.
White + 1 more
Paul R. Bodensteiner, West Union, Iowa: “I would like to nominate our White 2-135 tractor as our best buy,” says Paul. ‘It has excellent power and traction and uses less fuel per acre of work done than any other tractor we've owned, It handles very well, the cab is comfortable, the ride is smooth and all controls are within easy reach, “Another good buy is our New Holland TR70 combine. Our corn has very few cracked kernels, split beans are almost impossible to find in the grain tank and there are almost no pods or broken cobs in the grain.”
Timothy E. Beeler, Hamilton, Ohio: His ‘‘best buy” is “Delvo test P, a test for antibiotics in milk, made by GB Fermentation Industries. It prevents you from putting adulterated milk in your bulk tank,” explains Timothy, ‘We use it for every cow before her milk enters the tank. It's available through our local milk coop.”