Paslode: what farmers say
10 reports in FARM SHOW · 9 Best Buys1 Worst Buy
Paslode cordless framing nail
3 Best Buys0 Worst Buys“My Paslode cordless framing nail gun is one of the best tools I own (ph 800 222-6990; www.paslode.com). I’ve used it to help construct small buildings and to repair wooden horse fences. It speeds up the building process and is a tough, reliable tool. It’s more versatile than air compressor-powered nailers.”
“My Paslode cordless framing nail gun is my best buy. It doesn’t have a hose to drag around which allows me to tackle many construction projects by myself. It eliminates the need for someone to hold the board while a nail is started. It’ll shoot spikes as well as 8-penny nails.
“My Kuhn-Deruban round bale unroller is my worst buy. The chain was much too weak to handle 1,500-lb. silage bales, which caused individual links to snap all the time. We fabricated our own replacement links, but after a while we got tired of doing that and just parked it. We’re waiting for an opportunity to trade it in.”
“My Paslode impulse framing nail gun is easy to use and has no air lines. It’s very dependable as long as I keep it clean. It has a lot of power to drive nails. I can hang it off my belt or back pocket when climbing ladders.”
Paslode nail gun
2 Best Buys0 Worst Buys“I bought an Atlas 40-volt chainsaw and weed wacker at Harbor Freight. They are less temperamental than the gas tools I have and lighter weight. I like that they start right up.
“The best tool I’ve ever owned is my Paslode nail gun. No farm should be without one. It’s great for all kinds of construction but I especially like it for repairing wooden horse fences. It’ll nail 1 by 6 oak fence boards without pre-drilling and there’s no splitting. This nail gun is so handy we bought a second one. Nails for it are half price at Harbor Freight.”

“My Paslode framing nail gun is the handiest tool I’ve ever owned. It’s powered by a gas ‘fuel cell’. A single gas bottle will drive about 2,000 3-in. nails.”
Read the whole story →Paslode 1/2-in air stapler gun
1 Best Buy0 Worst BuysFrank’s the owner of a 2018 Paslode 1/2-in. air stapler gun designed for stapling floor decking, roof sheathing, plywood sheathing, and insulation (www.paslode.com). “I do carpentry work and bought this gun to staple OSB sheeting onto a roof. Unfortunately, the gun misfired about every other time I used it. It was really aggravating not knowing if the sheeting was stapled good or not. I returned the gun to the dealer for repairs, but it didn’t help. I finally took the safety device off the gun, and now it works much better.”
Paslode 18-ga
0 Best Buys1 Worst Buy“My 2014 Paslode 18-ga., gas cartridge nail gun fired one stick of nails but then quit working. I replaced it with a new one but got the same results. I finally got my money back and went to Harbor Freight where I bought a small air compressor, hose and 18-ga. nail gun. It has never failed and cost only about one third as much as the Paslode.”
Paslode IMCT impulse cordless framing
1 Best Buy0 Worst BuysBill likes his Paslode IMCT impulse cordless framing nailer. “I have a small hobby farm and work alone. This nailer allows me to fix, repair, and build, leaving me with one hand free to align boards and hold projects in place. One squeeze of the trigger drives the nail home. The nailer is reliable, trouble-free, and light. It speeds up my work, and saves frustration and busted thumbs.”
Paslode cordless angled finish
1 Best Buy0 Worst Buys“My Paslode cordless angled finish nailer is my best buy. I used it recently to do trim work on a new house that we built. It worked as advertised, without leaving even one ‘hammer blossom’ anywhere in the entire house. No problems of any kind. It’s an excellent tool.”
Paslode gas
1 Best Buy0 Worst Buys“It’s the most dependable hand tool I’ve ever owned, and also the toughest,” says Vincent about his Paslode gas and battery-operated nailing gun. It’s designed to use 2 to 3 1/2-in. nails.
“My 50-ft. wide Howard Rotavator tiller is a best buy. Over the years I’ve owned two of the company’s tillers and have worn them to the core, but I only broke a drive chain once.
“In just a few months, I went through two Makita 3/8-in. drive electric drills while using them to operate hole saws. I used one to cut a 1/4-in. dia. hole in 3/8-in. thick steel, and the other to cut a hole in a 2 by 4. In both cases the hole saw jammed. This company used to make a good drill.”
Read every report in full
FARM SHOW has run reader Best & Worst Buys since the beginning.