Real farmers rate what they bought, from FARM SHOW MagazineSubscribe  ·  Free issue  ·  Send us your Best or Worst Buy
Subscribe to FARM SHOW
Home › Brands › Chicago

Chicago: what farmers say

8 reports in FARM SHOW · 3 Best Buys5 Worst Buys

Chicago 1/2-in electric hammer drill

1 Best Buy0 Worst Buys
Best Buy
Gale Oswald, Milford, Neb. · Vol. 35, No. 2 (2011), p. 13

“Last year I bought a Chicago 1/2-in. electric hammer drill at Harbor Freight because I needed to drill several hundred holes in concrete. I still use this tool to drive wood screws in old, hard lumber. Sometimes Harbor Freight gets a bad rap, and no doubt sometimes it’s deserved. But I’m happy with this ‘cheap’ drill.”

Chicago 4 1/2-in electric angle grinder

0 Best Buys1 Worst Buy
Worst Buy
Simon Summy, Smithshire, Ill. · Vol. 45, No. 4 (2021), p. 14

“I like the Hercules 4 1/2-in. paddle switch angle grinder I bought at Harbor Freight. The 11-amp motor has more power and runs at higher rpm’s than most grinders, and it has a lot of torque. I use it in my welding shop. Very durable.

“My DeWalt 20-volt compact angle grinder equipped with a brushless motor has good power, but it only runs at 8,000 rpm’s compared to 11,000 rpm’s for the Hercules.

“The motor quit working on my Chicago 4 1/2-in. electric angle grinder so Harbor Freight gave me a new one. However, after having to make 4 or 5 such trade-ins, I finally upgraded to the Hercules.”

Chicago electric hammer drill

0 Best Buys1 Worst Buy
Worst Buy
Robert (Fish) Pike, Hollandale, Minn. · Vol. 30, No. 1 (2006), p. 15

“I bought my 1992 Dodge Dakota 2-WD pickup equipped with a 4-cyl. engine and 5-speed transmission used for $900. The engine is fuel efficient. I put a utility box on back that I bought from a friend for $160 and use it as a service truck. I work for a local International truck dealer so it comes in handy for service calls. I converted an air conditioning compressor into an engine-driven air compressor so it also has on-board air.”

“My Chicago electric hammer drill is my worst buy. I was able to use it only once before the gears stripped out. Lesson learned. I think we should all stop being so cheap and buy good American-made tools as much as possible. Support your neighbors and you’ll be rewarded with quality.”

Chicago pneumatic 1/2-in drive

1 Best Buy0 Worst Buys
Best Buy
Don Holdeman, Elma, Iowa · Vol. 30, No. 1 (2006), p. 15

“I like my 2005 Chicago pneumatic 1/2-in. drive air impact wrench. This wrench was advertised to have 625 ft.-lbs. I have a 3/4-in. impact wrench with 700 ft.-lbs. but this small 1/2-in. wrench will do just as much as the 3/4-in. one. I bought an adapter so that I can use my 3/4-in. sockets with the 1/2-in. impact wrench. It also has a handy torque setting on back of the gun with four settings. Small gun, big power.”

A set of gear pullers from Harbor Freight rates as his “worst buy”. “The first time I used it a bolt that holds the jaws together sheared off.”

Chicago heat gun

0 Best Buys1 Worst Buy
Worst Buy
Jack Kiser, Fremont, Ohio · Vol. 31, No. 5 (2007), p. 15

“It starts good, is fuel efficient, and has required very little maintenance,” reports Jack about the International Harvester 574 diesel tractor that he bought used.

He’s not happy with the 2004 Chicago heat gun he bought from Harbor Freight Tools. “I tried using it to soften cement on the tile floor in my kitchen but it burned out after only about five minutes of use. After junking it, I bought a Warner heat gun for less money and used it to do my entire kitchen floor. It still works great.”

Chicago variable speed reciprocating

0 Best Buys1 Worst Buy
Worst Buy
Karla Tschoepe, Paonia, Colo. · Vol. 31, No. 1 (2007), p. 14

Karla likes SealLube seal expander (New Tech International, Fraser, Mich. ph 800 434-9192; www.seallube.com). This product is said to stop rubber oil seal leaks in engines, transmissions, power steering and hydraulic systems. “I used it to stop a leak in the power steering on my backhoe. I put a SealLube in last year and the power steering is still working just fine with no leaks,” says Karla.

“My 2005 Chicago variable speed reciprocating saw is my worst buy. I was able to use it for only about five minutes when the part that holds the blade broke, rendering the saw useless.”

Chicago electric power tools

1 Best Buy0 Worst Buys
Best Buy
Randy Robey, Tehachap, California · Vol. 32, No. 1 (2008), p. 12

“I’m a handyman/mechanic and purchase tools regularly. Some of the stuff I’ve purchased from Harbor Freight is good, and some of it is junk. I like the Chicago electric power tools I bought from them, including a 10-in. industrial tile/brick saw. It has been left outside in the rain and snow but it’s waterproof so it still works good. After one year of use, all it needed was a new $5 drive belt.

“On the other hand, the brushes on my Chi-cago 1 3/4 hp router burned out after only one hour of use. Then, after I replaced the brushes, a switch burned out, all on the same day.

“A Central Hydraulics 12-ton hydraulic pipe bender, bought at Harbor Freight, works good for standard pipe but will kink if used on tubing or EMT conduit.

“My Clear Water 1-in. pump is a worst buy. In the first six months of operation the pump would seize after it sat for a day or so. I have to stick a knife or key in the fan to free it, then start the pump. Another problem is there’s no freeze drain on the bottom of the pump housing. It does work well when it’s running and it only cost $35.”

Chicago portable winch

0 Best Buys1 Worst Buy
Worst Buy
Lyle Scott, Dickinson, N. Dak. · Vol. 34, No. 3 (2010), p. 12

Lyle likes his 2000 Kubota B7100 4-WD diesel tractor equipped with a hydrostatic transmission and front-end loader. “This is a handy tractor in many ways. You’d think it would have to be twice as big to do the work it does. I replaced the battery once, but otherwise it has required only routine maintenance.”

On the “worst buy” side, he lists his Chicago portable winch. “The first time I used it I tried to pull a small Deere tractor onto a flatbed trailer. The tractor wasn’t running but luckily it had a charged battery, because the only way I could get it loaded was to assist the winch by putting the tractor in first gear. The way this winch is made you have to use a wrench to loosen a nut on one side and pull out the cable, and then tighten the nut again. Unfortunately, while using the wrench I rounded off the nut and ruined the threads. Now the winch is unusable.”

Read every report in full

FARM SHOW has run reader Best & Worst Buys since the beginning.

Subscribe to FARM SHOW