Swisher trail cutter mower
What FARM SHOW readers say · 2 Best Buys3 Worst Buys · Mowers, Lawn & Snow
Swisher trail cutter mower
2 Best Buys3 Worst Buys“The 2005 Swisher 44-in. trail cutter mower cuts good and has only needed normal maintenance.
“My 2005 Kawasaki Prairie 700 ATV is a good running machine with plenty of power.”
“My 2009 Swisher 60-in. zero-turn mower has been a nightmare. Within 15 hrs. the deck bearings that held the blades failed. The dealer told me the blades weren’t the problem and that I’d have to pay for repairs. I took the bearings apart in his parking lot and showed the mechanic that the bearings were gone and the shafts were worn out, too. They ordered the parts but wouldn’t install them because I had taken them apart.
“At 20 hrs. the frame broke in front of the seat and Swisher wouldn’t warranty it. I welded the machine back together and reinforced the frame. Then both front wheels came off. Again, they wouldn’t warranty it. I reinforced the wheel mounting brackets and then the front axle broke. Around 40 hrs. the electrical wires burned off a terminal on the key switch. That was caused by the alternator putting out too much current. I re-wired the unit myself.
“At 45 hrs. the right hydro wheel motor quit working. The machine went through two deck belts per season because the belt path takes a sharp downward turn from the engine to the deck. I bought the machine because it was made in the U.S. and thought I was getting a good product and creating jobs. The machine has just over 45 hrs. on it and the only useful parts are the engine and the pretty black paint.”
“I’m happy with my Kubota L3400 tractor. This is my third Kubota and, like the other models, it has performed beyond my expectations, requiring only routine maintenance.
“My Swisher 42-in. walk-behind mower, which I bought at Tractor Supply Co., is my worst buy. It has had a number of problems. First, the transmission wouldn’t engage in fourth gear. Second, a bare spot got worn into the safety wiring for the blades where it was routed around some deck bolts. The company sent a new wiring harness and told me how to modify the rear panel so I could get fourth gear. However, after all that the mower was still too slow. I could probably mow faster with a 22-in. push mower. Thankfully, Tractor Supply took the mower back. Swisher has good customer service, but its quality control appears non-existent.”
“My 1966 Pontiac GTO was my all-time best buy. It was a fun car to drive. I won my class at the drag strip, and in later years it handled all our family chores just fine. I wish I hadn’t sold it.”
He’s unhappy with his 2004 Swisher pull-type mower. “This mower couldn’t cut thick grass during the spring of the year. I had to stop all the time to clean it out. The grass wasn’t too tall - it was just too ‘juicy’ for this mower. The grass had to be dry like it usually is in August and September before this mower would work well.
“This mower has three defects: the blades can’t move the clippings; the baffles are installed too far from the ends of the blades; and the discharge opening is too small. After 90 hours of use the bearing on the center spindle went out, destroying both the spindle and the bearing housing. I found that four of the six spindle bearings were worn out.
“I made the necessary parts on my lathe so that I could install 30-year-old Cub Cadet spindles and bearings (because you can grease the bearings) and also new Cub Cadet ZTR blades. The mower works better with these blades; however, the baffles still need to be changed.
“I contacted the company and was told that I was mowing too fast. But low gear and half throttle was as fast as I ever went when mowing during the spring.
“I still have the Swisher; however, our new Bush Hog 2561 does our mowing now. It’s as much fun to use as my GTO was to drive in 1966.”
“It’s a pleasure to use,” reports Lyle about his “best buy” Swisher 44-in. tow-behind lawn mower. “It pulls to one side of the mower. Does a great job and doesn’t miss any grass when turning.”
Own a Swisher? Tell FARM SHOW how it’s held up.
Your report could appear in a future issue.