Real farmers rate what they bought, from FARM SHOW MagazineSubscribe  ·  Free issue  ·  Send us your Best or Worst Buy
Subscribe to FARM SHOW
Home › Brands › Mastercraft

Mastercraft: what farmers say

4 reports in FARM SHOW · 3 Best Buys1 Worst Buy

Mastercraft 1/2-in cordless impact wrench

0 Best Buys1 Worst Buy
Worst Buy
Ronald J. Fitzgerald, Seeleys Bay, Ont. · Vol. 35, No. 2 (2011), p. 14

Ronald’s pleased with the Don Knasel conversion kit he read about in FARM SHOW that makes it easy to install a V-8 engine in Ford N-Series tractors (www.awesomehenry.com; ph 937 497-9447). The kit contains all the hardware needed to connect the V-8 engine and clutch assembly to the tractor’s transmission and frame.

“I made the conversion on my Ford 8N tractor. The company supplies precise parts and is helpful in answering questions regarding assembly. They’re nice people to do business with.”

He’s disappointed with his Mastercraft 1/2-in. cordless impact wrench. “It won’t start unless I rotate the drive by hand. I took the wrench back and they replaced it free of charge, but now the replacement model is doing the same thing.”

Mastercraft 9.6-volt cordless drill

1 Best Buy0 Worst Buys
Best Buy
Wayne Sabine, Tilley, New Brunswick · Vol. 27, No. 6 (2003), p. 15

“My Mastercraft 9.6-volt cordless drill is my best buy. I received it as a gift a few years ago and have hardly pounded a nail since then. It’s probably the most useful and versatile tool I own.

“My Carraro 1200 round baler is my worst buy. I bought the first baler in this area from our local Belarus dealer. The dealer spent a lot of time with me trying to get it to work properly. However, he doesn’t seem to get a lot of support from the company. I was able to make only about 1,000 bales before I had to replace the gearbox and clutches at a cost of more than $3,000. The company couldn’t tell the dealer how to take the machine apart.

“Whenever I buy a new piece of equipment I try to buy the shop manual for it. With this baler, all I could get, besides a very basic operator’s manual, was a parts book. It appears the dealer can’t get a shop manual, either. Another company has taken over Carraro and it’s now called Galiani. From what I can find out it’s essentially the same baler.”

Mastercraft MCL522

1 Best Buy0 Worst Buys
Best Buy
Harold Leblanc, Crowley, Louisiana · Vol. 46, No. 1 (2022), p. 15

“20 years ago I bought a used TCM FD25Z4 5,000 lb. forklift with a 4 cyl. Isuzu engine. I would like to get two more of these if any readers have any for sale. Another forklift that I would buy again is a Mastercraft MCL522 with a 3-stage lift and 3 cyl. Ford diesel. Also, FARM SHOW is the greatest magazine written.

Mastercraft tires

1 Best Buy0 Worst Buys
Best Buy
Everett Medlin, Wyandotte, Okla. · Vol. 37, No. 4 (2013), p. 13

“In December of 2000 I purchased a new 2001 Dodge Ram 2500 pickup equipped with Michelin 265/75 R16 tires. At about 82,000 miles I finally replaced the tires because the tread was almost down to the wear bars. I replaced them with new Mastercraft tires. After 32,000 miles, one of the tires threw the tread completely off, causing almost $3,000 damage to the pickup. They’re the most expensive tires I’ve ever bought.”

Read every report in full

FARM SHOW has run reader Best & Worst Buys since the beginning.

Subscribe to FARM SHOW